Region : Bulgaria
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :
ISP :
Region : Others
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : 3.13.6 Build 110923 Rel.53137n
ISP :
I bought the TL-R2543ND. The hardware version is V1.2. I want to ask, is there firmware upgrading for this version . Here I see only version V1. [URL] Are they suitable for my router?
Region : Bulgaria
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :
ISP :
Region : Others
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : 3.13.6 Build 110923 Rel.53137n
ISP :
I bought the TL-R2543ND. The hardware version is V1.2. I want to ask, is there firmware upgrading for this version . Here I see only version V1.URL
Region : Canada
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP :
I'm wondering if I can install this version of the firmware: TL-WDR3600_V1_130320
It says: Notes: For TL-WDR3600(UN) V1 What is that (UN) version exactly ?
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :
ISP : I have an external HDD that I regularly use in any computer I have access.It's an HDD enclosure 2.5" 3.0 USB, with a 750GB WD HDD inside. I use it in computers with all versions of USB, even in my TV. It doens't require an external power source, and just have 01 input/output, which is a USB port.After plugging it in the router (running with the last available firmware from TP-LINK - 3.13.27 Build 121207), I entered the setup screen of the router, and under USB Settings, pressed RESCAN, but the HDD wasn't recognized.What happens is that when I plug it in the router, the LED in it starts blinking (in normal usage, the LED becomes red for a couple of seconds, and then becomes steadly blue, when it gets connected into a equipment). It is probably a matter of power, as if the router wasn't providing enough power to it when it's plugged.Afterwards, I've made the following tests:
1) Used this External HDD in 3 different equipments (a notebook, a netbook and a TV), with different versions of USB ports. It was recognized and read normally in all of them.
2) I tested a pendrive with the router. After RESCAN, it was shown normally in Storage Sharing page.
3) I have downgraded the firmware to 120509 version, plugged the HDD in the router, and once again, it was an unsuccessful try.
What I can conclude from those tests is that:
1) My External HDD is working normally;
2) The router's USB port is working properly;
3) So, if both are working, it can only be a matter of compatibility between them.
Region : UnitedKingdom
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : v1
ISP : plusnet
I have a WR2543ND router and everyday it drops the wireless connection . all the lights on the router stay on and im still connected to the router but it looses the internet connection . the windows trouble shooter says that it cannot connect to the dns server , I have to reset the router and my computer to get it working again . I Have updated the firmware but still the same
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 1
ISP : cox.net
I have downloaded the file TL-wdr3600_v1_130129.zip. Extracted the file to a temp folder. Thje file is a bin file which is a bin image wdr3600v1_en_3_13_26_up(1301).bin. I do not see any flash file to load this to the router.
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Comcast
just upgrade to the latest firmware and was checking to see if I had IPv6 going with the router but it seems like it's not enabled?I went into my local area network properties and it shows checked and obtain automatically.went into the router ipv6 support tab and it shows:
IPv6 Status
WAN
Connection Type:
DHCPv6
IPv6 Address:
[code].....
Region : Brazil
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : 3.13.6 Build 110923 Rel. 53137n
ISP :
I'm trying to use TL-WR2543ND to connect 50 tablets to my wireless network, but as it establish around 20 connections, no other tablet is able to connect to it.
I've made no custom configuration to the wireless settings of the router. Is there anything a need to do to get the 50 connections?
Region : Canada
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : 3.13.17 Build 120509 Rel.33890n
ISP : shaw
my lenovo 510 running windows 7 has the wirelss router listed in the wireless netowrk connection list but cannot connect to the router. it can connect to other routers without any problem.
Region : Brazil
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : 3.13.17 Build 120509 Rel.33890n
I have a notebook connected by Wireless and a desktop connected by cable.Sometimes my wireless connection are limited, but my computer (connected by cable) still working fine.I`ve tried to disable DHCP and input static IP address but I didn't work.I have used for almost one week without problem, and sometimes this problems happens three times in one hour.The only way to reconnect the wireless is restart the TP-LINK and my internet modem.I`m using the latest firmware version.
Region : Others
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : TL-WR2543ND_V1_121207
ISP :
I bought new smartphone - Sony Xperia U, it is with android 4.Until then I have not any problems.As soon as i activate wifi on phone - all wifi on router is down, i cannot even ping it over wifi.Ping via lan interface is ok.Tried different channels, different max speeds, but nothing works.Only everything works if i have switch router to be only B/G.
Region : UnitedKingdom
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
After setting up the newly arrived router, renaming the SSID and changing password for 2.4 GHZ AND 5 GHZ and also renaming the default router username and password, I decided to update the firmware.The procedure wiped all configuration I've made forcing me to do all over again.
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : OpenWRT
ISP : Comcast
I was having major stability issues with my TPLink WDR4300 and after a little bit of research, decided to upgrade the firmware to OpenWRT. I found a post online and followed these instructions:
1- Make sure your router is version 1.x (x can be any number).
2- Download the openwrt firmware from here: [URL]
3- Download putty command tool from here: [URL]
4- Login to your router config page (192.168.0.1) using internet explorer browser and update the firmware to openwrt. Use the firmware file you downloaded in step 2.
5- Now open Putty software you downloaded in step 3. Enter host name: 192.168.1.1, Connection Type choose: Telnet. Now click open. Now you will see the command line with black screen,
6- Now type "passwd" into the command line and press enter on the keyboard. Now choose your new password to access the router make sure password has letter and number. Repeat type password and press enter. Password should be changed now.
7- Type into the command "opkg update" and press enter on keyboard, Wait for it to do some download and updates. Once finished, type this "opkg install luci" and press enter
8- Type this into the command to enable luci "/etc/init.d/uhttpd enable" and press enter on keyboard.
9- Type this into the command "/etc/init.d/uhttpd start" and press enter on the keyboard. Now you can close Putty.
10- Open internet explorer in the address bar punch in: 192.168.1.1 and use the password you created to login to the router config page. Go to the wifi section and turn on the wifi and set up wireless security network.
Everything worked fine until I got to the last step and go to the "wifi section and turn on wifi." After a bit more digging, I noticed that there is not a "Wifi" option under the 19192.168.1.1 portal "Network" tab. After getting frustrated and more hours trying to figure it out, I elected to try and go back to stock firmware. On Luci, I selected restore to factory settings and the router did its thing and restarted. Now I can't login to Luci (obviously) since it was no longer enabled in Putty. I try and run Putty to connect to 192.168.1.1 and it just opens and immediately closes. It will not connect. I also can no longer login to (192.168.0.1). Further, when I try and run the TPLink setup disk,I receive the error "Please check the network connectivity" and "Please check the model of your router." The Wifi light on the router does not turn on (it is switched on). I'm stuck and don't know what to do! I use this router in a home office with multiple wifi users.
Region : Others
Model : TL-WDR4300
Hardware Version : V1
I want to get cleared is the routers which have USB sharing option like WDR4300, WR2543ND and WR1043ND (I know it's the wrong section to mention this model but I also have this one in my list.). How much users can connect to the USB drive at a time?. I'm talking about 40 or more than 40 users here. Can these routers handle the load on the USB port?. Would there be any problem if nearly all of the users are connected to the USB drive at the same time?
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I have a client that has a WR2543ND (House) and WDR4300 (Office/Internet) router that are located in two separate buildings about 40ft apart. He has each one hooked up to external antennas connected on the outside of the buildings. Back in December I got WDS working between the two routers and the PC in the house was able to use the Internet in the Office as well as share resources between the office and house computers. Two days ago I was down there working on his network and I was having problems setting up network shares. I discovered I wasn't able to ping from the Office PC to the House PC or vice versa and what's even stranger, I couldn't ping the House PC from the House Router (WR2543ND). I checked WDS status and on the House Router is says "Run" but on the Office Router it says "Int" but the WDS is definitely up because I am able to ping from the Office Router to the House Router, plus I am able to use TeamViewer to connect to the House computer from the Office computer. There are no firewalls enabled on Windows. Lastly the DHCP server is only running on the Office Router.
Region : Denmark
Model : TL-WDR4300
Hardware Versin : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP :
my TP-Link USB Controller after my latest firmware upgrade, and therefor my USB-printer (connected to the router) do not function any more, and i can not find a new software for the Controller
wr2543ND / very slow shared storage transfer speeds?
View 4 Replies View RelatedRegion : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225
ISP : Rogers
Ever since upgrading my firmware from 120426 to the latest(121225), one of my computer(windows xp, TP-link Nano) is frequently losing internet connectivity.I purchased the router a month ago and firmware 120426 was the version that came installed. The router would stop working about 3-4 times a week, requiring me to reboot it. Because of this I did some research online and found out about version 121225 which supposedly should improve performance and stability. After the firmware upgrade today I noticed that one of my computer is having a lot of trouble maintaining internet connectivity for more than 30 minutes. When checking wireless connectivity it would say that I am connected and that the signal strength is excellent. I'm also able to ping 8.8.8.8 but not www.google.com(I've tried ipconfig /flushdns and it doesn't solve the problem). I also have trouble accessing or pinging the router(192.168.0.1) with this computer.
Region : Australia
Model : TL-WDR4900
Hardware Version : Not Clear
If wdr 7500 will have english firmware ? I bought the router in china and now back home in Australia its all in chinese?
Region : Malaysia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : TL-WDR4300_V1_130319
ISP : unfi
I unable connect to internet after upgrade the new firmware
Region : India
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : TL-WDR4320 router
ISP :
Just buy TL-WDR4320 router but its in Chinese language can somebody provide my English Firmware so that i can use this product.
Region : Malaysia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : Unifi
I just bought this hardware, I haven't tried it yet. Will tested it when I reach home today. Someone told me that I need to update the firmware. Do I really need this, or I can just simply use the existing firmware?
Region : Brazil
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
I want to change the antennas on my wdr3600 to increase the range of the signal because my walls are too thick. I can not find TP link brand Dual Band Antennas, so I search ebay and found this:
[url]....
Any dual band RP-SMA antenna is compatible with the WDR3600? or do I need to search for something in particular?
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : wdr4300v1_en_3_13_23
ISP : comcast cable
This router worked fine until I updated the firmware downloaded from the TP-Link site. I have V1 hardware which is what the firmware was created for. Since the update the wifi continually kicks outs quite often rendering this router useless.
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : TL-WDR3600_V1_130320
ISP :
Has anyone gotten the Guest Network feature to work from the new firmware TL-WDR3600_V1_130320?I have my WDR3600 setup as an access point:TPLINK with static IP address connected via ethernet cord from the LAN port and connected to the main Verizon FIOS router which distributes DHCP IP addresses to the netwrok. Can not get the Guest Network feature to work - I see the guest SSID I created but when I connect to it, the IP address assigned is in the 169. range meaning it does not get to my main router.It may be because I have the TPLINK setup as an access point, so are there any people who have gotten Guest Network work either with the TPLINK as the main router or as an access point?
Region : Iraq
Model : TL-WDR4300
Hardware Version : V1
have TL-WDR4300 router hardware v1 but when update to the latest firmware it became unstable and disconnecting so I had to return back to older firmware the new firm ware released 12/25/2012 and it is noted for TL-WDR4300(UN) V1 my model is TL-WDR4300 V1 not (UN) so what is different between the two
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP : Centurylink
I'm using a WDR3600 router, and I'm having difficulty with getting internet access on the 5 GHz band. Right now the router is broadcasting in both 2.4 and 5 GHz as two separate APs. The 2.4 GHz band works perfectly fine, but when I connect to the 5 GHz band my device is not assigned an IP address and cannot connect to the internet (or even the router configuration page). Unfortunately, I don't have another device capable of accessing the 5 GHz band, so I can't check to see if the computer is at fault, but both the computer and the router have worked together with no problems before, and this computer has done fine in accessing other 5 GHz bands.
I have belkin n600 hd wireless dual band n router f7d8301 v1. do i need to do any firmware upgrade? should i down load and install V3 of firmware of V1 only? i want to increase / enhance the range of WiFi.
View 1 Replies View RelatedI'm about to jump on the bandwagon and drop my whr-g125 running tomato for a new wireless-n router that runs tomatousb. I can't seem to find a dual-band one that is supported.
Need:
- Wireless-n dual-band (2.4ghz+5ghz). Doesn't have to be the super fast type.. whatever is entry for this.
- At least 1 usb port for printer sharing
- Prefer gigabit, but I can live without
- Must be able to run Tomato in some form, or if I have to, run dd-wrt as a last resort.
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Comcast
I just upgraded my DLink DIR655 to WDR4300. My VOIP service has worked for the last 5 years. But with WDR4300, I'm frequently experiencing dropped calls. The call will be cut off every 20 seconds or so. This is really a deal-killer.
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23
ISP : Comcast
I have no problems connecting on a 5 GHz band or wired to the router. However any device connecting on 2.4 Ghz gets barely any bandwidth and drops after running for a short time. I have test numerous devices and have the same issue. What was odd is a device on 5GHz that worked fine had the same issue when connecting on 2.4 GHz which seems to say it is only that band. I have an old router that works fine on 2.4 GHz on channel 1 with all the security settings I used on the 4300.
Region : Netherlands
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 130129
ISP :
I've this dualband wireless router since a week.Now I found out, NFS is working very slow (actually NFS is not working at all).I have a Mede8er and a synology NAS server connected to the TP-LINK WDR3600 router.I have movie directories shared on the NAS using NFS.when I go to the NFS locations in my mede8er it takes very long before I can see the NFS mapping.When I connect the Mede8er straight to the Synology NAS server (Cross Cable connection) NFS is working as it should be.So the TP-LINK WDR3600 cannot handle the NFS protocol?
Region : UnitedStates
Model : TL-WDR4900
Hardware Version : Not Clear
Firmware Version :
ISP : Comcast
The internet connection works really well on the 2.4GHz connection and when wired. But when Im connected through the 5GHz network, I get no internet.