Terminate Split Cat 5 For Data And Voice At Patch Panel End?
May 24, 2011How do i terminate a split cat5 for data and voice at the patch panel end?
View 3 Replies
ADVERTISEMENT
Move From Patch Panel To Switch?
Mar 21, 2012I currently have the following set up in my basement: Modem to 8 port router which has cables going into a patch panel which in turn provides internet access at 8 wall outlets throughout the house. My data/video streaming needs are expanding and I have had additional wiring pulled to the new locations. I would like to know if I can bypass the patch panel and go from the Modem to a 24 port switch to individual wall plates throughout the house.
View 1 Replies View RelatedCat6 Cross Over To Patch Panel?
Sep 17, 2012Am running Cat6 cable to my cellar. I plan to run a face plate in the walls of all rooms where there will be an ethernet connection. Originally when I did this in a previous house I wired two rooms together i.e. a face plate in one room and the other end a face plate. I did a cross over cable for this so when connecting anything at the other end it would talk to the device in the other room i.e. room A NAS straight through to face plate, room B PS3 straight through to face plate for example.However as I will be connecting multiple rooms together in to a patch panel then switch / router how will this then work? For all rooms where there is face plate do I crossover all cable to the patch panel or straight through? If straight through to the patch are my patch leads then cross overs to the switch?
View 2 Replies View RelatedIDF Ethernet Jack In Closet Patch Panel?
Nov 2, 2012On my closet's patch panel, there's one ethernet jack that is labeled "IDF5", I was just wondering what it is used for.
View 3 Replies View RelatedRj45 Patch Panel Wiring Standards?
Mar 3, 2012info on RJ45 patch panel wiring standards. Is there an Australian standard that specifies exposed cable pairs be not more than 13mm at termination point (RJ45) wiring cat cable?
View 1 Replies View RelatedNetworking :: Patch Panel Installation Of WNDR3700
Nov 14, 2012Recently bought a NAS (Synology DS212j), upgraded to a gigabit router (Netgear WNDR3700), and now want to utilize the pre-wired ethernet ports in our condo. How to do this last part.
Do i just plug one of the LAN ports from the router into the wall using a Cat5e cable? Then the signal will be routed to all ethernet ports through the patch panel?
I located a patch panel in the closet, but not sure if its wired correctly or which connection goes where. I took some pics that you can see here: URL
you can see in one of the pictures that some of the cables are only connected at one side.
Home Network :: Switch Need To Be Located Where Patch Panel Is
Sep 18, 2011I am renovation my own house, and I have started to hard wire for the network/s, but I am also trying to incorporate so much more than any previous “wireless” setup I have had, well I am a bit confused to say the least.I would like to set up a home network and media server system which includes:Internet browsing (multiple rooms and wireless) File sharing, printer sharing, scanner etc Music/Video sharing/streaming, TV etc.I have started wiring (we are renovating) with Cat5e, and have just replaced the old POTS (telephone) wiring with Cat5e and taken the individual telephone wires (including the incoming telephone cable) back to one central connection unit in a network patch panel. This has improved the speed of my DSL download connection speed from 1.2mbs to 6.2mbs. unreal!, so that did get me a bit fired up!I am currently wiring data points (Cat5es from each room) back to the same panel, but to be honest I am not really sure where to go from there! Also, I have wired Sat cables back to this point ready to be connected to sat TV (dish) in case if we get it. This patch panel is in a small passageway that goes through to the garage from the house. It is conveniently located next to the mains board which I have just replaced. My original idea was to put any extra needed equipment in the same location, but looking at it, I think that I may have to think again, for there is little room. I have found a small alcove in the upstairs games room which has a shelf, and which could take any hardware, also it will be dust free (unlike the place leading to the garage). I can run as many cables as needed from this location to the patch panel, but obviously I would like to know how many, as I am not familiar with networking on this scale, my only other experience being wireless setups. For example, would the switch need to be located where the patch panel is, or else can it be on the shelf with the other stuff? (away from the panel), and the existing D-link 4 port router?? is this no longer required?Im presuming i will need an old PC or some sort of media storage device here too... no ideas with this either. Have tried asking three different computer stores, got three different answers...?!
Have I dropped a clanger wiring to the passageway, when infact any server/switch or whatever wont be in the same location?Also, I am planning on getting a MAC book, and would like to use this on the system sometimes (might not be relevant), just thought to mention. And, I was thinking of trying Linux, as I am fed up with all the windows problems. But not sure if that is a good idea either.We have TVs in the (when its finished) media room, also three other areas, which I would like to get connected so that they will be able to get either TV or watch a film from storage wow this is getting complicated and if it matters I do have a PS3, which we only really bought to use as a TV storage system/recorder.
Patch Panel To Firewall / How Current Setup Is Done There Is No Configuration Map
Mar 16, 2011I have DSL, a firewall, patch panel and hubs.The network was already in place by three previous techs. I am not sure how the current setup is done there is no configuration map.The users in office 1 are all connected to a patch panel that then connects to hubs The second office users connect to a hub that then connects to the patch panel then connects to another hub.The internet is connected to a router that will be replaced with a firewall. Should it be setup like thisdsl modem > firewall > patch panel > hubs > Nodes
View 3 Replies View RelatedLinksys Cable / DSL :: DPC 3925 Should Use A Switch Or Patch Panel
Oct 17, 2012I am holding a DPC 3925 Cable Modem to connect to the internet. The wireless is great and all but i need something more.I need to connect another 8 cat6a cables to it to complete my home network. should i use a switch or patch panel or something?And not all 8 cable will be on wired. One or two connections are needed to extend the range of the wifi. What device can i use?I've got a ps3, NAS and media box that probably need the network connections to the main DPC 3925 Cable Modem.
View 1 Replies View RelatedRouters / Switches :: Cat5e Wiring Colour Codes On Patch Panel?
Jun 16, 2011my cat5 wiring seems to b wrong,so i need the wire combination of a cat5e cable on a patch panel
View 1 Replies View RelatedCisco Switching/Routing :: 3750 Using Fiber Connection Using Patch Panel
Apr 2, 2013I have a 6500 connected to 3750 using fiber connection using patch panel.on the gig port of the 6500 give of error in Input errors, CRC and FRAME.There is no error from the 3750 gigport.
View 6 Replies View RelatedBypass Patch Panel And Go From Modem To 24 Port Switch To Individual Wall Plates?
Mar 21, 2012I currently have the following set up in my basement: Modem to 8 port router which has cables going into a patch panel which in turn provides internet access at 8 wall outlets throughout the house. My data/video streaming needs are expanding and I have had additional wiring pulled to the new locations. I would like to know if I can bypass the patch panel and go from the Modem to a 24 port switch to individual wall plates throughout the house.
View 1 Replies View RelatedCisco :: PI 1.3 Can Install Patch Before Import Data From WCS
Apr 15, 2013I am migrating WCS to PI 1.3. I read from the guide that we need to migrate to NCS 1.1.1 first and we can get the demo license from Cisco.but the demo license is only 100 unit, but my WCS has 300 license units.How can I import the wcs data to NCS? Besides, I also read from the guide that I need to install patch in NCS before migrating the data to PI 1.3.can I install the patch before i import the data from WCS?
View 2 Replies View RelatedCisco WAN :: Split Data Flows Over A Single T1
Nov 7, 2012Is it possible to split data flows on a single T1. Say 1 Flow on time-slots 5-6 and another data flow on time-slots 10-14. If one was data and the other voice would this work?
View 6 Replies View RelatedCisco WAN :: 2821 - Split Outbound Data Traffic
Feb 29, 2012I have hooked up to the Cisco 2821 router a T1 on Serial and Cable Modem to GigEth0/1 and I want to split outbound traffic so that all regular users will use G0/1 interface for web traffic and the rest of the traffic stays with the T1. I am having an issue where the users on the network are not able to use the internet when using the following config:
!
interface GigabitEthernet0/0.10
description Data
encapsulation dot1Q 50
[Code].....
Cisco :: CIPC Getting IP Address From Data Or Voice
Jan 9, 2012Since CIPC is isntalled in the PC, and PC definitely getting an IP address from the data IP network segment instead of the voice IP network segment, so how to gurantee the following? 1. How the CIPC registered to the CME/CUCM 2. How to gurantee the QoS for the CIPC's voice traffic since the source IP address of the CIPC is belong to the IP network segment?
View 4 Replies View RelatedCisco :: Voice And Data Network Using 3745 And 2811?
Sep 7, 2012I intend to deploy a voice+data network using some old 3745 and 2811. The network in effect has six 3745 in a hybrid topology at different locations and each having three WIC-2T, one WIC-4T, three NMHDV-2E1. That's pretty much juicing out the maximum from these routers These will serve as my core routers and for access I will be using my 2811s with more VWICs and lesser WIC-2T to give voice and data to subscribers. The 2811s will have links to multiple 3745s. The NMHDV-2E1 will serve for the voice needs at the 3745 locations. All the WAN links will be E1. All my telephones will be on analog voice using traditional EPABX with CEPT/ PRI E1 cards for connecting to the routers. And for data, ethernet ports.Two of the routers will have E1 links to the PSTN and Internet which has to be extended to all my folks. Now, for the tricky part, all my network modules are refurbished stuff from ebay and all the ports will have links on them. I intend to use OSPF with only the backbone area.
View 7 Replies View RelatedCisco Firewall :: ASA 5510 And Having Two Outside Interfaces For Voice And Data
Feb 13, 2012I have a question regarding firewall configurations. Is it possible to have two interfaces ( for two internet service providers) one for voice and one for data. Can I have two Outside Interfaces that one will apply to a pppoe client group and the other will apply to a static IP? Is this possible and if so What would be the steps on applying this connection? Also to note I have a point to point connection already established for the pppoe. I also have another point to point connection for data, but however I do not know how to apply this to the firewall.
View 3 Replies View RelatedCisco Switches :: Passing Voice And Data Vlans On SG200-08P?
Apr 12, 2012I'm struggling with a configuration issue on the Cisco SG200-08P. We are using the Cisco SG200-08P on a mobile cart that will go from class room to class room that will have computer and cisco Voip phone plugged into it. The issue is that each of our closets are in differnt VLANS ( 1 voice and 1 data....lets say data vlan 20 and voice vlan 2025 for conversation) and that we route to each closet.It would be great if I could just create a generic data and voice vlan to dynamically pick up what the upstream switch has however, it seems that I've been unsuccessful in doing so. I can pass the data Vlan no probablem. The upstream switch port is set to access port and a switch port access voice vlan (these are 3750x switches) If the above is not possible I guess I will take what I can get. Should I just create data vlan 20 and voice vlan2025 on the Cisco SG200-08P and make a trunk port on the Cisco SG200-08P and a trunk on the 3750x? Is there an option on the Cisco SG200-08P to tag voice traffic?I'm also concerned with VTP and I did not see an area in the Cisco SG200-08P to set that as a client and transparent mode.
View 6 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.2 Failed Authenticate With Same Voice And Data Vlan
Apr 14, 2011I have a question its posible to authenticate an cisco phone and PC with the same vlan(voice and data)when i do this configuratión , the phone and pc dont work. The phone display registering and never finished.interface FastEthernet0/5 switchport mode access switchport voice vlan 1 authentication event fail action authorize vlan 11 authentication event no-response action authorize vlan 11 authentication host-mode multi-domain authentication port-control auto authentication periodic authentication violation protect mab dot1x pae authenticator dot1x timeout tx-period 10 dot1x max-reauth-req 3 spanning-tree portfastend.
View 1 Replies View RelatedCisco Switching/Routing :: EX90 Voice And DATA VLAN On A Switch
Jun 4, 2013If we configure a Voice and Data VLAn on a switch. And connect EX90 on voice VLAN and PCwith EX90 terminals. Than can we able to share a presentation or data with EX90 or not?
View 3 Replies View RelatedCisco Switching/Routing :: Data And Voice VLANs Communication 1921
Dec 11, 2012I wanted to know about EHWIC 8-Port configuration? We create Data and Voice VLANs and assign 8 ports to the VLANs. So how do VLANS communicate with each other? We cannot make Gi0/1 as sub interfaces and assign the same subnet IP’s as of VLAN IP’s , it wont accept. On 1921 router Assume Gi0/0 we connect to MPLS WAN. What happens to Gi0/1 where do we connect this?
View 1 Replies View RelatedCisco Switching/Routing :: HP 1810 / SG 300-28P - Voice And Data All Reside On Same VLan
May 16, 2013im working in a new enviroment and want to makes some design changes to the environment. I wanted to bounce my ideas some of you folks to see if my thinking is on the right path or maybe i could do things better.
Setup:
Currently the setup that i manage includes and Sonic Wall (also dishes out dhcp), HP 1810 "Core Switch" and 3 SG 300-28P cisco managed switches. (all cisco switches tie back into the HP) The router is managed by the isp. There is only one vlan with all traffic going across it.
Obviously the glaring issue here is that voice and data all reside on the same vlan. Correct me if i am thinking incorrectly but the first step would be to create a separate vlan for the phones with its own IP scheme. currently phones are issued addresses from the 150-200 range and everything else is left for pc's, printers etc. To my knowledge the HP switch does layer 3 but i do not know much about it. There are vpn tunnels to remote offices that are used for sharepoint, email and to access other services. Trying to wrap my mind around the environment as a whole so i may be missing something obvious i could do design wise to improve.
Cisco Switching/Routing :: Configure Router 2811 For Data And Voice Network
May 24, 2012I have to configure router 2811 for Data and Voice network.However I have only one Fast Ethernet interface. [code]
what else do I need to configure on switchport on which Avaya phones are connected.And is there any extra command, i need to configure on the router and 2950 switch.
Cisco Switches :: SG200 To SG300 - Setup VLAN1 For Data And VLAN10 For Voice
Apr 8, 2013I have a customer with several SG300's providing VLAN1 for data and VLAN10 for voice. The PC's are piggy backing off the phones and showing up in the SG300 fine:
One department has recently employed more people so we have an SG200 switch to connect the computers and phones to. I don't seem to be able to get any connectivity between the new switch and the SG300 it is connecting to. I have setup VLAN1 and 10 as per the images below:
Cisco Switching/Routing :: Sge2000p / Uc520 - All Data Traffic Passing OK But Voice Will Not Work
Aug 27, 2012I have a sge2000p to install with a uc520. I have all data traffic passing ok but voice will not work. Phones to not get ip etc.
View 4 Replies View RelatedCisco Switching/Routing :: Use 861 Ethernet Router To Link LANs Data And Voice Segments Together?
Feb 5, 2013We want to use a Cisco 861 Ethernet router to link our LAN's data and voice segments together (each on separate switches). Our switches are not Layer3 so routing over them is not an option. We only use the default VLAN1 on both switches.There is a data segment 192.168.1.0/24 and a voice segment 192.168.150.0/24, each with it's own internet/WAN access (internet for the data lan and SIP provider for the voice lan).
Diagram:
internet-~--router_192.168.1.1------192.168.1.0/24_data_lan--------192.168.1.254_cisco861_192.168.150.254-----192.168.150.0/24_voice------192.168.150.1_router--~-sip_provider
This is want i want to achieve:
- Link the data and voice switches using the 861
- I want to make the Cisco 861 the default gw on both segments, but they should only route traffic destined for the other segment to each other and route all other traffic to their segment's designated internet connection. I don't want the Cisco to do any NATting and there's no need for firewalling either.
Cisco WAN :: 3845 - Correct To State That VWIC2-2MFT-T1/E1 Can Support Data In Addition To Voice
May 10, 2013I have a 3845 edge router connected to the Internet via four T1s and a HWIC-4T1/E1 card. We are adding two more T1s to the mix, and I have a VWIC2-2MFT-T1/E1 card. Here are my questions:
1. Is it correct to state that the VWIC2-2MFT-T1/E1 can support data in addition to voice?
2. I can use the HWIC and VWIC cards together to utilize the 6 T1s together?
3. Do I just add the card, configure the new slot, and add it to the same channel group?
Below is the current config regarding the existing card HWIC:
card type t1 0 0
security authentication failure rate 3 log
security passwords min-length 6
logging message-counter syslog
logging buffered 51200
[code]...
Cisco Wireless :: Users Supports 2600 Series AP Air Voice / Video / Data Average Any Document Or Link
Apr 9, 2013how many users supports the 2600 series ap air voice, video, and data average any document or link
View 3 Replies View RelatedCisco Switches :: SF300-24P / Configure Vlan 10 For Data And Vlan 20 For Voice On The Same Port?
May 12, 2011We are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
View 18 Replies View RelatedCisco :: PIX 525 Firewall / Voice Network Not Working After Data Network Migrated
Feb 28, 2012My company have a Cisco PIX 525 firewall which is cater for NOC internal data network and also voice network, the subnet for data network is 192.168.2.0/24 and the subnet for voice network is 172.16.2.0/24. someday this NOC firewall was faulty. I was migrated the data network from this NOC firewall to the other temporary firewall just at the moment. And the voice network i migrated it from where it orginal at NOC firewall to a VOIP system which actually having a connection with my temporary firewall(This temporary FW only to take the traffic of data network). After the migration of data network from old firewall to temporary firewall and also the migration of voice network from old firewall to PABX system. The subnet for data network remain the same as 192.168.2.0/24, but the subnet of voice network i edit from 172.16.2.0/24 to 192.168. 3.0/24.Now when i want to use one Cisco router 2600 to replace this temporary firewall then facing problem at the voice network....The data network after migrated from temporary firewall to new 2600 is ok, users can browsing. But when i trying to at the same time when the data network been migrated , it will affect the voice network which still located at PABX. ..user cannot make call...I was thinking reason because this voice network which currently in 192.168.3.0/24 is tight to somewhere on the 192.168.x.x at the old firewall internetwork. So, when i migrated the data network over to new router, it will also cause the failure of voice even thought after i migrated the voice system to new router.So when i do the disaster recovery back to the temporary firewall for both data and voice. The voice is resuming to normal.
View 4 Replies View RelatedCisco VPN :: ASA 5520 / Error / Split Tunnel Attributes(51) Greater Than Max Allowed Split Attributes(50)
Jul 21, 2012We have ASA 5520 acting as the VPN Server and Cisco 1941 router as EZVPN client. Since last few days client is not able to establish vpn connection. 1941 router is continuously generating the below log messages
001569: Jul 22 12:19:05.883 ABC: %CRYPTO-4-EZVPN_SA_LIMIT: EZVPN(VPNGROUP) Split tunnel attributes(51) greater than max allowed split attributes(50)
001574: Jul 22 12:19:07.835 ABC: %CRYPTO-6-EZVPN_CONNECTION_DOWN: (Client) User=vpn_user Group=VPNGROUP Client_public_addr=<client public ip> Server_public_addr=<server public ip>
004943: Jul 22 11:32:42.247 ABC: %IP_VFR-4-FRAG_TABLE_OVERFLOW: Dialer1: the fragment table has reached its maximum threshold 16
Cisco VPN :: How To Use ASA 5510 To Terminate A LAN To LAN IPsec VPN
Aug 6, 2012We have an ASA 5510 running 8.3 that we need to use to terminate a LAN to LAN IPSEC VPN.
Problem is we only have one public address available so have had to configure the link between the ASA and the Internet Router on private addresses.
Is it possible to NAT the public address to the inside or outside interface of the ASA and terminate the VPN on that interface?
