At my office we have public wireless and our Domain based wired connection is locked down tight as a drum. On my Laptop, When I want to download something, I have to disable wired and enable wireless, once I'm done, I disable wireless and re-enable wired. Is there any other better way to do this?
View 1 RepliesWin 7 Home Premium. My vpn connection to work disconnects my wired internet connection. Is there a way around that? If not, can I force the vpn to connect wirelessly while staying wired to my home network and internet? Is it even possible to have both connections active at the same time? Vista laptop uses only wireless and has no problem staying conected while using vpn.
View 5 Replies View RelatedI have 4 computers (3 laptops, 1 desktop) in a shared office. We get internet access using their wireless network. All works fine. However, I need to share a printer amongst all of the computers. The printer is LAN enabled and I would normally just put all the PCs on a hub, together with the printer and share it that way. BUT my question is can we access the internet using the wireless network and the printer using a separate wired network at the same time?
View 7 Replies View Relatedis it possible to setup a wired local area network using time capsule 2T as the router?
View 1 Replies View RelatedI've brought a SG300-10 switch and would like to connect it to an Apple Time Capsule (as the base station of my wireless network), Apple Airport Extreme (to extend my wireless network) and 3 x NAS. What is the best way to connect?
Internet > SG300 > Apple TC + NAS x 4 + Apple Airport Extreme (to extended my wireless network) + Mac Pro/iMac'sInternet > Apple TC > SG300 > NAS x 4 (connect to the SG300) + Apple Airport Extreme (to extended my wireless network) + Mac Pro/iMac'sI need the SG300 because the Apple TC doesn't have enough network ports to cennect all my other devices.
On the BEFSR41 v1 series and WRT54G series, what is the maximum value for the DHCP "Client Lease Time (in minutes)?" It seems that 2^16 -1 (65535) minutes is the max. This is about 45 days. has the max value changed with newer versions of these devices?
View 1 Replies View RelatedI have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies View RelatedI just bought a WAP321 Wireless AP. I wonder why it cannot sync with our time server automatically. Every time I reboot it, the system time become "Fri Dec 31 1999 12:00:00 UCT". I have to do the sync manually by clicking on the "Save" button under the menu Administration > Time Setting.
View 5 Replies View RelatedAI have a Dir-825 router. The 5GHz is turned off and the wirless is on G/N. I have shawcable for my isp and my firmware is 2.06 and its a Rev B Router. I also have Qos Engine on for allowing me to have 2 xboxes on Open NAT.problem is my wireless signal for some wired reason is VERY weak. A while ago it used to work really far way outside. It was around 150ft distance at 4 bars. Now for some reason I can't even go upstairs without getting a 1 or 2 bar signal.
View 3 Replies View Relatedi have had my dir-655 one year now, have never had wireless problems with it until now.my notebook's internet gets very slow somedays, i just restart my router and then internet speed works normally.i have:
Hardware Version: A4 - Firmware Version: 1.32EU
I recently purchased a X2000 ADSL modem/router combination. For some reason the current time will not stay set to the time zone. Rebooting clears the discrepancy for a short time before it drops an hour exactly. I'm in the central time zone and the setting are correct on the basic setup.?
View 1 Replies View RelatedIs the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time" information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.
View 3 Replies View RelatedI have one 2621 router i want to creat time base access list so that one of my subnet user(10.128.194.0 255.255.255.128) use only internet between 11am to 2pm.
View 15 Replies View RelatedCiso 1941 router frozen once a day, sometimes after 2 to 7 days. When the router frozen, no internet connection and cannot login/ping ethernet ports. I can login to console port and copy the error messages below. Reload the router and it will return back to normal operation. Re-installed IOS but still the same.
IOS Version 15.1(2)T2,
Cisco CISCO1941/K9 (revision 1.0) with 487424K/36864K bytes of memory.
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
[code]...
I purchased and set-up the EA4500 on Thursday. Friday my ISP (Charter) was out and worked on connection for over 2 hours due to slowness issues. Connected directly to modem I get normal ping times on whichever computer is connected. When I get the computer connected by the router (hard wired) I get very long ping responses up to 900ms. They are all over the place 30ms (I can live with that), up to the 900's. I contacted Linksys support last night, who had me update to the cloud firmware and change MT U to 1300, have not noticed a difference. I did end up doing a hard reset on the router last night after I lost tech support. We were disconnected with router rebooted, and I didn't have the patience to connect again last night.
It was so slow on my work computer, a pint to yahoo timed out. The computers connecting to router are
XP SP3 (mine)
Win 7 Home (IPV6 turned off)
Work laptop that uses VPN and VOIP
I have an e2000 wireless router and have several devices connected by ethernet cable including private data on an external hard drive. I am planning to allow a tenant in another building connect via an ethernet cable connected to my router. Can I limit that computer (tenant's computer) from accessing all other devices connected by ethernet cable to my router? I know can password protect wireless access and limit access to the internet that way -- but my question is specifically to connections by ethernet cable.
View 1 Replies View RelatedMy E4200 router no longer accepts any WIRED connections. I can connect from the modem to the computer and everything works as expected. I can connect other computers wirelessly to the router. I cannot connect any laptops WIRED to the router. Nothing has changed on the systems to restrict internet access. There is something wrong with the router and the WIRED ports. I tried going through the troubleshooting on this site but it was of little to no assistance. The Cisco Connect utility doesn't appear to accomplish anything either. My guess is because I cannot connect to the WIRED ports on the router to connect to the internet to allow for whatever troubleshooting that needs to be done.
View 2 Replies View RelatedI have a home network with a wired BEFSR41 that, for a variety of reasons, MUST be manually IP configured (DHCP off). All computers and other devices connected to it are manually IP configured. I desire to add a device that cannot be manually configured, and needs DHCP. I therefore need to daisy-chain two routers with the second one DHCP on (and manual IP connection to the main network). The new device needs two-way internet access, but doesn't care if it sees any other current network devices. I've tried several configurations, none seem to work.
View 3 Replies View RelatedI have a WAP54G in my basement shop, wired to our main router upstairs, which is a Linksys BEFSR81. I'm not sure if this is an issue with the WAP or the router.
I only use the laptop computer in the shop every couple of days, but I leave the laptop plugged in and on most of the time. I used to have the power settings such that it didn't power down completely even after a long time. With that setup, if i didn't use the computer for several days, it would find that the connection to the router had died. The wireless link would report that it had a solid connection, but I couldn't connect to anything. Power cycling the WAP always fixed this.
Recently, I decided to save some wear & tear on the laptop drive, and adjusted the power settings to go to standby after a couple of hours. Now, it seems I can't even go one day without losing my connection.
I am running the latest frimware in the WAP, and the router is version 3.1. I can't check the firmware version on the router at the moment, because the web interface is giving me a blank screen. I know from past experience that I will have to power cycle it to get it to talk to me again.
In any event, it seems like the router connection to the WAP is timing out. I set the router "client lease time" up to 10000 a while back when I first had this problem, but that is clearly not doing the trick.
I have a wireless lan and a USB Modem Can I use Both at the same time to download two files each file on a lan
View 1 Replies View RelatedI am using a desktop computer and have the router downstairs so I am using a wireless usb to connect to the internet. My router is a Linksys E1000 and the wireless adapter is a Netgear WG111v2. The problem is Every few mins I drop connection for may 5-30 secs and then the internet is fine. During that time it does not say I only have local connection or anything like that it constantly says I have internet connection even when I dont. It is very noticable when i am playing an online game on my computer. I will get a few mins in and then it will drop kicking me out of the game and by the time I get kicked out my Internet is reconnected and I can join again.
View 8 Replies View RelatedWhen I first got my DIR-655 (Hardware version B1) the Wireless would keep on turning itself off, and it needed a reboot of the unit to turn it back on again.After having upgraded to the 2.03NA version of the Firmware it seems to be working correctly and hasn't turned off for a few days now.
View 14 Replies View RelatedMy kid is heading off to college with a Toshiba Satellite E-205 laptop and a Kodak ESP Office 2150 printer. She would like to use the wireless printer option on the Kodak, which requires a wireless router. I have a D-Link DIR-655 wireless router that I can send with her.
I know her university has a very robust wireless system for Internet access, so she is going to want to use their wireless access.
So, the DIR-655 sole use will be to allow access to the printer. It will not be accessing the Internet or be cabled into the university's network.
Is it possible to operate TWO wireless connections at the same time so she can hit her university wireless and the DIR-655 so she can print wirelessly?
how do I configure the laptop and the DIR-655 to allow this kind of access?
I have a Cisco 857W router which I have aquired without cost. I want to use the wireless abilities of this router to be the wireless point to get into my home lab while I am studying for my CCNA and beyond.
I have erased it to its factory settings. There is no ADSL connection to it just yet, I might connect in to my internet connection another time. Not just yet.
I dont even know where to begin. I have searched all the internet and there is nothing really anything there to guide me to set it up from the very beginning.
I have a Cisco WRT120N Router and a Cisco Valet AM10 wireless adapter. Almost every time the computer reboots, I loose my network and I have to redo the AM10 setup. The AM10 is the only device that loses the connection, my lap top and printer do not lose the connection.
Problem 2: Everytime I upplug and replug the AM10 a window pops up saying I need to check the drive for errors but none
are found.
Problem 3: I downloaded the AM10 install program, Downloadable.Setup.AM10.1.2.10148.2. It does not work. If I try to run it Iget an error message that the setup canot be completed and to call in for support.
Problem 4: When I can get it working is shows that it is Wireless Connection 5. Why 5 and not 1? Where are the other 4?
<script id="overlay_tmpl" type="text/html">// <div id="<%= overlayId %>" class="_mp3rocket_overlay_style" style="left: <%= overlayLeft %>; top: <%= overlayTop %>; width: <%= overlayWidth %>; height: <%= overlayHeight %>"></div> // </script>
My Verizon USB connection to the internet, suddenly stopped connecting to napster. Prompt says: "Server is unavailable at this time." No one at Verizon has a clue about fixing the problem, which Napster says is a Verizon connection problem..What to do??
View 1 Replies View RelatedI have a mac and an android connected to a wireless network and can not open outlook express on both at the same time. Is that just the way it is.
View 2 Replies View RelatedI set up my Linksys wireless router BEFW11S4 with a password protection to prevent access from unauthorized users, now I can only access my internet connection from one computer at a time not simultaneously like before I introduced the password. I must have missed to turn on a switch somewhere in the set up
View 2 Replies View RelatedI use a tethered iPhone to access the Internet. We live outside of the DSL service area so this is really the only high speed internet connection I have available.Unfortunately the "wireless hotspot" feature of the phone isn't very consistent. I can get all of my computers to connect to my phone this way, but the connection is constantly dropping, and I'm always having to reboot the phone to get the computers to pick it up again. The most reliable way to use the tethering is to just plug the phone in to whichever computer I happen to be using. This does create a problem, though. If I want to print to the network computer or access a file off of one of the other computers I have to manually connect to the wireless router, because that's the only way the computers can talk to each other. In the meantime, though, I can't use the internet because my computer thinks it needs to try to connect to the internet through the wireless router, and when it can't find the internet that way it just tells me there's no connection. Nevermind that my phone is still plugged in, for some reason it doesn't want to use that connection if it can see the router.
View 7 Replies View RelatedI have two wireless connections at home from 2 different ISPs. How can make my laptop connect to both routers at the same time to make use of them?
View 1 Replies View RelatedUpon turning on the computer, the wireless will not connect. It seems to not recognize the configuration of the wireless. I have to go in and put in the key every time... and then there are times that it says "limited or no connectivity". We just had a new router/modem installed in our network just yesterday. This router/modem is in conjunction with cable tv difficulties we were having.
View 3 Replies View Relatedcan i get better speed by using two wifi adapters at the same time
View 2 Replies View Relatedi have a cisco rv110w vpn/firewall/wifi and am trying to get vpn up and runing so vp can login from home and do his work.
View 1 Replies View Related