What Happens if I Used 2 to 4 more wireless routers acting as Main Routers in my network? that their DHCP are enabled? would it cause connection Disturbance? I Have 4 Cisco Linksys E300 all of thier DHCP are enabled..so they have 192.168.2.1,192. 168. 3.1, 192.168.4.1, 192.168.5.1
View 4 RepliesWe have a SRP527W with 1.1.24 firmware.
We have DHCP disabled and have assigned a IP address of 10.65.73.254 on the Interface Setup/Lan/VLAN Settings/data_lan.
When I configure a client to use 10.65.73.254 as its DNS server it cannot resolve hostnames eg [URL]. Obviously I have 10.65.73.254 as the default gateway on the client and it can ping the external host via IP Address so it only appears to be the modems function as a DNS Server that is not working.
From the diagnostics ping I can put in [URL] and it resolved and works, so the modem is correctly getting it's DNS Settings from the ISP
main computer will not connect to internet but laptop does
View 1 Replies View Relatedmy RV042. The main login password has expired but it will not let me change it at all. Basically I try to login but get the error 'The old password has expired. Please change the password'. But with no prompt at all for a new password and just a return to the login page. Tried various different browsers, tried the old default password but nothing will work. There seems to be no way of changing it and I cannot login.
I really don't want to reset it to default as I have numerous VPN tunnels configured and various other settings.
trying to setup universal wifi extender. Lights indicate system is on and connected to my computer. however wps and link rate lights are not on.
View 1 Replies View RelatedI'm using a RV082 with latest firmware v4.0.4.02tm in one of our branch offices. Sometimes the tunnel to the main office (IPCOP 1.4.21) fails.
Both sides display the status "tunnel connected" but IP traffic doesn't go through. If i try to ping the main office using the RV082 diagnostic feature, the RV082 seems to run into a loop...the window continues refreshing without any error message and i'm not able to cancel the test. If I restart the RV082 using the web interface, the "diagnose" and VPN problem still exists, even if the web interface told me that the device did a restart.
The only solution is to to a cold restart of the RV082. After that, the VPN tunnel works again....
This problem occurred 3 times in the last 3 weeks. I never hat this problem with previous firmware versions at this ot other sites.
I have one cisco 2851 router and one watchguare firewal currently being used as the main router. I want to connect the cisco as a secondary router on the same network.
View 10 Replies View Relatedhow to connect 2 routers on different lan
View 3 Replies View RelatedI have a desktop computer which is connected to the router by cable, but when this computer is on I can't connect to the wireless network with any other devices.When I turn the main computer off though I can connect fine with any wireless device.
View 3 Replies View RelatedOur scenario requires some customization in Wireless network. We have moving Forklift machines fitted with network devices. The network device in forklift acts as a client. But it doesn't have a wireless adapter and no provisions to add a wireless adapter. There is one ethernet port.
So we have a plan to attach one AP(1262) to each forklift. this AP needs to talk to the AP whcih is connected to Wired network. The network deivce in the forklift need to talk to the root AP(1262) through the AP directly connected to it over Ethernet.
If your wireless indicator is flashing red when you discover the smurf, it can mean that someone has tried to logon with an incorrect password. this is not necessarily an attack, it could be someone you have allowed access too, who has forgotten the password? In this case entering the correct password will solve the problem.However putting your own MAC address into the filter will simply block your own machine.
View 6 Replies View RelatedI currently have a BT Home Hub 3 router and an Ubiquiti Power AP N.What I am trying to do is use the Ubiquiti access point as the main device for all connections in my house (ethernet and wireless) so that I can use the QoS settings etc. I basically want the Home Hub router to play as little role as possible in the network except for providing the ADSL internet connection.I know I need to enable DHCP on the access point but everytime I do so the devices connected to the access point lose internet connection.(BTW I have an ethernet cable connected from one of the routers LAN ports into the access point's WAN port)
View 2 Replies View RelatedCurrently I have an almost pure N environment, with the exception of 1 printer. My primary router is a WRVS400N v2, and the WAP 4410N is acting as a repeater. On the WRVS400N I have the option og g/n Mixed (which is what I use), but this option is not available to me with the WAP4410N.It seems like the WAP4410N is taking an all or nothing approach, as each speed is idividually available, or ALL speeds are available.What I would like to know is if this oversight will be resolved in a fufute firmware release so I can have both devices configured equally?
View 1 Replies View RelatedThe first router is wired to the DSL modem and works just fine as an access point with Internet access. The second router is wired from the first router using one of the 4 ports on both router hubs. The second router is visible but has no Internet. How to configure the second router regarding DHCP, LAN, WAN, DNS etc.
View 3 Replies View RelatedI cant seem to to connect to my nintendo i have a motorala surfboard SBG6580
View 1 Replies View RelatedJust got virgin internet installed in my uni house, found out that my room is the only one that doesn't get any wireless signal. So to sort this out i bought a homeplug, plugged it in by the new virgin super hub and one in my room. This works perfectly fine, but im limited by the ethernet cable, so i thought i would plug in my old dlink wireless router to see if i could make my own wireless network just for my room. I could connect to it but just cant get any internet. Ive tried making the IP adress's static and using the following settings on both:
Static IP: 82.11.73.246
IP mask: 255.255.252.0
Gateway: 82.11.72.1
Primary DNS: 194.168.4.100
Secondary DNS: 194.168.8.100
I am trying to connect 2 wireless routers to expand my wireless signal. I want to connect the router 1 (in 2d floor) to a powerline av and then get the router 2 to the powerline (in the ground floor) so i can have wireless there too. I've tried some configurations i found online, but can't get to make the network functioning. The routers and powerline av are all dlink. I don't mind having 2 networks, but it would be better to have only one
View 4 Replies View RelatedI want to connect two routers wirelessly without running cables , any easiest way without cables.
View 1 Replies View RelatedI am on the Verizon wireless router connected to my laptop and the xbox wired to laptop. I have another wireless router that i want to connect because the main router is in the basement I am on the second floor. How do I connect the xbox to the 2nd router wired?
View 1 Replies View RelatedHow do I connect to the EA6500 once it's in Bridge mode acting as a wireless access point? Checked the posts and some seem to be able to do this but, we cannot.
View 6 Replies View RelatedI currently have a BT Home Hub 3 router and an Ubiquiti Power AP N. What I am trying to do is use the Ubiquiti access point as the main device for all connections in my house (ethernet and wireless) so that I can use the QoS settings etc. I basically want the Home Hub router to play as little role as possible in the network except for providing the ADSL internet connection. How would I be able to do this?I know I need to enable DHCP on the access point but everytime I do so the devices connected to the access point lose internet connection.(BTW I have an ethernet cable connected from one of the routers LAN ports into the access point's WAN port)
View 3 Replies View RelatedI am currently playing Football manager 2011 with a friend via a network game. The game will work perfectly if I connect my Laptop to the modem directly and bypass the Wireless. However if I try to play the game while connected to the wireless then my friend is unable to connect to the game. This is becoming an issue as for me to be able to play the game I have to turn the wireless off which is getting on the nerves of other family members
View 1 Replies View Relatedi have 3 home computers using the same wireless router. 2 of them have no problems detecting and accessing internet. one computer can access at times, but many times cannot detect network. i have tried restarting my modem, the router, my computer etc. at times, it works, at times it doesn't. at times, it is ok, at other times it is not.
View 2 Replies View RelatedI have the modem feeding a router that I turned dhcp off to use it as a switch, I then have the switch feeding a ubiquiti nanostation and a wireless router (to feed house 1). The other end of the nanostation is in house 2 (1000ft away) where I have it feeding into another wireless router to feed that home hard wired and wireless.Everything works but cannot get both to work at same time.
View 3 Replies View RelatedI have 2 Linksys WRT54G laying around. Is it possible to connect from Cable Modem – D-Link wireless N router – 4 port switch – Linksys Wireless G router?The reason is that my office is in the back of the house and I have a network cable running from outside to the front of the house. The wireless N doesn’t give signal to the front of the house. I want to have wireless for the tablets and the android phones.
View 1 Replies View RelatedI just bought a sony vaio laptop and I can't connect to the wireless network, it appears back and forward a message saying that the adapter is not found and then it says it is working and then it is not found again and so no.. Tried to connect the laptop using the WPS button but it did not work either.
View 1 Replies View RelatedI have 2 wireless routers with me.
(Linksys WAG200G & USR 9111).
Now, I am using USR9111 as the primary router. But, it not enough to provide network for the whole area. So, I have planned to add another router to this wireless network.
I have 2 wireless routers with me. (Linksys WAG200G & USR 9111). Now, I am using USR9111 as the primary router. But, it not enough to provide network for the whole area. So, I have planned to add another router to this wireless network. Is it possible?
View 10 Replies View RelatedI have the D-link dir-655 wireless router connected at my cable modem and i HAD a d'link switch patched in about 40 feet away. The switch died after 45 days.To solve the problem and extend my network I purchased an identicaldir-655 router to replace the switch. My thought was that i would configure both routers the same and be able to use the same network settings to access the network throughout my house.It didn't work.I even tried changing the IP address on the second router but it did something to the modem. After resetting everything, the original router works again. D'link support says what i am trying cannot be done, but i know it can.
View 1 Replies View RelatedI have a Linksys WRT54GL router in one building and a second router in an adjacent building. I have connected each router to a MODEM that takes me to the internet. Can I configure the two routers to talk to each other and at the same time maintaining their respective internet connections
View 4 Replies View Relatedmy goal is to share my cable modem signal over my two story house using two wireless routers. The delima is that the routers don't support wireless bridging and if they did, the signal is too weak to make it worth while.
The remedy I came up with... buy a pair of powerline network adapters and connect one router to the other so I could have a good signal upstairs and then a good signal downstairs.
Downstairs, I have the cable modem connected to the Linksys WRT54G router, which has a line out to my blu ray player, wirelessly feeds a PC downstairs and then has a cable run to the powerline adapter.
Upstairs, I have a cat5 connecting the powerline adapter (which was tested and works with laptop) to the data input port on my second wireless router, the netgear wndr3400.
I can't get the netgear upstairs to pull an IP address from the linksys router downstairs over the powerline network.
I need trouble-shooting wireless network connectivity issues that arose recently:We use a Comcast modem and two WRVS4400N's as wireless routers/wireless access points.We recently got our comcast service upgraded to 100/20 and also got rid of our static ip address. As a result (I think there must be a sort of causal relationship here, but I'm not sure what it is) we can no longer connect to the internet using our wireless networks. We can connect to the wireless network, but have "No Internet Access."
View 4 Replies View RelatedI just got a cisco RV220W and I try to connect it on my wireless network as client, but it doesn't work.
View 1 Replies View Related