Computer Won't Pass The Internet IP Ping Test?
Aug 18, 2011My computer will connect to the home network but won't connect to the internet or pass the ping test.
View 4 Replies
ADVERTISEMENT
D-Link DIR-655 :: Allow ICMP 8 (Ping) Pass Through?
Dec 21, 2010I would like to passthrough ICMP 8 (ping) requests through the DIR-655 to my server. I found where to allow the router to respond to ICMP 8 requests, however, I do not want the router to responder, rather the server itself. Is there a way to pass these requests through to the server?
View 3 Replies View RelatedFailed Ping Test In Windows 7?
Aug 22, 2012My Dell Inspiron Win 7 equipped computer cannot connect to the Internet. I have a DSL router that I can wirelessly connect to, but it says no Internet access. I used the manual Intel Wireless Manual Diagnostic Tools to test my system and failed the ping test. Dialog box says "no response, default gateway,DHCP server" and indicates the ping test failed.I have checked my router and it is working nominally; other laptops in my family have Internet access just fine. My Intel Centrino Wireless N 1030 adapter is working fine. I detect no other hardware problems on my laptop.
View 7 Replies View RelatedRead A Ping And Tracert Test?
Oct 7, 2012I am currently using Time Warner Cable as my internet provider and I have been experiencing very slow internet connection speeds for the past few weeks. This has happened across multiple laptops and desktops both wireless and wired connections. I have done a ping and tracert test but am unable to read the results.
View 7 Replies View RelatedPing Test - 100% Packet Loss?
Nov 17, 2012Pinging 98.137.149.56 and had 100% packet loss; this was suggested in another thread. LAN connected at 100 Mbps BUT cannot access Internet! Windows XP HP desktop; Belkin N Router; Optimum Cablevision - Modem Scientic Atlanta "Webstar"
I am using my iPhone to access Internet.
Wireless :: How To Create BAT File To Test Ping
Sep 22, 2011how to create a .bat file to test ping with nane and ip address
View 1 Replies View RelatedCisco :: Can't Ping Out Onto Internet From A 172.16.0.0 / 16 Computer
Feb 28, 2012When I first set up the Zone based firewall I used the Wizard with a setting of "low".The issue I am now having is related to adding a new subnet on a completely different IP range. My normal network is 10.20.0.0/16 sub-netted down into /24's for each vlan.Recently I added a new VLAN with a 172.16.0.0/16 subnet. I plan to use this vlan for testing purposes. I updated NAT on the router to allow the 172.16.0.0/16 range to be NATTED.From the router I can ping anything on the 172. 16.0. 0/16 range and from a test machine in the 172.16.0.0/16 I can ping all of the 10.20.0.0/16 addresses including the router.My problem is I can not ping out onto the Internet from a 172.16.0.0/16 computer.I have checked and so far I have not been able to find any policies on the firewall saying traffic must be sourced from the 10.20.0.0/16.
View 8 Replies View RelatedLimit How Much Internet / Ping A Computer Can Take
Jul 6, 2012Whenever my sister uses her laptop it makes the routers ping really unstable. It usually lies between 200-1000 when she uses the laptop. When she turns it off the ping remains at 21. Our internet is 8mbps/0.7mbps. I have tried other laptops and had no problems, but her laptop and her general use makes it impossible to play an online game without lagg. She doesn't download anything, just plays some flash/java games, chats and webcam etc. I just can't understand why the ping becomes so unstable when she uses her laptop.What can I do to make the ping more stable? Any software I can install to limit how much ping she uses or something? Something I can buy to split the line between us or anything like that? Software that checks what she is doing that makes the ping unstable? She just had a few programs and chrome up and still ping was unstable. None of the other laptops in the house behaves this way nor any of the desktops. It also makes web pages load 5 times slower?
View 1 Replies View RelatedPing Test Failed / DHCP Server But No Response
Jan 28, 2013I connects to the wireless box and has full signal but an exclamation mark is present.I have run some tests and the IPv4 and IPv6 say they have no internet access.I also run a full test and everything passed except the ping test which failed and it said: no response:default gateway response: dhcp server it suggested disabling security firewall but i'm not sure if that's the correct thing to do or even how to do that!
View 7 Replies View RelatedUnable To Connect - Failed Ping Test - HP Laptop
Nov 3, 2011Ran a diagnostics test and failed the Ping test. I'm using the university resident internet. Called the tech place and they said they're investigating their connections and networking thing on their end. Just in case though, I want to know if there's actually something wrong with my laptop rather than their equipment.
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersHelen>IPCONFIG /ALL
Windows IP Configuration
Host Name . . . . . . . . . . . . : FATHERSCOMPUTER
Primary Dns Suffix . . . . . . . :
[code].....
Cisco Switching/Routing :: ASA 5520 - Can't Ping / Pass Traffic Through Interfaces
Apr 17, 2012I've just started a CCNA course and my lack of knowledge has me a bit stuck. My network is comprised of Cisco components and I'm semi familiar with them just from reading and looking through options. I currently am using a Cisco ASA 5520 on my network and I am trying to join another network via one of the interfaces. My network is 192.168.0.0 255.255.0.0 and my inside interface is 192.168.1.1 255.255.0.0. I enabled a second interface using a static ip of 10.0.0.1 with a subnet of 255.255.255.128. Connected to that interface, I have a Fortigate firewall at 10.0.0.2 255.255.255.128. I can ping just fine from the Fortigate network to the 10.0.0.1 interface on the Cisco ASA 5520 network, but I can not ping the 10.0.0.1 interface (or anything past it) on the ASA 5520 from any computer on the Cisco network. I've read that ACL's and NAT have to be done as well as enabling traffic between interfaces with the same security levels. (both interfaces have security levels of 100 and the option is checked to allow traffic).
Note: each network has it's own internet connection. The connection is to share information on servers on both networks with each other.
Broadband :: Receiving MAC Address Means Ping Test Success?
Apr 8, 2011We are trying to isolate the fault. From Aggregator a router, we are receiving MAC address of distant end ethernet interface of a SDH box and vice versa is also possible. However ther is no packet received. My question is does ping test is must to see if the path is through or just receiving MAC adress at both ends would mean that packets have to go over the path.
View 1 Replies View RelatedCisco Routers :: WRVS4400N And QuickVPN - Ping Test Fails Sometimes / Not Others?
Oct 23, 2009I have a new WRVS4400N VPN router and have set it up for VPN. On a separate computer I have a Verizon EVDO card so I have used that with a separate computer to access the internet on a public, routable IP address off of my network.
When I use the QuickVPN client, I wasn't able to get into my network (using ddyns.org) because I didn't have the "BLOCK WAN REQUEST" setting disabled so the router could be ping'd. Once I did that, I verified I could successfuly ping my ddyns name abc.xyz.com.
In the error log of the QuickVPN client, I still see:
2009/10/24 16:57:15 [STATUS]OS Version: Windows XP2009/10/24 16:57:16 [STATUS]Windows Firewall is OFF2009/10/24 16:57:16 [STATUS]One network interface detected with IP address x.x.x.x2009/10/24 16:57:16 [STATUS]Connecting...2009/10/24 16:57:16 [STATUS]Connecting to remote gateway with IP address:x.x.x2009/10/24 16:57:28 [WARNING]Remote gateway wasn't reached...2009/10/24 16:57:36 [STATUS]Remote gateway was reached by https ...2009/10/24 16:57:36 [STATUS]Provisioning...2009/10/24 16:57:47 [STATUS]Tunnel is configured. Ping test is about to start.2009/10/24 16:57:47 [STATUS]Verifying Network...2009/10/24 16:57:51 [WARNING]Failed to ping the LAN IP of the remote VPN Router!2009/10/24 16:57:52 [WARNING]Failed to
[code]....
I HAVE been able to make the connection successfully without any other changes to the environment. It's hit or miss, but usually a miss. Restarting QuickVPN sometimes works on the next try, but then fails if I disconnect and try again. Even when that ping error message is appearing, I am able to ping the host name at a command prompt without a problem.
Is something else on the router possibly blocking the ping requests?My router is behind a Westell F90 6100 DSL modem operating in bridge mode. The 4400 is obtaining the WAN address from Verizon(DSL) and that is also where I have my PPOE info entered to obtain the internet connection.
Cisco :: Reload 1941 Router When Ping Test Fails
Apr 9, 2012I am trying to create a Script to reload my cisco 1941 router when a ping test has failed.I am using IP SLA to ping and tracking snmp oid. What I want to do is to stop the router from reloading after 4 times if the ping test is still failing . But when the ping are successful again to restart the applet. I have the reload configured but cannot figure out how to do the rest. [code]
View 1 Replies View RelatedCisco Infrastructure :: HWIC-2FE Fails To Pass Ping Packets Greater Than 449 In Slots 0 Or 1
Apr 9, 2013When we install an HWIC-2FE card in slot 0 or slot 1 of a 3845, the interface fails to pass any ping packet greater in size than 449 bytes. It works fine up until that limit is reached, but then fails completely on a larger size packet. If we move to slot 3 or slot 4 on the 3845, the card works just fine! I have looked through the cisco official bug tracker for HWIC-2FE, but could not find a similar symptom listed. We're running advanced ip services 12.4(24)T7 code on the routers. Any software fix or if this is a platform problem with the 3800 series.
View 3 Replies View RelatedDell Inspiron 1545 Laptop IP Gateway Ping Test Failed
Mar 30, 2011I have a Dell inspiron 1545 laptop, which will not connect to my BT homehub, I know it is not the hub as can connect with my old PC. I ran a connections diagnostics test and it failed at IP Gateway ping.
View 8 Replies View RelatedLinksys Wireless Router :: WRT300N - Slow Speed And Low Ping Test?
Aug 18, 2007I have installed a WRT300N on to a new machine and the connection speed reads as 1 Mbps (not 100 but 1 ). I did a ping test and the results are
View 2 Replies View RelatedLinksys Wireless Router :: Can WRT54GL Pass 50mb Through To The Computer On Wired Connection?
Apr 12, 2013In our area Comcast has increased the internet speed to 50mb. I have a six year old WRT54GL. Can this router pass 50mb through to the computer on a wired connection?
View 5 Replies View RelatedLinksys Cable / DSL :: WAG160N-AU LAN Computer Cannot Ping Computer
Oct 8, 2008I just got a WAG160N-au, I run the installation disk, follow the procedures. I got the internet connection.
View 9 Replies View RelatedD-Link DIR-655 :: Upload Test Error Test With Speednet
May 3, 2011Question re: DIR-655; Hardware ver A4; Firmware version 1.32NA
During bandwidth tests to several sites (principally speedtest.net) I get ping times of 10-11 ms, download speeds of 12+ to 17+ mbps but failure on upload tests using my DIR-655.
When I bypass the 655 and test directly with my cable modem, all (including upload) tests work reliably and consistently.
I have swapped the two ethernet cables involved as well as replacing both with new cables but the results are the same (uploads fail with 655 and work without it)
I have seen several postings over the the last year with this same problem but have never seen any comment from D-Link, or a solution from any reader.
Not that it should have any bearing, but I have TA785GE-128M motherboard and am running Windows 7 (patch current) on COMCAST
is this problem acknowledged by D-Link and is there a solution?
D-Link DIR-601 :: Can't Pass Internet
Dec 8, 2011I just bought a DIR-601. It comes with an installation process on CD.The process fails at the point where I make the connection from my DSL modem to the DIR-601. The installation program reports that there is no internet connection. (Note that to get this far in the installation process the installation program has already tested for a valid internet connection before the DIR-601 is inserted into the chain)Although the LED on the front of the DIR-601 indicates it is getting an internet connection from the DSL modem, it does not pass it on to my PC (already connected to the DIR-601). My PC reports "no internet access".
View 8 Replies View RelatedCisco Firewall :: Pass Internet With ASA 5505?
Apr 1, 2013I have not been having much success configuring my 5505 for Internet access, and I'm sure there are a few small things I'm missing. At times I believe I got it to the point where I could ping, but still not pass through the Internet traffic. At this point, I reset the 5505 and only changed a couple of settings. I have an external range with these characteristics: Network Address 67.139.113.16 (.17 is Gateway), SM: 255.255.255.248, available IP: 67.139.113.218 The external connection is through a T1 modem, and when I put those settings in my laptop, I can access just fine. When I went through the startup wizard in the ADSM, I maded the internal interface 10.209.0.3, subnet mask: 255.255.255.0 I selected PAT in the Wizard, but don't know if I should have, or if the NAT rules I tried to put in are fine. Eventually I want to add a Site to Site VPN to the rest of the 10.0.0.0 network, but I can't even pass the Internet through to the inside. Also, this will eventually be behind another hosted firewall, so I'm not worried about restricting access, even currently. However, I suspect the problem is that traffic is being blocked with the NAT rules or Access rules.I wish I could just disable those inherent deny rules Outside of pings to 10.209.0.3, all pings come back as request timed out.
Config:
: Saved
:
ASA Version 8.2(5)
!
[Code].....
Xbox Won't Connect To Internet Via 360 Test
Aug 11, 2012I've recently purchased a new modem and router made by net gear I've been able to connect to the internet via laptop, cell phone, etc. but my real problem is that my Xbox will not connect through the net work test when I physically do it myself but if my Xbox is off and I reset the modem /router and then turn on the Xbox it connects me but doesn't allow me to play any games or talk to friends, so back to my first problem I test the internet using the Xbox, it connects to the network but not to internet and trows an error reset modem/router 30sec. ICMP error or MTU error I've browsed online for solutions but none are successful I've changed router settings bought an Ethernet cord bought a second more powerful router from net gear nothing is working, any ideas?
View 1 Replies View RelatedCisco WAN :: ASA5505 Basic Configuration / No Internet Pass-through At All
Apr 8, 2012I teach in a High School and we've got about a 300 node MS Windows Network. Two MS2003 File Servers act as my DNS/WINS/DHCP servers. We have been using a WATCHGUARD FIREBOX III to act as the router/gateway between the outside external address and my internal (10.0.0.1) gateway address. All p.c's inside the network are routed to one of the Servers (10.0.0.2 or 10.0.0.4) for DNS/WINS/DHCP addressing. The servers point to 10.0.0.1 for gateway.
We are trying to replace the Watchguard Firebox with a CISCO ASA 5505 (eventually we'd like to implement VPN). When I connect the CISCO ASA, I get no internet passthrough at all.
Cisco VPN :: 2811 - SSL VPN Services / Cannot Pass Traffic To Internet
Jan 17, 2013[OK] Site to Site IPSec + GRE = success, no problems.
[OK] IPSec remote access = success, no problems.
[NO] SSL VPN = remote users can successfully connect to all internal systems. Cannot pass traffic to the Internet.
Hardware:
Cisco 2811, Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(22)T5, RELEASE SOFTWARE (fc3) . Software: Cisco Any Connect Secure Mobility Version 3.1.01065
Single hub router terminating IPSec+GRE site to site, IPSec remote access, and SSLVPN remote access VPN services. All services currently configured and running successfully with the exception of the SSLVPN service. Remote users can initiate and successfully establish SSL VPN sessions. While established, connectivity to all internal systems/resources are successful. Only when the remote access client tries to connect to "Outside" Internet resources does traffic not pass successfully. Troubleshooting has pointed to a NAT related issue (I believe).
When connecting from a remote access workstation, utilizing IPSec remote access client (built-in Cisco IPSec client from Mac OS), the session establishes and the client works flawlessly. Examining the Cisco 2811 router, you see the /32 host route from the remote access session get installed, and you see the corresponding NAT translation entries created when the client accesses outside (Internet) resources. Appropriate configuration to implement "hair pinning" have been included to handle the in and right back out (with NAT translation) needed for remote clients to access the Internet.
Configured the 2811 for SSL VPN, and remote access clients can successfully connect and access all internal network resources. Examining the Cisco 2811, the /32 host route for the remote access client is installed, pointing to SSLVPN-VIF0 interface with a next hop of 0.0.0.0 When checking the NAT translation table, there are NO entries for the remote access client address created which leads me to believe the hair pinning/NAT function is not being invoked for SSLVPN clients.
Originally, the IPSec remote access VPN local pool was 10.0.100.0 /24. To keep from having to adjust the existing NAT translation, PBR Route-MAP for the hair pinning function - I took the 10.0.100./24 and broke it into a pair of /25 networks. Bottom half for the IPSec remote access VPN pool (10.0.100.0 /25); upper half for the SSL VPN pool (10.0.100.128 /25). By utilizing SSL VPN, is the traffic somehow bypassing the DIALER1 interface where both the crypto map (and more importantly: IP NAT OUTSIDE, and PBR configuration for the hair pinning function)? I cant explain why NAT translation entries are not being created for SSLVPN client sessions.
Cisco 2811 Configuration has been included. IPSec & SSL VPN Remote Access Sessions Captures (performed from same remote client) have been included.
Cisco Switching/Routing :: 4.2.2 Unable To Ping 1 Internet Site From Edge Router Able To Ping
Jan 18, 2013From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies View RelatedHome Network :: Internet Speed Test To Get 8 Mb Again
Jul 28, 2011I have a small network of around 5 PCs,I have 8MB shared connection from ISP,so when I run speed test check from one of my PC it returns around 1.76 Mb download and 0.07 Mb Upload Speed,if I connect one of the PC directly to modem and run the test again so can I get 8MB of speed?
View 17 Replies View Related802.11 G Router Of 54mbps - Test Internet Speed To See If Able To Get N?
Feb 12, 2012I currently have a 802.11 G router of 54mbps (its claims its a super G 108 mbps tough). My notebooks have 802.11 N built in. Im thinking of upgrading my router to a 802.11 N 300mbps.However, I know that this may be irrelevant unless I have a internet conection that can achieve such speeds. So how do I test my internet speed to see if G is bottlenecking?
View 4 Replies View RelatedWay To Configure Fortigate 200B Firewall In Web Base Using Pass Internet
Nov 9, 2011how to configure Fortigate 200B firewall in web base using pass internet through Cisco 800 router.
View 1 Replies View RelatedPing Computer In Another Domain?
Nov 24, 2011i need to know when a computer shutdown. Is a windows xp. Is in another domain. I cant use VPN.somebody knows a software that alert me (example: by email)?
View 2 Replies View RelatedWireless :: When Run Tests For Wifi Card The Internet Ip Test Fails
Dec 28, 2011I am trying to connect to my wifi network at my home. I have a Dell Wireless 1397 WLAN Card. I am using an Inspiron 1545 and operating Windows 7.My Router is a Linksys WRT54G. I looked through some old posts and this shows the results of IP Config test I ran:Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.Windows IP Configuration
Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : earthlink.net
[Code].....
Linksys Wireless Router :: Internet Speed Test EA6500
Feb 18, 2013I've a problem with the internet speed of my ADSL line(20Mega). Now I've the following components: D-link DSL-320 B (modem)+Cisco Linksys EA6500. If I start a Speed test the result its only 4M in download, while i remove the router and i connect my Pc directly to modem, the speed test results its 13-14M.
View 3 Replies View RelatedServers :: IP 169.254.0.1 Not Detected By Ping On Computer
Sep 22, 2012Hard Drive (Gembird not detected on My PC
View 3 Replies View Related