Is it at all possible to connect a client computer to an Active Directory via the Internet?
If so, would you change the client's DNS server to the remote IP, and then connect?
i need to know if i can integrate Single Sign On to my Cisco VPN Client v.5 with my Active Directory which run on windows 2008
View 2 Replies View Relatedit is possible to create a Windows Active Directory group of users which I can use to permit access through the ASA (5520) firewall? I only can find vpn authentication with Radius but nog specific information about granting AD groups internet access via the ASA.
View 1 Replies View Relatedit is possible to create a Windows Active Directory group of users which I can use to permit access through the ASA (5520) firewall? I only can find vpn authentication with Radius but nog specific information about granting AD groups internet access via the ASA.
View 1 Replies View RelatedI have installed ACS 5.2 and configured it to join the Company's Domain as an External database with Active directory 2008. I'm facing a problem that the user once authenticated using it's active directory account it's cached in the ACS and take a while for the ACS to clear this username. For example, if user TEST authenticates and then we removed this user from the AD and then tried again; it authenticates although this users is removed from the AD !!! same thing happens when we change the user group on the AD, it takes a while for the ACS to clear the old user attributes and get the new ones from the AD.
it there an aging time for this caching mechanism, or can i clear the dynamic users manually just like in ACS 4.X ?
I am trying to set up a small domain for my business. I just purchased a Windows 2008 server and would like to use it as my domain controller.Also, I just had a new ATT DSL line put in. It came with a 2Wire modem/4-port router/wireless router device, therefore the modem can handle DHCP. The line has a static IP address as well so that I can eventually use my own exchange server and web server.I have tried 2 different configurations and couldn't get either to work) I tried to put the router into Bridged Mode and use DHCP server on my server using a PPPoe connection to connect to the Internet. I was confused as to what my static IP address and default gateway of my server should be.2) Then I tried to turn DHCP server off on the server and routing back on the modem/router. This didn't work either.What method would you recommend and why? Also I have some additional questions on each method.
Method 1)
* What is the static IP address of the server. Is it in the 192.168.1.x address or the static IP assigned to my account?
* Do I need a second Nic Card And Router to connect to the rest of my network or can I use the router provide
* What would the Static IP addresses of the additional PC be. Do I need more than 1 static IP from AT&T Method 2)
* Will this allow me to use all internal IP addresses on my machines and use port forwarding if I want a specific box to be a web server or exchange server.
I know that when you create a user account in active directory, the user's computer is also added to active directory. However, in what circumstance would you add a computer to active directory in which there are no user accounts created, or used ?For instance, my Linksys wrt54g router, on the main configuration tab has a space to name the router, which is appropriate called, "Linksys", and it has space to enter it's domain name, which if I named it, I guess it would be. LinksysRouter.**.local.Why add a router to an active directory domain ?Why add any other computer to an active directory domain with no users associated with it ?
View 11 Replies View RelatedI have 1 server where i enabled dhcp server and active directory on it . I still have to install something like ISA server on it as isa doesnt support 2008 r2. point me out on the networking , like how should i connect the clients to the server. And how the wireless router and switch should be connected to the server?
View 1 Replies View RelatedI've got a fully working active directory with mandatory profiles. I'm looking into adding MS Office 2007. I have the disk and everything, but I'm wondering how to go about installing it. Must I go around each workstation installing it?
View 1 Replies View RelatedI've got this problem with our Operations Manager's laptop not letting him log in once he is offsite(at home). We use an Active Directory server here for all out workstations to log on to the domain but once he is offsite he cannot log in because the laptop obviously cannot find the sever to authorize the user. For now I just have him logging in locally to his laptop and not to the domain when he is offsite but this creates a problem; it makes two users/desktops for him, one user.domain and user.local. Is there a way to tell the machine locally that his username is authorized to let him log onto the domain account though it cannot connect to the domain server?
View 3 Replies View RelatedHaving problems configuring an SR520 to support SSL VPN with Active Directory authentication. I set up the domain and a user in the SR520. and get the login prompt remotely but when attempting to login using the active directory account i get a login error. I can login fine using local authentication.
View 5 Replies View RelatedI am not sure why but when I try to connect with my IPSEC VPN client, authentications are failing. The ldap test passes on the ASA but when I try to login, the VPN client gives me authentication failure even though debugs show authentication was successful.User 'test1' should be able to authenticate based on group membership.User 'test2' shouldn't be able to.I already removed the attribute-map to see if that was the problem but I am still failing authentication.
View 9 Replies View RelatedCurrently We have several Active Directory Domain at several Technical High Schools. These are used by us as a it educational unit(s). The Tech School System's IT Department has a fiber wan between the schools that allows communication between these units. We wanted to interconnect the unit's Active Directory's with Trusts or by combining them into one forest. However I am wondering How much bandwidth that alone would require? There make be some file access between units but not on a daily basis since the units are separate from one another. How much bandwidth do you think this would require?
View 5 Replies View RelatedI am adding a site in another time zone but keeping the same active directory and domain. the time zone issue if there are no servers in the other time zone?
View 1 Replies View RelatedI am receiving a RADIUS authentication failure stating user must change password; however, password has been changed in AD and is not requiring change password any longer on the AD side.
Is there a cache on the ACS that needs to be cleared? AD connection from ACS to domain is fine. All other accounts authenticate.
It appears that if a user lets their account expire is when this happens. Account has been reenabled in AD and password has been changed. Still will not authenticate via ACS.
I'm attempting to integrate an acs 5v into the domain through the gui. The connection will establish, and the status will read 'connected', just as it lists the domain I've submitted. However, I can't seem to find anything listed under the directory groups, and when I run a connection test, I simply get 'Global Catalogue port status error.' Eventually, I'd like to configure this as a radius server.
View 1 Replies View Relatedquestion 1. in the typical active directory environment and doing wireless/wired 802.1x authentication on endpoints, should ACS join as a domain computer?
question 2. for the endpoint (domain computer) join the domain, in this case is the endpoint will trust the ACS ( also domain computer) ?
question 3. what if there's a GPO policy to install the rootCA certificate toward the endpoints. In this case, ACS should issue the CSR and let the domain CA to signed as the identity certificate? Am i correct?
I am working with ACS 5.2 and using Radius authentication for vpn client.
The authentication method used is Active Directory in an Windows enviroment with multiple domains in the same forest.
My problem occurs when i change a user from one group to another in Active Directory. After that i receive the following message when try to connect:
15039 Selected Authorization Profile is DenyAccess
The message is because match the default policy. Another user in the same AD group works fine. All domain in the forest have trust relation each other. I am using universal groups to include users from all domain belongs this forest.
I recently bought a Cisco WLC 2500. I want to configure a WLAN with Active directory authentication.How I can do this?
View 4 Replies View Relatedi need a documentation or a procedure to how make integration LMS 3.2 with microsoft active directory to make usernames of devices appear in end hosts reports.
View 2 Replies View RelatedA customer uses Active Directory where some group names contain special characters (ç ~ '^). The Cisco ACS 5.2 is presenting the warnings: "Not all Active Directory user groups are retrieved successfully. One or more of thegroup's canonical name was not retrieved "(Category CSC Oacs_ Identity_ Stores_Diagnostics; code 24457).
What are the results of these warnings to the customer's network? Slow? Loss of access?
configure the Cisco ACS to authenticate the users from MS Active Directory. Cisco Acs = 4.2.1(15)Currently, i have multiple users configured as local databse. but now i want to authenticate with the domain users.
View 11 Replies View RelatedI have installed 4 unit Cisco Aironet 1250 acting as Autonomous AP each. I want to integrate these AP to Windows Active Directory for authentication level.
When I read configuration guide on Cisco Aironet, they must be authenticated via RADIUS server.
Is it possible that these AP directly authenticated to Active Directory via LDAP protocol?
I have been rolling out new IP Phones that use extension mobility and the biggest issue Im finding is the need to log-in every day, People t like change and they hate the fact that they have to login every day.I have been to the people at the top and gave them the options of remembering the last user logged so users just need to enter their pin or have EM not log users out at all… both got rejected.
View 2 Replies View Relateduser can't login into domain with right credentials in active directory
View 6 Replies View RelatedI have a 5515 ASA that has the webVPN configured on it and it is using active directory to authenticate. The client would like to set up groups in active directory and restrict access to those groups when they are connected to the webVPN. For example, they have a group in active directory that they only want to access their "web" interface. What is the best way to configure this on the asa?
View 2 Replies View RelatedI have a WAP4410n which I'd like to authenticate users against our corporate active directory. I would like to know how to achieve this - whether we require a dedicated RADIUS server, whether AD has a RADIUS engine which can be used, etc. Also, what would the pros / cons be of this setup versus using a WPA2 password?
View 2 Replies View RelatedRather than maintaining local accounts is it possible to authenticate admins against AD? I'm talking about administrators of the ACS server itself to be clear.
View 2 Replies View RelatedWe are trying to manage our Cisco ASA 5520 (8.2.5) SSL clients through Active Directory(ldap).
Currently the SSL VPN tunnel is up and all users are able to connect being authenticated by AD. but Group-policy to AD groups are not working. all the domain users are able to go to all the group policies .
I need to give access only to their respective Group policy in ASA. Following are the available groups and GP.
Code...
I've successfully integrated ACS 5.3 with Active Directory for 802.1x implementation. Now i want to cache Active Directory users in ACS so that the user request from ACS does not go to AD every time.
After a certain time period the ACS database gets sync with AD.
I can add a ACS 5.1 to an Active Directory without using the administrator account, I have a domain administrator account by another name. I can use this account to include the ACS domain.
I have a account domain admin but when i try to add the ACS to AD have this message "can not resolve network address"
The DNS and network connectivity its OK
if someane has a good guide for 802.1X with ACS 5.2 with Active Directory.
View 1 Replies View RelatedWe are still running ACS 4.1 on Window 2003 server. We recently upgraded AD to 2008 although the domain and forest functional level are still 2003. After AD upgrade we now unable to authenticate via ACS Windows Database.
View 13 Replies View Related