Process To Connect Two ADSL Routers?
Feb 23, 2012Tell me the process to connect TWO ADSL Router
View 1 Replies
ADVERTISEMENT
Broadband :: Connect 2 ADSL Routers On 1 BT Line?
Feb 19, 2011Our church has 1 phone line, we run BTBusiness Broadband at one of the building where we have a couple of charities based. We have the phone line connected to an extension at the other end (where the Church is) >80m away. Any way of running a second concurrent router on the extension so I can set up an office with a VOIP number, pC's printers etc there too? We use Devolo ethernet over mains and wireless for the main building, but the church itself is on a completely seperate mains power supply so I can't use that. I could run 100m Cat 5 and locate a switch on that, but any way of achieving something similar over the phone cable which is already in place.
View 2 Replies View RelatedRouters / Switches :: Connect 2 Adsl Devices Together?
Mar 1, 2011A Telindus 1421 SHDSL Router and a Sagem F@st 1500WG wireless adsl router.The question is: Can i connect this two devices directly over the adsl port and share networks on each side of each of the devices?
View 3 Replies View RelatedRouters / Switches :: To Connect ADSL Direct To Computer
Dec 2, 2012I have CentOS and the application I am running does not listen on 192.168.1.5 (Private IP address). Right now I have connected using bridge mode and I can see in my network configuration-> ppp and eth0. PPP has public IP and eth0 has private IP. Is there any way that I can get public ip assigned to eth0? I do not have Static IP, I want to use the public dynamic IP assigned by my ISP to use in eth0 interface.
View 2 Replies View RelatedRouters / Switches :: How To Connect ADSL And 3G Router On Network
Aug 7, 2012I have one ADSL router that I have configured Port Forwarding on it, but the internet is very slow. I also have another 3G router and I want to use it for internet because it is much faster, but it cannot do Port Forwarding. How can I connect this two routers in one network such that ADSL router is for Port Forwarding only and 3G router is for internet only?
View 1 Replies View RelatedLinksys Cable / DSL :: WAG120 - Connect Two ADSL Routers?
Feb 14, 2012I was using Linksys ADSL router ( WAG120) as modem router. Recently I bought new Linksys x3000 and installed a modem router in place of WAG120. Now i would like to connect the both routers to get the signals in first floor of my house.
View 9 Replies View RelatedCisco Routers :: Total Failure To Get SR520-ADSL-K9 To Connect To ISP
Dec 15, 2011We've (an independent school) just bought an SR520 with a view to replacing one of our Draytek 2820s. We need to set up some site-to-site VPN with NAT and the Drayteks won't do it.
I've been trying to configure the SR520 in just the most basic fashion using CCA (3.1) and the CLI but with no success. I can't get a PPP connection with our ISP.
I've tried following the instructions in the software config pdf and also tried replicating the various 'running configs' reported in other posts in this forum to allow connection to a UK ISP, with no success. I don't know how many times I've reset the poor thing to factory defaults.
I have to say that I'm dismayed at how flaky the CCA appears to be. Many of the things I've tried with it simply don't work and often end up in it hanging. Close to useless in my view.
So instead I've tried to use the CLI which seems a lot more solid but is somewhat impenetrable and there's precious little by way of supporting explanation.
Routers / Switches :: Connect Win98 To ADSl Modem Over The Network Switch?
Apr 19, 2012Have one switch and network.PC number one have win98 and network adapter and connected to the switch.PC number two have winXP and network adapter and connected to the switch same as win98.Network works on win98 and winxp they see each other.internet working on winxp but dont work on win98
View 2 Replies View RelatedCisco Switching/Routing :: 4506E Any Free CPU Process Monitoring Tools To Identify Which Process Is Spiking
Oct 9, 2012I have two core switches - 4506E, and i noticed there are frequent cpu spikes on both of the cores switches. As its spikes intermitendly i couldnt able to anlyze the issue. I need inputs on the following,
1) Is there any Free CPU process monitoring tools to identify which process is spiking ?
2) Troubleshooting techniques to identify the issue.
Cisco Routers :: RV 042 Is Not Doing Any Redundancy Process
Feb 21, 2013I have problems with the RV042 router. Currently I have two Internet service is the first DSL service and the other is through cable. The problem is because the router is not doing the redundancy process. For example if DSL service fails, the cable internet service does not come automatically. You have to disconnect and connect manually to maintain the connection to the Internet. Should not the router do this automatically without intervention?
View 1 Replies View RelatedCisco Routers :: SA540 / Unable To Process Data Received From Secure Gateway
Dec 26, 2011Is Anyconnect supported for SA540 I have installed in on my android phone however I keep getting error "Unable to process data received from secure gateway" when trying to connect. If anyconnect is supported on SA540 how do I get it working?
View 1 Replies View RelatedInstalling 2 Adsl Routers On One Telephone Line
Mar 28, 2011Can I install 2 ADSL routers on one telephone line with SKY. If I can does this mean that if sky give me 20mb connection, I can get two lots of 20mb using the two routers.
View 2 Replies View RelatedCisco Routers :: SRP 527w - ADSL Disconnections
May 12, 2011at our office we've recently upgrade from a old consumer-grade linksys wag200g modem/router/ap to the Cisco SRP527w. The Cisco is suffering from very frequent ADSL disconnections. These disconnections happens when there is some traffic to the internet and they seem to don't affect the LAN routing: on the weekends there are no disconnections at all while during the working hours there may be disconnections every FEW MINUTES making this router unusable. Often these disconnections force us to do a full reboot of the router.
Firmare version is SRP520W-1.1.19, the latest. ADSL line is a 6Mbps/640kbps. Noise margin is about 11dB for downstream and 20dB for upstream.
No voice line is used and therefore they are both disabled. 2 wireless network are active. The old linksys was (and is) working correctly, no adsl disconnections at all. Never.
Belkin Routers :: How To Change Adsl Modulation On AC1200
Feb 11, 2013I just bought the AC1200, but looks need to change the modulation for adsl2+.
View 3 Replies View RelatedCisco Routers :: How To Setup RV082 Behind A ADSL Router
Feb 21, 2013I have a RV082 VPN Router. But my internet connection is ADSL brodband. How can i connect and setup a VPN connection to other RV082.
View 1 Replies View RelatedCisco WAN :: ADSL Firmware With 877 And 1801 Non Modular Routers
Mar 13, 2011I have multiple customers with either 877 / 1801 routers with dsl issues, we keep dropping sync , get slow speeds etc,
I have already updated to firmware 4.018, in some cases it has resolved the issue in others it has not, BT say their lines are ok, but still i keep getting issues.
Cisco Infrastructure :: ADSL Disconnects On 800 Series Routers
Mar 21, 2012We have deployed a number of 800 series routers for some of our clients and have found that in many cases they seem to disconnect at an excessive rate. When I connected to the console of one the other day I could see that the virtual-interface for the ADSL connection was down, but not the ATM or DSL interface. If I disconnected the cable and reconnected the virtual-circuit came back up momentarily before disconnecting within a minute.
If I switched off the router for a few minutes and powered it back on it would usually remain up for a few hours. I reconfigured the router again using exactly the same config and it seemed to stay up for quite long periods for 4 or 5 days before reverting to type. [code]
Cisco Routers :: SRP547W Dropping ADSL Every Minute
Feb 22, 2012We installed one of these devices as our gateway a couple of weeks ago, flashed the firmware to 1.2.4(003) and it worked perfectly until this morning where it keeps resetting the ADSL every minute and losing the web interface to the unit.
The log endlessly reports this:
Feb 24 11:26:00 SRP547W cron.info cron[8779]: (root) CMD (/sbin/check_gn)
Feb 24 11:26:00 SRP547W cron.info cron[8781]: (root) CMD (/sbin/check_ps)
[Code].....
Cisco WAN :: Connecting ADSL Line On HWIC-ADSL On Router 2901?
Aug 24, 2012i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies View RelatedNetgear DG834GT - 192.168.0.1 - Connecting Two Routers With Separate ADSL Connections
Aug 9, 2011how to connect 2 routers that both have an ADSL connection. When attempting this the Belkin router will lose the ADSL connection after a random amount of time.
View 5 Replies View RelatedBelkin Routers :: How To Change Adsl Modulation On N600 Modem
Nov 9, 2012I am wanting to force the n600 to g.dmt for a more stable connection. cannot work out how to do it. am force into using old modem as far from the dslam and forcing adsl 1 improves performance.
View 4 Replies View RelatedCisco Switching/Routing :: Load Balance Between 3 877 ADSL Routers
Apr 25, 2012I have 3 877 ADSL routers for internet connectivity. I recently installed a FW behind them and would like to use the Ciscos as load balance in order to get better utilization from my 3 internet links.
1) the 3 routers are on DHCP from the ISP on the WAN side.
2) the 3 ciscos are on the same class C subnet on the LAN side: 10.201.1.252, 10.201.1.253 and 10.201.1.254
Cisco Routers :: RV120W Rebooting Itself When WAN (ADSL Modem) Breaks Away
Aug 16, 2011I have a RV120W that reboots itself when the WAN (ADSL modem) breaks away. With an old D-Link low end router, reconnecting after a failure is completed after 5 seconds and nobody cares, but the RV rebooting takes almost 2 minutes which is actually noticed...I also have some trouble getting VPN running, QuickVPN as well as normal IPsec, using either Shrewsoft or Greenbow as clients. get this router running with 3rd party VPN clients?
View 1 Replies View RelatedConnect Dir 615 With Adsl Modem?
Jan 27, 2011recently i got a dlink dir 615 router from a friend. i'm using adsl modem now. i want to connect the modem to the router so that i have a wireless at home for my laptop and iphone. i have follow the step in the router manual but it did not work. i just cannot conect to the router page through the 192.168.0.1 i am using windows vista home basic.
View 15 Replies View RelatedCisco Routers :: SRP547W - Can't Ping External Side Of ADSL Interface
Mar 2, 2013I have installed a couple of SRP547W's and can't ping the external side of the ADSL interface.
Is there an option to turn on "respond to ping" and also are you able to forward to a internal IP?
Cisco Routers :: Wag120n How ADSL Modem Handle Incoming Sip Calls
Feb 14, 2013I have a Cisco wag120n adsl modem. I am setup with a SIP provider, so all my incoming and outgoing calls use SIP.So my question is, how does my ADSL modem handle incoming SIP calls,e.g the SIP call comes in and reaches my adsl modem. Then, how does the modem find the actual port that has my ATA adaptor (analog phone) or CME router attached ? I know port forwarding would handle this, but I am not actually using any configured port forwarding rules.
View 1 Replies View RelatedBelkin Routers :: N150 Wireless Modem Router ADSL Slot?
Dec 17, 2012I bought "Belkin N150 Wireless Modem Router" and while installing noticed that the ADSL slot is too short that does not fit the LAN chord, instead fits the telephone chord. How do I fit the LAN chord fit in the ADSL slot? Any alternatives? My ISP comes with a LAN chord and is connected directly to my PC.
View 3 Replies View RelatedCisco Routers :: SRP527W Act As L2TP Tunnel Initiator Over ADSL PPPoE Interface
Jan 29, 2013We are using SRP527 routers with PPPoE ADSL connections. From the SRP527 we create an IPSec tunnel to our core routers (Cisco ASR). We are wanting to change the IPSec tunnels to L2TP, and I need to know if this can be done from the SRP527. I cannot find any L2TP configuration options in the setup options.Can the SRP527W act as an L2TP tunnel initiator over the ADSL PPPoE interface?
View 1 Replies View RelatedConnect A Wireless Modem To Adsl For Wifi?
Jan 15, 2013I wanna Know That I hab a nokia siemens SL2_141 modem which is not in use...beacause I dont have anymore BSNL connection. Now I am using A Wireless Modem of MTS. Recently I have Buyed New Phone I wanna Use wifi...
HOw Can I connect Internet of my Wireless Modem to The Wifi of nokia siemens SL2_141 Modem.I have Attached A photo So that U ppl Understand properly.
Linksys Cable / DSL :: X3000 Cannot Connect To ADSL
Dec 12, 2011I just bought a Linksys X3000 to work with my ADSL connection (provider is Singtel from Singapore). I managed to use Cisco connection application to logon and setup the router OK, yesterday. I even connected my PC to the router by LAN, and also a few devices wirelessly.At the end of the day, I switched off everything... but next morning, when I booted up the router, I found that all my devices cannot access internet. Upon checking the server (192.168.1.1), I found that it does not have a IP from Singtel, although on the router the internet symbol (globe sign) is lighted up.I rebooted the router twice, getting the same results (note: I waited for a long time each time, until the globe was lighted up).I disconnected the X3000, and reconnected my Netgear DGN2000. It worked (and retrieved an IP address from Singtel). I then disconnected the Netgear and reconnected X3000. To my surprise, this time X3000 got the IP address and then internet is working again.
View 9 Replies View RelatedCisco WAN :: 2801 - Connect Two ADSL Links On It?
Feb 2, 2012I have a cisco 2801 router and I want to connect two ADSL links on it and balance the load but not that kind of IOS that team would need
View 2 Replies View RelatedZoom Adsl X6 Model 5590 - Internet Not Working After Attempting To Update Routers Firmware
Jun 21, 2011I have a Zoom adsl x6 model 5590 wireless router. I recently tried to update its firmware by following the instructions from the manufacturers site. Everything seemed to go correctly, but I am now unable to connect to the internet or my routers http address. My router now has a red power light along with a solid green light for the wlan and dsl.
View 2 Replies View RelatedServers :: How To Connect A Adsl Modem To A Computer Network
Jun 19, 2011how to connect a adsl modem to a computer network using a switch with a server.I have a network with a server and about ten clients computers all connected through a switch, the server has an IP 192.168.1.1 as its gateway. I want to connect adsl modem to the switch so that all the computers can have access to the net, but the adsl too has 192.168.1.1 as its IP.
View 1 Replies View Related