I would like to be able to allow a specific client to only associate at 6mbit/s -is this possible using the wlc controller 5508? Another option would be to limit a whole w lan ssid to 6mbit/s but i can't find a way to do that either.
Other w lan ssid's on the same access points/controller need full data rates, so i guess i can't use the RF-profiling for this.
Is it possible to enable an absolute value rate limit using QOS on a HP ProCurve 5406 switch for a particular IP range on a specific port? Is there a way to configure our HP 5406 with an absolute rate limit on "WAN" port for that server's IP range? I would like to limit it to only being capable of sending 1Mbps worth of traffic over the head end at once.Everything in the documentation points towards priority queues, which as far as I can tell, isn't really what I want.Baring accomplishing this goal using rate limiting is there a better way to prevent our services from accidentally saturating this connection?i thimkong about somthing like that:
class ipv4 rate-limit-port-A1 match ip 10.136.0.0/16 any exit policy qos port-a1-ratelimit class servers-to-be-slowed action rate-limit kbps 1000 exit interface A1 service-policy port-a1-ratelimit inI'm not sure about this.
I bought this router to temporarily replace my firewall while I wait for it to be replaced. We have a training center that when running full tilt, we probably have 50 devices trying to get on the internet.
I have a f9k1113 V1 or AC 1200 wireless router. I opened RDP - remote desktop to my home pc. Everytime i try to connect from the internet to my home pc the router reboots. I never get connected. It seems when the router sees that type of traffic it reboots.
add VDSL2 (Fibre broadband) support in a future firmware update to the AC1200 Modem Router - F9J1106v1? If it's not possible to have a single modem firmware that supports both ADSL and VDSL, any separate downloads for the customer to choose depending on which type of broadband connection they have?I am in the UK, my ISP is Plusnet. They use BT Openreach infrastructure. The currently supply the same rebranded Netgear router to both their ADSL and VDSL (Fibre) customers. The only difference being the VDSL modem has custom firmware flashed on it.
Access Control on an ac1200 does not seem to flexible enough to include hours from say 8pm - 6am. On my old Linksys I would simply have multiple entries for the same MAC address but this does not seem possible.
My Comcast cable modem does not have a 2nd port needed to connect my Belkin AC1200 wireless router. Is there another way to configure this or are my options to either buy a new cable modem or try to upgrade it through Comcast?
I have two AC1200 routers? how do i connect one ac1200 to another ac1200. Only one should act as a DHCP server and broadcast wireless; the other should be simply just a hub (vs. me having to buy a separate hub). What are the correct settings and connections?
I have a Belkin AC1200 Router. It seems working properly re Internet/Wireless connections. When I connect a printer (Canon Pixma MP500) through the USB port the (USB) light doesn't turn on, nor the printer is appearing on the "available devices" (Belkin USB Print and Storage Center).
I use a router RV082 with load balancing. My problem is when I try to access a specific site, I get the error message that my IP address changes and I can not use 2 ip address. I want to specify an ip range to always use the same WAN port.
I have a Belkin N750 router which I purchased because the box said it had filtering options. I didn't realize that the filtering was only sites that Norton kept track of. There are certain adware sites I know about that I would like to filter. Possible with this router?
I would like to allow PING on RV042 from WAN side only from specific IP address, but when I set the rule, RV042 does not respond on WAN side, because Block WAN Request is Enabled.BUT! When I disable "Block WAN Requests", now any IP can ping my router from WAN side. Although I set access rule to Deny Ping from WAN side to anyone, it still responds.
I just got a new Thompson Cable Modem from MediaCom. The old Surfboard gave out. However, my Belkin F5D9230-4 will not retrieve a new IP address. When I hook my laptop to the cable modem, I do get an IP and I can surf the web. The Belkin admin page says Disconnected. I've got latest firmware. I've reset to factory standards. What else can I do to get my Belkin working again?
What do I do if I cannot access the setup address IE 184.108.40.206?I use my N750DB as a network booster at home. It runs via ethernet cable from the main router. I used to be able to get on no problem and now, I just can't. I have spent 2 days trying to sort my internet problems.
I have a n150 and it only allows private ip addresses for the lan setup. Is there anyway to assign a public address? I need to have the DHCP use a public range and I can't do that unless I can set the router to a public ip.
Within the Internet Access Policy section of the browser based utility, is it possible to limit access for a specific device (PC) to LAN only (not allow any traffic to external internet)? I see that you can block internet access for a specific machine, however I didn't know if this was inclusive of LAN as well.If not, is there another way to achieve this via the E3000 or should I be looking for a solution on the specific PC itself?
Need to limit the amount of bandwidth a specific VLAN can use on a 802.1q trunk port. Situation is that we have a pair of Catalyst 4506 switches which have 802.1q trunk ports into a Checkpoint Firewall, this in turn is connected to a managed WAN router (to which I can't apply a QoS policy).If the 4506 was routing the traffic it would be easy to setup a class-map to match the IP traffic and then QoS the traffic, but the VLAN in question is trunked directly into the firewall (no L3/IP presence on the 4506 next hop for all clients on this VLAN is the firewall).What I need to do is restrict any traffic from this specific VLAN to 10Mbps on the uplink to the Checkpoint Firewall so it cannot impact the onward WAN.
I have a Belkin N150 wireless router. I have enabled MAC Address Filtering as an added level of security. However; whenever I access the router, and if I check that page; the check mark for the option to enable the filter is always blank.
I have checked the option, clicked Apply Changes, and logged out of the router. i went back in this morning, to check the security logs. (Looking like someone is trying to jump on my network) I didn't see anything there, but when I checked MAC Address Filtering; there was no check mark indicating that the filter was turned on.
It took a while of troubleshooting since I've never ran into this problem with my wireless router before. But finally I figured out that my router will not assign the proper DNS server addresses when assigning through DHCP. I upgraded from 2.10.02 and still the same issue.
I have a cisco 2821 router where as a cisco 2960 switch with connect on router as a trunk & one user vlan . this is my WAN router all traffic are internal . i have 2MB data connectivity on my WAN side. i have to Give a specific Bandwith on my SAP traffice . like when SAP traffice will come they all time get around 50 % bandwidth of my channel. If SAP resuest are not comming then other traffice will get full bandwith .
My company has a peer to peer network of 10 personal computers without a server. Operating systems from Windows XP to Vista. I've recently installed a Cisco RV120W Wireless-N VPN Firewall. It's configured in DHCP Server Mode with printers/copiers that have static IPs below the DHCP range.
I'm having a problem with certain stations being used for personal networking, shopping, etc. during business hours. Consequently I would like to limit internet access on these stations. However, some internet access is required because of online database software that's an integral part of our business. I've been reading in the Administration Guide about URL Blocking. Would it be possible to give static IPs to certain stations and then limit their internet access to 1 or 2 specific websites?
FYI, I've read about the Trusted Domains and Blocked Keywords but cannot quite understand how to parley this into the solution I need.
configuring a switch or a router to limit the bandwidth for a specific user/IP when need it. Most of my remote offices are configured like this:
Users ------ 3560 switch ------- 2801 router -------- T1 to NOC -------- 7204 router with channelized DS3
I use Netflow Analyzer for high bandwidth usage alerts and can see the user's IP right away when someone is clogging our T1s. My goal is to be able to temporarily limit the bandwidth of the user taking over the T1. Whatever is best switch config or on the router.
On my cisco IOS 12.4 router,Can i make it so only lets say mac address 11:22:33:44:55:66 able to use ip address 10.10.10.2?I want this so that only this IP can configure servers, and so if the computer using it is turned off, any other device cannot use the IP address.