I have a f9k1113 V1 or AC 1200 wireless router. I opened RDP - remote desktop to my home pc. Everytime i try to connect from the internet to my home pc the router reboots. I never get connected. It seems when the router sees that type of traffic it reboots.
I bought this router to temporarily replace my firewall while I wait for it to be replaced. We have a training center that when running full tilt, we probably have 50 devices trying to get on the internet.
add VDSL2 (Fibre broadband) support in a future firmware update to the AC1200 Modem Router - F9J1106v1? If it's not possible to have a single modem firmware that supports both ADSL and VDSL, any separate downloads for the customer to choose depending on which type of broadband connection they have?I am in the UK, my ISP is Plusnet. They use BT Openreach infrastructure. The currently supply the same rebranded Netgear router to both their ADSL and VDSL (Fibre) customers. The only difference being the VDSL modem has custom firmware flashed on it.
Access Control on an ac1200 does not seem to flexible enough to include hours from say 8pm - 6am. On my old Linksys I would simply have multiple entries for the same MAC address but this does not seem possible.
My Comcast cable modem does not have a 2nd port needed to connect my Belkin AC1200 wireless router. Is there another way to configure this or are my options to either buy a new cable modem or try to upgrade it through Comcast?
I have two AC1200 routers? how do i connect one ac1200 to another ac1200. Only one should act as a DHCP server and broadcast wireless; the other should be simply just a hub (vs. me having to buy a separate hub). What are the correct settings and connections?
I have a Belkin AC1200 Router. It seems working properly re Internet/Wireless connections. When I connect a printer (Canon Pixma MP500) through the USB port the (USB) light doesn't turn on, nor the printer is appearing on the "available devices" (Belkin USB Print and Storage Center).
I have a N750 and I want to change the IP address through the browser. It is the standard 192.168.2.1 config. I change the IP to 192.168.15.x while hard wired and hit apply. The router reboots but still holds the same IP.
N+ requires constant reboots to maintain speed. When I reboot the router F5D8235-4 v3 it will run at top speed of 10mbps, after a day or two it slows to about 2mpbs. A reboot will speed it up again. I would prefer that it run fast all the time. Firmware 3.00.15
I have a Belkin G router F5D7230-4 (firmware version 8.01.07) and am trying to view stats on what is using our connection.We have a very low capacity, rural wireless broadband that our ISP tells us is maxed out all the time, even when we don't appear to be using any devices, so I'd like to view the traffic on our DHCP client list to see which device is using an excessive amount of bandwith and put a limit on its access.I don't see a statistics tab on the setup page, is there another place to look or does Belkin have an external program to do this?
I run a AirPort Extreme router. I have my F9K1106 range extender set up and working. works awesome. I get home from work the next day and the range extender seems to fall asleep , it won't pass any traffic. I power cycle it and its back up and running. this happens everyday no fail for a week now.
I've began having problems with the WRV210 where the router just reboots. Sometimes it may go for an hour or more then it slips into a series of reboots. The up time varies so I see no pattern. Contacted support they thought the device may have been defective so we did a RMA. Well guess what? The replacement arrived on Friday we put it in place and the same thing is happening. We are not using any of the VPN or VL options. Just simple PAT to a few internal machines for RDP access and an internal exchange server. The Qos is all disabled. It has the newest firmware which I have reflashed. I'm at a loss to explain the behavior but it doesn't appear to be isolated to a defective device.
I have an ongoing problem with my WRVS4400N router. It reboots on it's own when streaming video through a wireless connection (computer, xbox, roku, tv). Once I make a wired conection, it performs flawlessly. The firmware is up to date. I have read some reviews of this router on Amazon stating the same problem, but I expected it to be solved with firmware update. Unfortunately, this was not the case.
I recently purchased the RV220W to upgrade by good, but aging RV042. I'm running the most recent firmware (18.104.22.168 as of this writing) and have noticed this router reboots daily. I'm guessing it's locking up and rebooting as it occurs as different times of the day. Compared to the RV042, this was a bit of a pain to setup especially with regard to port forwarding. I'm hesitant to reset and start over again especially since this is brand new.
I have problem with RV120W router, device reboots very often ( up to 3-4 times during working day ), firmware is up to date ( 22.214.171.124 ), last week I decided to use "restore the factory defaults" unfortunately problem still exists.
Router is working in small office, there are 3 PC and 3 VOIP phones ( connected via LAN ) and 1-2 devices connected via wireless ( smartphones )
I've tried to view some logs but unfortunately no luck, can see some errors/warnings in dashboard ( see attached picture ) but cannot see more details ( log configuration wrong ? )
Additionally sometime I can see that CPU utilization is 100%
It reboots randomly every day and I got the following message in the log: [rv220w] System][FIREWALL] fwPPTPGenericRules.c: inet_aton failed I saw one internet that I can ask cisco for the Beta firmware 126.96.36.199 that fix the issues(Iactually use 188.8.131.52). Is it the solution? How can I obtain the beta firmware?
If your wireless indicator is flashing red when you discover the smurf, it can mean that someone has tried to logon with an incorrect password. this is not necessarily an attack, it could be someone you have allowed access too, who has forgotten the password? In this case entering the correct password will solve the problem.However putting your own MAC address into the filter will simply block your own machine.
I have the N600DB Wireless Router I am connected to the internet, but cannot open My Routers Homepage with http://router or http://192.168.2.1. How can I get to this page to reset the router settings? I also cannot connect any of my wireless devices to the network..
I have two matching N300 Belkin routers. The cable modem feeds into modem1 and modem1 feeds into modem2. I get a good wireless connection on modem1. Modem2 shows up on a wireless scan and it accepts the password. It however will not connect.
In my house...I have one router upstairs (Belkin F5D8236-4) and great signal upstairs...downstairs signal is not so swift and sometimes, I can't even get a signal. So I thought let me go purchase a router (router # 2) and set it up downstairs and see if that will improve the signal of my Belkin. The 2nd router I purchased is a Belkin N150 (I thought buy 2 Belkins...maybe they can communicate better?). What I need to know is how do I connect the Belkin N150, to my Belkin F5.. and just use it to strengthen my signal to my downstairs part of the house?
I see the switch to toggle the QOS on and off, but it is greyed out in on and will not allow me to switch. I would like to see if it solves the speed problem with my iPad. The newest firmware is installed in the router. I also tried changing other fields to see if it would unlock the quality of service field with no luck.
Lately I notice my router is very very slow. most of the time I cannot use my ipad or it takes too long and sometimes never finishes downloading a web site. I called Belkin support, and I was told that I need to update and configure, and to do that I have to pay more than what my router cost.
I was trying for hours to connect the USB Hard Drive of 3TB (My Book WD 3TB) in the USB port A and B of the router then the router won't reconize. I Have another the same model but different capacity and work excellent (My Book WD 2TB). What I can I do in order to use my hard drive in my network?
N600 router will not comunicate with my desktop computer through a cisco switch. The LAN was working fine when I was using a Linksys router. Is this a compatability problem between Belkin and Linksys products?