Configuring an asa 5505 with 8.42 software.I need to access an https server on the inside via the outside interface. have moved the http server enable to port 10443.Tried to make a "network object nat rule"
object network Vejrstation nat (any,outside) static interface service tcp https https object network Vejrstationnat (any,outside) static interface service tcp https https.
My internal network consists of Catalyst 3750 switches segmented into different VLANs. There is a default route on the layer 3 Catalyst switch sending all unknown traffice to the inside Internet of the ASA 5510. However, I'd like to have a separate VLAN for wifi guest access and send all of that traffic through one of the DMZ interfaces on the ASA 5510. I don't think you can have separate default routes based on VLANs on the 3750 switches so my only option is to make the ip address of the DMZ port the default gateway for all hosts on the wifi guest VLAN.
The problem I have is that I have a couple servers behind the inside interface that have services available to the public Internet via a NAT address on the outside interface. I want the guests on the wifi VLAN to have the ability to access the servers on the inside interface using the public address as well, but have not been able to come up with a solution yet.
Here is my config that pertains to this setup:
interface Ethernet0/0description Outside Interfacenameif Outsidesecurity-level 0ip address 76.47.10.x 255.255.255.224 rip send version 1rip receive version 1!interface Ethernet0/1description Inside Interfacenameif Insidesecurity-level 100ip address 192.168.17.1 255.255.255.0 rip send version 1rip receive version 1!interface Ethernet0/3description Wifi Guest Accessnameif DMZ2security-level 50ip address 192.168.60.1 255.255.255.0
global (Outside) 1 interface
nat (Inside) 0 access-list nonat
nat (Inside) 1 0.0.0.0 0.0.0.0
nat (DMZ2) 1 0.0.0.0 0.0.0.0
static (Inside,Outside) 76.47.10.x 192.168.17.88 netmask 255.255.255.255
I've tried the following commands below but no dice.
same-security-traffic permit intra-interface
static (inside, inside) 76.47.10.x 192.168.17.88 netmask 255.255.255.255
We have an ASA5505 UL bundel, updated with this license "L-ASA5505-SEC-PL=" to enable traffic from DMZ to Inside. No NAT or rules deployed for that yet.
On the Inside we have Exchange 2007 in a single server installation. The public url for smtp, ActiveSync, OWA and Outlook Anywhere is mail.company.se. There is a static NAT for outside traffic to access above mentioned services on inside. Now, on DMZ there is the WLAN for guests to access the Internet. How ever, our Smart Phones with WLAN turned on, cannot sync to the Exchange Server on the Inside! The DMZ gets IP-addressen from ASA on DMZ Interface with external DNS configured. How can I configure the ASA to achieve the function of ActiveSync from DMZ to Inside with the public URL from the phones?
I have an ASA 5505 with the base license,When I setup the DMZ interface I had to add the deny access to the inside VLAN. The DMZ works fine with WiFi on it, but user's iPhones can't get email unless they turn WiFi off.Is there a simple way to allow HTTPS traffic through the DMZ interface to our internal Exchange server which is NAT'd on the 5505's external IP?
View 3 Replies View RelatedWe've just started with the ASA 5505. We do run a DHCP server on the inside interface, so it is in the same VLAN 1 as all of the clients. However, we cannot get it to work.We can't use DHCP Relay, as the ASA 5505 only allows to relay to DHCP servers in a different subnet.Or do we have to move the DHCP server to a different subnet. If so, how would we configure that scenario?
View 13 Replies View RelatedI did this on the PIX and it worked like a charm, but I am having some difficulty translating the configuration to an ASA.
In the PIX I performed NAT on outside traffic to a specific inside host (web server) to map to the inside interface so that return traffic would go to the same firewall the traffic came in through, The reason for this configuration was because the gateway of last resort was a different firewall and not the firewall the traffic came in through.
Now to further give you some history, the gateway of last resort is an ASA running 9.1 (Now), prior to that it was a PIX with v8.0(4), traffic to the aforementioned web server came in through the gateway of last resort), which at the time was the PIX.
However, for some reason after swapping the PIX for an ASA (same rules, updated NAT rules for 9.1) access to the same web server is slow. Not sure why, but it’s the case. To alleviate the slowness we experienced, and until I can figure out why this occurs on the ASA, I placed a PIX on the network that only listens for traffic for the web server in question. On this PIX I map to the inside interface so that traffic flow works and external clients can access the web server with no issues.
So two questions, one I would like to use the configuration I have for the web server on the PIX on the ASA to see if that setup on the ASA works better, but having difficulty translating the rules to the ASA.
Second question, (Slow access with ASA to a web server, but fast with PIX to the same web server)?
P.S. Addresses in attached picture config are not real, but I know what they translate to.
we have a server that has an outside IP and an inside IP. It's inside ip is 192.168.222.30/24 and it's outside IP is 199.204.50.2/29. The connection to this server from the outside is perfectly fine, but access from inside users to the NAT'd IP which is 199.204.50.2/29 is having issues, however, access to the inside IP works fine (this part makes sense)Will It be a must to set the inside DNS A record to the inside IP and not the outside IP, or can users on the inside interface access the NAT'd IP which is assigned to the server
LAN(192.168.222.0/24)<=====>InsideASAOutside<=====>(Server with NAT IP 192.168.222.30/24, it's also physicall assigned to this server).This is an ASA 5510 with 8.4.
administrator wants to manage ASA 5500 using inside interface.{telnet or ssh].Allowed telnet and ssh in ASA 5500 but unable to get access from administrator PC..Is there a way to do it without enabling NAT on the ASA? Will a specific rule on ASA allow adminstrator to access ASA 5500 inside interface via ssh or telnet?
View 2 Replies View RelatedI am having a problem configuring my ASA 5505 for NAT.
View 3 Replies View RelatedI am trying to access and ping the inside interface of a ASA5505 from a remote network. From the remote network, I am able to access anything on the local network, but the ASA5505 inside interface.The 2 networks linked by a fiber link which have a transport network on another interface. From the remote network, I am able to ping the transport network interface IP, but I would like to be able to ping the inside interface IP. When I do a packet tracer, I get a deny from an implicit rule.How can I achieve that?
Here are the subnets involved and the ASA5505 config.
Remote network : 10.10.2.0/24
Local network : 10.10.1.0/24
Transport network : 10.10.99.0/24
[code]....
What I have is 3 interfaces on my PIX.- Outside: 216.116.87.0/24 (security level 0)
- 469: 172.16.6.0 /24 (security level 10)
- 571: 192.168.255.0 /24 (security level 1)
My users on 571 need to access a web server on the 469 interface. However, the requirements are that the 571 users can only access the Website using the public FQDN which there is a static NAT from outside to 469. [code] Here is also the Packet-Tracer and it shows what I expect that the traffic is source from 571 and exits 469. However, the users are not able to access the website.[code]
Using an ASA5505, have 1 static outside address, want to access an inside SBS-Server on SMTP, RDP (3389), HTTPS and port 987
Have configured network object nat rules using the asdm, SMTP works (I can telnet to the server on port 25 from outside), however for some reason I can not telnet inside and out on port 25, so outgoing mail does not work. RDP does not seem to work from outside, 987 I havent tested from outside. When I try to create a network object nat rule for https I get this message from the ASA:
[OK] object network SBS-HTTPS
object network SBS-HTTPS
[ERROR] nat (inside,outside) static interface service tcp https https
NAT unable to reserve ports.
I'm having trouble setting up the correct rules on an ASA 5505 I'm using in my home office. I have a couple of IP Cams I need to access remotely.
I've tried setting up simple NAT(PAT) and/or Access Rules, but it hasn't worked. I have a single dynamic IP for the Outside interface. Call it 77.76.88.10 and I am using PAT. The CAM is setup to connect on port 80, but could be configured if necessary. I've tried setting up NAT Rules using ASDM as follows:
Match Criteria: Original Packet
Source Intf = outside
Dest Intf = inside
[Code]....
I'm afraid to use CLI only because I am not confident I'll know how to remove changes if I make a mistake.
I have Pix 501 firewall and I'm just configuring the device for "Email Server" to allowing POP/SMTP.
Inside Interface Address: 132.147.162.14/255.255.0.0
Outside Interface Address: ISP provided IP address
My question is can my traffic goes from inside interface to outside interface? (because the inside interface address not from 10.0/172./192.168 private address)Also I'm allowing internet from this email server (132.147.162.14) so what my access list to be configured? and what my subnet mask shoud be there?
Pix(config)#access-list outbound permit tcp 132.147.162.14 255.255.0.0 any eq 80
Pix(config)#access-list outbound permit udp 132.147.162.14 255.255.0.0 any eq 53
Pix(config)#access-group outbound in interface inside
I would like to allow users from network 10.132.23.0/24, 10.132.33.0/24, 10.132.24.0/24 access to our SQL server(192.168.1.7) located on the inside interface(192.168.1.0/24 network) Those networks (10.132.0.0/16) come from the DMZ interface.
View 12 Replies View RelatedI have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
View 1 Replies View RelatedI've recently upgraded my old firewall from a PIX to an ASA5505 and have been trying to match up the configuration settings to no avail. I have is that I can't ping the new firewall on it's inside interface, despite having "icmp permit any inside" in the running config. Secondly, the server I have on there ("Sar") can't connect out to the internet.I've included the ASA's running config incase anybody can see if something stands out. I have a feeling it's either not letting anything onto the inside interface, or there is no nat going on. Lastly (and possibly relevant), the firewall is actually going at the end of a vlan, which is different to the firewall's inside vlan number. I don't know if this is actually the problem because the server can't connect out even if connected directly into the firewall.
View 32 Replies View RelatedI was unable to access the web admin on my WRT160n v3 w/ latest firmware this morning. Reset config to defaults & was able to get in. Enabled HTTPS access & disabled HTTP access & was right back where I started; reset to defaults again & left both boxes checked. Can access via HTTP, but HTTPS requests get refused/reset.
The reason I needed access was that when I booted up my laptop this morning, my wireless card wasn't picking up an IP address via WIFI, only worked via ethernet, so I need to see what was going on there — several reboots of the router didn't fix, nor has it fixed the HTTPS access problem described above.
I am trying to upgrade a Cisco ASA over an IPSEC VPN tunnel. My FTP server is on the remote side of the VPN tunnel but I am initiating connections from the inside interface of the firewall. I am currently managing the Firewall over the VPN via it's inside interface (using the management-access inside) command. When I try and update via FTP, the connection is going straight out the outside interface (and not across the VPN tunnel) I have tried upgrading via TFTP but it keeps stopping randomly with (unspecified error) I normally upgrade via FTP though but it's not working in this instance. Essentially what I am asking, is is there an equivalent command for FTP that there is for TFTP: tftp-server interface ip anyconnect I need the connections to originate from the inside interface so they traverse the VPN. I am running 7.2.3?
View 2 Replies View RelatedI have a new ASA 5505 and all is working fine, I can CLI and ASDM into it, but just can't ping the inside interface, do I need to enable a feature to make this work somehow?
View 1 Replies View RelatedI am connecting the inside interface to an upstream switch and therefore will need to assign a static IP address to the inside address as I did below:
#sho int ip brief
Vlan1 123.123.123.123 YES manual up up
I will also use this to manage the ASA. I am having a problem with the network configuration of the inside interface as I can't ping the gateway and/or the in IP of the inside interface.Do I need to add any routes?
I have a Cisco 5512 x Firewall connected with Cisco Layer 3 switch 3750.I have two different WAN connections, one for Data and one for voice. Cisco Layer 3 switch is configured with 2 different VLAN's one for data & other is Voice Vlan. Switch is providing DHCP to computers and IP phones. Voice Pool 192.168.10.0/24 Vlan10 and Data pool 192.168.20.0/24 Vlan20.I need to route my data & voice traffic separately. Cisco ASA is connected with two different ISP's. So, how can I do this configuration so that Voice and Data traffic will route separately.
View 7 Replies View RelatedI ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]
View 5 Replies View Relatedthe inside interface on our primary ASA seemed to "hang". It dropped all the packets it received. Because the interface didnt go down, failover didn't happen. Device's info;
-Cisco Adaptive Security Appliance Software Version 8.2(3)
-Device Manager Version 6.3(3)
-Hardware: ASA5550, 4096 MB RAM, CPU Pentium 4 3000 MHz
-Internal ATA Compact Flash, 256MB
-BIOS Flash Firmware Hub @ 0xffe00000, 1024KB
I attached a capture picture shows that traffic didnt go to the roof when the issue happened. Why the interface would "freeze" randomly?
i have here a ASA 5510 sec k9.
I build a Config with a DMZ,INSIDE and OUTSIDE Interface. My Plan is to use the IP-Address of the OUTSIDE Interface with PORT to setup a HTTP Server In the DMZ
But my Config doesn't work. And I have no Plan why .....
The Inside Interface have to work normal. The Traffic to the Internet is TRiggert from Inside with Dynamic PAT
ciscoasa(config)# exit
ciscoasa# show run
: Saved
:
ASA Version 8.4(1)
[Code].....
I have an ASA 5505 that I'm trying to set up a guest network on. I've configured an interface as a trunk and allowed the 2 vlans but I'm not getting any layer 3 to it. The switch connected to it is a 3560 and port is configured as a trunk with the same vlans.
I can't ping the ASA inside interface but I see its MAC address in the swtich's table.
[code]....
I'm trying to NAT SIP registration from OUTSIDE interface to Inside interface on ASA
View 1 Replies View RelatedThe ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config.
ASA Version 8.2(1)
!
firewall transparent
hostname issr1
enable password 2alej83t5cqT0FWd encrypted
passwd 4kleUY438I93.4ljdh encrypted
names
[code]....
I have a PIX 515e running version 7.2(4).I have 2 interfaces - DMZ3 (sec lvl 50) and LAB (sec lvl 100) behind the pix. There is also the OUTSIDE interface (sec lvl 0) which connects to the internet.In DMZ3 I have a webserver - x.x.124.217/24 (host is NATed via static command to public IP)In LAB I have a server - x.x.1.203/24 (entire range is NATed via NAT/Global statements to public IP)The server in LAB needs to access a webserver in DMZ3. From the internet both of these hosts have public addresses that are NATed into the inside addresses. I can reach the webserver from the internet, but not from the LAB interface.I think I have to add a static command so that the LAB host can access the DMZ3 host without accessing the internet.
View 3 Replies View RelatedI need to configure a Cisco ASA5510.Connencted the a single interface I have a switch. To this switch (same VLAN) there are connected:
1. The Subnet of the main office (192.168.1.253)
2. A router (IP 192.168.1.254) that routes the traffic to a remote location (Subnet 192.168.8.0/24)
I have so allowed any traffic incoming to the inside interface as follows:access-list inside_access_in extended permit ip any any and I have permitted traffic intra interface as follows: same-security-traffic permit intra-interface. [code]Unfortunately I cannot RDP into that server. When I simulate the connection via Packet tracer, it tells me that the implicit deny on the bottom of the connections from "inside" (firewall) does not allow the connection. It sounds to me like that "same-security-traffic permit intra-interface" does work only if there are 2 interfaces and not a single one.Unfortunately I cannot just unplug the cable and connect it into another port as the ip is on the same subnet and I cannot configure the other end router.
I have ASA5505 configured with internal network as 192.168.15.0 and default gateway 192.168.15.1 From the inside network, i'm able to access internet and able to ping all website (enabled ping). and all internel network devices can ping each other. Except i cannot ping my gateway (ASA5505) 192.168.15.1. I'm continously seeing this message on the log, when i tried to ping.. How to fix this?
Denied ICMP type=8, code=0 from 192.168.15.xxx on interface inside
replace xxx with my network devices that try to ping the gateway..I dont want outsiders ping my gateway, i need ping for inside internal network only.
I have inherited an ASA 5520. In doing some auditing of the setup, I have noticed a Static Route that has the inside interface of the ASA as the Gateway IP. I am trying to understand the purpose of this route or why a route would be setup this way.
Example Static Route:
Inside 10.xx.31.0 255.255.255.0 10.xx.xx.10 (10.xx.xx.10 is the inside interface of ASA)
We have a Cisco ASA 5505 (v7.2(3)) with a "fairly" normal configuration yet we have a problem where it appears UDP/53 traffic is denied on our inside network.
here is output from our sys log:
SyslogID Source IP Dest IP Description
305006 172.18.22.3 portmap translation creation failed for udp src inside:172.18.22.156/42013 dst inside:172.18.22.3/53
To give some clarification:
172.18.22.3 is one of our DNS servers
172.18.22.156 is a device we're experimenting with.
We've bypassed the Cisco by using a 4G wireless router with this same device - and it works flawlessly.Here is a [scrubbed] copy of our config. It is what I inherited from the previous admin - I'm not sure of all its finer points (I'm not Cisco certified -- perhaps I'm just certifiable.)
: Saved
:
ASA Version 7.2(3)
!
hostname [redacted]
[code].....