Cisco Routers :: WRVS4400N VPN Tunnel Between 2 Physical Locations

Dec 7, 2011

I have 2 WRVS4400N's installed in our network, one at each end of a VPN tunnel between 2 physical locations.  I continue to have issues with the VPN to "Stay" connected, even after purchasing another new WRVS4400N 4 months ago.  I can reboot both routers, and the VPN connects with no problem, but hangs up after a few hours / days (no pattern). 
I am taking a hard look at the issue now, as about 1 month ago, the newest router "automatically" reset it itself back to factory settings (thus interrupting nearly everything in our network).  After contacting support, we reset the router and re-configured it to our environment.  It is plugged into a surge protected UPS (yep, I thought maybe a power issue caused the problem, but it's not).  Then about 1 week ago, the other/older (9 month old) router lost it's configuration.  again, reset it and all works.  Including the VPN, but the VPN still works as it did before connects for a while, but then drops and generally I need to reboot the router to get it connected again (clicking on the Connect on either router doesn't work until after a reboot).
Also, in light of the recent "lost configurations", I turned on logging and now I'm getting TONS of emails of log activity, even when the network is idle (no users, no background jobs running). 
after rebooting and no inter activity, I get this kind of log, all night long (to me it generally looks like the VPN connection resets and increments by 1... I'm taking a guess that the increment hits a limit someplace and I lose my VPN).[code]

View 6 Replies


Cisco Routers :: WRVS4400N - VPN Tunnel Between 2 Locations

Dec 17, 2011

I have establlished VPN tunnle between 2 locations
I can ping accros and access server resources on both LANs The problem is that from one location I can not access Internet
I can not ping by IP,when I do tracert it just reaches default gateway of this locations from other location(office) no problem

View 1 Replies View Related

Cisco Routers :: RV042 - VPN Tunnel Between Two Remote Locations

Jun 27, 2012

I have configured a VPN tunnel between two remote locations using static IP addresses on two RV042 routers. The tunnel seems to work but the problem is that when the two hosts attempt to ping each other only one can successfully ping. One PC with IP address can ping across the network but the second PC with IP address cannot. These are laptops seperate from the intranet used to test the tunnel. Someone had suggested NAT may be the issue so I enabled NAT Transverse on the routers but still no luck. The following is the results from a ping test.

PC 1
Pinging with 32 bytes of data:
Reply from bytes=32 time=116ms TTL=63
[Code] ......

View 1 Replies View Related

Cisco Routers :: WRVS4400N - VPN Tunnel Down

Aug 5, 2012

I have a gateway to gateway vpn (home-office) working fine for almost an year btw 2 wrvs4400n routers, This morning, the VPN tunnel was down. I clicked "Connect" from the web based interface, but it does not reconnect.
I tried setting up a new tunnel using the VPN setup wizard, but it says it can't connect to the remote router. Which is strange, since I can ping there normally.

View 2 Replies View Related

Cisco Routers :: WRVS4400N - VPN Tunnel Up But No Outgoing Traffic?

Jan 29, 2012

we've buyed a WRVS4400N to create a IPSEC VPN tunnel to our client in order to access some applications.
After a while trying to configure the router, we have archieved it and the VPN tunnel is up. We can see the tunnel up from here and from client's side as well.
Our client supposendly have created the tunnel in order to access a list of specific IPs in the range 10.113.x.x, but if we try to access this IPs via telnet whe cannot obtain any response.
Making a tracert, we obtain...
Traza a sobre caminos de 30 saltos como máximo.
1     1 ms     1 ms     1 ms
2     *        *        *     Tiempo de espera agotado para esta solicitud.
3     *        *     ^C
... and therefor the client doesn't receive any packet at its firewall.
I've tried to establish a static route for to their remote gateway, but I'm unable to add any entry to static routing list... The router tries to do something, but afterall I cannot see the new entry...
What can I do to route the traffic through the tunnel?

View 1 Replies View Related

Cisco Firewall :: 5510 - VPN Tunnel Between Two Locations

May 23, 2011

Firewall ASA5510. I'm planning to get one of ASA5510 for our office in order to secure our network properly, however we have quite specific routing configuration to allow us failover to the remote location (data center) in case of any disaster with our server. I'd like to find out if I can just install firewall between our ISP Ruter and internet and allow traffic to/from Data Centre. In this situation will I have to change routing configuration on Company Router or do I have to do anything with our Company Router

View 1 Replies View Related

Cisco Firewall :: ASA 5510 Tunnel - Replicate Data Between Two Locations

Oct 3, 2012

I am not a ASA expert but I have configured them few times. I have a vision of a task I have to complete but not sure if it is practical or how to go about doing it.
We two locations, Location A and Location B. Both locations have a 100MB internet conection. Location A has a ASA 5510. Location B has a 5505. Users at both locations access the internet via their respective ASA. Location A is the headquarters and Location B is a disaster recovery site. We want to setup a tunnel between both ASAs. This tunnel will be used to replicate data between the two locations for DR purposes. We need the users to still use the same pipe to get to the internet but want to allocate 10MB for internet use and the remaining 90MB for the DR tunnel.

View 30 Replies View Related

Cisco VPN :: Tunnel With WRVS4400N Need To Push 2 IPs Through Tunnel?

Jan 23, 2012

There are a few situations were I'd like to be able to use the locally configured account on a device but still have ACS in place.I want to complete this WITHOUT adding the locally configured account into ACS.I have tried setting the advanced option under Identity for if an account is not found to "Continue" however this causes the account to be allowed as long as a password is typed (any password, as long as its not blank).

View 2 Replies View Related

Cisco WAN :: ASR 1002F - Per Tunnel QoS And Physical Interface CBWFQ

Jun 5, 2012

I am preparing configuration (currently in lab) for Per-Tunnel QoS in DMVPN on ASR 1002F for one of our customers, and I came across one issue. According to restrictions for this feature, I cannot apply per-tunnel QoS in conjunction with interface based QoS. This means, I can provide shaping with hierarchical CBWFQ for each spoke, but I cannot guarantee anything on physical interface! What if there are services in native MPLS? I am also unable give reservations for BGP which is used on PE-CE link! How about monitoring spoke PE-CE links natively? I can only apply policy-map with class-default on physical interface. When I add anything related to queuing for that class (or any other non-default class) I get the message:
R1(config- pmap)class routing
R1(config- pmap-c)#bandwidth 16
service-policy with queuing features on sessions is not allowed in conjunction with interface based
[Code] ........

View 8 Replies View Related

Media Disconnected And No Physical Address Under Tunnel?

Apr 27, 2012

My hard drive crashed and I replaced it with a old hard drive that I had and now I cant get connected. I tried different things I have on site and its still not working. After trying the last thing I have given up ..

Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:Windowssystem32>IPCONFIG /ALL
Windows IP Configuration
Host Name . . . . . . . . . . . . : Tonya-PC
Primary Dns Suffix . . . . . . . :


View 14 Replies View Related

How To Use 2 Wireless Routers Together In Different Locations

Jan 28, 2012

Has a small home network in 2 buildings with 2 wireless routers. He has fiber from the building where the dsl comes into, running up to his house where a second wireless modem is. Both are broadcasting DHCP but I only want one of them to do this. Ultimately I want his server(2008) to broadcast DHCP, but just one of the modems is fine for now.

View 1 Replies View Related

Connect 2 Routers In Different Locations?

May 1, 2012

I know how to connect 2 routers in 2diffrent states using internet.Also which service is used for that purpuse

View 1 Replies View Related

Cisco VPN :: WRVS4400N - Need To Push 2 IPs Through Tunnel

Mar 14, 2011

I have a VPN tunnel with an WRVS4400N (teleworker) on one side and sonicwall firewall on the other. I need the telework's router to know to push two ip's through the tunnerl, 9.19.178.(   ) and 172.20.0.(   ). It looks like when you setup the tunnel you can only do one. The tunnel does work with 9.19.178.(  ) but how do I tell the router to also push 172.20.0.(  ) traffic through the tunnel as well?

View 1 Replies View Related

Routers / Switches :: LAN Setup For 3 Different Office Locations?

Jun 28, 2011

I have 3 different office location and I need to set up a LAN so that all three are connected and can share info?

View 1 Replies View Related

Routers / Switches :: How To Connect Offsite Locations Together

Jun 21, 2011

I work as a systems administrator for a global company and currently right now all my end users which is roughly 300 all use VPN from there office location to dial back into the server or use terminal server. I would like to know how to connect there locations back to main site without using VPN. What would be the cheapest and or easiest method to complete this.

View 1 Replies View Related

Cisco Firewall :: ASA 5505 And Small Business WRVS4400N VPN Tunnel

Mar 21, 2012

I'm trying to establish a VPN tunnel between our main office running a Cisco ASA 5505 [8.3(2)] and a remote user using a Cisco Small Business WRVS4400N firmware version V2.0.1.3.
The Cisco ASA 5505 is already configured to allow incoming IPSec VPN connections via the Cisco VPN Client.
Is this possible, and if so, how would I go about doing so? The remote user has a static IP address as well as the main office.
I'm trying to establish a VPN tunnel between our main office running a Cisco ASA 5505 [8.3(2)] and a remote user using a Cisco Small Business WRVS4400N firmware version V2.0.1.3.
The Cisco ASA 5505 is already configured to allow incoming IPSec VPN connections via the Cisco VPN Client. Is this possible, and if so, how would I go about doing so? The remote user has a static IP address as well as the main office.

View 2 Replies View Related

Cisco Routers :: Set A VPN IpSec Tunnel GW To GW Tunnel Between RV110W

Oct 17, 2012

I am using a Cisco RV110W (Firmware 1.2.09) in a branch and I would like to create a VPN Tunnel to another site that has a Cisco RV042 (firmware v4.2.1.02)
What would be the correct Configuration? the current configuration I am using is
in the RV042 i am using
Check Enable 
Local Group Setup
Local Security Gateway Type : IP Only
IP Address : RV042 Pulbic IP address


View 3 Replies View Related

Cisco Switching/Routing :: ASA5510 / Two Routers On Same Physical Lan With Identical VLANs On Each?

Mar 17, 2013

I have 2 ASA5510's acting as routers/firewalls, setup on a LAN, each one pointing to a different gateway (different ISPs), and the exact same VLANs set up as sub-interfaces on each of these. Both act as DHCP relays to a Windows Server 2008 DHCP server. All the Trunking has been setup and works. When I Untag a switch port, and point it to whichever gateway?

View 2 Replies View Related

Networking :: To Tunnel All Routers Traffic Through SSH Tunnel With WRT300n

Jul 24, 2012

Environment :linksys wrt300n v1.1 which can have ddwrt-mega. Willing to tunnel all lan's outbound traffic through an ssh tunnel.

View 2 Replies View Related

Cisco Routers :: WRVS4400N WAN Interface Down?

Jul 5, 2011

Right out of the box, the WRVS4400N [firmware v2.0.1.3] I just purchased says the WAN interface is DOWN; and it simply will not obtain an IP address from the Arris TM602G cable modem it is attached to. Internet still runs great on the old WRT54G. Is this WRVS4400 DOA? Or is there some arcane setting the quickstart guide overlooks? OR?

View 2 Replies View Related

Cisco Routers :: How To Configure WRVS4400n

Dec 7, 2011

I'll just use the 4400n to provide DHCP to my two VLANs and then a new problem cropped up.  I am unable to add a default route to the 4400n's DHCP server.  It uses the 4400n's vlan IP as the default route.  What I'm trying to ultimately achieve is to configure the 4400n as an access point for our "private" network on vlan1 and also "guest" access to the internet on vlan2.

View 12 Replies View Related

Cisco Routers :: WRVS4400N V2 - Setting Up VPN For Mac?

Mar 3, 2013

I'm having problems trying to establish a IP Sec tunnel from the office to home. All of our machines are Macs so I have been using the directions described in "How to create an IP Sec tunnel for MAC Clients, A QVPN alternative" but I still can't get it to work. My setup is as follows:
The office is connected to the outside world through a MODEM (Sagemcom 2864 Connection Hub). This MODEM is also a wireless router. It's DHCP server provides addresses 192.168.2.x.The WRVS4400N's WAN port is connected to one of the LAN ports on the MODEM. It's IP address from the MODEM is 192.168.2.x. The WRVS4400N provides addresses 192.168.21.x to devices connected to it.We have a DynDNS account and are using the DDNS client on the WRVS4400N router to connect to it.At home, we have a DIR-655 router with IP Sec Passthru enabled. The router provides IP addresses 192.168.1.x for all devices connected to it. I am fairly sure there are no issues with the router setup at home since I am able to VPN into the office of my full-time job without any problems. I have tried just about everything I can think of but have not been able to get this to work. setting up the Local and Remote Group Settings on the WRVS4400N and the IP address settings in IP Securitas?

View 2 Replies View Related

Cisco Routers :: WRVS4400N VPN Log Shutting Down

Sep 16, 2011

Ive setup a few WRVS4400N over the past 6 months, and have been receiving the below message from some of them every couple of hours.What does the message indicate?

View 1 Replies View Related

Cisco Routers :: DNS On Modem Or WRVS4400n?

Sep 15, 2012

I have successfully got QuickVPN working from Windows 7 64bit into my WRVS4400n.  The router is sat behind another router/modem (Belkin) as the UK uses PPPoA and the WRVS4400n doesn't.So I set up DMZ and changed the DHCP to always allocate 10.x.x.2 on the Belkin which is the WAN side for the WRVS4400n as it is the only thing attached.I have now noticed, and I'm not sure whether it was the case before, that the DNS that the WRVS4400 is showing is the LAN address for the Belkin  Modem/Router (10.x.x.1), not 192.x.x.1 for the WRVS4400n itself.  I assumed setting the Static DNS 1 on the WRVS4400n would do it, but it didn't?When I connect into the network with QuickVPN, the computer names do not show even though I have selected the option in QuickVPN?

View 1 Replies View Related

Cisco Routers :: WRVS4400N Does It Support EAP-TLS

Aug 8, 2011

Our business was looking at purchasing one of these Cisco routers and were curious if it supported WPA2 EAP-TLS?

View 2 Replies View Related

Cisco Routers :: Using WRVS4400N As Gig Switch Only?

Jul 23, 2012

I have 2 WRVS4400N's  available to be. One is running my network and security connected to my WAN.I want to use the other one stricly as a switch or even adding wireless repeat of my current wireless LAN.

View 1 Replies View Related

Cisco Routers :: WRVS4400N Cannot Browse Anything

Dec 16, 2012

Recently installed a WRVS4400N router on my home network. Prior to that I was using the wireless built into my FIOS router. I wanted something more secure so I went with the WRVS4400N. I turned off the FIOS wireless and am only using the cisco wireless.

Im having intermittent issues with the wireless. I have many things hooked up to my wireless including a HP printer and a Sonos system. Most of the time if I just open my ipad I cannot see anything else on my network including the printer. If I try to see the Sonos system can cannot, sometimes I can open the app on my iphone and then I can see it.

Sometimes I can see the printer and sometimes I cant. Sometimes when I do see it and then print to it, it will be gone before it even prints.
I don’t seem to have any issues thru the LAN connections.
Also, ive noticed that the wifi is much slower than the old FIOS box.
FYI, when I remove the cisco and fire back up the FIOS wifi I don’t have any problems at all at any time. And its much faster.
I have tried channel 6, 11 and auto. Also turned off IPC and still no change.

View 1 Replies View Related

Cisco Routers :: Connecting WRVS4400N VPN To Another

Oct 15, 2011

I'm having a heck of a time connecting the WRVS4400N VPN to another WRVS4400N VPN. both of the routers have the current firmware version V2.0.2.1: Router 1 is below, and router 2 has the matching configuration with as it should be the local group being that routers local information and the remote crew set up being router ones information. the status is up on both of the routers, but I'm unable to ping the remote gateway or any device behind it.[code]

View 5 Replies View Related

Cisco Routers :: WRVS4400N V2 - DIAG Always On / No Access

Apr 21, 2012

After a few months of trouble-free ... the Cisco WRVS4400N V2 stopped working. i have tried to reset by holding the reset button for 30 seconds ... but nothing changes the red DIAG light remains on at all times
i have also tried two different versions of the Firmware Rescue Utility but all i get is "unable to scan"

View 1 Replies View Related

Cisco Routers :: WRVS4400N - Setup VPN Connection?

Apr 6, 2013

How to setup VPN connection,
Head office : fortigate 200b firewall - SSL, IPsec
Branch office: WRVS4400N Wireless-N Gigabit Security Router with VPN
Both side have the public IP.

View 1 Replies View Related

Cisco Routers :: WRVS4400N - Cannot Connect After 5 Minutes

Feb 2, 2012

This is a new device, just initially installed about a week ago.  I updated to the latest firmware.  We have iphones, ipads, and Samsung Galaxy smartphones all trying to connect to this WAP at this office, but cannot seem to connect.  If I power cycle the WAP, we can connect for about 5 min, then it loses it and cannot connect again.   I have strong signal, device says "connecting" then immediately "disconnected"... does this on loop forever.WPA/WPA2 PSK.I don't know what to do.  About to go buy an Apple WAP.

View 3 Replies View Related

Cisco Routers :: WRVS4400N VPN Pass Through Not Working

Sep 18, 2011

My WRVS4400N is not letting my VPN client through the router. I have checked the passthrough boxes for all 3 protocols. I have port range forwarding for my VPN connections to my SBS2008 box on port 1723.

View 5 Replies View Related

Cisco Routers :: Operating WRVS4400N As A Bridge?

Oct 17, 2012

I have a Linksys E4500 as the main router and would like to use the WRVS4400N as a bridge to extend the range of my network and also attach a NAS to it.  Is this possible?  I've been trying different options but have been unsuccessful. 

View 1 Replies View Related

Copyrights 2005-15, All rights reserved