Cisco Switching/Routing :: IOS Latest Stable Version 6513 With Sup720

Mar 29, 2012

I have Cisco 6513 with sup720 running  s72033-adventerprisek9_wan-mz.122-18.SXF8.bin.  I would like to upgrade with the latest and stable IOS.

View 5 Replies


Cisco Switching/Routing :: 6509-E Supported Switch Modules With Latest Stable IOS 12.(33)

Oct 14, 2012

I recently ran an upgrade on my 6509-E's and when the first switch came back up, 3 of the 10/100 switches that were in the chassis did not power on. After further investigation, these models are not supported by this latest IOS version. The module # is : WS-X6248-RJ-45
We have one WS-X6348-RJ-45 and since it was a few weeks ago I did this I can't remember for sure but I believe this one came up.
Where can I found the information regarding this being unsupported but I know it is out there and any page that showed me that this was unsupported with the latest stable IOS of 12.(33).
In addition to this question, I have approval to purchase some newer gigabit switches that will be supported by this new IOS version and hopefully at least the next few over the next few years. Which specific gig models are currently and hopefully should be supported for the next few years? I don't need PoE or anything spectacular, just regular switches that are attached to either servers or virtual hosts. I've been looking at the lists of what is out there and it seems like there are hundreds of different models and it is becoming difficult to determine what is what.

View 1 Replies View Related

Cisco Switching/Routing :: Different Netflow Export Profiles On Cat 6513 With Sup720

Aug 28, 2012

Is it possible to have one netflow export profile (may not be the right word...) to send all the flow information to one collector and another profile to only send traffic to and from centain IP addresses to another collector? If it is possible on the hardware and software, any quick sample config?
#sh ver
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXH4,
#sho module 7
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  7    2  Supervisor Engine 720 (Active)         WS-SUP720-3B       SAL1115LJBR
Mod MAC addresses                       Hw    Fw           Sw           Status
--- ---------------------------------- ------ ------------ ------------ -------
  7  0017.9444.9814 to 0017.9444.9817   5.3   8.4(2)       12.2(33)SXH4 Ok
Mod  Sub-Module                  Model              Serial       Hw     Status
---- --------------------------- ------------------ ----------- ------- -------
  7  Policy Feature Card 3       WS-F6K-PFC3B       SAL1115L2NH  2.3    Ok
7  MSFC3 Daughterboard         WS-SUP720          SAL1115LH7W  2.6    Ok

Mod  Online Diag Status
---- -------------------
  7  Pass

View 2 Replies View Related

Cisco Switching/Routing :: Best Current Stable IOS Version For 6509E?

Jul 2, 2012

upgrade experience with the 6509E on what IOS version to use. This is a new install, so I want the most current version that supports SSH and works with dual supervisors.
Here is some information:
WS-C5609-E with 983008K/65536K bytes of memory
Current version 12.2(18)SXF17b
Slot 5 Supervisor 720 (Active)
Slot 6 Supervisor 720 (Hot)  
Just need a strong base code, no advanced services. Let me know if you any additional information. 

View 2 Replies View Related

Cisco Switching/Routing :: 6513E What Current IOS Version Should Run On Sup720

Jan 23, 2012

We are close to receiving our new 6513E chassis which I will be running Sup720 cards in. This will be replacing our existing 6509 Sup2 setup in production. What current IOS version should I run on the Sup720 ? I would like to support SSH. The chassis will be populated with a couple of 6724 SFP cards, 2 6704 10 gig cards and a few 6748 line cards.Is there a good intitial config guide ?

View 6 Replies View Related

Cisco Switching/Routing :: 5505 Latest OS Version - 9.0.2 Or 9.1.1?

Apr 23, 2013

On the downloads page there's a 9.0.2.ED listed as the 'latest' but then if I expand the '9' below it I get to 9.1.1.ED. Which one is the actual latest? is there any way to tell the one that is not an 'interim' version I think 9.1.1 is also listed under interim?

View 4 Replies View Related

Cisco Switching/Routing :: 2960 S - Upgrade To Latest IOS Version

May 30, 2013

I am going to upgrade a number of catalyst 2960s-switcher to the latest IOS- version. The best solution for me would be if all the switches could be reloaded at the same time to shorten the maintenance-windows. So my question is: If I run the upgrade (archive down load -sw) before the maintenance-windows WITHOUT the reload-option, will then the switches continue to run without interruptions with the current IOS- version and config until I run reload manually?

View 3 Replies View Related

Cisco Switching/Routing :: Router Upgrade 2811 To Latest Version

Aug 22, 2012

I upgraded a 2811 router to the latest version and apparently everything went smooth.   I reloaded and did a sh ver the IOS show the correct version, but the boot strap shows the old IOS.  How can I change the boot strap to show the new IOS.

View 4 Replies View Related

Cisco Switching/Routing :: 6513-E / 6513 And WS-X6748-GE-TX Compatibility

Oct 29, 2012

we have a chassis 6513-E and a module WS-X6748-GE-TX, I'd like to know if could I put this module in any slot, since the documentation from Cisco says that any slot from a chassis 6500-E Series can support this module. And then in the documentation of WS-X6748-GE-TX says that this module is not compatible in the slots 1-8 of the 6513 chassis, only from 9th to 13th slots, in those slots from the 6513-E we already have 4x WS-X6748-GE-TX, and we'd like to know if could we put the module in the rest of the slots. The 6513, and 6513-E is kind of confusing.

View 4 Replies View Related

Cisco :: Sup720 - Supported Slots On A 6513?

Nov 28, 2011

Can the sup720b be used in any other slot on a 6513 besides 7 and 8?

View 1 Replies View Related

D-Link DIR-655 :: How To Downgrade Back To Stable Version

Dec 25, 2012

I've had the DIR-655 for a few months now, along with a Motorola Surfboard sb6121 DOCSIS 3.0.Modem works fine, the router was working perfectly fine until recently last week.

I have a desktop hardwired and a wireless network going on that I use just for my mobile phone and tablet at times. At first I was having disconnection problems with my wireless, then noticed a neighbor installed a similar router in the area according to my wifi analyzer, so I changed the channels and my wireless started working great. During this process I also did a firmware update and since then I've been receiving some really poor browsing problems, sometimes I'll visit websites like Facebook, or a news website, and it'll say something about the DNS not working, (at this point I'll ping the website and it still pings fine without any loss) so I'll visit the website about 10 minutes later and it works great. I've done extensive research on forums/Google and found it must link up to the new firmware update and something about a DNS relay? My version is:  Hardware Version: B1 Firmware Version: 2.10NA   

In other words, is there a way I can fix this issue from disconnecting without having to downgrade back to the old firmware? Or is this a common issue they'll continue to happen? If I do downgrade, HOW do I downgrade back to the stable version?

View 14 Replies View Related

Cisco WAN :: ASR 1002 Fixed Stable Code Version

Jan 22, 2013

I am looking upgrade my ASR routers to a newer code.  I am running asr1000rp1-advipservicesk9.03.03.01.S.151-2.S1.bin now. Would like input on what a good stable version is. I am not bleeding edge so the latest version I won't trust.

View 5 Replies View Related

Cisco Switching/Routing :: Most Stable IOS For Cat 3750?

May 17, 2013

what is a good IOS version to stick on a 3750 (normal, no X or G series) switch? This is being used for a Cisco Lab in my CCNP - SWITCH studies.Normaly I referance INE's site though they dont have a 3750 (only 3560) IOS recommendations.

View 6 Replies View Related

Cisco Switching/Routing :: 881 - How To Get Stable Connection

Nov 16, 2011

I am having some difficulties to have a stable connection on a Cisco 881. I have a IP Sla running with an ICMP-ECHO towards the uplink router. Linked with this is a tracking on the IP SLA so I can shutdown an HRSP instance with the tracking. The desired result is with this that when the nexthop becomes unavailable HSRP switches to the second router with the backup connection.
Regardless whatever timeout or threshold, the tracking switches at a random point when the line is somewhat congested. Debugging it shows me only a time-out on the IP SLA.
Is there anything possible to get the icmp-echo to retry it 2-3 times or so before going it's status is set to failure? [code]

View 2 Replies View Related

AAA/Identity/Nac :: SUP720 ISE Supported Switch IOS Version

Apr 18, 2012

The table referenced in the new 1.1 ISE guide show 12.2(33)SXI6 is the minimum version for support. Does this mean this version or above? Does ISE is tested in newer SXJ streams? We have a massive rollout of SUP720s to do and need to know the most stable version to load in preparation for ISE.

View 1 Replies View Related

Cisco :: Upgrading From LMS 3.0 To Latest Version?

Apr 26, 2012

Upgrading from cisco LMS 3.0 to a higher version.
Whatdoes it require?. What is the current version? What do we need for upgrading? Are there specific codes or new need to buy new products? In case of buying new products, which are the configurations?

View 3 Replies View Related

D-Link DIR-825 :: What Is The Latest Firmware Version

Dec 11, 2012

what is the latest firmware version for d-link dir-825? It tell me that i currently got the 2.60VT, is it the last one? If no, where can i download and how the latest version?

View 14 Replies View Related

Cisco AAA/Identity/Nac :: Configuration Between ACS 4.2 And ISE Latest Version

Jan 26, 2013

We are a Small company with 400-Users and currently we are using ACS 4.2  at our company.we want to upgrade and use Cisco ISE Appliance instead.
I want to know is there any major changes in configuration between  ACS 4.2 and the ISE Latest Verizon.?
Is there any Hardware (Switch or Cisco AP ) compatibility issues with using Cisco ISE. (we are currently using Cisco Cat 3550 and Cisco Aironet 2600 APs  with the existing ACS4.2) What ISE Series & what Soft version are the latest so i can order ?

View 2 Replies View Related

Cisco Firewall :: 5505 Latest Version Of OS Available

Jun 20, 2012

I have a ASA5505 and currently running Version 7.2(4). I was wondering what the latest version of the software would available to me would be.
Here's a show ver
Cisco Adaptive Security Appliance Software Version 7.2(4)
Device Manager Version 5.2(4)
Compiled on Sun 06-Apr-08 13:39 by builders
System image file is "disk0:/asa724-k8.bin"
Config file at boot was "startup-config"
Hardware:   ASA5505, 256 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB

View 1 Replies View Related

Cisco :: What Is Latest Version Of Secure ACS4.1

Apr 10, 2011

I am working at a client site today whom has Cisco ACS employed.  Their current version is 4.1.  It has been some time since I have done any upgrades on this system.  What is the most current version for this appliance?

View 5 Replies View Related

D-Link DIR-655 :: List Of Changes For The Latest Firmware Version?

Jan 8, 2011

Where the list of changes for the latest firmware version can be found?  My new DIR-655 has firmware from May 2010, and I see the latest and greatest on the DLINK website is from September.  But it doesn't state what the changes are, so I'm not sure if I should upgrade or not.

View 8 Replies View Related

Cisco :: R-PI-1.1-500-K9 How To Upgrade To Latest Version Of Prime Infrastructure

Apr 9, 2013

We just purchased the following items:
(1) R-PI-1.1-500-K9
 I want to know how I can upgrade to the latest version of Cisco Prime Infrastructure.

View 1 Replies View Related

Cisco Firewall :: ASA 5550 - IOS Upgrade To Latest Version?

Jun 12, 2013

I have a ASA5550, with a IOS version 8.2(5).
I would like to upgarde to the latest version, and I believe it is 9.1.1.

View 1 Replies View Related

Cisco AAA/Identity/Nac :: Can Latest Version Of ACS 4.0 Support Nested AD Groups

Dec 20, 2012

We are running ACS 4.0 so understandably so we are looking to upgrading to a Cisco supportable version of ACS.  The limitation of our current version of ACS does not support nested AD groups.  The latest version of ACS (I think it is 5.4) will?

View 1 Replies View Related

Cisco Wireless :: WLan Controller 5508 - Latest IOS Version

Apr 23, 2013

What is the latest IOS version for the WLan Controller 5508 ?
Actually I am using, Software Version7.3.102.0 
I see the following at Cisco website: 

Latest Releases

View 1 Replies View Related

Belkin Routers :: F9J1106 What Is Latest Firmware Version

Jan 31, 2013

Just purchased a Belkin AC1200 Router Modem and unable to locate the model number what is the current firmware version It is the UK model and I guess it must be very new?

View 4 Replies View Related

Linksys Wireless Router :: E-2100L - When To Get Latest Version

Feb 17, 2012

 When you will release the latest version for Wireless router Linksys E2100L?, because I bought a MAC with Lion and I can´t use my Router.

View 4 Replies View Related

Cisco Switching/Routing :: How Many Session Can Use In Sup720-3b

Aug 30, 2012

I will use function of span in sup70-3b.How many session can use in sup720-3b? For example, 2 or 4 session.

View 1 Replies View Related

Linksys Wireless Router :: What Is Latest Firmware Version For WRT160n

Jan 20, 2013

what is latest firmware version is for router WRT 160n (v1). The Linksys site currently states that it is Ver.1.02.11 (11/08/10). However, on the admin page for my actual router it states v1.52.0 Nov 16, 2007.  These versions #s and dates don't jive. How could I have a supposedly newer version that is older than the most recent one posted? 

View 3 Replies View Related

Cisco Switching/Routing :: Need To Know Serial Number Of Sup720

Dec 10, 2011

How can i find the serial number of sup-720 which is totally dead and not boot?By which sticker on SUP and where ? How many digits ?

View 4 Replies View Related

Cisco Switching/Routing :: Sup720-3BXL Stuck On SP

Mar 19, 2013

I have a SUP720-3BXL that will not boot. It will get stuck at booting from the SP. It never switches over to the RP.  [code]

View 5 Replies View Related

Cisco Switching/Routing :: SUP720-3B Internal Flash

Dec 1, 2011

I have received a sup720-3B from Cisco with an internal 512MB flash(sup-bootdisk). I want to verify what IOS image is on the disk and do not have an spare 6509 chasis. Can I remove the 512 MB flash disk and insert it to my disk0: on my production 6509 with the sup32 that the 720 will repplace and view what is on the disk without corrupting?

View 7 Replies View Related

Cisco Switching/Routing :: MLS Statistics On Cat 6500 With Sup720

Sep 11, 2012

when using "show mls statistics" I see a lot packets are getting L3 Processed. Does that mean they are getting software-forwarded?

IOS is 12.2(33)SXI5. 
Cat6k#show mls statistics
Statistics for Earl in Module 5
L2 Forwarding Engine


View 1 Replies View Related

Copyrights 2005-15, All rights reserved