Cisco Switching/Routing :: WS-X6748-GE-TX Change Module Cause Some Ports Of Server Offline

Dec 1, 2012

I have a server with 4 ethernet ports, 1G, they are bonded together, two of them was pluged into cat6500 module WS-X6724-TX. now we have moved the two ports to the replace module WS-X6748-GE-TX.
 
I have checked server side, the bond configuration are same no changed. what is possible reason replace module will cause link offline? why "sh run all" give the port is shutdown?

View 8 Replies


ADVERTISEMENT

Cisco Switching/Routing :: Getting Module WS-X6748-GE-TX PWRDown On 7606?

Jan 28, 2013

its a hardware problem or just not get power to module 1 for module WS-X6748-GE-TX? this is the capture from show module and sh log :
 
------------------ show module ------------------
  
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  1   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     xxx
  5    2  Route Switch Processor 720 (Active)    RSP720-3CXL-GE     xxx
Mod MAC addresses                       Hw    Fw           Sw           Status

[code].....

View 4 Replies View Related

Cisco Switching/Routing :: First 12 Ports Of X6748 TX Are Not Working

Aug 19, 2012

I have a cisco 6509 switch in which i have 2 SUPs. I am using 3 Qty. of WS-X6748-GE-TX in the same switch. First 24 ports of module 1 and are not working. I replace the faulty moldule with the working one but now the new (good) module's first 12 ports stopped working. But when I insert the good card (the replaced one with the faulty) in other chassis it works fine.

View 2 Replies View Related

Cisco Switching/Routing :: Enable All 4 10G Ports On WS-X45-Sup7-e Supervisor Module?

Dec 7, 2011

How do I enable ports 3 and 4 on this supervisor module?  I can only get ports 1 and 2 to work by default.  I have a standby Supervisor in SSO mode.  I'm running IOS 15.0.2SG

View 2 Replies View Related

Cisco Switching/Routing :: 6513 Moving LACP Ports To Another Module

Mar 20, 2012

I have a Cisco 6513 switches connected to HP VC Flex 10 Module.  The (2) 10Gb ports on a Cisco Switch connected to VC Flex-10 in LACP mode.
 
I need to move those (2) 10Gb ports on Cisco Switch 10Gb Module to a different 10Gb module on a same Switch without bringing the ports down since it is a live environment.
 
What I would do is to configure a same port channel ID on a new 10Gb module and then move port one by one. unplug one port and connect to the new port on a module. While I will be unplugging the first port the other active port will keep sending traffic and as soon as I plug in on another port, both ports will be active.

View 1 Replies View Related

Cisco Switching/Routing :: 4507R Cannot Put Command HW-Module To Change GE Port

May 3, 2013

i have 4507R with dual supervisors (WS-X4013+10GE) with IOS  cat4500-ipbasek9-mz.122-46.SG.bin the supervisor module are in 3 and 4, and I want to connection port 5, but i have interface and line protocol down "inactive" error.
 
So I realized to use command "hw-module" to change the module to GE port. However, I am not able to use the command as" I cannot use the command "hw-module uplink" as well.

View 2 Replies View Related

Cisco Switching/Routing :: Configuring 1941 With 8 Port EHWic Switch Module And Onboard GE Ports In Single LAN?

Jul 1, 2012

Can you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?

I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?

View 2 Replies View Related

Cisco Switching/Routing :: 3333 How To Change Ports To Access

Jan 28, 2013

how can I change the telnet port and ssh port for a different ones?? for example I´d like to change de default telnet port (23) for a 3333 it is possible??

View 9 Replies View Related

Cisco Switching/Routing :: WS-X6748-GE-TX And SUP-2T Compatibility?

May 13, 2013

I have a WS-X6748-GE-TX with the WS-F6700-CFC daughter card. Is it possible to replace the WS-F6700-CFC daughter card with a WS-F6K-DFC4-AXL to make this compatible with the SUP-2T? Or, are there differences between the CFC and DFC base modules?

View 11 Replies View Related

Cisco Switching/Routing :: VSS With VS-S720-10G-3C And WS-X6748-GE-TX Compatibility?

Feb 7, 2012

We are upgrading two standalone 6509E chassis to a VSS system with new VS-S720-10G-3C cards.  The 6509's have WS-X6748-GE-TX card with DFC3B daughter cards (see below).  The compatablity matrix (see below) states that 67xx cards are supported but it goes on to state DFC3C or DFC3CXL cards are needed.  So does this mean that the existing WS-X6748-GE-TX cards have to be upgraded or will they be supported? 

Core #1Mod Ports Card Type                              Model              Serial No.--- ----- -------------------------------------- ------------------ -----------  1   48  CEF720 48 port 1000mb SFP              WS-X6748-SFP       SAL  2    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE      SAD  5    2  Supervisor Engine 720 (Active)         WS-SUP720-3B       SAL  6    2  Supervisor Engine 720 (Hot)            WS-SUP720-3B       SAL  7   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL  8   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL

[code]....

View 3 Replies View Related

Cisco Switching/Routing :: X2 10GB SR10 Gig Module Will Support Fijutsu Primary Server

Jun 12, 2013

We got a requirement for 2 number of  X2-10GB-SR line card WS-X45-SUP6-E in WS-C4506-E.Customer want to connect with Fujitsu primary server . they have 10 gig module so i guess it will support with that.Also a doubt this X2-10GB-SR we can directly connect the firber sc multimode cable write no additional sfp required write .And for my knowledge if i use CVR-X2-SFP. I think to multimode sfp we have to insert write so do we get to 10 gig ports in one slot or how is it .

View 1 Replies View Related

Cisco Switching/Routing :: WS C3560E 12SD - Connect Server To Switch Through FC Cable With SPF Module

May 6, 2012

Recently I have faced following problem in my office, We have purchased two new Dell Server Power Edge R910 with built-in 10GB FC Network card. Service tag of this two servers are given bellow.
1. 7D94C2S
2. 6D94C2S
You can can Check specification of this two server from dell website{ URL}
 
We have two CISCO switch and model is given bellow:
Brand: CISCO
Model: WS-C3560E-12SD

We want to connect server to switch through FC cable and both switch have SPF module. But when we connect server to switch, link do not establish even switch and server port light become off.
Then we have tested the following things:
1. Connect server to server through FC cable, it is okay.
2. Connect switch to switch through same FC cable, it is okay.
 
I don't understand why it is not working.

View 5 Replies View Related

Cisco Switching/Routing :: To Replace A Line Card WS-X6748-SFP

Oct 18, 2012

I urgently want to replace a faulty line card WS-X6748-SFP with a new one. The switch concern is a 5609-V-E operating in Virtual Switching System mode.How long do you suggest the down time will be?

View 1 Replies View Related

Cisco Switching/Routing :: C6506-E / TestAclPermit Fail In WS-X6748-SFP?

Dec 7, 2011

in my C6506-E installed module WS-X6748-SFP with WS-F6700-DFC3BXL
 
last time a see errors:

18:42:49: %DIAG-SP-6-TEST_RUNNING: Module 3: Running TestAclPermit{ID=23} ...
18:42:51: %DIAG-SP-3-TEST_FAIL: Module 3: TestAclPermit{ID=23} has failed. Error code = 0x1
  23) TestAclPermit -------------------> F
 Current bootup diagnostic level: minimal
Module 3:
Overall Diagnostic Result for Module 3 : MINOR ERROR
Diagnostic level at card bootup: minimal

[code]...

View 4 Replies View Related

Cisco Switching/Routing :: IOS Level Support Required For WS-X6748-GE-TX?

Nov 21, 2012

currenly running a C6509E, with a WS-SUP720-3B running IOS level S72033-adventerprisek9_wan-MZ.122-22.SXH3.  I want to install a WS-X6748-GE-TX blade and would like NOT to have to upgrade IOS at this time.  Future migrations are planned.  Can this be done? 

View 6 Replies View Related

Cisco Switching/Routing :: 6500 Packet Loss On Blade WS-X6748-GE-TX

Oct 2, 2011

we have a 6509 with ios 12.2.33SXJ
 
we have 2 WS-X6516-GE-TX, WS-X6516A-GBIC, and a WS-X6748-GE-TX with a WS-F6700-CFC daughtercard
 
our sup is a WS-SUP720-3B
 
we are experiencing packet loss for everything connected in the WS-X6748-GE-TX blade, right now we dont have any production device in that blade due to the packet loss we are experiencing.
 
this switch was running hybrid  before it is now running native ios, however I can't recall if we didn't have that packet loss before. do i need to update a firmware of the card or daughtercard (if this is possible, can't say i've done it before).

View 10 Replies View Related

Cisco Switching/Routing :: 7606 Need To Install WS-X6748-GE-TX With WS-F6700-DFC3CXL

Nov 13, 2012

I have one Cisco 7606 and i need to install a WS-X6748-GE-TX with WS-F6700-DFC3CXL.When I install the WS-X6748-GE-TX the module is powered off with the following warning:
 
00:01:45: %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 1, power not allowed: Unsupported baseboard/earl combination. [code]

View 1 Replies View Related

Cisco Switching/Routing :: X6748 And NAM-2 Modules Inaccessible After Installing Linecard

Oct 8, 2012

I've installed second WS-X6748-SFP linecard on my catalyst 6509 with sup720-3b and after that NAM-2 and IDSM-2 module become inaccessible from management network. I can only login with session slot N proc 1.When I execute #hw-module module 4 reset, modules become accessible.
 
#sh module from cat6509
 
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  2   48  CEF720 48 port 1000mb SFP              WS-X6748-SFP       SAL114670XW
  3   48  48-port 100FX SFP Ethernet Module      WS-X6148-FE-SFP    SAL1201BZKF
  4   48  CEF720 48 port 1000mb SFP              WS-X6748-SFP       SAL1625ETFJ
  5    2  Supervisor Engine 720 (Active)         WS-SUP720-3B       SAL1206FNGQ
  6    2  Supervisor Engine 720 (Hot)            WS-SUP720-3B       SAL1206FVFB
  8    8  Intrusion Detection System             WS-SVC-IDSM-2      SAD120502LR
  9    8  Network Analysis Module                WS-SVC-NAM-2       SAD120206LB
 
Mod MAC addresses                       Hw    Fw           Sw           Status
--- ---------------------------------- ------ ------------ ------------ -------
  2  001e.4a3e.3b30 to 001e.4a3e.3b5f   1.10  12.2(14r)S5  12.2(18)SXF1 Ok
  3  001e.4aea.e7b0 to 001e.4aea.e7df   3.3   8.4(1)       8.5(0.46)RFW Ok
  4  5057.a895.bb84 to 5057.a895.bbb3   2.4   12.2(18r)S1  12.2(18)SXF1 Ok
  5  001c.58d0.6dc4 to 001c.58d0.6dc7   5.6   8.5(2)       12.2(18)SXF1 Ok
  6  0016.c848.3698 to 0016.c848.369b   5.6   8.5(2)       12.2(18)SXF1 Ok
  8  001e.f7a1.54b0 to 001e.f7a1.54b7   6.3   7.2(1)       7.0(8)E4     Ok
  9  001e.f72a.ba62 to 001e.f72a.ba69   4.3   7.2(1)       5.1(2)       Ok
 
Mod  Sub-Module                  Model              Serial       Hw     Status
---- --------------------------- ------------------ ----------- ------- -------
  2  Centralized Forwarding Card WS-F6700-CFC       SAL114881B6  4.0    Ok
  4  Centralized Forwarding Card WS-F6700-CFC       SAL1624EGQS  4.1    Ok
  5  Policy Feature Card 3       WS-F6K-PFC3B       SAL1206FNZY  2.3    Ok
  5  MSFC3 Daughterboard         WS-SUP720          SAL1206FSFH  3.1    Ok
  6  Policy Feature Card 3       WS-F6K-PFC3B       SAL1206FP27  2.3    Ok
  6  MSFC3 Daughterboard         WS-SUP720          SAL1206FN26  3.1    Ok
  8  IDS 2 accelerator board     WS-SVC-IDSUPG      ADBG7270048  2.5    Ok
 
cat6500 running 12.2(18)SXF12a ios...

View 8 Replies View Related

Cisco Switching/Routing :: Nexus 5k With L3 Card Showed Offline?

Aug 30, 2011

i have a nexus 5k with a l3 card i'm not able to bring online
 
NX-OS is:5.0(3)N2 (1)
L3 card is:L55D160L3
 
i inserted L3 module several time with the same resul...if i perform a show module i see the card offline. At the boot switch show an error message:
 
L3 module is down due to a BTCM down..

View 8 Replies View Related

Cisco Switching/Routing :: Nexus 5548 Fex Offline When Pre-Provisioning

May 9, 2013

I am setting up a new environment with 2 5548's and some 2248TP-1GE Fex's and Im running into an issue. I have the peer link and peer-keepalive link that appear to be good. When I configure the fex and vpc for the fex  manually on each switch without pre-provisioning the slot the fex comes online and everything appears to be good. I can see all the ineterfaces when doing a sh int br and the sh fex detail shows all good. When I do the exact same thing but pre-provision the slot the fex stays in an offline state. Ive tried disabling the port(s) connected to the fex while configuring everything then enabling them but same thing. [code]

View 5 Replies View Related

Cisco Switching/Routing :: 6513-E / 6513 And WS-X6748-GE-TX Compatibility

Oct 29, 2012

we have a chassis 6513-E and a module WS-X6748-GE-TX, I'd like to know if could I put this module in any slot, since the documentation from Cisco says that any slot from a chassis 6500-E Series can support this module. And then in the documentation of WS-X6748-GE-TX says that this module is not compatible in the slots 1-8 of the 6513 chassis, only from 9th to 13th slots, in those slots from the 6513-E we already have 4x WS-X6748-GE-TX, and we'd like to know if could we put the module in the rest of the slots. The 6513, and 6513-E is kind of confusing.

View 4 Replies View Related

Cisco Switching/Routing :: Suddenly 2960 D Series Switch Went Offline?

Mar 5, 2013

Suddenly my 2960 D series switch went offline and i founf the switch was not powering. I can't figure out the issue.

View 3 Replies View Related

Cisco Switching/Routing :: 6500 - Randomly Devices Will Drop Offline And Then Come Back

Aug 28, 2012

I have a network that has a pair of 6500 switches on either end, running HSRP. In between each 6500 are two to three ruggedcom switches. They are connected to each other and the 6500's by trunk ports in a straight line. The 6500's see each other as CDP neighbors, and the 6500's can see the rugged- com as LLDP neighbors (ruggedcom only supports LLDP).
 
The issue is that randomly devices on the ruggedcoms will drop offline and then come back. The problem is that the devices that drop offline are all in the same VLAN, so it appears like a virus -  i.e. one device drops off, then multiple. Eventually the HSRP starts flapping between the two 6500s and this causes havoc on the network.I'm almost to the point of taking a laptop and plugging it into one of the ruggedcom's to see traffic, but the issue is that the ruggedcoms are outside in cabinets that laptops shouldnt be exposed to.

View 2 Replies View Related

Windows Server 2008 - Online / Offline File Sync

Jan 24, 2012

Domain support with these operating systems seems to be hit and miss.I have 11 computers connected to a domain and I was wondering what the best way to back up the files on the workstations to the server would be. The server has a mirrored raid array and online backup as well. Just checking to see what the best way to do this would be. I am having trouble with the offline files sync / online files sync with these operating systems.

View 1 Replies View Related

Cisco Switching/Routing :: 3900 - Add On Module

Jun 10, 2013

i have a cisco router (3900 series) and a add on module (4 x 1 Gig port module). For some reason i cant seem to port channel them and cant do routing (can set an ip address on those ports). I can do port channel and routing on  on-board ports. Do i have to enable any commands to do this ?                   

View 3 Replies View Related

Cisco Switching/Routing :: N55 M16UP Module In Nx5548up

Jun 24, 2012

Was wondering if anyone has ever hot ADDED, not swapped, an expansion module in a 5548up.  Is a switch reboot required?I looked at the H/W install guide and it does not mention anything.

View 3 Replies View Related

Cisco Switching/Routing :: C6506 Module Cannot Be Detected

Dec 3, 2011

My C6506 USING ws-sup720-3B, i upgrade the IOS to the latest release of 12.2(33) SXJ1 IOS version. After upgrade and reload the machine got one module cannot be detect..WS-X6416-GE-MT, 16 port 1000mb MTRK ethernet module. The version of this are:

-HW 1.0
-FW 5.3 (1)1
-SW 8.5 (0.46) RFW
 
Question 1: Any tools available on cisco to check out the hardware/software compabiity feature?
 
Question 2: Any release note, compability matrix table etc resources.

View 1 Replies View Related

Cisco Switching/Routing :: Module N7K-M148GS-11 Was Frozen?

Sep 4, 2012

Recently we ha a Nexus 7010 with a module frozen that was OIR (Online Remote and Insert) but do not work until reload the Nexus 7k.The command "show tech-support" has the following:
 
exception information --- exception instance 64 ----
Module Slot Number: 1
Device id : 147
Device Name: 0x93
Device Errorcode: 0x9329201

[code].....
 
Was is Excessive Interrupt Events? Can this "Minor Error" frozen the system?Is the port 42 on module 1 affected? o was 42 ports?

View 2 Replies View Related

Cisco Switching/Routing :: Encryption Module For 3845

Jun 25, 2012

Can the encryption module (DES/ 3DES/AES/SSL VPN Encrytion/compression) for Cisco Router 3845 able to support the external connection from other high end router, for example cisco 7200? What is the maximum bandwidth, load and concurrent connection it can support?

View 1 Replies View Related

Cisco Switching/Routing :: Put WS-X4712-SFP+E Module Into R-E Chassis?

Feb 3, 2013

why is not possible to put a WS-X4712-SFP+E - module into an R-E chassis?The module has the same connection to backplane as the WS-X4748-UPOE+E and this one works in a R-E chassis.I know the restriction of Cisco that the 4712 is only supported in 4503-E, 4506-E,4507+E and 4510+E, but why?Are there hardware-restrictions, is the backplane different?

View 2 Replies View Related

Cisco Switching/Routing :: 6509-E / IOS Requirements For VSS And ACE Module?

Sep 10, 2012

I have a pair of 6509-E Switches running VS-720 Supervisors. We are planning to add Ace Module onto the 6509-E. Will IP Base Image suffice the requirement? Will Ace Module work with only IP Base Image?

View 1 Replies View Related

Cisco Switching/Routing :: Hot Add - N55 M16UP Module In NX5548up?

Dec 16, 2012

Hot ADDED, not swapped, an expansion module in a 5548up.  Is a switch reboot required?

View 2 Replies View Related

Cisco Switching/Routing :: WS-X4606-X2-E Module Is Hot Swappable Or Not

Jan 6, 2013

Do you have any document that states whether WS-X4606-X2-E module is hot swappable or not?

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved