Cisco WAN :: 7600 - QoS On Sup720?

Oct 16, 2012

I have a strange QoS problem with one Cisco7600 (sup7203BXL, IOS 12.2(33)SRE6).
 
This is layer 2 traffic,and all ports are L2 dot1q trunks:
 
1) Packet comes with DSCP 46 on Gigabit port (WS6728-SFP) with "mls qos trust dscp" configured. It goes out the port of the same card/slot with DSCP 0.
 
2) packet comes with DSCP 46 on different Gigabit port on the same card/slot with "mls qos trust dscp" and also "mls qos vlan-based" configured. It qoes out out the port with DSCP 46.
 
Why the switch behave differently if "mls qos vlan-based" is configured on port (or to say it works correct since it doesn't override DSCP)?
 
I have global command "mls qos rewrite ip dscp" since this 7600 is also MPLS PE router and I found in documentation that "mls qos rewite ip dscp" is mandatory for QoS on MPLS (EXP bits). So I can't turn off "rewrite ip dscp". Again the problem that I presents is L2 problem not MPLS (MPLS is used for different traffic).
 
Also mls qos mappings are ok COS to DSCp are 5 to 46 and vice versa.
 
Furthermore, as far as I know if I have configured "mls qos trust dscp" on Gigabit ethernet port, switch (7600) should work in this order:

- make internal DSCP from packet DSCP

- since I don't have configured DSCP mutation DSCP should stay the same (46)

- using map DSCP - COS ( 46 -5 ) switch will choose queue on outgoing interface in regards to mapped COS

View 0 Replies


ADVERTISEMENT

Cisco WAN :: BGP Flapping After Upgrading 7600-SUP720 To 12.2(33)-SRD8?

Jan 23, 2013

We have a Cisco 7600 Router with SUP720/MFSC3 that was running version 12.3(33)-SRC3 for more than 2 years now. We recently had to upgrade to a newer release to solve a bug issue after recommendations, so we chose to go to SRD8 release. Since then we are facing a rather strange problem with one of my peer ebpg. we have 2-3 peering on the same router. only one of them is affected. The ebp keeps flapping every 3 minutes due to hold down timers.
 
12:14:33: %BGP-5-ADJCHANGE: neighbor 15.14.11.18 Down BGP Notification sent
12:14:33: %BGP-3-NOTIFICATION: sent to neighbor 15.14.11.18 4/0 (hold time expired) 0 bytes
12:14:33: %BGP_SESSION-5-ADJCHANGE: neighbor 15.14.11.18 IPv4 Unicast topology base removed from session  BGP Notification sent
12:14:47: %BGP-5-ADJCHANGE: neighbor 15.14.11.18 Up

[code]....
 
We asked our peer if they have similar problems but it seems they do not. Our peer is using Cisco 12810 running  12.0(32)SY11 After downgrading back to version 12.2(33)SRC3 again, the probem was fixed...

View 2 Replies View Related

Cisco VPN :: 6500 Sup720-3B SPA IOS SXI - GRE Tunnel Will Not Come Up

Apr 26, 2011

Cisco 6500 Sup720-3B SPA IOS SXI  - GRE tunnel will not come up.It worked fine on SXF code, but the crypto map can not be applied on tunnel interface.The iskmp is up with the OM_IDLE The crypto give it a Cryto UP, the the Tunnel does not come up.  It is UP down.Does some one have a working config with a 6500 IOS SXI Train with GRE IPSEC Tunnel?

View 1 Replies View Related

Cisco WAN :: SUP720 / GRE Traffic Which Is Not Processed In CEF?

Jan 10, 2008

we have some problem with GRE traffic which is processed by CPU and not by CEF.In sniffed packets I can see a lot of "TCP window update" packets.  I found that some kind of GRE traffic are forwarded to CPU, like packets with IP options or TTL=0 but non of those are seen in the sniffed packets.

View 2 Replies View Related

Cisco :: Sup720 - Supported Slots On A 6513?

Nov 28, 2011

Can the sup720b be used in any other slot on a 6513 besides 7 and 8?

View 1 Replies View Related

Cisco WAN :: SUP720-3BXL / Using Of ECC Or Plain Memory?

Dec 7, 2010

i know that Sup720-3BXL has been used the SDRAM.but i don't know that which of memory? using of ECC or plain memory?if use the plain SDRAM, how can prevent to parity error?

View 1 Replies View Related

Cisco Application :: 6509-E SUP720 And SLB Limitations?

Mar 21, 2012

We are looking into replacing our current Windows NLB configuration with a SLB solution as NLB creates some nasty multicast traffic.
 
We are currently curious about the limitations for running SLB without a dedicated ACE Module, will it handle line-rate speed (1 and 10 gbit) with SLB?
 
Does VSS introduce any limitations for SLB? Any other pitfalls/limitations we should be aware of?
 
Hardware info: 2x WS-C6509-E in VSS with VS-S720-10G (VS-F6K-PFC3C) running s72033-ipservicesk9_wan-mz.122-33.SXI7

View 1 Replies View Related

Cisco Switching/Routing :: How Many Session Can Use In Sup720-3b

Aug 30, 2012

I will use function of span in sup70-3b.How many session can use in sup720-3b? For example, 2 or 4 session.

View 1 Replies View Related

Cisco WAN :: Migrating Sup720 Configuration To Sup2T?

Jul 4, 2012

migration of an existing Sup720 configuration to a new Sup2T. At present we have a Sup2T chassis in the lab running 15.0(1)SY1 and a production Sup720 chassis running 12.2(33)SXI5.I've taken a copy of the production startup-config, renamed it to 'startup-config-BGFL_6509_MBAS-020712' and copied it to the bootdisk (and slave bootdisk) of the new Sup2Ts.I've then added the command 'boot config bootdisk:startup-config-BGFL_6509_MBAS-020712' in an attempt to boot from that config and have the Sup2T migrate it to the new config standards (particularly from a QoS perspective as mentioned here :[URL]
 
!
boot-start-marker
boot system flash bootflash:s2t54-advipservicesk9-mz.SPA.150-1.SY1.bin
boot config bootdisk:startup-config-BGFL_6509_MBAS-020712
...
Router#sh bootvar
BOOT variable = bootflash:s2t54-advipservicesk9-mz.SPA.150-1.SY1.bin,1;

[code]....

View 5 Replies View Related

Cisco WAN :: WS-SUP720-3BXL And WS-X6748-GE-TX Configuration

Feb 20, 2013

I have the above config in a 6509-E chassis with X2 Cac-3000 psu's
 
The problem i'm having is when everything is powered up it runs fine for about 10minutes then reloads the switch,The 6748 has a 6700-CFC installed the only way i have managed to get it run without crashes is to remove the 3BXL card from the sup and replace it with a PFC-3B, whilst this has solved the problem the client wants the 3BXL card to be installed, am I right in thinking that the CFC installed on the 6748 is incompatible with the 3BXL or maybe the 3BXL is faulty

View 4 Replies View Related

Cisco Switching/Routing :: Need To Know Serial Number Of Sup720

Dec 10, 2011

How can i find the serial number of sup-720 which is totally dead and not boot?By which sticker on SUP and where ? How many digits ?

View 4 Replies View Related

Cisco Switching/Routing :: Sup720-3BXL Stuck On SP

Mar 19, 2013

I have a SUP720-3BXL that will not boot. It will get stuck at booting from the SP. It never switches over to the RP.  [code]

View 5 Replies View Related

Cisco Switching/Routing :: SUP720-3B Internal Flash

Dec 1, 2011

I have received a sup720-3B from Cisco with an internal 512MB flash(sup-bootdisk). I want to verify what IOS image is on the disk and do not have an spare 6509 chasis. Can I remove the 512 MB flash disk and insert it to my disk0: on my production 6509 with the sup32 that the 720 will repplace and view what is on the disk without corrupting?

View 7 Replies View Related

Cisco WAN :: How Many BGP Routes WS-SUP720-BASE Engine Can Handle

Jan 6, 2011

to the above question. I see the specs for the WS-SUP720-3B and 3BXL but not the WS-SUP720-BASE with the MSFC3 and PFC3A daughter cards.The 3B can handle 256,000 routes using IPv4 and the 3BXL can do 1,000,000.

View 4 Replies View Related

Cisco Switching/Routing :: MLS Statistics On Cat 6500 With Sup720

Sep 11, 2012

when using "show mls statistics" I see a lot packets are getting L3 Processed. Does that mean they are getting software-forwarded?

IOS is 12.2(33)SXI5. 
Cat6k#show mls statistics
Statistics for Earl in Module 5
L2 Forwarding Engine

[Code]....

View 1 Replies View Related

Cisco WAN :: Sup720-10G 6509 - Multicasting In Same Vlan Broken

Oct 9, 2011

Currently we do not have multicat routing enabled on either of our 2x Sup720-10G 6509 Switches.  We have no intention of doing so either.  I am looking for clarification on how mutlicasting operates within a Vlan. 
 
IOS: s72033-ipservicesk9_wan-mz.122-33.SXH2a.bin
 
Our Vlan has IGMP snooping enabled.  Here is the output.
 
6509Switch#sh ip igmp inter vlan 25
Vlan25 is up, line protocol is up
  Internet address is 10.1.1.254/24
  IGMP is disabled on interface
 
we do not want to disable IGMP due to this one concern that I can't find documented. If we disable IGMP snooping on the vlan, what happens to multicast packets with a TTL > 1.  Do they get flooded to the entire switch and all Vlans?  Or does it stay within the Vlan? 

View 2 Replies View Related

Cisco Switching/Routing :: Downgrading IOS On Sup720 VS-S720-10G?

Oct 26, 2011

I got a new VS-S720-10G it had 122-33.SXH8b on there. I had to downgrade it to 12.2.33.SXI1 to match our other switches. I installed the file I use in all the other switches, s72033-adventerprisek9_wan-mz.122-33.SXI1.bin but the Sup is now is only booting up only to ROMMON mode.
 
Initializing ATA monitor library...
 
Self extracting the image... [OK]
Self decompressing the image : #################################################
################################################################################
################################################################ [OK]
 
 %SYSTEM-1-INITFAIL: Network boot is not supported.
  
System Bootstrap, Version 8.5(4)
Copyright (c) 1994-2009 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory

[code]....
 
How do I get the older version of IOS to load up?

View 5 Replies View Related

Cisco Application :: WS-SUP720-3B SP DRAM Requirement For ACE30

Oct 28, 2011

Last month I was reviewing following Cisco document, in which Cisco mentioned that ""To avoid possible memory fragmentation in the forwarding information base (FIB), Cisco recommends that the switch processor (SP) DRAM to a minimum of 1 GB ""
 
[URL] 
 
Since this document has been revised in Oct 2011 and, I can't no more find the above memory recommendations.
 
I want know if any one using WS-SUP720-3B with IOS SXI6 and Cisco ACE30 has gone for upgrading the SP DRAM from 512MB(default) to 1GB ?

View 1 Replies View Related

Cisco WAN :: 7613 - Redundancy With WS-SUP720-3BXL Module

Mar 20, 2012

We have Router CISCO7613,SSO redundancy configured with two Sup 720-3BXL running 12.2(33)SRC1 image. Even thought I've configured SSO, my standby sup remains in COLD state with the following logs generated.
 
Mar 20 22:07:32.514 IST: %ISSU-SP-3-PEER_IMAGE_INCOMPATIBLE: Peer image (c7600s72033_sp-ADVENTERPRISEK9-M), version (12.2(33)SRC1) on peer uid (8) is incompatible
Mar 20 22:07:32.514 IST: %ISSU-SP-3-PEER_IMAGE_INCOMPATIBLE: Peer image (c7600s72033_sp-ADVENTERPRISEK9-M), version (12.2(33)SRC1) on peer uid (8) is incompatible
Mar 20 22:08:48.263 IST: %PFREDUN-SP-4-INCOMPATIBLE: Defaulting to RPR mode (Runtime incompatible)
[code]... 

These logs says that due to some reasons, the configuration is not being synchronized with active and standby sups and hence the redundancy mode remains in RPR mode and SSO not achieved, and hence COLD state. However, I couldn't find a reason why the configuration is not being synchronized, I've issued the command, redundancy config-sync ignore mismatched-commands, and everything worked fine, SSO achieved and standby sup came to HOT state.Now my query is, 

1. Why the configuration was not synchronized and standby SUP got in COLD state??
2. Since I issued the suggested command, at least, some of the mismatched lines in configuration will be ignored, Will that create a problem when my Active sup fails and standby become active?

View 4 Replies View Related

Cisco Switching/Routing :: 6500 - Replace Sup720 In VSS

Nov 16, 2011

I have problem with the standby supervisor in 6500 vss and need to replace the supervisor.  I have follow how-to on the cisco web site url...
 
But when i boot the new standby sup720 it comes active and both supervisors is rebooting.  I wonder if i can do the replacement without rebooting both active and standy supervisor.

View 1 Replies View Related

AAA/Identity/Nac :: SUP720 ISE Supported Switch IOS Version

Apr 18, 2012

The table referenced in the new 1.1 ISE guide show 12.2(33)SXI6 is the minimum version for support. Does this mean this version or above? Does ISE is tested in newer SXJ streams? We have a massive rollout of SUP720s to do and need to know the most stable version to load in preparation for ISE.

View 1 Replies View Related

Cisco Security :: Change Default SSH Port On Cat 6500 WS-SUP720-3B?

Jul 17, 2011

I have been net searching this question and I find answers relative to other Cisco products but not for the 6500 series. We are running entservicesk9_wan-mz.122-18.SXF17a.bin and would like to know how to change the default SSH listening port..

View 1 Replies View Related

Cisco Switching/Routing :: 6509E - Installing And Setting Up Second Sup720

Feb 27, 2013

Trying to find documentation on the proper procedure for installing a second sup720 into our 6509-E chassis for sup redundancy. I have found documents that tout how 'cool' and 'awesome' NSF/SSO, and all that is, but haven't found any docs on installing a second sup720 into a chassis that is currently in production and is only running one sup720. In all the years that this chassis has been out, there must me a documented procedure out here to explain this.I have been through the following pages, and have found nothing to this effect.

View 1 Replies View Related

Cisco Switching/Routing :: Configuring MWAM With Sup720-3B In 6506-E?

Nov 29, 2011

problem to configure MWAM. I have installed MWAM module in 6506-E slot 2 with sup720-3B. After installing MWAM the Status is PwrDown. I tried to turn on the power but its not happening. MWAM is installed in slot 2 and here is the result of show module 2 My Sup720-eB IOS image is s72033-advipservicesk9_wan-mz.122-33.SXJ1.bin
  
6506-E#show module 2
 Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  2    3  MWAM Module                            WS-SVC-MWAM-1      SAD081203GK
 Mod MAC addresses                       Hw    Fw           Sw           Status
--- ---------------------------------- ------ ------------ ------------ -------
  2  0003.feae.bb8c to 0003.feae.bb93   3.0   Unknown      Unknown      PwrDown
 Mod  Online Diag Status
---- -------------------
  2  Not Applicable

View 2 Replies View Related

Cisco WAN :: Cat 6500 IOS Upgrade - Installing Secondary SUP720 In 6509-E

Nov 21, 2011

I will be installing a secondary SUP720 in a 6509-E and will be upgrading the IOS on the existing SUP which is on  122-18.SXF6. I've read that this release has passed End of Critical Maintenance earlier this you. I thinking of upgrading the IOS to 12.2.33-SXJ1(ED) or 12.2.33-SXI8(ED) (possible more stable), but i'm not sure if i need any step upgrades from the current version. The SUP meets the required hardware specs and I will also be upgrading the ROMMON to 12.2(17r)SX7 first.
 
I have alot of experience upgrading IOS on routers and switches, but i just need to now if there are any gotchas that i need to know for the upgrade on the SUP.
 
The other issue is i don't believe the current IOS has been installed, are there any issue running on an IOS not installed. Patching is not available since the system is not running from an installed image. To install please use the "install file" command.

View 3 Replies View Related

Cisco Switching/Routing :: 6513E What Current IOS Version Should Run On Sup720

Jan 23, 2012

We are close to receiving our new 6513E chassis which I will be running Sup720 cards in. This will be replacing our existing 6509 Sup2 setup in production. What current IOS version should I run on the Sup720 ? I would like to support SSH. The chassis will be populated with a couple of 6724 SFP cards, 2 6704 10 gig cards and a few 6748 line cards.Is there a good intitial config guide ?

View 6 Replies View Related

Cisco Switching/Routing :: SUP720 - Unable To Boot From Disk0

May 26, 2012

Customer is using SUP720 with SP rommon image version 8.1(3), he is trying to boot the new ios image from disk0, but he gets invalid magic error. he fomat the disk0 but still he gets error when he boots from disk0. He suspect that it can't be flash problem but can be software of hardware as he has two flash with same issue on 2 switches.
 
Customer wanted to recreate, I tried in the lab, i was able to load from disk0, but sup in lab had 8.5(4).
 
Customer wanted me try with 8.1(3) version. But i was unable to downgrade the SP Rommon image. SP rommon is running in Gold region and I loaded the 8.1(3) from both disk0 and sup-bootdisk, even preferrence was given to region1 but still sup came up with gold region itself.

* Will i be able to downgrade from 8.5(4) to 8.1(3), if so, what are the steps.

* is there any limitation or bug where  8.1(3) will be unable to read disk0.

View 4 Replies View Related

Cisco Switching/Routing :: 6509 - Maximum ARP Entries On Sup720?

Jan 13, 2008

Just a very quick one.  Is there any physical limitation to how many ARP entries a 6509 and sup720 can have?

View 4 Replies View Related

Cisco Switching/Routing :: 6500 With SUP720 Recovery From ROMmon

Jan 24, 2007

if it is possible to recover a Cat 6500 that has no code on bootflash from ROMMON, and is it mandatory to have a compact flash card to do the recovery ? or can one use xmodem or TFTP ?

View 6 Replies View Related

Cisco Switching/Routing :: 6506E - Sup720 BootVar Not Shown

Jun 4, 2013

I'm trying to boot this IOS on a 6506-E, s72033-adventerprisek9_wan-mz.122-33.SXI8.bin.
 
This is what I see in bootvar.
 
sh bootvar
BOOT variable = disk0:s72033-adventerprisek9_wan-mz.122-33.SXI8.bin,1;disk0:s72033-ipservicesk9-mz.122-18.SXF8.bin,1;
CONFIG_FILE variable =
BOOTLDR variable =
Configuration register is 0x2102
 
Standby not ready to show bootvar, I want to remove SXF8 and leave SXI8 alone. I removed both IOS file names in boot system and added the SXI8 again and saved. So this would be the output after.
 
But after a switch restart, this would be the output of show bootvar again.
 
sh bootvar
BOOT variable = disk0:s72033-adventerprisek9_wan-mz.122-33.SXI8.bin,1;disk0:s72033-ipservicesk9-mz.122-18.SXF8.bin,1;
CONFIG_FILE variable =
BOOTLDR variable =
Configuration register is 0x2102
 
Is there anything I need to check? This is an old engine and I'm not sure if the variables of the RP modified .

View 12 Replies View Related

Cisco Switching/Routing :: Safe Harbor Versus Sup720

Mar 11, 2012

Cisco Safe harbor, I came nto know this can be a replacement for Sup 720.

View 2 Replies View Related

Cisco Wireless :: 6500 - Why WiSM2 Not Recommended In SUP720 Slots

Jun 27, 2012

I have a situation where a customer doesn't have the required power units installed in their 6500 for me to provision a WiSM2.They use a VSS pair with a single Sup720 in each. They have no intention of adding a second Sup to each chassis.

I need to justify why they can't use slot 6 (which has power reserved) if I am to get them to upgrade the PSU's. The documentation I've found says it is supported but not recommended.

View 1 Replies View Related

Cisco :: Configure Netflow Catalyst 6500 With SUP720-10GE

Jun 5, 2012

I tried to configure netflow without success.
 
Setup is the following.
 
Cisco Catalyst 6509 with Sup720-10GE IOS 12.2(33)SHX7. There are around 30 L3 vlans configured on the switch. I'm only interested for the traffic on one L3 vlan which is the connection to wan cloud.
 
I wanna see only the traffic that goes to and come from the wan. On other Catalyst where I have routed interfaces i successfully configured netflow. I read a lot in the forums and documentations but i didn't find the right one.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved