Cisco WAN :: C1812 Possible To Copy IOS Image From Flash Of One Router And Use It To Upgrade Another
Jun 19, 2012
I have two Routers (C1812 & C1841) each having different version of IOS images. I was wondering if its possible to copy IOS image from flash of one Router and use it to upgrade another.
View 2 Replies
ADVERTISEMENT
Jul 19, 2011
I am using TFTPD32 to upgrade the IOS on a router. When I type in the commands copy tftp flash and enter all the necessary information, the router sits for a minute or so and then times out. There is no entry made in the log when it times out. copy flash tftp yields the same result. The fa 0/0 interface and the TFTP server are both on the same subnet and can successfully ping one anothe
View 16 Replies
View Related
Feb 26, 2012
Trying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
View 1 Replies
View Related
Mar 11, 2012
I am sitting on Internet and want to copy IOS Image to router. I can SCP, itu authenticated to Router but ends with a message "host is not communicating for more than 15 seconds".
Router : Cisco 2821
Current IOS: (C2800NM-ADVENTERPRISEK9-M), Version 12.4(24)T1.
View 3 Replies
View Related
Feb 6, 2011
When I try to copy ios to one flash in router 2801, I receive the message of of insufficient memory, and have the follow out in the next command: [code] This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.
View 6 Replies
View Related
Jul 7, 2011
How do I save/copy all of the router configuration entries onto a memory/flash usb drive? I did not configure the router myself (out of town when purchased). I have already downloaded the manual for that router and I want to understand exactly what she (person who configured router) did and identify any mistakes she might have made. Once downloaded, I assume I can print out all configuration settings.
View 3 Replies
View Related
Oct 3, 2012
I have Cisco 2600 series Router which has only 32 MB flash memory. I tried to load IOS image in that but image size is 29 Mb in compressed form. The minimum i found is 5 MB in compressed form but it is missing so many commands. that in 32 MB flash, how can I load image which has almost all the commands.
View 3 Replies
View Related
Jan 8, 2013
I just got a brand new ASA 5550, i configured the port g0/0 on asa with an ip address 192.168.10.1 then configure my computer with ip 192.168.10.2 and default gateway is 192.168.10.1. I'm able to ping the asa from my computer. I remote to ASA thru the console port and try to copy iOS from flash to my pc but it doesn't work.
Cisco asa# copy flash tftp://192.168.10.2/asa804-k8.bin
Source file name []? asa804-k8.bin
Address or name of remote host [192.168.10.2]?
Destination file name [asa804-k8.bin]?
Writing file tftp://192.168.10.2/asa804-k8.bin...
!%Error writing tftp://192.168.10.2/asa804-k8.bin (Timed out attempting to connect)
Cisco asa#
View 3 Replies
View Related
Feb 24, 2012
I have a really stupid problem with my RV042. The main logon password has expired but it will not let me change it at all. Basically I try to login but get the error 'The old password has expired. Please change the password'. But with no prompt at all for a new password and just a return to the login page. Tried various different browsers, tried the old default password but nothing will work. There seems to be no way of changing it and I cannot login.Am I missing something glaringly obvious? I really don't want to reset it to default as I have numerous VPN tunnels configured and various other settings.
View 2 Replies
View Related
Feb 20, 2012
I have a 3550 switch that I am trying to upgrade the IOS on.I am trying to copy to a TFTP server.I am receiving a socket error. [code]
View 3 Replies
View Related
Nov 9, 2011
Is it possible to use the USB ports on a ASA5510's to copy files onto the flash?
I have not been able to find any ionfo on this in the users guides ?
View 2 Replies
View Related
Jul 9, 2012
I am trying to research the possiblity of backing up IOS and configurations from an Etherswitch module, and being able to store the files onto the Host Router's flash (3925 ISR). and then being able to recover that IOS and configuration, in case I have to replace the Etherswitch Module.
View 4 Replies
View Related
May 2, 2013
how to copy a cisco ios image from a 3750 to my pc so that i can use it to upgrade a switch on my desk.
View 3 Replies
View Related
Jul 27, 2011
I m unable to take backup of Switch c2960 using
#Copy flash: tftp
while i m taking it show some error
t#copy flash: tftp:
Source filename []? c2960-lanbasek9-mz.122-44.SE6
Address or name of remote host []? 10.23.120.15
Destination file name [c2960-lanbasek9-mz.122-44.SE6]?
%Error reading flash:c2960-lanbasek9-mz.122-44.SE6(Is a directory)
sh flash:
Directory of flash:/
2 -rwx 1919 Mar 1 1993 10:27:17 +05:30 private-config.text
3 -rwx 11056 Mar 1 1993 10:27:17 +05:30 config.text
4 -rwx 804 Mar 1 1993 05:30:42 +05:30 vlan.dat
6 -rwx 2072 Mar 1 1993 10:27:17 +05:30 multiple-fs
7 drwx 192 Mar 1 1993 05:37:02 +05:30 c2960-lanbasek9-mz.122-44.
SE6
View 1 Replies
View Related
Feb 20, 2012
I have a 3550 switch that I am trying to upgrade the IOS on.I am trying to copy to a TFTP server.I am receiving a socket error.I saw that this can be fixed with
Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#no service config
Switch(config)#exit
Switch#
00:13:47: %SYS-5-CONFIG_I: Configured from console by console
Switch#reload
I have done this 3 times to no avail.My TFTPd32 server on my pc is working fine.Here is the error
Switch#sh flas
Directory of flash:/
2 -rwx 556 Mar 1 1993 00:33:53 +00:00 vlan.dat
4 -rwx 3775 Mar 1 1993 00:37:54 +00:00 config.text
5 -rwx 24 Mar 1 1993 00:37:54 +00:00 private-config.text
6 -rwx 5687963 Mar 16 2007 01:05:23 +00:00 c3550-ipbasek9-mz.122-25.SEB4.bin
8 drwx 192 Mar 1 1993 00:04:40 +00:00 c3550-i9q3l2-mz.121-22.EA1a
[code]......
View 14 Replies
View Related
Jun 12, 2012
I want to copy a file from one ASR1001 and copy it to another. I ntried using tftp 32 but this is not going to work as the image is 315 MB.
how to copy an image from one router directly to another router's flash, if possible?
View 5 Replies
View Related
Dec 7, 2011
I am trying to configure a switch that was given to me. They don't know the password to anything. I have already tried to recover it. The problem is, the switch doesn't load flash, or will copy flash from xmodem either. It also doesnt load the helper or boot. It is user mode and lets me do nothing. It doesnt let me use the enable command to get into it. I would like to start the config from scratch. Its a 3500xl switch, 24 ports. I dont know what to do with it. I am trying to study for my CCENT Exam and would like a switch that worked.
View 8 Replies
View Related
Oct 5, 2010
I have a cisco 3750 swicth which i want to load a new ios to but unfortunately there's no enough space on the flash. This means that i need to backup the cureent (old) ios to my tftp server but the command keeps failing. It always gives 'No such file or directory' error .The free space on the flash is 8mb and my new ios is about 11mb.I also went inside the directory where the old is and inputed the same copy command but to no avail.Below are some of the command failure on the swicth:
[code]....
View 25 Replies
View Related
Feb 22, 2012
I recently posted this same issue the other day, using TFTPd32. Now i am pretty close to fixing it. I do have a different setup; my pc ethernet port is broken so I am using an ethernet/usb adapter. I am attempting to backup my IOS from a 3550 switch to my PC.
This is the error I am getting. Code...
View 5 Replies
View Related
Dec 22, 2012
I purchased a used AIR BR1310G-A--K9-R from a local high school that was rebuilding their athletic field. The AP was used for communications for their pressbox staff. The AIR BR1310G was part of the schools campus wide WiFi network and was upgraded to an lwapp image c1310-k9w8-m 12.4 3c JA. Our home sits on a large lot and I would like to convert the BR1310G back to an autonomous AP.
In order convert it back to an automonous AP, I will need the original image. The school used a contractor for their WiFi network and they do not have a backup of the original image. I do not have a service account with Cisco so downloading the autonomous image from the Cisco website is out. What are my options for either obtaining an image file or using the current managed image without a WLC?
View 0 Replies
View Related
Jun 23, 2011
I have a PIX 501 and I am looking to download an OS as my current image is corrupt and the PIX will not boot. Where I can download the O/S from so I can tftp it across to the router.
View 1 Replies
View Related
Sep 15, 2012
I have a cisco 2821 Router , it was operating fine but for the past 2 days its having a weird problem.During operation suddenly the connection is lost and when checked through console there is no IOS image on the Router (all configuration is erased and the router boots up in rommon mode and there is no IOS on dir Flash:I installed ios on it through tftp but again after some random time the IOS is automatically erased from flash i checked the config register value and its fine at 0x2102.
View 5 Replies
View Related
Oct 24, 2012
I have a Cisco 7204 vxr router that does not have a valid image on the boot flash or on the pcmcia card (disk 2). I tried everything i could to try and get the router to recognize the flash but it keeps giving me a magic card error. I'm losing my mind slowly but surely.
The router boots into Rommon every time and the Rommon options for this router are horrible. No tftpdnld option. Can I get this router to boot from tftp, from Rommon?
View 1 Replies
View Related
Jul 14, 2012
I need to upgrade compact flash memory card for a 3800 router. Basically i want to upgrade code on this router and the current flash size (64Mb) cannot hold new image. I wanted to check if i swap the old flash (64 Mb) with a new one 256 mb, i will loose vlan.dat file since it's stored in flash. Is there a way i can copy vlan.dat to new flash which has new code before i change the boot statements and reload the router?
View 1 Replies
View Related
Nov 1, 2011
I have an ASA 5520, currently running version 7.25-k8. I'm preparing for an upgrade to version 7.25(4), so I transferred the software code (obtained via Cisco download) to the firewall vis SCP. I then issued the "verify flash:asa725-k8.bin" and it fails. It comes back with the error that the CRC did not verify, Data Integrity has been compromised". My first thought was the image did not copy correctly, so I deleted it and transferred it again. I got the same error. Then I decided to run a verify against the actual current code that was running on the firewall, and it came back with the same error. I don't understand what the problem is. I don't tend to think it's an SSH key related problem, as the method I use to access the firewall is via SSH and I have no problems. Worth noting,this firewall is part of an active/standby pair, and I observe the same behavior on the failover unit, it fails to verify.
View 3 Replies
View Related
Sep 3, 2012
I am doining a flsh upgrade for 12000 router ... I am following this guidelines
[URL]
when i do show version | i image System image file is "disk0:c12k-os-mbi-3.6.0.CSCsy28524-1.0.0/mbiprp-rp.vm"
but at doc it says : System image file is "disk0:c12k-os-mbi-3.6.0/mbiprp-rp.vm" i think my image has something wrong. what do you say ? actually from step 1 to 16 was going smoothly , but step 17 doesnt go ... and i jump to Flash Disk Upgrade Abort Procedure section and i rollback to old flash disk and now it is working ....
Regarding to step 17, why standby PRP is not ready , it shows no valid partner ?
View 7 Replies
View Related
Jan 6, 2013
I've had occasional issues with 5505 upgrades going south when the boot hangs on the image load due to a corrupt image. I need a way to validate the checksum of the new image after it is copied to flash. Remote upgrades become a real pain when you have to go onside just to delete an image, copy it into flash again, and boot.
View 1 Replies
View Related
May 1, 2012
I am going to get some wyse thin clients up and running on our departments. Each department communicate with the main-office through Cisco C1812 routers.
In order to get functionally DHCP up and running, I need to
A - Configure some Dhcp options on the C1812 routers
B - Perform a DHCP relay from each department to the main-office
Option B will cause some additional issues, so is not preferred.
The question is: Does the Cisco DHCP-client have an option for configuring DHCP options? I need to put in among others, an option 161, a string value pointing to a ftp-server. Can this be done? And if it can, what is the right syntax
I have recently started working here, therefore I am not certain of the IOS-version on the router, as I still not have the logon-information, but I will aqquire this shortly.
View 4 Replies
View Related
Aug 16, 2011
I was trying to upgrade from 8.3.1 to 8.3.2. but I am unable to copy via tftp to the ASA flash or disk0:
ASA5520# copy tftp: flash:
Address or name of remote host []? 10.88.127.153
Source filename []? asa831-k8.bin
Destination filename [asa831-k8.bin]?
[code]....
Half way thru writing to the disk, it goes for a reboot. There is more than enought space on the disk0. I tried copying via a Compact Flash, but the ASA is not detecting the Compact Flash (which I thinks should be disk1). I tried copying a asdm file, even that also went for a reboot.I am stuck now, unable to upgrade
View 12 Replies
View Related
Feb 25, 2012
Currently I have C2801 with 256MB of memory and 64MB of flash. I want to upgrade it to 384MB / 128MB.Do I need to get MEM2801-256D or I can use any PC133 SDRAM (144PIN) for memory? 384 is maximum I can install? Do I need to get MEM1800-128CF or I can use any compant flash card? 128MB is maximum I can install? (I saw 256MB flash on for C2801)
View 10 Replies
View Related
Sep 25, 2012
I need to upgrade the compact flash memory on a 2821 router from 64 to 128, upgrade the ios, and re-script the router. So I'm wondering what is the correct sequence? With the router powered on, do i eject the existing flash, and install the new one or do I power down the router? Once the memory has been increased, then i can upload the new ios?
View 1 Replies
View Related
Jan 11, 2012
I am needing to upgrade the Flash card on our current ASA from 64mb to a 1GB card to make way from upgrading from 8.0 to 8.4. When i copy all the contents from the 64MB card through a card reader i am not getting the startup-config file copied over. I checked to make sure that all hidden files are shown, but i am not seeing it. I backed up the startup-config from the old 64mb card to a tftp server before switching the cards out. Is their something that i am missing?
View 4 Replies
View Related
Dec 12, 2012
I need to upgrade the ASA 5520 from OS 8.2(5)26 to 8.2(5)33. the ASA only has 64M of flash. I have a 256M flash card. What are the steps to upgrade the flash? I am not sure how it will boot up because the new flash will be blank?
View 2 Replies
View Related