Cisco Wireless :: 6500 - Why WiSM2 Not Recommended In SUP720 Slots

Jun 27, 2012

I have a situation where a customer doesn't have the required power units installed in their 6500 for me to provision a WiSM2.They use a VSS pair with a single Sup720 in each. They have no intention of adding a second Sup to each chassis.

I need to justify why they can't use slot 6 (which has power reserved) if I am to get them to upgrade the PSU's. The documentation I've found says it is supported but not recommended.

View 1 Replies


ADVERTISEMENT

Cisco :: Sup720 - Supported Slots On A 6513?

Nov 28, 2011

Can the sup720b be used in any other slot on a 6513 besides 7 and 8?

View 1 Replies View Related

Cisco Wireless :: 6500 Unable To Reach WISM2 Management Interface

Mar 28, 2012

I've just reset our WISM2 in the test lab back to factory default as I needed to reconfigure the 6500 and the WISM2 itself. Bearing in mind I had it working before.I've just renamed and re-addressed some of the vlans so things flow better and make it easier to add more WISM2s in the future.Now I've run through the initial configuration and it's rebooted ok and show WISM status is showing Oper-Up and there's a port channel 407 been created as I would expect. However, I am unable to get to the management interface via GUI or SSH. In fact from the 6500 I can't even ping the management interface (but I can the service port).The Vlans have been changed in the 6500 config so it knows the native-vlan and service vlan etc and all the vlans are up/up.

View 17 Replies View Related

Cisco Wireless :: 6500 - Unable To Connect Via GUI After Initial WISM2 Setup

Feb 7, 2013

I've installed our previous WISMs and other WISM2s previously and never had a problem.
 
6500 running SXJ2. WISM2 running 7.3.101.0 (which is what the rest of our WISM2s are on)
 
Insert WISM and go through initial setup. Run a show wism status on the 6500, and show sysinfo on the WISM. All looks good. Service port and management vlans are up. From the 6500 I can ping the service port IP, but not the management IP. From the WISM I can't ping the managment default gw but I can the service port. Unable to get anything back from the GUI..not surprising as not even ping works.
 
Now, as I said I've done it this way many times before...in fact I'm following my documentation from the last successful implementation and even adding in Cisco docs.

View 7 Replies View Related

Cisco Wireless :: Remove WiSM2 From Catalyst 6500 Series Switch?

Jul 21, 2012

how to safely remove the WiSM2 from the Catalyst 6500 series switch? According to the documentation "Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note":

To remove the WiSM2, perform these steps:

Step1     Shut down the module by one of these methods: In privileged mode from the router prompt, enter the hw-mod module mod shutdown command. NoteIf you enter this command to shut down the module, you must enter the following commands in global configuration mode to restart (power down, and then power up) the module: Router# no power enable module modRouter# power enable module mod If the module does not respond to any commands, press the SHUTDOWN button located on the front panel of the module.

Step2     Verify that the WiSM2 shuts down. Do not remove the module from the switch until the POWER LEDis off.

But, in the case of Step1 (1st methods) I do not see a option "shutdown"  in the command "hw-mod module 3"...

All I prompted to enter is: c6500#hw-module module 3 ?

boot   Specify boot options for the module through Power Management Bus control register

reset          Reset specified component

simulate  Simulate options for the module Is it hidden options?

IOS version of c6500 is 12.2(33)SXJ1
 
In the case of Step2 (2nd methods) there is not any button on the front panel of the module?
 
And yet, it is better to remove the module configuration manually or use the command module clear-config prior to removing the module?

View 14 Replies View Related

Cisco VPN :: 6500 Sup720-3B SPA IOS SXI - GRE Tunnel Will Not Come Up

Apr 26, 2011

Cisco 6500 Sup720-3B SPA IOS SXI  - GRE tunnel will not come up.It worked fine on SXF code, but the crypto map can not be applied on tunnel interface.The iskmp is up with the OM_IDLE The crypto give it a Cryto UP, the the Tunnel does not come up.  It is UP down.Does some one have a working config with a 6500 IOS SXI Train with GRE IPSEC Tunnel?

View 1 Replies View Related

Cisco Switching/Routing :: MLS Statistics On Cat 6500 With Sup720

Sep 11, 2012

when using "show mls statistics" I see a lot packets are getting L3 Processed. Does that mean they are getting software-forwarded?

IOS is 12.2(33)SXI5. 
Cat6k#show mls statistics
Statistics for Earl in Module 5
L2 Forwarding Engine

[Code]....

View 1 Replies View Related

Cisco Switching/Routing :: 6500 - Replace Sup720 In VSS

Nov 16, 2011

I have problem with the standby supervisor in 6500 vss and need to replace the supervisor.  I have follow how-to on the cisco web site url...
 
But when i boot the new standby sup720 it comes active and both supervisors is rebooting.  I wonder if i can do the replacement without rebooting both active and standy supervisor.

View 1 Replies View Related

Cisco Security :: Change Default SSH Port On Cat 6500 WS-SUP720-3B?

Jul 17, 2011

I have been net searching this question and I find answers relative to other Cisco products but not for the 6500 series. We are running entservicesk9_wan-mz.122-18.SXF17a.bin and would like to know how to change the default SSH listening port..

View 1 Replies View Related

Cisco WAN :: Cat 6500 IOS Upgrade - Installing Secondary SUP720 In 6509-E

Nov 21, 2011

I will be installing a secondary SUP720 in a 6509-E and will be upgrading the IOS on the existing SUP which is on  122-18.SXF6. I've read that this release has passed End of Critical Maintenance earlier this you. I thinking of upgrading the IOS to 12.2.33-SXJ1(ED) or 12.2.33-SXI8(ED) (possible more stable), but i'm not sure if i need any step upgrades from the current version. The SUP meets the required hardware specs and I will also be upgrading the ROMMON to 12.2(17r)SX7 first.
 
I have alot of experience upgrading IOS on routers and switches, but i just need to now if there are any gotchas that i need to know for the upgrade on the SUP.
 
The other issue is i don't believe the current IOS has been installed, are there any issue running on an IOS not installed. Patching is not available since the system is not running from an installed image. To install please use the "install file" command.

View 3 Replies View Related

Cisco Switching/Routing :: 6500 With SUP720 Recovery From ROMmon

Jan 24, 2007

if it is possible to recover a Cat 6500 that has no code on bootflash from ROMMON, and is it mandatory to have a compact flash card to do the recovery ? or can one use xmodem or TFTP ?

View 6 Replies View Related

Cisco :: Configure Netflow Catalyst 6500 With SUP720-10GE

Jun 5, 2012

I tried to configure netflow without success.
 
Setup is the following.
 
Cisco Catalyst 6509 with Sup720-10GE IOS 12.2(33)SHX7. There are around 30 L3 vlans configured on the switch. I'm only interested for the traffic on one L3 vlan which is the connection to wan cloud.
 
I wanna see only the traffic that goes to and come from the wan. On other Catalyst where I have routed interfaces i successfully configured netflow. I read a lot in the forums and documentations but i didn't find the right one.

View 1 Replies View Related

Cisco Switching/Routing :: 6500 - Upgrade From SUP720 To SUP2T With New Chassis?

Apr 28, 2013

We recently purchased 2 Cisco 6500 series switches (with Sup 2T). These switches will be replacing our old 2 6500 series switches (with Sup 720).
 
We have 70 vlans and 90+ closet switches (2900) connecting the core switches We have 2 WLC connected to the core switch. We also have a 1 x 1 connection to a VSS switch which in turn connects to our Server Co-Location data center utilizing IPSec & GRE tunnel to connect to our Server Co-Location data center.
 
Our routing protocol is EIGRP. Our VTP domain at Server Co-Location is separate from our location “A” campus. I was wondering what is the best way to migrate our Core switches at location “A” campus.
 
The requirement is we would like to replace these switches with minimum downtime.

View 6 Replies View Related

Cisco Switching/Routing :: Web-sense Security Gateways Connected To 2x 6500 SUP720

Dec 8, 2011

I have 2x v10000 Websense Security Gateways that are connected to 2x 6500 SUP720. When I turn on cluster management function between Websense appliance, they speak to each other only if they are connected in the same 6500. When they are connected one in every 6500 cluster management does not work. They are connected on the same physical vlan. Do I need multicast to be configured in the 6500 switches?

View 5 Replies View Related

Cisco Application :: Does 6500 SUP720 / 2T Support MAC Address-Table Move Update Feature

Apr 21, 2013

Does 6500 SUP720/2T support MAC Address-Table Move Update Feature?

View 1 Replies View Related

Cisco Wireless :: WISM2 7.0 To 7.2 Upgrade

Sep 17, 2012

We have some new WISM2 running 7.0.116.0, but now we need to upgrade their license to suport 1000 APs. So I am looking at upgrading the software to 7.2.110.0. We are running WCS at the moment and got NCS with the new WISM2, so going to 7.3 and buying Prime Infrastructure is not an option at the moment, thus we are going for 7.2.
 
The thing is I can't seem to find much info about this upgrade. Is 7.0->7.2 a smooth upgrade? Do we need to do any configuration changes to the WISM2 or LAP1242? We are running H-REAP, will the change to FlexConnect be affected? I can't seem to find anything regarding requirements for 6500/SUP for running WISM2 7.2, do I need a certain software for that?

View 5 Replies View Related

Cisco Wireless :: Get 250APs On Each WISM2-blade

Mar 13, 2013

I have a question regarding WISM2 DP and licensing.
 
Suppose i have a WISM2 with 7.0, 500AP license today and i activate WISM2-DP by upgrading to 7.2,Do i get 500 AP capacity for free (total 1000AP) or do i get 250APs on each WISM2-blade ?
 
If i get 500APs for free, why is Cisco selling an expensive licensed 1000 AP WISM2 ? I better buy a single-plane 500AP-WISM2 and upgrade it myself then...50% profit.
 
Is this the same for a WISM2-300 (supporting 300 APs) ?When i activate WISM2-DP here, do i get an extra 300 AP or an extra 500 APs ? Or 150AP on each blade ?

View 7 Replies View Related

Cisco Wireless :: WiSM2 7.4 And WCS Fails When Refreshed

Dec 19, 2012

I having an issue with WCS and the new code 7.4 on my WiSM2 blade.  When I try to refresh configuration from/to controller it fails.  I just upgraded from 7.01 and it worked before the upgrade.  
 
Is this not supported?  

I am able to change configuration from WCS to the WiSM2 and it works fine just cant copy config.

View 7 Replies View Related

TP-Link 300Mbps Wireless :: Expanding Port Forwarding Slots For WR-941N?

Dec 31, 2012

Region : UnitedStates
Model : TL-WR941ND
Hardware Version : Not Clear
Firmware Version : 3.12.5 Build 100929 Rel. 57776n
ISP :

I have a TP Link router model number: WR941N (under hardware version it says "v2/v3", that's why I put "not clear" under "hardware version" in the form). Whether it was possible to add even more slots for Port Forwarding for this router, the current hard limit is 16, and I would like to have more than that, what would be the procedure to do so?

View 2 Replies View Related

Cisco Wireless :: WISM2 No Port-Channel On 6504-E?

Jan 18, 2013

I have just been setting up a WISM2 in a test lab and for some reason the Supervisor is not creating a port channel on my 6500 as suggested in the WISM2 Deployment Guide. WISM2 is installed in an appropriate slot (according to same doco) and have attempted reset to factory defaults, removing and power cycling several times.

View 1 Replies View Related

Cisco Wireless :: WiSM2 Version 7.4 Cannot Work On Same Subnet

Jan 8, 2013

I have installed WiSM2 with ver 7.4 and Bonjour works great with instruction provided, But…… 2 problems. I cant get it to work on the same subnet. (odd since the whole problem was not able to work across subnets), More important the new Code function / password function on the airplay wont work. I get the code on the projector, but the ipad never pop up the login box it just errors out.

View 2 Replies View Related

Cisco Wireless :: WISM1 To WISM2 Migration With Different Image?

Dec 12, 2012

I am about to migrate WISM1 to WISM2, The image of WISM1 is 6.0.199.4 and the image of WISM2 is 7.2.111.3.
 
Do i need to upgrade WISM1 to 7.2.111.3 before i export the configuration and import it into WISM2? Or can i just export the configuration from WISM1 on 6.0.199.4 and import directly to WISM2 which is on 7.1.111.3?

View 2 Replies View Related

Cisco Wireless :: 6509 / WiSM1 Upgrade To WiSM2?

Apr 5, 2012

My company has been contracted to upgrade the 2 WiSM1 modules on a 6509 for a customer.  The hardware isn't changing but the software is being upgraded to WiSM2.  The cutsomer has HUNDREDS of AP's and dozens of VLANs and subnets (large municipality and school district).
 
Cisco SE's have been pushing the customer to purchase the WCS 7 software (they've been managing these Controllers independantly) stating there is no mechanism to upgrade WiSM1 configs to WiSM2.  I am vaguely familiar with the cisco controllers but have little WiSM experience. So i feel like i'm working without a net here.
 
So,
 
1) Any way to migrate from 1 to 2 without the WCS and without having to reinvent the wheel?
 
2)  How does the WCS make this transition easier?  What does it do to the WiSM1 configs to make them WiSM2 compatable? 

View 21 Replies View Related

Cisco Wireless :: WISM2 / Looking Individual Log Of CAPWAP Access Point?

Apr 10, 2013

I have a wireless network running with Controller WISM2 and I also have a NCS.I want to know if there is any way to look of individual log of CAPWAP and LAPWAP Access Points. It is better if I can see it through NCS.

View 1 Replies View Related

Cisco Wireless :: WISM2 Time Reset To Default After Powering Off 6505E?

Dec 16, 2012

it is normal for the WISM2 time to be resetted to default of 1 Jan 2000 after rebooting the 6506E if no NTP is configured?I had to configure it back to the correct time. If not, the APs will not come up.Also, does the ap or wlc keep track of the ap group the ap is provisioned to?

View 3 Replies View Related

Cisco Wireless :: 1142 - Maximum Recommended Clients Per Access Point?

Jan 24, 2013

We are about to upgrade our training facilities wireless and i have a few questions regarding the number of active clients we should target our design for.
 
We would be using 1142 and 3502I access points. I was thinking that  based on the belo we'd be able to support around 30-40 clients per AP.
 
Protocol
Type of web use
Amount of bandwidth allocated per device

[Code]....

View 4 Replies View Related

Cisco WAN :: 2811 - Transport Two Time Slots Over IP Network?

Aug 20, 2011

I would like to transport two time slots (TDM traffic) over an IP network in order to connect two telecom devices located in different sites, i have cisco 2811 routers on both sites with ip advanced services 12.4.20T IOS

View 5 Replies View Related

Dell :: XPS 9000 Are Expansion Slots PCI Or PCI Express

Jan 7, 2013

I want install a wireless card--dual band, N, -- in my Studio XPS 9000 desktop.  I have a dual band router.My questions:

1. Are the expansion slots PCI or PCI Express?

2. What card is recommended?

View 1 Replies View Related

Linksys Wireless Router :: E4200 USB Port / Recommended Format Of The Attached HD Drive / 512 Or 4K?

Sep 8, 2011

what is the recommended format of the attached HD drive, 512 or 4K ?

View 6 Replies View Related

Cisco Switching/Routing :: 6509 Has Four Module Slots Empty

Apr 1, 2013

I have a cisco 6509 (ws-c6509-e) IOS 12.2.(18)SXF6 with the following modules and submodules: [code] I would like to add another module, I have WS-6816-GBIC or WS-6516-GBIC which one will work with my 6509 ? The 6509 has four module slots empty: 4-7-8-9, Can I add the card in one of these slots ?

View 10 Replies View Related

Cisco Firewall :: 5510 Have 1 / 4 Memory Slots Without Having To Open Chassis

Aug 10, 2010

Is there a way of ascertaining whether my 5510's have 1 memory slot or 4 memory slots without having to open the chassis?

View 6 Replies View Related

Fitting PCI WLAN Card To A Desktop That Has Only PCIe 2.0 Slots?

Jun 4, 2011

when I browse for internal WLAN cards for my new desktop their interface is described as "PCI 32 bit", which is weird because expension slots on new desktop mobos are all PCIexpress.I know the PCIexpress's interface is physically different then PCI's, and that it carries 64 bits.So, will that work? Do you know internal cards that with PCIexpress interface?

View 3 Replies View Related

Cisco Switching/Routing :: 2960 Switch Hanging With SFP Module Slots

Sep 2, 2012

My Cisco 2960 Switch hanging problem (does not work or LED light), when i removed SFP  module slots its working fine.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved