Cisco Wireless :: Aironet 1260 Access Point Work Without Controller??

Dec 1, 2010

I would like to buy Cisco  Aironet 1260 Access Points, i just want to use them independantly so   i want to know do they work without the Wireless LAN Controller? or i  have to have the controller for them to work? they will be in different locations so i cant have a controller per each location.

View 9 Replies


ADVERTISEMENT

Cisco :: Access Point (AIR-AP1141N-E-K9) Can Work With Wireless LAN Controller (AIR-CT5508-25-k9)

Feb 24, 2011

I want to confirm if the access point (AIR-AP1141N-E-K9) can work with the Wireless LAN Controller (AIR-CT5508-25-k9)

View 2 Replies View Related

Cisco Wireless :: 3602e Access Point To Work With 5500 Controller With Code 7.0

Jun 15, 2012

i have cisco CAP 3602e series access point to work with 5500 series controller with code 7.0i did not find VCI option 60 for this type of APs to configure DHCP. How I can let these APs will join the controller, i mean through which process DNS discovery methode and what about if i need to configure option 60 and 43 in dhcp for ap joining process to controllers.

View 4 Replies View Related

Cisco Switching/Routing :: Access Point Aironet 1040 Configuration - Not Getting 802.11n To Work?

Jun 25, 2012

I can't figure out how to get the config right for the 802.11n channel to work.

View 4 Replies View Related

Cisco Wireless :: Aironet 1260 As Bridges?

Feb 2, 2012

Is it possible to create a wireless site to site link using 1260 access points as bridges (like the 1300 series)?
 
Also if so, can you use 11n channel bonding on the bridge link?
 
I need to link 2 buildings together wirelessly approximately 70 metres apart.  There is direct line of sight between them.

View 10 Replies View Related

Cisco Wireless :: How To Setup A Standalone Aironet AP 1260 Series

Sep 13, 2011

I'm new to the Cisco Aironet Access Point. I got a new STANDALONE Aironet 1260 series access point device. The part # AIR-AP1262N-A-K9. The shipping package did not come with any guide, CD, and power adapter. I searched the Cisco sites, but could not find appropriate manuals. I did find a getting started guide but not for standalone AP, it's for Controller-based AP. Question - where can I find manuals / guides to set up and configure my new standalone Cisco Aironet Access Point 1260?

View 3 Replies View Related

Cisco Wireless :: Aironet 1260 Series - Sending Station Has Left BSS

Oct 29, 2012

We have been having issues with random packet drops and or some sort of radio lockup which happens a few times a day. I have a test AP setup with a few clients only a few feet away and I see this combination of messages. Should I be seeing these clients drop off and then reconnect immediately? Granted these test clients are not passing much data but my assumption is that they would not become deauthenticated because of lack of activity? This setup is using a radius server for authentication. I tested it before with just WPA2 PSK and only had a few disconnected over a number of days, compared with many a day with the Radius.

View 1 Replies View Related

Cisco Wireless :: Aironet 1260 Series MAC Filtering In Autonomous Mode

May 13, 2013

Do we have Option to add MAC address of specific laptop or Mobile to connect to the Access Point in cisco Aironet AP 1260 series in Autonmous mode

View 4 Replies View Related

Cisco Wireless :: Controller 4400 Series Work With Aironet 3600 Series

Mar 6, 2012

Can Controller 4400 series work with Aironet 3600 series?

View 5 Replies View Related

Cisco Wireless :: Is Aironet 1260 Good For Indoor LWAP Or CAPWAP Environment

Jul 12, 2012

Is Aironet 1260 good for indoor LWAP or CAPWAP environment? Do we need external antenna for the Aironet 1260 access point when using it indoor?

View 1 Replies View Related

Linksys Access Point :: To Work The Wireless Repeater Mode Work With WPA2-AES

Sep 6, 2011

Is there any chance the Wireless Repeater mode work with WPA2-AES ?If not, which model of AP should I buy to connect it with my wap54g as Wireless Repeater?

View 4 Replies View Related

Cisco Wireless :: 2504 Controller With 3 Aironet 1142 Access Points

Mar 16, 2013

I have installed/setup a cisco 2504 wireless controller and 3 aironet 1142 access points using the basic config on a windows sbs 2008 domain, the problem is that the clients that are connected to the 2504 aint getting the there ip addr from the AD but from the wireless controller, and there cant reach the clients on wifi from the clients that are connected to lan, is there anyway that i cant change this so that a client on lan can see the client on wlan and vice versa.

View 5 Replies View Related

Aironet AIR-AP1252G-A-K9 - Wireless Access Point

Mar 19, 2011

I just picked up a Cisco Aironet AIR-AP1252G-A-K9 Wireless Access Point to mess around with at home and learn IOS.

The unit didn't come with a power adapter or any accessories. Just the bare AP. Does this AP need a controller to work? Can I use it as a standalone AP?

View 2 Replies View Related

Cisco :: Aironet 1260 WDS Setup?

Jan 23, 2013

I was wondering if its possible to setup the Cisco Aironet 1260 as a WDS master with radius and another Cisco Aironet 1260 as a slave for seamless roaming. How many slaves can a WDS master handle?

View 1 Replies View Related

Cisco Wireless :: Aironet 1130AG - Login To Wi-Fi Access Point?

Oct 13, 2010

I am trying to find a way to login to our wirless access point. I have a Aironet 1130AG series wireless router. I have the ip address. It is a POE device so i dont have a power supply for this device. When it is on I can see the Wireless Network but the passcode has been lost and no one knows it. Is there a default IP address for this equipment? There is an Ethernet port for a console but without the power supply i cannot access it.

View 3 Replies View Related

Cisco Wireless :: Aironet 1040 Access Point Managing

May 22, 2012

We are currently using several AP's in our organization. And in this one AP i want to give a user the power to change the password of the wireless network to prevent miss use. I was wondering if it was possible to create an account who only has the privilege to change the WPA key?? I want to prevent that he will accidently change other settings.

View 5 Replies View Related

Cisco Wireless :: Aironet 1310 - Outdoor Access Point

Sep 13, 2012

I am looking at outdoor access points, I want to stick with Cisco aironet, we currently have 6 of them that are 6 years old and running great, one has had a problem because of humidity, dried it out and relocated and we are good again.
 
I was looking at the Aironet 1310 Outdoor access point, but I can't find much information on it.  I am looking to see how many SSIDs can be setup, we currently have 2 one private, and one public, this is done with VLANS.  I am also looking at finding out about the power injector, it converts to coaxial cable, it has 2 RJ-45 and 2 Coaxial, does this mean if we get 2 access points, then I only need 1 power injector?

View 1 Replies View Related

Cisco Wireless :: Setting Up Aironet 1040 Access Point

Mar 13, 2013

I'm working on setting up an Aironet 1040 Wireless Access Point for my company.  It's my first time setting up something like this, and I've run into a bit of trouble.
 
I created my first SSID easily enough, following the manual and guides online.  I set up VLAN 1 as my native VLAN and linked it to my SSID with the encryption and security that I was told to use and it works great.  However, my boss asked me to set up a second connection as well for guests at the office, and this is where my trouble starts.
 
I created VLAN 2, and then another SSID which I linked here.  I set up encryption and security the same way, and I can see the network when I open up my network and sharing manager.  I can connect to the network as well, but I either get a spinning blue icon where my signal strength indicator is or a few bars with a yellow caution sign, and Windows says 'Identifying...'.  I've compared the two SSIDs using the console and the GUI and I can't seem to spot any obvious differences between them.

View 4 Replies View Related

Cisco AAA/Identity/Nac :: AIRONET 1260 With New Radius ACS 4.x?

Nov 18, 2012

I have CISCO ACS 5.1 radius for VPN on ASA and tried to configure an NDG on it for AIRONET 1260 too and worked fine with IEEE 802.1x CISCO EAP-FAST authentication As I had some trouble to let users to authenticate only on VPN if are VPN users and only on CISCO AIRONET if need only WIFI AIRONET I tried exception policies rules but something not working. VPN was ok but not WIFI access denied for rule policy access I decided to install CISCO ACS 4.x on Windows 2003 that is on ACS 5 DVD I created NDG as done on ACS 5 put a shared secret , put on AIRONET too as done for ACS 5 but I receive an error against ACS 4.x To troubleshout it I tried [URL] but not work ! I think to have done all fine owever on ACS 5 it worked in 5 minutes I searched log inside ACS 4 and found "Invalid message authenticator in EAP request" and I found this: [URL]Changed shared secret more times but ever not workign with ACS 4 I need to have user and password prompt on client trying to authentincate on AIRONET WIFI and I need ACS INTERNAL USER no active directory, no LDAP , no external user database?

View 1 Replies View Related

Cisco :: Aironet 1260 Authentication Server

Sep 13, 2012

I have 3 Aironet 1260's with the same SSID and set with Open Authentication with MAC Authentication. Can I designate one of the 1260's as the MAC Authentication Server? I have all 3 now working with MAC Address Authenticated ty Local List Only and have to put the new MAC address in all 3.

View 3 Replies View Related

Cisco Wireless :: Aironet 1262N - Access Point Behind Non-Root Bridge?

Apr 9, 2012

I want to connect two buildings. Let's call them Building A (main) and Building B.
 
 „A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
  
„B“ is a pretty large building and has a wired LAN from one end to the other end.
So I placed two 1262N there, each at one end.
 
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
 
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
  
My Questions:
 
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?

2. How Do I tell AP03 that it should use AP02 as a gateway to building A?

View 2 Replies View Related

Cisco Wireless :: 1242AG / Maximum Associations In Aironet Access Point?

Feb 12, 2011

I have a very special application where I need to connect as much as possible end devices to a single access point.The required data throughput per end device is very small - around 1 to 5 kbit/sec.I am using the Access Point Aironet 1242AG.

Questions :

1.    What is the maximum number of simultaneous users that can be connected to a Cisco Access point, is it 255 or can be more ?

2.       If I define multiple SSID’s, what if the total numbers of users that can be connected to a Cisco Access point

3.       I there a simulator tool that can be used to simulate multiple wireless connections to an AP

4.       Have anyone tested so many users connected to 1 Access point ?

View 7 Replies View Related

Cisco Wireless :: Aironet 2602e Configuration As Standalone Access Point

Mar 19, 2013

I must configure an Aironet 2602e Access Point, as a standalone access point (without WLC), but I can not find Configuration Guides for that. I have only found the "getting started guide" but there is described an installation combined with a WLC, which I have not. Is it provided no real guidance from Cisco? I did something never done before.

View 2 Replies View Related

Cisco :: Make SSID Hidden Aironet 1260?

Mar 28, 2013

We have three Access Points, two Cisco Aironet 1260 and one 1240AG. Originally, the SSID was hidden on all three AP's and users had to go to Other Networks and type in the SSID and password to access the WAN. About a few months ago, the network started broadcasting to the public. I am trying to make the SSID hidden again. I have tried going to the Security tab, choosing the  SSID Manager and setting single guest mode to none but it has not worked.

View 4 Replies View Related

Cisco Wireless :: How New 1260 Will Work In Mixed Environment

Aug 2, 2011

I am looking to slowly migrate some of our wireless devices (Aironet 1231 and 1232's) to the Wireless N spec - 1260's.I currently have four AP locations that I want to upgrade first before anywhere else. At the minute, these four AP's work on the 2.4Ghz G band.
 
how the new 1260's will work in the mixed environment. I believe I will need to purchase the 1262 (which is the dual band version) so that I can operate the AP in both the 2.4Ghz G band range and the 5Ghz N range at the same time, is this correct?If I was to purchase the 1261 (which is the single band version), will I only be able to operate in either th 2.4Ghz or 5Ghz, but not at the same time?
 
For the mixed environment, would you suggest the dual band version? Can I place the same SSID on multiple Radios if this is the case? Following example: Say I have the SSID called 'Company' - this at the minute is operating on the G band 2.4Ghz range. If I was to purcahse the dual band 1262, could I put this SSID on both the G radio and the N radio? Would clients with an N adapter automatically connect to the 5Ghz range (N Radio) and legacy G and B adapters automatically connect to the 2.4Ghz (G Radio)?

View 5 Replies View Related

Cisco Wireless :: Change IP Address Of Aironet 1200 Series Access Point

Dec 30, 2012

we have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.

View 17 Replies View Related

Cisco Wireless :: Aironet 1140s - How To Connect Repeater To Specific Access Point

Feb 12, 2013

In our office, we have 3 Cisco Aironet 1140s and they are configured as follows: 

* Access Point A (192.168.0.50)
* Access Point B (192.168.0.51)
* Repeater (192.168.0.49)
* SSID : 101
 
how to have the Repeater connect to Access Point A only?

View 3 Replies View Related

Cisco Wireless :: Perform Site Survey With Aironet 1041N Access Point?

Jul 15, 2012

We are in need to perform a site survey with the Aironet 1041N Access Point.
 
Upon reviewing the site survey software, it seems you need to use an Aironet adapter. However from what i can tell, all the Aironet adapters are PCMICA cards, which most modern laptops do not have, and the PCMICA cards that do exist don't have drivers for windows 7.
 
Are there USB adapters w/ Windows 7 drivers that can be used to perform a site survey?

View 2 Replies View Related

Cisco Wireless :: Aironet 1310 - Infrastructure Access Point Unreachable For Management

Sep 16, 2010

We have 2 aironet 1310 aps setup as infrastructure access points between 2 buildings.  One went south on us & we placed it.  Before the bad one went down, we were able to manage both remotely & could see them from the next device via CDP.  Now, we can't connect or even ping either AP.  And the weird part is that the switches that connected to each can see each other via CDP, but not the access points between them.  I'm attaching the configuration.  Before I make the 2.5 hour drive back to the site, what I may have misconfigured on either or both access points?

View 3 Replies View Related

Cisco Wireless :: Replacing AP1231G-E-K9 (LEAP) With New 1260 / Will It Work

Aug 24, 2011

iam currently trying to replace AP1231G-E-K9 with new equipment / Cisco AP next generation  maybe?The problem is that the system, that is going to use the AP is using aironet 350 PCMCIA adapter with LEAP. If in fact we are going to use a new Cisco AP, will the new generation work with Aironet 350 Adapter and support LEAP?

View 2 Replies View Related

Cisco Wireless :: Aironet AP-1041N Setting To Have Access Point Broadcast Multiple SSIDs

Jan 17, 2013

I have recently purchase Aironet Access Point. I'm pretty new to Cisco systems and what i'm try to do is have the access point broadcast multiple SSIDs lets call them Guest and Admin. My problems is when i config router to have a DHCP address it works perfectly fine but when i assign a static IP it shows all the any connected device as unkown with IP 0.0.0.0. So i'm guessing i will need to setup a dhcp server. Is there a way access point can have its own DHCP server and IP address ( i don't want to use any from my STATIC ip subnet as i dont know alot of empty ones left) like home wifi router where they assign each device an IP like 192.168.0.1. Is this possible?

View 1 Replies View Related

Cisco Wireless :: 4400 How To Get New Access Point To Be Seen By Controller

Jul 23, 2012

I have a Cisco Series 4400 WLAN controller and I'm trying to connect a lightweight AP to the controller.  I have already assigned the switch port to use my wi-fi VLAN, and have connected the AP to the switch.  After a few minutes, the light on the AP goes from green to light blue (indicating it's serving clients). When I log into he wi-fi controller to look for the Ethernet mac address of the new AP, I do not see its Mac Address.  I want to be able to rename the AP to reflect where it will be used,  but need to select the AP via its Ethernet mac address before I can make any edits like changing its name etc. I've gone through the "monitoring" menu, selected "All" and still do not see it in their via its MAC address.  I also will select the "wireless menu" which lists all the AP's on my network, listing in order from on the longest running, to just powered on.Is there something I'm missing like a "re-scan" that scan's all devices?

View 5 Replies View Related

Cisco Wireless :: 1262AP / Access Point Not Online On Controller?

Dec 3, 2012

I have been trying to get a 1262AP registered to wireless lan controller. The core switch has three 2 vlans in it, management which is vlan 41 and AP interaction vlan which is vlan 51.Controller also has both these vlans.
 
Vlan 41 - 192.168.40.x/23 ( management vlan)
Vlan 61 - 192.168.61.x/24 (AP vlan)
 WLC management interface IP is 192.168.40.18
WLC AP interface IP is 192.168.6.241
 
Now , during the initial steps, the access points are attached to the switchports on vlan41, wherein they get the dhcp ip from the temporary pool created on the controller and get registered.But, these access points in actual environment needs to be on static ip address. When it's ip is changed to a static IP address from the controller , it fails to register to the controller. the switchport is put on vlan6 as access port , after  static ip is assigned to the access point.The error i receive is ;
 
%CAPWAP-3-EVENTLOG: Could not resolve gateway. Not sending discovery request to 0.0.0.0, type 1

the core switch we are using in this new setup is a 2960 with a lanbase image. I realised the switch is not routing enabled. it doesn't accept the command "ip routing". Will this be creating a problem for the access points?  From the switch , the controller management and AP vlan IP address can be pinged. similarly, from the controller, AP and management vlan interface ip address of the switch can be pinged.

View 18 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved