Cisco Wireless :: Mesh 1260 Ethernet Bridging With VLAN Tagging

Mar 18, 2012

I'm a little stuck with a 4400 7.0.220.0 + RAP 1550 + MAP 1260 Ethernet bridging issue. I'm using the VLAN tagging functionality and I'm finding that periodically a VLAN that I've tagged on the MAP will deregister from the backhaul and stop passing traffic. If I go into the Mesh tab on the MAP, select the wired interface, remove the VLAN from the list of tagged VLAN IDs and then add it right back to the list, its starts passing traffic again

View 2 Replies


ADVERTISEMENT

Linksys Wireless Router :: Vlan Tagging On E4200 / WRT610n?

Feb 14, 2012

I rencently bought the E4200v1 router, to be wired together with my WRT610nv2 to form gigabit network for different floor network.However with the recent installation of fiber to home network offered by my local ISP, I would need router that capable for performing vlan tagging (500 for internet & 600 for IPTV).Would like to know if Cisco have any development plan to enable the VLAN option for:-

1. E4200
2. WRT610nv2
 
At the moment, I'm still stuck with the provider "home-made" router which lacks of Gigabit & dual band wireless.

View 9 Replies View Related

Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?

Apr 16, 2013

I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?

View 6 Replies View Related

VLAN Tagging On A HP Procurve?

Jul 29, 2012

Unfortunately I do not remember the model and the switch is a couple of hours away without remote access.I have 4 vlans on a procurve switch.

VLAN1 - Network Devices (Server, printers, WAPs)
VLAN100 - Admin (Office workers)
VLAN200 - Teachers
VLAN300 - Students

There is a server doing DHCP. There are 4 ranges of IPs 1 for each VLAN.

The router is on Port 44. VLAN 1, 100, 200, 300 - Tagged

The Server is on Port 46. VLAN 1 - Untagged

The WAPs are on Ports 1, 11, 31 VLAN 1, 100, 200, 300 - Tagged

All other ports are on VLANs 100, 200 or 300 - Untagged

The WAPs all have VLANs 100, 200, 300. Each VLAN on a different SSID.

I have IP helper with the server IP on VLANs 100, 200, 300.

There are IPs from the different subnets on their respective VLANs in the switch.

The gateway for each subnet is on a different subinterface on the router.

The router is a linux box. (Untangle)

The WAPs are not able to talk to the server, therefore no computers on the wireless networks can get an IP.The server can only talk to the router if I change port 44 to untagged.What combination of tagged and untagged ports do I need to make everything talk?

Do I need to put the VLANs on the subinterfaces of the router?

View 1 Replies View Related

Cisco Switches :: VLAN Tagging Across From Firewall To Two SG-300

May 18, 2011

I need some assistance in setting up VLAN's (802.1Q) accross two switchs, I want the same 2 vlan's on both switchs, how do i configure them to be connected and pass both vlan's traffic.VLANs from firewall are tagged at 3 and 8.Single port out from the firewall.The first switch is simple enough, port is connect at port 52 and configured from both vlan's then the individual ports are either on one or the other.  The question is how do i connect the second switch so that it can also do both vlans.  Assume I connect switch1 at port 51 to switch 2 port 52.  Do I configure both ports to be on the same VLAN's. or do i setup LAG's.

View 3 Replies View Related

Cisco Switches :: VLAN Tagging ESW-540 And 3750g

Aug 19, 2011

I am currently tasked with setting up a network, pretty much from scratch, that requires some fairly hefty VLAN deployment. My hardware on hand (already existed so can't can't change anything easily) 5x ESW-540-48 Switches, 1x3750g switch, 1x2811 router.  I don't believe the router should be required as the 3750 is capable of intervlan routing. [code]
 
Now at one point I actually had the VLAN's *working* in that I could specify an IP address and could ping to and from it!  However DHCP wasn't passing despite numerous attempts with DHCP relay and IP-Helper configurations.Also I was having issues with VLAN 1 as the native VLAN, the ESW switches don't allow you to do much with them, as they 'weren't created by the user'.  So tried switching that out to VLAN11 also but with very little success there (I had to change the native vlan on all trunks to VLAN 11)All the 10.x.x.x addresses need to be able to communicate with each other.All the ESW switches need to be able to handle their respective VLAN's as well as VLAN 1 (for Printers and wireless access points distributed around the building).

View 16 Replies View Related

Vlan Tagging In Nortel BES110 Switches?

Nov 23, 2011

We are having one HP core switch and VLAN is configured on it. Four Nortel BES1010(24port) switches will be connected to this HP switch. We need to configure the VLAN tagging in the Nortel switches in order to make deices connected to nortel switches can communicate with devices in the VLAN.

View 3 Replies View Related

Cisco :: VLAN Tagging At Access Port In Switch?

Sep 28, 2012

I'm Confused from the fact that Vlan tagging is done at access port and trunk port always gets tagged packets (untill its case of native vlan).But I still believe in other fact which says tagging happen only when a frame hit the trunk port which means trunk port gets untagged frame and tagging is not possible at access port.

Would like to know where actually this tagging happens ?

and also which command we can use to encapsulate 802.1q protocol to access port ? The way we do at trunk port is #switchport trunk encapsulation dot1q Is the above command applicable for access mode also?

View 6 Replies View Related

Cisco Routers :: SF300 24p Vlan Tagging Being Stripped?

Feb 13, 2012

I have a sf300 with (2) vlans (1) ] vlan for data and vlan (100) is my voice vlan I have Vlan (100) tagged traffic, and my VoIP pbx as an access port only to vlan (100) all other ports are trunk ports with vlan (100) tagged and vlan (1) untagged traffic. I get no outbound audio on calls I can call out hear them fine they cant hear me. I am wondering if my tagged traffic leaving the phone is being striped and if so were. I have CDP turned off.

View 1 Replies View Related

Cisco Switching/Routing :: Determine VLAN Tagging On A 3550?

Jun 13, 2013

We are trying to replace the CSS between our firewall and DMZ with a BigIP.  Among it's other functions, it will act as the router between the firewall and the DMZ. To make this work, I need to assign vlan tags values for the vlans I create on the BigIP box and these must match the tags on the cisco switches (3550's)  How do I find this information on the switch?

View 2 Replies View Related

Cisco Firewall :: VLAN Tagging To ISP Through ASA 5510 To Remote Site

Oct 25, 2012

we have a base license ASA 5510, and been trying to get ICMP working to check that we're routing and not hitting any NAT translation. We have a VLAN280 setup to ISP for VPN link to remote site and another VLAN281 for internet access for internal users.
 
Users can browse internet from (name _inside interface e0/1 access port) which is fine. When I do a ping to remote office through the VPN I get a response pinging from VLAN280 name VPN_Link. When I do a ping from name inside interface I don't get a response both are security level 100 with same-security-traffic permit inter-interface configured.
 
Config:
 
!
interface Ethernet0/0
speed 100
no nameif

[Code]....

View 11 Replies View Related

ASA 5505 - VLAN Tagging / Trunking Power-connect 2716?

Oct 30, 2011

Having an issue getting my DMZ vlan working. Running my ASA5505 and i have configured e0/2 for DMZ w/ VLAN ID 3. Connected to my 2716 on port2.Inside e0/1 w/ VLAN ID 1. Connected to my 2716 on port1.

I am trying to get my DMZ Vlan to ports3&4 (LAG1) but when i assign the LAG group to PVID 3 i lose connectivity on VLAN1. I want to send both VLANs to that host because the teamed adaptor is used for Hyper-v Network Switch.

View 17 Replies View Related

Cisco Switching/Routing :: 2960 / Verifying Trunk Vlan Tagging?

Jul 5, 2012

I have a 2960 switch connected to another. The I need to verify that vlan0010 on one switch is forwarding tagged traffic between the other switch it is hooked up to through the Gi0/1 port. How do I verify this? I have a server that's multihomed (Broadcom) on the other side an it is supposed to be on this vlan with one of it's network interfaces. We had a pwer outage and now it cannot communicate on this vlan. However, everything else on the vlan can reach all the other nodes accept this server in the front of my building. All the devices in the same room are linked to the same switch which has one port (fa0/17) on vlan0010 and can ping eachother just fine. The server is hooked to port 24 on my server room switch and Gigabit port one goes to a fiber converter all the way to the back. It then gets converted from fiber to cat5e again and links into the switch (2960) in the backroom.

View 5 Replies View Related

Cisco Switching/Routing :: Disable Administrative Native Vlan Tagging On 6509?

Dec 13, 2012

We have a problem with CDP packets on sent by our Cisco 6509's.  Unlike our other Cisco switches (4948G, 5020, etc.), the 6509 tags administrative traffic on the native vlan.  As a result the CDP packets are sent with an 802.1Q header with a tag of 1.  The other switches send the CDP packets untagged on the native vlan.  This causes problems because we have non-Cisco devices in our lab that also receive and send CDP, but they do not process the packets that are tagged by the 6509.  They see the packets from the 4948 and 5020 just fine.
 
How can I disable the administrative native vlan tagging on the 6509?  Here is the current setup:
 
nwkdev-6509-1#show vlan dot1q tag native
dot1q native vlan tagging is disabled globally
nwkdev-6509-1#show interfaces gigabitEthernet 1/9/1 switchport

[Code].....

View 13 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 / Maxis FTTH Either Via VLAN Tagging Option / Maxis Mode?

Feb 26, 2013

Region : Malaysia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : Maxis

I bought the TL-WDR4300 almost 6 months ago using it on my TM Streamyx broadband service, it worked perfectly and this is indeed a very good product very reasonably priced too Kudos to TP-Link. The thing is shortly after purchasing it, I moved to Maxis Home Fibre Internet (more bandwidth). Following the ISP change the router has since went back into the box and had been there for 5 months now. This is because without the VLAN tagging feature or a Maxis mode, it is currently incompatible with Maxis Home Fibre Internet and will stay that way.I understand this is by no mean TP-Link's fault but I and many other WDR4300 owners on Maxis, if TP-Link could look into ENABLING VLAN TAGGING FEATURE/MAXIS MODE on this device. This I am sure would work with TP-Link sales as there are not many routers out there with this feature set and price range that could work with Maxis Home Fibre Internet.

View 1 Replies View Related

Cisco Wireless :: WLC 2106 / Setup Mesh And Use Ethernet Bridge Port On MAP To Extend Network?

Mar 3, 2013

I've a WLC 2106 and it is running IOS version 7.0.240. I am trying to setup a wireless mesh and used the Ethernet bridge port on the MAP to extend the network. The wireless mesh works fine but I can not get the switch to work that is connected to the ethernet port on the MAP.I'm using two different Access points. I'm using a Air Cap 3502i as the RAP and a Air Lap1142N as the MAP.The switch port that is connected to the RAP and MAP is configured as the following:

switchport mode trunk
switchport trunk native vlan 2
switchport trunk allowed vlan 10,20,30,40

[code]....
 
The wireless mesh between the RAP and MAP works fine. I can connect a device to the MAP wirelessly and access the network with no problem but I can not get anything to work that connects to the switch that is connected to the MAP ethernet port.

View 2 Replies View Related

Cisco Switching/Routing :: WS-C3560G-24PS / Native Vlan Tagging And Vty Access To Autonomous APs?

Jan 14, 2013

I've been experimenting with the 'vlan dot1q tag native' command on a switch and it seems as though tagging the native vlan breaks vty access to my access point.With the 'vlan dot1q tag native' commnand applied, I lose management connectivity to the AP with 'no vlan dot1q tag native' applied, connectivity is restored. Why is this? Is it safe to say that one can access the AP via vty lines using ONLY untagged packets? 
 
SWITCH
Model: WS-C3560G-24PS
Code: c3560-advipservicesk9-mz.122-46.SE
--Abbreviated CONF
 vlan dot1q tag native

[code]....

View 14 Replies View Related

Remote VPN Ethernet Bridging?

Apr 10, 2013

I have a computer with special software, customer abroad has a Laptop and connect multimedia center via etherner port to this laptop, I want to connect directly to customers ethernet port so I can program that multimedia center using a software in my PC. I know the ip address of multimedia center, but I cannot ping to it then I use hamachi port bridging.

View 1 Replies View Related

Cisco Switching/Routing :: Bridging F4 And VLAN On C881SRST

Feb 20, 2013

I am trying to have F4 (the WAN interface) bridged to a VLAN interface. I have put my VLAN interface and my F4 in the same bridge-group, set an IP in the BVI Interface, and made sure that VLAN was properly trunked and configured on one of the router's switch ports
 
In other words, I need F4 to be treated as a switchport in access mode on my VLAN 10.
 
(...)
bridge irb 
(...)
 interface FastEthernet0
description trunk
switchport trunk native vlan 10

[Code].....
 
A ping in my vl10 VRF to 10.0.0.1 does not work. ARP does not resolve.

View 1 Replies View Related

Cisco Switching/Routing :: Vlan Bridging On ASR1001?

Mar 25, 2013

I have following requirements to implement on cisco asr1001 router.
 
1.G0/0/0 and G0/0/1 interfaces are connected to a swith through trunk. Multiple customers  are will be using this trunk interface . Each customer will have subinterface with dot1q tag.
 
2 I want both sides of the ASR1001 to be in same segment .
 
3 If above two is possible I would like to implement shaping on each customers sub-interface level
 
is above implementation is possible on asr1001. configration and ios information. I found a technology called EVC . but I am not sure is that the one suited for me.
 
 network diagram is attached seperately.

View 3 Replies View Related

Direct Connection To Remote VPN Ethernet Bridging?

Apr 10, 2013

I have a computer with special software, customer abroad has a Laptop and connect multimedia center via etherner port to this laptop, I want to connect directly to customers ethernet port so I can program that multimedia center using a software in my PC. I know the ip address of multimedia center, but I cannot ping to it then I use hamachi port bridging.

View 1 Replies View Related

Cisco :: WET200 Ethernet Bridging Unit - Wi-Fi Signal Very Poor

Jul 6, 2011

I am completely new to wireless networking and know next to nothing. I own an apartment on a complex abroad and they have recently had wireless internet installed. There are some areas of the complex where the signal is very poor.

I have some Cisco small business WET200 ethernet bridging units and was wondering if these would be suitable to boost the signal in these Black spots. How to set this up or any suitable products to over come this problem.

View 1 Replies View Related

Cisco Switching/Routing :: Bridging Routed Ethernet Ports To L2 Switchports On 2801?

Jan 1, 2013

I have a Cisco 2801 with a 4 port Layer2 switch card installed (HWIC-4ESW).
 
How do I bridge Ethernet0/1 to the 4ESW so if you were to plug a computer into the 4ESW, it would be on the same network as Eth0/1?  see my config below:
 
interface FastEthernet0/1
description Internal Interface
ip address 10.1.2.1 255.255.0.0

[Code].....

View 2 Replies View Related

Cisco Wireless :: 871w Ethernet And Wireless On Single Vlan

Jan 16, 2013

I'm trying to setup a cisco 871w router in a very simple configuration using only 1 vlan. I have the FastEthernet interfaces setup such that when you plug in a client computer into one, everything works as expected. I'm now trying to set up the wireless portion. From what I've read on the internet, I managed to bring up the Dot11Radio0 interface and the BVI interface. It's a little confusing to me, but it looks like I need the BVI to bridge the wireless interface to the vlan? I'm not sure how it works...

Anyway the problem is that I can connect to my wireless network, but after authenticating, there is no ip address being assigned to the client. I don't think I'm bridging the interface correctly or something. Windows 7 gives me a yellow exclamation icon on the wireless tray icon saying "no internet access".
 
Here's my config:
 
enable
config t  
hostname [name]
 interface FastEthernet 4

[code]....

View 4 Replies View Related

Cisco Wireless :: Current IOS For 1260 AP?

Jun 12, 2012

What is the most current version oF IOS for the following Wireless AP(Aironet 1260)
 
Product/Model Number:      AIR-AP1261N-E-K9
System Software Filename:     ap3g1-k9w7-tar.124

View 2 Replies View Related

Cisco Wireless :: Aironet 1260 As Bridges?

Feb 2, 2012

Is it possible to create a wireless site to site link using 1260 access points as bridges (like the 1300 series)?
 
Also if so, can you use 11n channel bonding on the bridge link?
 
I need to link 2 buildings together wirelessly approximately 70 metres apart.  There is direct line of sight between them.

View 10 Replies View Related

Cisco Wireless :: Antenna Separation For AP 1260?

Oct 24, 2012

We are installing 1260 Access Point (AIR-LAP1262N-E-K9) with 2 sets of external antenna:AIR-ANT2460NP-R (2.4Ghz, Patch Wall-mount, 6dBi Directional) & AIR-ANT5160NP-R (5Ghz, Patch Wall-mount, 6dBi Directional).What would be the recommended separation of the 2 antennas if they will be mounted beside each other?

View 1 Replies View Related

Cisco Wireless :: Upgrade IOS Image For 1260 AP?

Nov 3, 2012

i have cisco 1260 Access point with standalone ios  ap3g1-k9w7-tar.124-23c. i download new IOS to connect the AP to the controller the new ios is  ap3g1-k9w8-tar.124-23c.JA5.tar. upgrade th AP to LAP. is it just install ios like in router & switch by tftp?

View 1 Replies View Related

Cisco Wireless :: 1260 Can't Get IP Address And Can't Joint WLC

Nov 24, 2012

i have Cisco WLC 2504 & 1260 LAP.i connect the WLC to L3 switch & connect the LAP to another port in the same L3 switch.i configure DHCP on the same switch to provide ip for the LAP , but the LAP can't get an ip address and can't joint the controller.also if when i login to the LAP i can't enter the configuration mode.

View 6 Replies View Related

Cisco Wireless :: 1260 And 3500 - Bridge With Two AP's

May 14, 2013

So I'm going to bridge two Cisco AP's 1260 and 3500, which have an 880 router on each side.
 
(Currently I have a VPN set-up through the internet for the two locations to communicate) (Naturally they are currently in different subnets) Will absolutely change this and set up as one subnet. There is VLANs setup on each router (same VLANs)
  
VLAN 1
  
And
  
VLAN 10 
 
Everything is configured on the Routers and AP's for these VLANs (works flawlessly over the VPN). 
 
So now since I’m going to get rid of the VPN and set-up a bridge with two AP's, will having same VLANs across both routers be a problem? Will VLANs work OK through the bridge?
  
Besides using (IP helper address DHCP-IP) command on the non-root bridge side router to forward DHCP requests to the root bridge side router, Also I want to be able to route internet traffic on the non-root bridge side through the WAN port, and only route LAN traffic through the bridge..

View 1 Replies View Related

Cisco Wireless :: Configuring A 1260 Autonomous AP Documentation?

Mar 5, 2012

good docs for configuring a 1260 autonomous AP?

View 1 Replies View Related

Cisco Wireless :: How New 1260 Will Work In Mixed Environment

Aug 2, 2011

I am looking to slowly migrate some of our wireless devices (Aironet 1231 and 1232's) to the Wireless N spec - 1260's.I currently have four AP locations that I want to upgrade first before anywhere else. At the minute, these four AP's work on the 2.4Ghz G band.
 
how the new 1260's will work in the mixed environment. I believe I will need to purchase the 1262 (which is the dual band version) so that I can operate the AP in both the 2.4Ghz G band range and the 5Ghz N range at the same time, is this correct?If I was to purchase the 1261 (which is the single band version), will I only be able to operate in either th 2.4Ghz or 5Ghz, but not at the same time?
 
For the mixed environment, would you suggest the dual band version? Can I place the same SSID on multiple Radios if this is the case? Following example: Say I have the SSID called 'Company' - this at the minute is operating on the G band 2.4Ghz range. If I was to purcahse the dual band 1262, could I put this SSID on both the G radio and the N radio? Would clients with an N adapter automatically connect to the 5Ghz range (N Radio) and legacy G and B adapters automatically connect to the 2.4Ghz (G Radio)?

View 5 Replies View Related

Cisco Wireless :: Replacing AP1231G-E-K9 (LEAP) With New 1260 / Will It Work

Aug 24, 2011

iam currently trying to replace AP1231G-E-K9 with new equipment / Cisco AP next generation  maybe?The problem is that the system, that is going to use the AP is using aironet 350 PCMCIA adapter with LEAP. If in fact we are going to use a new Cisco AP, will the new generation work with Aironet 350 Adapter and support LEAP?

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved