Cisco Wireless :: Replacing AP1231G-E-K9 (LEAP) With New 1260 / Will It Work

Aug 24, 2011

iam currently trying to replace AP1231G-E-K9 with new equipment / Cisco AP next generation  maybe?The problem is that the system, that is going to use the AP is using aironet 350 PCMCIA adapter with LEAP. If in fact we are going to use a new Cisco AP, will the new generation work with Aironet 350 Adapter and support LEAP?

View 2 Replies


ADVERTISEMENT

Cisco Wireless :: How New 1260 Will Work In Mixed Environment

Aug 2, 2011

I am looking to slowly migrate some of our wireless devices (Aironet 1231 and 1232's) to the Wireless N spec - 1260's.I currently have four AP locations that I want to upgrade first before anywhere else. At the minute, these four AP's work on the 2.4Ghz G band.
 
how the new 1260's will work in the mixed environment. I believe I will need to purchase the 1262 (which is the dual band version) so that I can operate the AP in both the 2.4Ghz G band range and the 5Ghz N range at the same time, is this correct?If I was to purchase the 1261 (which is the single band version), will I only be able to operate in either th 2.4Ghz or 5Ghz, but not at the same time?
 
For the mixed environment, would you suggest the dual band version? Can I place the same SSID on multiple Radios if this is the case? Following example: Say I have the SSID called 'Company' - this at the minute is operating on the G band 2.4Ghz range. If I was to purcahse the dual band 1262, could I put this SSID on both the G radio and the N radio? Would clients with an N adapter automatically connect to the 5Ghz range (N Radio) and legacy G and B adapters automatically connect to the 2.4Ghz (G Radio)?

View 5 Replies View Related

Cisco Wireless :: Aironet 1260 Access Point Work Without Controller??

Dec 1, 2010

I would like to buy Cisco  Aironet 1260 Access Points, i just want to use them independantly so   i want to know do they work without the Wireless LAN Controller? or i  have to have the controller for them to work? they will be in different locations so i cant have a controller per each location.

View 9 Replies View Related

Cisco Wireless :: C1140 - How To Enable EAP-FAST / LEAP (with And Without CCKM) With WDS

Mar 11, 2012

I have a configuration AP & WDS (with AP):
 
#show version
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(25d)JA1, RELEASE SOFTWARE (fc1)
...
ROM: Bootstrap program is C1140 boot loader
BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)

[code]....
 
When I try to connect to WPA-ENTERPRISE or WPA-PSK - connected, but when I try to connect ot CCKM-ROAMING or WPA-ROAMING using EAP-FAST or LEAP (with or without CCKM) - connection failed.
 
Notice: In the current configuration, if client use LEAP (without CCKM) and AP work without WDS - WPA-ROAMING is worked correctly. But if client use LEAP (without CCKM) and AP work with WDS - WPA-ROAMING is not working.

View 10 Replies View Related

Cisco Wireless :: Using AIR-AP1231G-E-K9 As Repeater?

Apr 24, 2012

I have an AIR-AP1131AG-E-K9 running as root AP with three SSID's (mbssid), all WPA-2 PSK, IOS 12.4(25d)JA Now I would like to use an AIR-AP1231G-E-K9 as repeater for one of the SSID's (all three are AFAIK not possible), IOS 12.3.8-JEE(ED) So only one SSID is used.

I use exactly the same shared secrets and security settings on both devices, on the repeater the SSID is designated as infrastructure-ssid.Unfortunately I have the problem that the repeater AP cannot associate with the root AP.I have verified that aironet extensions are enabled, same security settings are used and checked many sites on the net which describe how to configure a repeater AP.  Is there any incompatibility between these two APs? I have two of the AIR-AP1231-G-E-K9 APs available, do I need to use the same models?

View 2 Replies View Related

Cisco Wireless :: Adding A Second Ssid Air-ap1231g-a-k9?

Jun 20, 2012

Version 12.3  I currently have an open authenication customer network, I would like to add a second securt ssid for my sales department, is this possible, how do I do this, the more specific the better .

View 1 Replies View Related

Cisco Wireless :: WLC 2504 Works With AIR-AP1231G-E-K9 And AIR-BR1310G-E-K9?

Feb 3, 2013

Does WLC 2504 works with AIR-AP1231G-E-K9 and with AIR-BR1310G-E-K9 after I upgraded form AP to LAP the AP ?

View 4 Replies View Related

Cisco Wireless :: AP1231G - Failed To Add Device To WCS Reason

May 10, 2012

I am trying to add an AP (1231G)  with autonomous code (Version 12.3(8)JEC2)  to WCS (v7.0.172.0).  I recieved the following error:
 
Failed to add device to WCS Reason: Unified AP with same MacAddress already exists in WCS. Remove Unified AP first.

View 9 Replies View Related

Cisco Wireless :: Does VWLC Support AIR-AP1231G-A-K9 Platform

Mar 6, 2013

Does the Cisco vWLC support the cisco AIR-AP1231G-A-K9 platform?

View 4 Replies View Related

Cisco Wireless :: Radius Server Authentication AIR-AP1231G-A-K9

Apr 30, 2012

Below is he output from debug radius authentication from my AP.
 
I can see request is forwarding from AP to radius but Radius is not sending any response.Not sure why its not responding.
 
I also did not under stand few out outputs also
no sg in radius-timers and
RADIUS/DECODE: parse response no app start; FAIL
what does it mean.
 
I  restarted radius server , changed secret key but no luck.
 
019639: May  1 16:15:08.727: RADIUS:  User-Name           [1]   32  "host/3KYGRH1.idcap.intdata.com"
019640: May  1 16:15:08.727: RADIUS:  Framed-MTU          [12]  6   1400
019641: May  1 16:15:08.727: RADIUS:  Called-Station-Id   [30]  16  "0012.01d6.f691"
[Code]...

View 4 Replies View Related

Cisco Wireless :: Strange Power Failure With AIR-AP1231G

Mar 25, 2012

I'm having the following issue with a couple of 1231's.
 
Some overall config info first:
 
This is a small office with 2x Catalyst 2950 (24-port, no PoE) switches and 4 AP1231G (autonomous). The APs get PoE from a PWRINJ3 each. The injectors are powered by the AP power supplies. Injectors and power supplies are mounted in the patch closet.
 
The 2 switches are connected together over 4 ports (20-23 on each switch), these ports are set to 1Q Trunk mode.
 
The APs are connected to the switches, 2 to each switch, on port 1-2. These ports again are configured as 1Q Trunk.
 
APs are connected to the switch as follows:
 
   [switch] <- patch cable-> [injector] <- patch cable -> [patch panel] <- static cabling -> [outlet] <- patch cable -> [AP]
 
All this has been working without problems for a number of years.
 
A few weeks back, AP2 did not restart after a power cut (everything else did). All LEDs are off, port on switch has no LEDs lit. I did not get around to investigating this furtehr until last week. I unmounted (failed) AP2, took it to the spot where (working) AP3 hangs, and plugged it to the cable of AP3. AP2 came to life immediately. I unplugged it and plugged AP3 back in, which restarted immediately.
 
So I suspect a power supply issue on AP2. I took the injector and power supply that fed AP2 out of the patch closet. When connecting AP2 directly to the power supply, it came to life immediately. So I figure the injector is defective.
 
On the same day, I notice AP4 is also dead (again all LEDs off, no idea how long, could have been that day or could have been a few days - it has definitely been working after the power cut that appeared to have killed AP2).
 
So I order 2 new PWRINJ3s and for good measure 2 new power supplies. Later that day, I took the injector and power supply that fed AP4 out of the patch closet. When I try this combination (AP4, injector4 and P/S4), and connect it to a different wall outlet (and therefore a different port -16 - on the switch) IT WORKS! Should have triggered questions, but did not immediately.
 
Last Thursday I got the new injectors and power supplies. So I take one of each, hook them upto AP2 at my desk, and AP2 starts up. So I mount new injector2 and new P/S2 in the patch closet, put AP2 back in its place, connect all the cables - NOTHING. AP2 does not start. The "power" LED on the injecvtor lights up green, the "device status" LED remains off. I take AP2, new injector2 and new P/S2 to my desk, hook them upto a wall outlet (connected to switch port 17). AP2 starts immediately.
 
Meanwhile AP3 has (also) stopped working (no LEDs on at all). As far as I can tell, it stopped working after I briefly disconnected (and reconnected) the patch cable between injector3 and the patch panel in the patch closet. The LEDs on switch port 1 are off.
 
I have since tried to power cycle both switches (took power off both, waited a while, poewerd both back on). No change.
 
PS: the APs ran firmware 12.3(8)-JA until recently. AP1, AP3 and AP4 were upgraded to 12.3(8)-JEE after the the power cut that took AP2 out. THis is when I found out AP2 was dead. AP2 was still on 12.3(8)-JA. It was upgraded to 12.3(8)-JEE last week when it was on direct power on my desk.

View 3 Replies View Related

Cisco Wireless :: AIR-AP1231G-A-K9 - Replicating Setup Across Heterogeneous APs

Oct 17, 2012

I am trying now to deploy the setup that works on some APs and doesn't work on others.
 
For example, on an AIR-AP1231G-A-K9, the following setup works:

!
version 12.3
no service pad
service timestamps debug datetime msec

[Code].....

View 2 Replies View Related

Cisco Wireless :: AIR-AP1231G-A-K9 And Controller Based Environment With Prime NCS

Apr 15, 2012

I can't find any information that the AP1231G-A-K9 AP is supported in a 5508 Controller Based environment with Prime NCS.Could one of the experts confirm or deny?

View 1 Replies View Related

Cisco Wireless :: AIR-AP1231G-A-K9 Standalone Access Point- Disconnection

Jun 9, 2013

We have this access point AIR-AP1231G-A-K9 for mobile users. current version is c1200-k9w7-mx.123-7.JA4. Sometimes users are able to associate but not getting IP address from dhcp. It shows 0.0.0.0 for the particular client.

View 2 Replies View Related

Cisco Wireless :: AIR-AP1231G-E-K9 - Upgrading Autonomous Access Points To Lightweight Mode

Jun 6, 2013

I have AP AIR-AP1231G-E-K9 with iOS c1200-k9w7-tar.123-7.JA2 and I want to convert it to Lightweight Mode with iOS image c1200-rcvk9w8 tar.124-21a.JA2. First of all, is it possible? Because I tried to convert from tftp server command (archive download-sw /overwrite /reload tftp://ipaddress/image.tar) and I cannot see in the controller. (controller and aps are in the same network)

View 11 Replies View Related

Cisco Wireless :: Current IOS For 1260 AP?

Jun 12, 2012

What is the most current version oF IOS for the following Wireless AP(Aironet 1260)
 
Product/Model Number:      AIR-AP1261N-E-K9
System Software Filename:     ap3g1-k9w7-tar.124

View 2 Replies View Related

Cisco Wireless :: Aironet 1260 As Bridges?

Feb 2, 2012

Is it possible to create a wireless site to site link using 1260 access points as bridges (like the 1300 series)?
 
Also if so, can you use 11n channel bonding on the bridge link?
 
I need to link 2 buildings together wirelessly approximately 70 metres apart.  There is direct line of sight between them.

View 10 Replies View Related

Cisco Wireless :: Antenna Separation For AP 1260?

Oct 24, 2012

We are installing 1260 Access Point (AIR-LAP1262N-E-K9) with 2 sets of external antenna:AIR-ANT2460NP-R (2.4Ghz, Patch Wall-mount, 6dBi Directional) & AIR-ANT5160NP-R (5Ghz, Patch Wall-mount, 6dBi Directional).What would be the recommended separation of the 2 antennas if they will be mounted beside each other?

View 1 Replies View Related

Cisco Wireless :: Upgrade IOS Image For 1260 AP?

Nov 3, 2012

i have cisco 1260 Access point with standalone ios  ap3g1-k9w7-tar.124-23c. i download new IOS to connect the AP to the controller the new ios is  ap3g1-k9w8-tar.124-23c.JA5.tar. upgrade th AP to LAP. is it just install ios like in router & switch by tftp?

View 1 Replies View Related

Cisco Wireless :: 1260 Can't Get IP Address And Can't Joint WLC

Nov 24, 2012

i have Cisco WLC 2504 & 1260 LAP.i connect the WLC to L3 switch & connect the LAP to another port in the same L3 switch.i configure DHCP on the same switch to provide ip for the LAP , but the LAP can't get an ip address and can't joint the controller.also if when i login to the LAP i can't enter the configuration mode.

View 6 Replies View Related

Cisco Wireless :: 1260 And 3500 - Bridge With Two AP's

May 14, 2013

So I'm going to bridge two Cisco AP's 1260 and 3500, which have an 880 router on each side.
 
(Currently I have a VPN set-up through the internet for the two locations to communicate) (Naturally they are currently in different subnets) Will absolutely change this and set up as one subnet. There is VLANs setup on each router (same VLANs)
  
VLAN 1
  
And
  
VLAN 10 
 
Everything is configured on the Routers and AP's for these VLANs (works flawlessly over the VPN). 
 
So now since I’m going to get rid of the VPN and set-up a bridge with two AP's, will having same VLANs across both routers be a problem? Will VLANs work OK through the bridge?
  
Besides using (IP helper address DHCP-IP) command on the non-root bridge side router to forward DHCP requests to the root bridge side router, Also I want to be able to route internet traffic on the non-root bridge side through the WAN port, and only route LAN traffic through the bridge..

View 1 Replies View Related

Cisco Wireless :: Configuring A 1260 Autonomous AP Documentation?

Mar 5, 2012

good docs for configuring a 1260 autonomous AP?

View 1 Replies View Related

Cisco Wireless :: How To Setup A Standalone Aironet AP 1260 Series

Sep 13, 2011

I'm new to the Cisco Aironet Access Point. I got a new STANDALONE Aironet 1260 series access point device. The part # AIR-AP1262N-A-K9. The shipping package did not come with any guide, CD, and power adapter. I searched the Cisco sites, but could not find appropriate manuals. I did find a getting started guide but not for standalone AP, it's for Controller-based AP. Question - where can I find manuals / guides to set up and configure my new standalone Cisco Aironet Access Point 1260?

View 3 Replies View Related

Cisco Wireless :: Aironet 1260 Series - Sending Station Has Left BSS

Oct 29, 2012

We have been having issues with random packet drops and or some sort of radio lockup which happens a few times a day. I have a test AP setup with a few clients only a few feet away and I see this combination of messages. Should I be seeing these clients drop off and then reconnect immediately? Granted these test clients are not passing much data but my assumption is that they would not become deauthenticated because of lack of activity? This setup is using a radius server for authentication. I tested it before with just WPA2 PSK and only had a few disconnected over a number of days, compared with many a day with the Radius.

View 1 Replies View Related

Cisco Wireless :: Aironet 1260 Series MAC Filtering In Autonomous Mode

May 13, 2013

Do we have Option to add MAC address of specific laptop or Mobile to connect to the Access Point in cisco Aironet AP 1260 series in Autonmous mode

View 4 Replies View Related

Cisco Wireless :: Mesh 1260 Ethernet Bridging With VLAN Tagging

Mar 18, 2012

I'm a little stuck with a 4400 7.0.220.0 + RAP 1550 + MAP 1260 Ethernet bridging issue. I'm using the VLAN tagging functionality and I'm finding that periodically a VLAN that I've tagged on the MAP will deregister from the backhaul and stop passing traffic. If I go into the Mesh tab on the MAP, select the wired interface, remove the VLAN from the list of tagged VLAN IDs and then add it right back to the list, its starts passing traffic again

View 2 Replies View Related

Cisco Wireless :: AP 1260 Configuration / 0 Clients Connected And Light Always Green

Feb 5, 2013

Recently I have installed and configurated an AP 1260, it has already IP, SSID, and ping to the router, but after install the antenna I open the web configuration and see that it has 0 clients connected and the light is always green, indicated as only is configurated with nobody connected.
 
Tha radio setting is up, 2,4 Ghz and 5 Ghz any issue with the antenna? or i need to configure anything else?

View 1 Replies View Related

Cisco Wireless :: 1260 Root AP De-authenticating WGB Clients After 6 Minutes Of Inactivity

May 27, 2013

i have 2 1260 Access points one is in root mode , one is wgb mode. Authentication is EAPFAST. There are 5 devices connected via WGB bridge to the rest of the network.

- If clients are sending some data , then WGB AP announces this client mac via IAPP to root AP and rest of the network sees them correctly
- If clients are "passive" , then after WBG AP announces them to root AP , they timeout after 6 minutes on root AP and obviously they are not pingable from the rest of the network. The only way to restore connectivity is to ping that device from WGB AP, then WGB AP announces via IAPP to root AP , then and only then they become visible from the rest of the network.

My question is related to this 6 minute timeout on root AP . Is it normal behaviour ?

View 5 Replies View Related

Cisco Wireless :: 1260 AP Suitable Replacements To The 1watt Luxul 2.4ghz Amplifiers

Jan 19, 2012

We’re deploying new WIFI towers at several of our vacation resorts and have decided to migrate from Wireless G to Wireless N access points. We currently have the following in each WIFI tower – Hotspot I’ve been researching and speaking to our partner pre-sales team, and have narrowed the choice down to deploying 3 x AIR-AP1261N-x-K9  at each of our towers. I have been unable to find suitable replacements to the 1watt Luxul 2.4ghz amplifiers we’re using, or really good N sector antennas to mount to the top of our masts. The 1260’s are all 802.af, so besides getting power injectors there shouldn’t be to much to think about.

View 30 Replies View Related

Cisco Wireless :: Is Aironet 1260 Good For Indoor LWAP Or CAPWAP Environment

Jul 12, 2012

Is Aironet 1260 good for indoor LWAP or CAPWAP environment? Do we need external antenna for the Aironet 1260 access point when using it indoor?

View 1 Replies View Related

Cisco :: AIR-AP1231G-A-K9 Management IP?

Nov 18, 2012

I have two dinasour APs that I need to fix. They are configured in bridge mode to bridge a few VLANs between two sites. Right now the management IP on BVI 3 interface doesn't work. Does it have to be on BVI1 for it to work? When I say "work" I mean I am able to ping it and use SNMP to monitor it.

View 1 Replies View Related

Cisco :: Ap1231g-e-k9 - Load New Bin Ios In Rommon Mode?

Jun 9, 2011

loading a new bin file onto a Cisco wirless access point ,the access point i have found is only in rommon stage

Access point model is  : ap1231g-e-k9.

View 4 Replies View Related

Cisco :: AP1231G-A-K9 Access Points / Very Slow Throughput

Jul 17, 2012

I recently setup our small office network using the following setup:

Cablemodem <--> router <--> 1231AP(role root bridge with wireless clients) <-> 1231AP(role non-root bridge with wireless clients)Code on both APs: 12.3(8)JEE.Office network generally has less than 3 wireless clients connected at any one time to either AP. AP's are a mere 50' apart; clients are all less than 30' from either AP; they all show excellent signal and connected at 54mbps signaling rates.
 
All is/has been working very well & very stable with the exception of speed. We have business class service from RR, approx 25mbps dl, 2mbps ul. Any hardwired client to the router switch ports are able to download at speeds averaging 23mbps. Any wireless client connected to either AP is never able to exceed download speeds of 5mbps. With no other wireless clients connected except my one test client, I was not able to exceed 5mbps throughput from either AP that I connected to.
 
I can confirm that the ethernet connection between the router and root bridge is up at 100mbps-FD and not showing any errors: [code]
 
Are these very slow thoughput speeds normal of this hardware combination?I did much searching/googling and found claims that by eliminating TKIP it almost doubles the actual wireless speeds our clients can obtain.

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved