Linksys Wired Router :: BEFSR41 Replacement For This Unit

Jul 28, 2011

My BEFSR41 died.  What is the replacement for this unit?  I do not need wireless.

View 1 Replies


Linksys Wired Router :: BEFSR41 Two Wired Routers In Non-standard Hookup

Sep 14, 2011

I have a home network with a wired BEFSR41 that, for a variety of reasons, MUST be manually IP configured (DHCP off).  All computers and other devices connected to it are manually IP configured.  I desire to add a device that cannot be manually configured, and needs DHCP.  I therefore need to daisy-chain two routers with the second one DHCP on (and manual IP connection to the main network).  The new device needs two-way internet access, but doesn't care if it sees any other current network devices.  I've tried several configurations, none seem to work.

View 3 Replies View Related

Linksys Wireless Router :: WRT150N Unit Disconnecting From Wired Connections

Jan 21, 2008

I purchased a WRT150N in early Dec 07.  I had a number of problems with the unit disconnecting from wired and wireless connections erratically anywhere from 1/2 hr to 10 hrs. of operation.  Troubleshoot thru Linksys chat.  Ended up replacing router.  Now  I am having the same problem with replacement router.  I've updated my windows XP, SP2, updated Ethernet driver and manually reconfigured router per Linksys advise.  Wife and my laptops have N adapters, primary PC is wired in. It seems to disconnect all connections at same time, totally random. The only way to reconnect is to power down router for a few seconds and then power up.

View 9 Replies View Related

Cisco Firewall :: Replacement Of Primary Unit Failed ASA5510

Sep 7, 2011

I have an issue bringing up my RMA'd primary ASA unit.
So what happened so far:
1. primary unit failed
2. secondary took over and is now secondary - active (as per sh fail)
2. requested RMA at Cisco
3. got ASA and checked that Lic (SSL), OS (8.2.2) and ASDM are at the same level as the secondary
4. issued wr erase and reloaded
5. copied the following commands to the new (RMA) primary unit:
failover lan unit primary
failover lan interface Failover Ethernet3
failover interface ip Failover 172.x.x.9 standby 172.x.x.10
int eth3
no shut
wr mem
6. installed primary unit into rack
7. plugged-in all cables (network, failover, console and power)
8. fired up the primary unit
9. expected that the unit shows:
Detected an Active mate
Beginning configuration replication from mate.
End configuration replication from mate.
10. but nothing happened on primary unit
What is a valid and viable approach in replacing a failed primary unit? Is there a missing step that hinders me to successfully replicate the secondary - active config to the primary - standby unit.
I was not able to find anything related to ASA55xx primary unit replacement with a clear guideline or step by step instructions.

View 10 Replies View Related

Linksys Wired Router :: BEFSR41 - Convert Wired Router To Hub?

Jun 16, 2011

I have an old BEFSR41 ver. 2 wired outer that I'd like to use with a motorola modem/router as a hub.  Is this doable?

View 2 Replies View Related

Linksys Wired Router :: Put A Password For BEFSR41?

Mar 16, 2011

I have the setup disk and want to set up a password for the router. Don't want to mess things up since the system was installed by a pro. How do I simply enter a password to be used to connect? 

View 3 Replies View Related

Linksys Wired Router :: BEFSR41 - How To Get Parameters Set Up

Oct 16, 2011

I have an AT&T Univese which is class G.  I want to run it in class N.Do you think plugging my Linksys router into the AT&T will give it to me(class n)?If so, how do I get the linksys parameters set up?  It giving wrong readings at its not connecting to the internet.

View 3 Replies View Related

Linksys Wired Router :: How To Set Up BEFSR41 To Work With DSL

Apr 1, 2011

I have just changed from cable to DSL. I have a LinkSys BEFSR41 router. I can't get my LinkSys BEFSR41 router to work with the DSL.

View 3 Replies View Related

Linksys Wired Router :: BEFSR41 - Unable To Log Into It

Jun 29, 2011

LinkSys BEFSR41 v3 4-port cable/dsl router
Ubuntu linux 11.04 'natty'
Verizon dsl internet connection
I'm unable to log into the router using the default   user/pwd  of blank/admin

View 2 Replies View Related

Linksys Wired Router :: BEFSR41 V2 - URL Will Not Load

Feb 14, 2011

My internet supplier is Comcast. I have a problem with a URL that will not load or I could not connect to that site. Comcast said it was my router that was probably the reason. I have not had any problem in the span of using this model and version before. Should I be looking for firmware upgrade or a new router? Operating system is MAC OSX 10.5. Using router to network 2 MACs.

View 5 Replies View Related

Linksys Wired Router :: BEFSR41 Can't Be Upgraded

Mar 27, 2013

I have a BEFSR41 that often goes brain-dead and the DHCP stops working.  I've tried three times to download and install new firmware but it always fails with a "pattern mismatch". My current firmware version is 2.00.02 and the file I am downloading is 2.00.04 build 8. Yes, I have verified that my hardware version is 4.3.The download file from this website is corrupted.

View 1 Replies View Related

Linksys Wired Router :: BEFSR41 V.3 Not Working With DSL

Feb 3, 2011

I have a Century Link DSL connection in my house and its working fine. I just got a new Linksys BEFSR41 v.3. I am trying to set it up for my PC, Xbox360 and BD player. Everything works fine when I plug them in to the DSL modem 1 by 1 but when I try to put the Linksys "in the middle"... nothing... So I'm pretty sure its not my DSL modem or connection.All the lights come up on the Linksys as they should (power, internet and the Ethernet) but for some reason it seems the internet not getting trought the router. When its connected and I pull up my internet browser I type and it takes me to the linksys config site. Without the router in the same address go to the Westell site as thats my DSL modem. Everything looks fine on the config site. All the correct IP, MAC, DNS address are there and still no internet access on any of my device.

View 1 Replies View Related

Linksys Wired Router :: BEFSR41 Can't See Web Configuration

Mar 23, 2012

I have problem with Linksys BEFSR41 ver.4.2 (Firmware Version: 2.00.4  )When i plug the cable on internet port  , router crash ,  can't see web configuration if get ip or to make some ather configure, only if unplag internet cable and restart the router i can see the web configuration .(i try to ping in local ip when crash but not responding )in my computer i have static ip ( and is direct connect with Linksys.i try it and with DHCP and plugent over LevelOne switch and over Cisco switch .[code]
in previous firmware they don't have in menu the server ip in wan pptp web configuration connection I have test with more than one  Linksys BEFSR41 ver.4.2   and all router have the same problemWith ather router  e.x. Cisco RVS4000 configured and working perfect in same network .

View 3 Replies View Related

Linksys Wired Router :: Replacing A BEFSR41 V2?

Feb 20, 2011

Comcast upgraded me to a 30 Mbps speed, and my trusty old BEFSR41 v2 doesn't cut it.    Cisco promotes wireless routers with a 1 Gbps ethernet, I would rather have a wired router, and use a WAP that I can unplug when I am not using it, since, for now, I only connect my work notebook wirelessly.    Most wireless routers also generate a lot more heat than a wired one does, and I don't need any more heat in my Houston home.A new BEFSR41 v4.3 is only 10/100 Mbps.  There doesn't seem to be any 1 Gbps wired routers for home use.  Will a new BEFSR41 give me 100% of the cable Dociss 3.0 speed, or would I need to get a 1 Gbps router to get the fastest throughput?  Or do I  only need to upgrade when the cable speed increases closer to 100 Gbps?If a 1 Gbps router is better, are there any simple business wired routers you could recommend?

View 1 Replies View Related

Linksys Wired Router :: BEFSR41 Ver 4.0 Disconnects

Jan 10, 2011

I have recently been having difficulty with my router. We have 2 computers and our xbox hooked up to the router and for the last few days whenever both of the computers are in use we experience frequent disconnects. It does not happen when it is just one computer and the xbox running, but as soon as both computers are in use it happens. The disconnects are very brief but extremely frustrating when I'm trying to play a game. I have the most up to date firmware according to the linksys site

View 3 Replies View Related

Linksys Wired Router :: Computer Not Detecting BEFSR41 V4.3

Dec 23, 2010

I am using a Windows 7 machine and I'm pretty sure the ethernet cable that I'm using is functional, considering that I'm using it to connect to the Internet right now.I've been trying to get my router going for a while now and I'm pretty sure I've tried everything that the internet has advised.  I've screwed around with the card speed, 10 mbps Half Duplex didn't work or anything.  I've manually set the IP and related stuff to 192.168.1.x and the works.  I've tried to manually run the setup, although that definitely didn't work considering that my computer can't even detect the dang router.  I've screwed around with the wiring and restarted my router and modem constantly.

View 4 Replies View Related

Linksys Wired Router :: Power LED Blinking BEFSR41 4.2?

Jan 3, 2013

i tried to upgrade my BEFSR41 model 4.2 to a newer firmware (FW_BEFSR41v4.3_2.00.4.5_20080603_code.bin) and got a blinking power led. I've tried to power cycle (several times), reset (several times, 30/60 secs), unbrick (several times) and still have flashing power led. My connection to the router looks like:

Request timed out.Request timed out.Request timed out.Reply from bytes=32 time<1ms TTL=64Reply from bytes=32 time<1ms TTL=64Reply from bytes=32 time<1ms TTL=64Reply from bytes=32 time<1ms TTL=64Reply from bytes=32 time<1ms TTL=64Reply from bytes=32 time<1ms TTL=64Reply from bytes=32 time<1ms TTL=64Reply from bytes=32 time<1ms TTL=64Request timed out.Request timed out.Request timed out.Request timed out.Request timed out.Request timed out.Request timed out.Request timed out.Reply from Destination host unreachable.Request timed out.(and offline until the next reset)

View 2 Replies View Related

Linksys Wired Router :: BEFSR41 - How To Change Password

Dec 21, 2012

I have just received this device from my deceased son-in-law and I need to know how to change the password. I do not know his and have no way of getting it.

View 2 Replies View Related

Linksys Wired Router :: BEFSR41 V1 Which TFTP Utility To Use?

May 30, 2006

I just have a quick question about the TFTP utilities that Linksys has. I tried to upgrade the firmware of my BEFSR41 v1 router using the TFTP utility for a BEFSX41 and it didn't work(I just hope I did it correctly).

So, the question is, are these utilities router-specific or they should work with other routers as well?

View 5 Replies View Related

Linksys Wired Router :: Use BEFSR41 In Bridged Mode?

Jul 22, 2009

I cannot find any explicit instructions on this.  Maybe they're calling it other things or implying it in other settings. 
How do I configured a BEFSR41 to operate in bridged mode?

View 4 Replies View Related

Linksys Wired Router :: BEFSR41 V4.3 Won't Connect To Internet

Nov 25, 2007

My cable modem works fine when not running through the router. However, when running through the router, the internet won't work.I tried unplugging the power and plugging it back in, as well as holding down the reset button for 30 seconds, but nothing worked.

View 8 Replies View Related

Linksys Wired Router :: BEFSR41 V4.3 Won't Log Incoming Nor Outgoing

Jul 15, 2010

I went a bought a brand new model V4.3. I had trouble installing it right from the word GO, but I did successfully get that acomplished, how ever one of the important features "logging of incoming and out going ip" won't work at all. I tried deleting the old logview.exe and rebooting  everything, then installed the "new" logviewer.exe. Well absolutely nothing happens. I have double and triple checked the setting in the router...logging is turned on,  the computer which has the logviewer.exe installed is the confirmed network ip i.e. and I can and do access the internet and all other computers on the network from that computer.

View 9 Replies View Related

Linksys Wired Router :: BEFSR41 How To Use A Packet Sniffer

Feb 10, 2011

how to use a packet sniffer for a night school class, but lack a hub at home. I only have a BEFSR41 Cable/DSL Router with 4-port switch.Is there any safe way to use active sniffing methods? Would the "Mac Flooding" I've heard about work, or do I need to find some kind of ARP poisoning method?Unfortunately while I do recall using Etherpeek around 10 years ago, it was at a very basic level and I'm out of practice.Is there a way to make the switch act like a hub?

View 1 Replies View Related

Linksys Wired Router :: BEFSR41 V2 Will Not Access Internet?

Sep 12, 2011

I have a BEFSR41 V2 router connected to a westell c90 modem and my provider is (AT&T). I have the modem set to PPPoE and DHCP enabled. I am using the router as a gateway. The router's status page indicates that is communicating with the modem. Release and renew works and I can detect the addresses of the modem. I just can't pull up websites. I am wondering if this router (12 years old) is not compatable with the service.

View 1 Replies View Related

Linksys Wired Router :: Befsr41 - 2nd PC Cannot Connect To Internet

May 12, 2011

I have 2 PCs and am using a Linksys befsr41 router.The first PC connects fine. The 2nd PC does not find a connection. BTW, when I connect my laptop to the 2nd port, it sees the connection immediately - the lights flash on the ethernet connection. No lights on the 2nd desktop PC.

View 2 Replies View Related

Linksys Wired Router :: BEFSR41 V3 Limited Or No Connectivity

Feb 22, 2011

i have a BEFSR41 v3 firmware v 1.05.00 - i have been usuing it for at least 7 or 8 years now - at one time i had 3 computers hooked up and they all three worked fine. Now i have 2 plugged into the router - both are xppro machines - the one i am now works with no problems. The other computer however has the limited or no connectivity problem.I used this router for years without any problems then one day this ip conflict message started to appear.Then one day i started getting this weird ip conflict message on both computers but only occasionaly - it never caused any problems - if you ignored it - it would simply go away.Then one day computer #2 got the limited or no connectivity message - i simple reboot fixed it. This solution worked several times. Computer #1 has never had any problems.
Sometime later the limited or no connectivity problem reappeared and this time a reboot did not work - i searched for a fix and decided to try changing the link speed from auto sense to 10mb half duplex - this solved the problem. This solution worked several times.Sometime after that the limited or no connectivity reappeared and after some searching i upgraded the routers firmware - this solved the problem.Sometime later the limited or no connectivity reappeared and this time i had to actually uninstall the NIC, reboot and then let it redetect the NIC and then the problem was fixed. This solution worked several times.Sometime later the limited or no connectivity reappeared and the previous solutions did not work to fix it - after searching for a fix i discovered that i could simply unplug the router and the plug it back in and this would solve the problem. This solution worked many times.Sometime later (wich brings us to 3 or 4 months ago) the limited or no connectivity reappeared and this time after searching for a fix i was able to fix it by updating the NIC drivers. Problem solved.This brings us to now - the limited or no connectivity has reappeared and none of the previous fixes correct the problem.When i originally set everything up it worked immediately out of the box.
DHCP is enabled - everything is set to obtain an ip address automatically.At first the event viewer reported The IP address lease for the Network Card with network address0xxxxxxxxx has been denied by the DHCP server {The DHCP Serversent a DHCPNACK message}.Now the even viewer just tells me it is using ip address 169.254.xxxxxx - (not the exact message but i didn't wanna go back and look)I have tried all of the previous fixes to no avail. I've tried shutting everything off and turning everything back on - i've tried resetting both the modem and the router - i've tried upgrading the firmware again. I even downloaded LELA and installed it on both computers thinking maybe it would detect and fix the problem buy no such luck. LELA simply tells me that computer #1 is working normally. On computer #2 when i installed LELA the first thing it did was try to find the router and it tells me it cannot find tried ipconfig /release and ipconfig /renew - i've tried it one after the other and also a reboot in between. I've tried clicking on repair in the LAN status - i've tried even tried different cables and switching ports on the router.

View 9 Replies View Related

Linksys Wired Router :: BEFSR41 How To Change Net-mask

Jun 3, 2007

I am using a BEFSR41 for my network. My internal netmask is The only options permitted in the dropdown list on the BEFSR41 is How to change the netmask?

View 9 Replies View Related

Linksys Wired Router :: BEFSR41 - Ports (2 And 4) Not Working

Nov 4, 2007

I have a linksys BEFSR41 V.2 router with four ports.  Ports #1 and #3 are working but the other two do not.  The diag. light just blinks rapidly.

View 4 Replies View Related

Linksys Wired Router :: BEFSR41 V4 Keeps Dropping Connection

Feb 4, 2013

For a number of months now, our Internet connection in an office of 5 computers, 2 Macs, 3 windows boxes (1 as dell  laptop) has experienced the connection of the Internet dropping off.The timing of the 'drops' is usually in the morning, when the Dell Inspiron M510 either boots up or wakes from sleep. Typically the solution is to turn off the modem, the router and switch, wait a few minutes, then turn the switch, the router, then the modem back on. Our connection via the modem is through AT&T, via a non-static IP addy.Our router is a BEFSR41, v4, with firmware up to date (circa 2006) It's becoming a daily chore now, just about, and is getting to be a bit of a headache on some days. 

View 3 Replies View Related

Linksys Wired Router :: BEFSR41 V3 With EZXS16W Not Working Together?

Jan 28, 2011

Working System: Arris -> BEFSR41 (dhcp) -> to four computers working fine.
As soon as I add the EZXS16W, computers plugged into EZX no getting internet. I have the back button depressed so it will work as a 16 port hub.
Not Working System:
Arris -> BEFSR41 Port 1 ----------------------------------------->EZXS16W ----> Computer (not working)
BEFSR41 Port 2 ->Computer (working) EZXS16W ----> Computer(not working)
BEFSR41 Port 3 -> Computer (working) EZXS16W ----> Computer(not working)
BEFSR41 Port 4 -> Computer (working) EZXS16W ----> Computer (not working)

View 5 Replies View Related

Linksys Wired Router :: BEFSR41 V3 Activating UPnP

Aug 11, 2007

I have a problem activating UPnP on my BEFSR41 V3 router. Whenever I try to activate it the 'admin' default administrator password no longer works. I have to reset the router in order to get back into the configuration web page. is there a version of the firmware which fixes this problem? I am currently at firmware level 1.05.00.

View 9 Replies View Related

Linksys Wired Router :: BEFSR41 V2.1 And Windows 7 / Vista Compatibility

Mar 18, 2010

I have a wired BEFSR41 V2.1 with 1.46.02 firmware.  It has been working fine with several varieties of W98SE, W2000, and XP machines over the years.When I installed VMWare a couple years ago, I noticed that the Vista VM didn't connect to the router. Since I was just testing some local stuff, I didn't bother to investigate or resolve the problem. Now I have a new HP Windows 7 machine, and it doesn't connect when connected to the router.  The diagnostic doesn't think the cable is plugged in. When I plug the DSL modem directly into the W7 box, I can connect to the internet just fine.  Also, I notice that when I plug the modem into the W7 box, there are some LEDs that flash on the network card inside the box.
However, when I plug the cable from the router (the same one that normally works fine with the XP machine) into the Windows 7 box, none of the LEDs on the network card flash.  This is probably a hint that things aren't working.
I tried disabling the IPv6 protocol.  That didn't work.  I have the latest firmware for the V2.1 according to the Linksys support site. I tried a different cable.  I tried several resets from the pinhole in the front of the router, several power cycles, and reboots of the W7 box.So I'm guessing that the BEFSR41 V2.1 with 1.46.02 is incompatible with Vista and Windows 7.  

View 6 Replies View Related

Linksys Wired Router :: BEFSR41 V3 - Dyndns Server Is Unavailable

Dec 29, 2011

I'm currently running a BEFSR41 V3 router with firmware version 1.05.0 It seems that there is no update retry if the dyndns server is temporarely unavailable. Is it possible to initiate an update via command line or is a new firmware update available to solve this issue?

View 1 Replies View Related

Copyrights 2005-15, All rights reserved