Linksys Wireless Router :: Can't Access WRT160n Setup Page

Oct 16, 2012

I have updated the WRT160n firmware and, since then, I couldn't access the setup page anymore. I could still use the router as a switch, but couldn't access the setup page and configure it as a router.

View 5 Replies


ADVERTISEMENT

Linksys Wireless Router :: WRT160N - Upgraded Firmware Now Setup Page Won't Open?

Aug 7, 2011

I was having problems with the speed being between 30-58 kpbs when going through the WRT160N router, whether its hooked up wired or wireless, the speed with both was extremely slow and wouldnt fully open pager or would take dsl day slow. I hooked up straight to modem and I got 100+ kpbs so I figured its not my ISP, so I read that upgrading my firmware might make it faster, so I upgraded and hit and held the reset button for 30 secs like it recommended but now the 192.168.1.1 wont open, I get a message saying it cant open this page

View 4 Replies View Related

Linksys Wireless Router :: Cannot Access WRT54G Setup Page

Jan 19, 2013

I have a WRT54G router that I have not used for many years, but now I need to use it again. I have connected it between my modem and PC, and I am able to get an internet connection on the PC, but I am unable to connect to the router's configuration page. I have tried resetting the router numerous times (holding the reset button 5 seconds, 10 seconds, even longer) to reset the IP address to the default 192.168.1.1 address, but still cannot access the page. The power LED is on and the WLAN and Internet LEDs are on, and the LED for the port my PC is connected to is on. The hardware version of the router is v3. I tried downloading the latest firmware, but without being anble to communicate with the router at the IP address I cannot update the firmware. How can I go about connectiong to the router's setup page? When using ipconfig, the Default Gateway appears to still point to my ISP's IP address instead of the router's.

View 9 Replies View Related

Linksys Wireless Router :: Cannot Access E1200 Setup Page

Nov 29, 2012

I'm able to connect to the internet through my E1200 router but I cannot access the router set up page. 192.168.1.1 doesn't work... I can connect to it just fine with my laptop however... so I changed it to 192.168.254.1 as per some internet instructions. Still can't connect via my desktop... Tried ipconfig /flushdns to no avail. Cleared the internet cache Upgraded the firmware (via the laptop) rebooted the computer rebooted the router... reset the router... After rebooting the router I can type in the username and password to access the router, but it never connects....

View 6 Replies View Related

Linksys Wireless Router :: Can't Access Setup Page WRT54GS

Sep 9, 2012

I need to set up a password for my wireless network, but every time I try to access the setup page, the router stops responding.  I've gotten as far as it asking for username and password, where I enter admin as the password....and then nothing.  The connection times out.  I really need to protect my network.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G - How To Access Setup Page

Apr 27, 2012

When I had DSL, my WRT54G was my DHCP master for my home network.  When I got AT&T U-Verse, their "gateway" became the DHCP master and also the wireless access point.  But the signal was not strong enough where I wanted to use it, so I hooked up the WRT54G again.  I discovered that if I connected the U-Verse gateway to the "Internet" port on the WRT54G Linksys, then my home network was split in two, which I did not want.  The WRT54G access point is physically somewhat distant from my wired computer, so I wanted to keep the U-Verse gateway as the DHCP master. (The U-Verse gateway is a router with four "computer" ports but no "Internet" port.)
 
I followed instructions on the Linksys web site, and using my wi-fi connected computer I re-programmed the WRT54G to be "Disabled" as a DHCP server.  Then I powered down and physically connected the U-Verse gateway to a "Computer" port on the WRT54G.  This solved my problem:  my distant wi-fi computer now has a good signal, and both computers "see" each other.
 
However, now I seem to have lost access to the WRT54G setup "web page."  Is it possible to access the innards of the WRT54G when its DHCP service is disabled?  Or would I have to reset the device to factory configuration and start all over if I wanted to make any tweaks?

View 3 Replies View Related

Linksys Wireless Router :: 1721 - Can't Access Setup Page

Jul 11, 2012

My internet is T1 by Verizon. My mom's company Siemens pays for our internet because she works from home as medical tech support on the phone. Okay so the T1 had to be laid out to our house underground I think because where we live, other brands of internet aren't available. The T1 goes from the box outside into our basement and hooks up to a Cisco 1721 modem. From the 1721 the internet goes out to a wireless router that is sitting right next to it. This wireless router is a Linksys WRT160N V2. We have several cables coming out of the WRT160N V2 to go to the first floor for hardwired connections, but one cable goes to the attic and connects to a second wireless router. The second wireless router is a Linksys E2000. We have several cables coming out of the E2000 that go to the 2nd floor to serve as hardwired connections.Okay so let me explain where things went wrong.

After a storm our power went out. Eventually the power came back on, but every now and then our internet would shut off for like half a day then turn right back on, so our internet was getting really really spotty. The [b]AL[/b] light on the Cisco 1721 would come on every time the internet went out. It was so bad that my mom had to get an aircard from verizon to get internet. So after two weeks of spotty service and arguing with verizon trying to get them to come fix the problem, they said try resetting your wireless routers because they might have "bad data" in the lines causing spotty connection. So we reset the wireless routers by holding down the reset buttons on the back. Well.. this reset all of the settings for the routers which Cisco facilitated set up, and now our wireless routers are out of warranty date so they can't set the wireless routers back up. However, we have copies of the online wireless router set up page, so we thought maybe we could just set them up ourselves.Well the problem is... We don't know how to connect to the wireless setup pages.. I read something on the internet about setting up wireless networks and to type 192.168.1.1 into our browser(Mozilla Firefox) and that would bring us to the wireless setup page. But the page does NOT ever come up.

Another way to find the IP address of our wireless routers would be to try going to the cmd and typing in ipconfig and using the Default Gateway IP address for the browser to connect to the setup page but that doesn't work out either.... Right now I unhooked the Linksys WRT160N V2 and hardlined the Cisco 1721 to the Linksys E2000 to a PC on the second floor because I figured it wouldn't work out if we had two wireless routers running at the same time. Currently the browser is taking me no where at all. It just says "Connecting..." but nothing is loading up at all.I tried hardlining from the Cisco 1721 to my mom's laptop, which is her work computer, and I got no response at all. I figured it might just be her work computer that was messing up and not allowing her to hardline into the 1721 so I tried hardlining the Cisco 1721 straight to the PC desktop on the second floor(we have no other laptops other than my mom's work laptop) and nothing went through. Then my dad says the Cisco 1721 has been configured so it doesn't direct connect, meaning that it has to go through a wireless router.

View 4 Replies View Related

Linksys Wireless Router :: Need Access E1000's Web-based Setup Page

Jan 6, 2012

I have a Linksys E1000 wireless router, and I seem to have either written down the password incorrectly or am using the wrong one. Regardless, I can not access the web-based setup for the router. Is there anyway to reset the username and password for it?

View 3 Replies View Related

Linksys Wireless Router :: Wrt54g2 - No Access Through Wifi To Setup Page?

Jul 16, 2011

I bought wrt54g2 several years ago and everything worked fine until this week. I got trouble with this router now.All the computers at my home couldn't access to this router even just connect to router's setup page at 192.168.1.1. The only way go to setup page through LAN Cable .I'm afraid maybe there's interference channel with my neighbor, then I did some change to router channel already, but the result same. I still couldn't access to the router through WIFI
 
Fyi, I did upgrade the firmware with the latest one and all the computers distance to the router not more then 5 m and in the clear area

View 6 Replies View Related

Linksys Wireless Router :: E900 - Upgraded Firmware / Changed IP Now Cannot Access Setup Page

Jun 6, 2012

I bought E900, accessed setup thru 192.168.1.1, upgraded its firmware.. then changed router's IP, it reboots, then went blank, I cannot access the setup page anymore?

View 9 Replies View Related

Linksys Wireless Router :: E3200 - Cannot Access Setup Page Wireless Or Wired

Nov 7, 2011

I finally decided to go with a e3200 yesterday and picked up one at Walmart. Last night I went to hook it up and had no luck setting it up. Now I have able Internet with a phone VoIP service. After trying to connect several ways, all the router wants to do is sit with a flashing power light. I cannot access the setup page wireless or wired and have tried several methods I found last night.

View 1 Replies View Related

Cannot Access Router WRT54GX Web Page / Setup Page?

Jul 28, 2011

i need to get into the web page because i need to open my XBL nat and when i type in the password to get into the routers page i get a blank screen

View 2 Replies View Related

Linksys Wireless Router :: WRT160N V2 - Setup Cd Won't Get Past 25%

Jul 26, 2012

setup cd won't get past 25% and says not connected to the int! but yes i am .Also tryin to bridge with ATT PACE 4100n crapp!

View 2 Replies View Related

Linksys Won't Let Me Access Its Setup Page Now

Aug 29, 2012

when i was on my linksys setup page 192.168.1.1 i accedently disabled wireless web access now i cant undo it so now i cant use wifi

View 1 Replies View Related

Linksys Wireless Router :: WRT160N V3 - Cannot Connect To Setup Webpage

Apr 20, 2012

Every time I try to connect to the admin page of my router, I get "The connection to the server was reset while the page was loading."  This happens with FIrefox 11, and started when I upgraded to 8 or 9.  A machine running FF 3.6 does not exhibit this problem; I get right in.  What IE 9 says is "Internet Explorer cannot display the webpage" (after complaining about the expired certificate).
 
I ran Wireshark to see if I could learn anything, but all I could figure out was this: https handshake was OK. First TLS packet is received by router, which then immediately issues a reset and ends the connection.  I don't know why.
 
have I got a screwed up configuration (or router)?

View 5 Replies View Related

Linksys Wireless Router :: WRT160N Setup As Adapter To Connect Printer To Network?

Jul 30, 2011

How do I setup a WRT160N as a wireless adapter to connect a wireless printer to my network? I do not use the wrt 160 as a router because I have an AT&T router for u-verse connection. Also, I physically cannot wire the printer to the main router (opposite corners of the house).  

View 2 Replies View Related

Linksys Cable / DSL :: X2000 Access Web Based Setup Page (Mac)?

Apr 26, 2012

I tried already several times, may be I entered already a name and password, can`t remember. Anyhow this time I was well documented to start again, but after 192.168.1.1, leaving 'name' blank, and password 'admin', this was quoted as wrong name and/or password. What to do to be able to continue now?

View 2 Replies View Related

Linksys Wireless Router :: E2500 Cannot Connect To Setup Page

Apr 21, 2012

I can't connect to my setup page [url]... I get to the page that says..."There is a problem with this website's security certificate." Then I click the "continue to this website (not recommended). After this it will not connect 
 
Tried with IE9 and Firefox 11
 
Firefox says "The connection to the server was reset while the page was loading."
 
Internet still works. PC is connected directly to router. Tried different port on router. Tried installing CiscoConnect.E2500.1.4.11299.0,0, but it fails saying there is no router connected to PC. Like I said I am on the PC now, wired to router and have internet access via cable modem connected to router. I can see my ireless printer on the network also..

View 2 Replies View Related

Linksys Wireless Router :: EA-4500 Can't Login Into Setup Page

Oct 26, 2012

I'm trying to login to my EA4500 setup page. I have the "cloud connect" firmware and when I'm redirected to the "Linksys Smart Wi-Fi" page in my browser, I attempt to login as usual.It accepts my login name and password, and then I get a page that has a rotating graphic and it says "waiting..." It eventualy times out and takes me back to the login screen. I've tried to reboot my router and that doesn't work. I've also disconnected the internet connection from the modem, and entered the router main password, and that gives me the same response as if I tried to connect via the cloud.

View 9 Replies View Related

Linksys Wireless Router :: E4200V2 Can't Get To Advanced Setup Page

Apr 3, 2012

I just installed new E4200V2.  After completing software install, everything appears to be working fine, except that I can't get to the advanced setup page, either through Cisco connect software or from the web page utility.  Either way, the advanced settings web page never finishes loading.  I am using the correct login information for the web page utility.  It accepts the username "admin" and password, but never loads.  Browser just sits there.  Browser status bar says "waiting for http://192.168.1.1. 

View 3 Replies View Related

Can't Access Router Setup Page

Mar 22, 2011

i need to do the following:

-go to routers startup page

-log in

-look for my WAN MAC address

it seems so easy, but i keep getting instruction to do things like type in different numbers into my browser which never work.

View 14 Replies View Related

Linksys Wireless Router :: E4200 Accessing Modem Setup Page?

Dec 4, 2011

if it is possible to access a modem setup page with a E4200 router? My router is on 192.168.254.200 and modem(WAG-200G) is on 192.168.254.100, ethernet cable is on internet port on the e4200 and on port1 on the modem. Modem is set is bridge and I set up a ppoe and dhcp on router. Everything is ok, except that i can not access modem setup page to see adsl conection speed and settings.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G V8 / Unable To Navigate The Basic Setup Page

Jan 14, 2008

I have been trying to change my password and all the settings on my WRT54G V8 router today because I forgot the password, and I can't seem to navigate the Basic Setup page. I can log in (most of the time) after resetting the router, but whenever I try to click on a different tab (like "Wireless", or "Security") it comes up with the page saying "This Page Cannot Be Displayed."  I'd like to be able to put a password on it (which I have successfully done before on this router) because I live in a college dorm and would like to keep my internet from being bogged down by other people using it. 

View 9 Replies View Related

Linksys Wireless Router :: WRT310N / Accessing Configuration Web Based Setup Page

Apr 9, 2012

I have Verizon FIOS internet/wireless router and then a WRT310N wireless router connected to it thru Ethernet cable.  I want to disable DHCP in the Linksys, but when I try to access the set up page at address 192.168.1.1 the Verizon router set up page shows up.  I've tried to connect the router directly to the computer, but it needs the internet connection from the Verizon router.  How do I get to the set up of the Linksys at the same time the Verizon is using the same address?

View 5 Replies View Related

Linksys WRT160N - Can't Connect To Router Setup

Feb 26, 2013

for the past couple of hours i've been trying to setup my router (Linksys WRT160N).When i set up all the cables, like it is in this picture:

[URL]....

View 1 Replies View Related

Linksys Wireless Router :: Using WRT160N V2 As Access Point?

Mar 22, 2013

I have a FIOS setup with their Router/modem providing DHCP and Wireless routing.  The problem I have is that I have a mix of older equipment and newer equipment.  The newer equipment is capable of supporting WPA2, the older is not.  I would like the benefits of WPA2, but still would like to at times be able to use the older equipment.My solution was to use a WRT160N v2 router that I had as an access point and it also gives me switch capabilities for wired systems as the FIOS router in on a different floor than the Linksys router.  Wired access works just fine and the wireless worked fine until just recently.Since both routers have the same default IP addresses I changed the Linksys to a different static IP and turned off DHCP.  I left all of the other defaults the same.  I set up the Linksys for WEP and created the key for security.  Everything worked fine for the better part of a year, but recently I am having problems where some of the computers cannot find the network or find it then lose connection.

View 9 Replies View Related

Linksys Wireless Router :: WRT160N Remote Access

Mar 23, 2010

  Even when I disable remote access, people still can get to my router login by typing my external IP.  Is there anything I can do to stop this?

View 5 Replies View Related

Linksys Wireless Router :: Which Access Point To Be Used With WRT160N

Jul 28, 2011

I have a Router WRT160N and need to connect an Access Point using a wireless bridge (i.e. cannot use cable between router and AP). Which Linksys Access Point model is recommended to use with this router?(No I dont want to use another WRT160N with DD-WRT!)

View 1 Replies View Related

Linksys Wireless Router :: Can't Access Internet Using Wrt160n

Dec 25, 2011

While trying to add my kindle fire (unsuccessfully) I lost all internet connections, now my laptop won't connect.  I reset the router and and can see my wi-fi account but when I try to use on my PC and laptop it won't recognize it.

View 3 Replies View Related

Linksys Wireless Router :: Use WRT160N As Access Point?

Aug 3, 2011

I have a WRT 160n I want to use as an access point.  The cable company has provided the main router so I want to use the 160 as the access point.  I have a switch attached to the router and have the 160 attached to the switch.  I can ping and access the 160, however there signal strength has not changed and is still extremely low.  I know that the strength on the router is very good when I plug it in to the cable modem.

View 1 Replies View Related

Linksys Wireless Router :: WRT160N - Access To IP Address 192.168.0.1

Sep 16, 2012

I have Linksys router model no. WRT160N, which I have been using for three years.  I need to add two iPads to my router but I do not know the network password.  I am trying to access the router IP address 192.168.0.1 to find out the network password, but when I put HTTP://192.168.0.1 in my browser, I receive the message: Internet Explorer cannot display the webpage.  How can I find out the network password? 

View 9 Replies View Related

Linksys Wireless Router :: Setting Up Access Point With WRT160n?

Sep 19, 2011

I just bought a Linksys E4200 wireless router. I have an old Linksys WRT160N wireless router.  I would like to setup the WRT160N downstairs to wire the DirecTv box and PS3 to it. Then wirelessly connect to the E4200 upstairs where our modem is connected.  Can the WRT160N be used as an access point to do this or do I need other equipment?

View 1 Replies View Related

Linksys Wireless Router :: WRT160N - How To Access Web-Based Utility

Dec 10, 2008

I am having trouble logging in on my wireless router and when i put "admin" (WITHOUT QUOTATIONS) on the password, the same prompt kept on coming for three times and after that the message says "401 Authorization Required" (WITHOUT QUOTATIONS). I don't get though, i installed the wireless router just after i change admin and my password into (******).

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved