What happen to my router linksys e1200, after i update the firmware to the latest version "Access Restrictions" is change to "Access Policy". how can i revert it back to "Access Restrictions" do i need to downgrade the firmware?
I had a E1200, I read the articles from the support about the routers, I think the "access Restrictions" has more flexible to setup on for the parental control, after chated to cisco support person online, I was told that the E1200 v2 has this "access restrictions" function, and I wan convinced to purchase from them. I did. I got the E1200 v2 recently, however, after I installed the CD and found there is no "access restrictions" tab, instead the "access policy" is still there. by the way the firmware is 2.0.02 now. How to get the "access restrictions" from setup? I've chatted with cisco support person twice again, but nobody can fix the problem, one suggested to restart and reinstall the CD. I uninstalled the software, restarted the computer and reinstalled the CD. same problem, no tab of "access restrictions".
I just bought a factory refurbished E1200. The label on the bottom says it is a Version 2 model. When I purchased it, it was loaded with 2.0.02 firmware but I upgraded the firmware to 2.0.04.My problem is that I'm trying to setup MAC address-based restrictions thru the manual/web-based setup and when I click on the "Access Restrictions" tab, I only have simple "Parental Controls" and not the advanced "Internet Access Policy".Is it possible that I have a mislabeled V1 device? If that is the case, how is it that I was able to upgrade the firmware using firmware from the V2 downloads section.
Do V! and V2 units use the same firmware but more importantly, how do I upgrade the built-in software so that I have the advanced "Internet Access Policy" controls?
I'm having problems with the access restrictions feature on the WRT600N. I do have the latest firmware upgrade, which was released in 2008 I believe. Anyways whenever I totally block a PC from the internet either by MAC or by IP, it affects the internet on the rest of the house. Logins to sites do not work right. Logouts from do not work right. Different features of different sites will not work properly. There also will be a lag sometimes when entering the url for a new site. But as soon as I turn the access restriction off, everything goes immediately back to how it should be working.
I have access restrictions set up for certain wireless devices in my home that the kids use to kick them off at 11 pm and keep them off all night. where I am running into a problem is I want to block these same devices from downloading anything without my permission my son downloads everything he sees, Comcat has already threatened to kick us off their service if we go over 250 gb bandwidth use in a month again. so I want to configure something in the router that will block all downloads for specific wireless devices. with the access restrictions I have set up I used the mac address not just the ip so they have no way around it I constantly monitor what is connected. I am using the stock firmware as well
I decided to limit some Internet time for the kids going off this router (which has been working great since set up) but my Access Restrictions tab is missing. I have an identical router at my work place, same version/firmware, same settings, but the one at work does have the tab.
I am trying to get a cell phone to have access to my LAN from 3am to 7am. I gave the policy a name, allowed access, checked everyday and the time 3a to 7a. Under edit list of PCs, I entered the MAC address of the phone, and I have also entered the MAC address of the phone on the wireless>edit mac filter list, though didn't know if I should.
I keep trying to set access restrictions for my wrt54g router for time. There is no 12 for time so I'm selecting 11:55 pm to 6am but I keep getting an error message of, "end time must be bigger then begin time." I get this no matter if I select 9pm, 10pm, etc.
I am using a WRT150N with firmware v1.00.5. I have a Linux setup with Squid connected to the network with the gateway 192.168.23.254. The WRT150N has a gateway of 192.168.23.1. The WRT150N is also connected to an Apple Base Station which serves as the Access Point for WiFi users.Squid limits access for IP addresses listed under the .254 gateway. But once I change my gateway to 23.1, everything is accessible. I want to block sites as well on the WRT150N. But every time I try to put a new Access Restriction, it doesn't work.
I want to set up access restrictions to one MAC address (my kid's machine) basing on week days. From Su to Th allow less access time while during Fr-Sa afternoons access time should be longer. The question is how to program it in router. I know I can set rules with "allow" and "disable" keyword, but I don't know rules preference. When I set (Su-Th 6-21) allowed access time then router automatically denies defined machine internet access outside this time range. The problem is in the power of thus calculated denying time. I want to allow more access time in weekend, so I hoped if I can simply add "Fr-Sa 6-22:30 allowed access time" rule. I hoped that router will regard explicitly set time over inexplicitly set time but it appears it is not so. What are their preferences/priorieties, iis it possible to stack more rules affecting one MAC address or it is so simple that the first rule "rulez"? Is it possible to set more than one time rule affecting the one machine?
Recently switched from WEP to WPA2 on the router and let it run a few days. Everything was copacetic.
Then decided to implement the following access restrictions:
1 - Target MAC based, internet blocked from 9-11:55 PM (why won't it let you block from 9PM-7AM ;-( ), blocks son #1's laptop, Kindle
2 - Target MAC based, internet blocked from 10-11:55 PM, blocks son #2's Kindle
3 - Targets IP Address range based (192.168.1.0 - 192.168.1.254), across all devices blocks several porn sites all the time
I can get on a play games online but when we start watching video with all 3 restrictions enabled, it will eventually disconnect (can take 1-5 minutes before it happens). Rebooting XBox usually reset connection, but it would happen again eventually. After disabling all restrictions, disconnects completely stopped.
Is it not possible to have Access Restrictions in place on a WR54G and still stream video?
I 'd like to use the access restrictions capabilities of the WRT610N v2. Unfortunely the "Access Restrictions" menu is missing in the admin GUI; I 've got all the others : "Set -up", "Wireless", "Security", Storage, Applications and Gaming, Administration and Status. I've checked the Firmware already and i'm using the very last one available on the cisco web site. I also noticed that I do not have the "Linksys by Cisco" text on the upper left corner as one can read on user guide but just "Cisco".
I have been looking into this router, I would like to know if I can enable Parental controls or access restrictions to block a MAC or IP address; from 03:00 AM - 06:00 AM ?Instead of Midnight to 6:00 am.My E4200 works just fine, Just would like to know if the EA6500 Can do that ?
I have E1200 router and a Motorola cable modem. I can access the router and internet with a wired connection but when I unplug the ethernet cable I no longer have internet access. I can connect to the router. I have another computer and xbox that are running wireless with full internet access.no problem.
Internet policy access on my Linksys E3000. I am trying to block facebook.com to a particular ip address in my office. This what I did. Logged in to control panel clicked on access restriction. Clicked on add. Gave it a name. Clicked the applies to drop down box and selected by ip address. Unchecked the block all internet access. Typed facebook down in the window below. Saved.Not blocking access.
The Internet Access Policy feature of my WRT610N router doesn't appear to work, at all, zip, nothing, nada. I have setup the feature todeny access to one of my laptops for everyday 24 hours a day, but it can still use the net...
Okay so my friend recently bought a Linksys E1200 Wireless-N Router. We set it up the other day and it all appears to be functioning just fine. The only problem is when we log into her wifi it says "No Internet Access". I'm moderately okay when it comes to computers but not expert and I'm horrible at the whole wifi router thing. Through my laptop I've done a Windows Network Diagnostic to see what was wrong and it says that my "computer is correctly configured but the device or resource (DNS server) is not responding."
I'm able to connect to the internet through my E1200 router but I cannot access the router set up page. 192.168.1.1 doesn't work... I can connect to it just fine with my laptop however... so I changed it to 192.168.254.1 as per some internet instructions. Still can't connect via my desktop... Tried ipconfig /flushdns to no avail. Cleared the internet cache Upgraded the firmware (via the laptop) rebooted the computer rebooted the router... reset the router... After rebooting the router I can type in the username and password to access the router, but it never connects....
I have a Linksys E1200 router.My problem is I have installed a camera system that allows remote viewing.I cannot access the system through the E1200 I am not very knowledgeable in net working.What do I need to do to access the DVR from a remote computer?
Trying all week to get my E1200 setup as an Access Point with my AT&T U-Verse 2WIRE Modem. [code] It just never seems to work correctly. It will connect for a second or 2 and then jam up. My ultimate scenario would be to have the E1200 just act as a wireless access point and have the 2WIRE do the rest: firewall, DCHP, etc.
I have a secondary router (E1200) on my home network, connected LAN to LAN. I use it mainly for wired connections, and it does work for that. But when I try to access this router through the IP address, I get a page that says only "ACT_IDLE". Occasionally, I am able to access, but I've found no pattern to when the router is accessible and when it is not...mostly not.
I am trying to set up an access policy on my WRT400N. Whenever an access policy is enabled, all internet acess is completely blocked. This occurs irregardless of what the access policy is supposed to block. Even a blank access policy that allows access to everything and doesn't have any computers registered still blocks everything. How do I get it to stop completely blocking internet access?
I have WRT150N, with firmware version 1.01.9 and I can not get the internet access policy to work.Here are my settings: PC list is configured through IP range as follows:Even if I deny internet access completely, I can still access the internet.