Linksys Wireless Router :: WRT160N - Upgraded Firmware Now Setup Page Won't Open?

Aug 7, 2011

I was having problems with the speed being between 30-58 kpbs when going through the WRT160N router, whether its hooked up wired or wireless, the speed with both was extremely slow and wouldnt fully open pager or would take dsl day slow. I hooked up straight to modem and I got 100+ kpbs so I figured its not my ISP, so I read that upgrading my firmware might make it faster, so I upgraded and hit and held the reset button for 30 secs like it recommended but now the 192.168.1.1 wont open, I get a message saying it cant open this page

View 4 Replies


ADVERTISEMENT

Linksys Wireless Router :: E900 - Upgraded Firmware / Changed IP Now Cannot Access Setup Page

Jun 6, 2012

I bought E900, accessed setup thru 192.168.1.1, upgraded its firmware.. then changed router's IP, it reboots, then went blank, I cannot access the setup page anymore?

View 9 Replies View Related

Linksys Wireless Router :: Can't Access WRT160n Setup Page

Oct 16, 2012

I have updated the WRT160n firmware and, since then, I couldn't access the setup page anymore. I could still use the router as a switch, but couldn't access the setup page and configure it as a router.

View 5 Replies View Related

D-Link DIR-655 :: Firmware Upgraded Now Cannot Access Router Page

Dec 27, 2011

I upgraded my router from version 1.2 to 1.35NA, through the Tools / Systems page on the router (uploaded the bin file).  I am connected to the router via a wired connection.

During the upgrade, the message said I wouldn't be able to access the webpage until 75 secs. I watched it count down the seconds and then when it refreshed, I could not get to my routers page:  192.168.1.2

The DLink Router is connected as a pass through router to my FIOS router, so that I can use the wired ports and I use the DLink as my wireless router (fios router wireless strength was poor).

All the lights on the router are working as though everything is ok. I am still connected to the Internet, so it appears that the pass through of my wired ports is still working after the firmware upgrade, but wireless is not. Not surprising. I expect I may have to upload my settings (which I did save), but since I cannot get to the routers page, I feel a bit stuck.

two more bits of into.  I also tried getting to 192.168.0.1, which might be the default?  and I cannot get there either.  My Fios router is on 192.168.1.1 (and as mentioned, the DLink should be at 192.168.1.2). Fios Router reports that the 192.168.1.2 port is inactive.

View 5 Replies View Related

Linksys Wireless Router :: WRT160N V2 - Open Up Ports To Get Open Connection On Xbox

May 23, 2012

I have the port numbers but do not know how to proceed from there.   Router is a WRT160N V2.

View 9 Replies View Related

Linksys Wireless Router :: Ea4500 - Upgraded Firmware / Need To Associate With Smart Wifi Account

Jan 2, 2013

I just setup my new Cisco EA4500 and upgraded to latest firmware and signed up for my account.Local access to the router works fine and I see the Smart Wi-Fi admin/config interface However when I try to go to the following site: url...To access Linksys Smart Wi-Fi Tools, your router <em>requires</em> the <a href="url...Series Linksys Smart Wi-Fi Firmware</a> and you will need to associate your router with your Linksys Smart Wi-Fi account.On a computer or device connected to your router, open url... and follow the instructions. This requires that you enter the router password so have that ready.

However I see no way to perform the association step - my account exists and my router is configured.I am doing all this behind this router wi-fi network not remotely.

View 4 Replies View Related

Linksys Wireless Router :: Open Nat On A WRT160n V3?

Jan 4, 2012

I have all the ports open necessary and i have upnp enabled.  my modem is a webmaster DPC2100 series. 

View 2 Replies View Related

Linksys Wireless Router :: Open Ports 443 And 80 On Wrt160n V3?

Jan 20, 2012

How do I open ports 443 and 80 on my wrt160n v3 router?

View 1 Replies View Related

Linksys Wireless Router :: WRT160N Cannot Open As An Admin

May 7, 2012

I need to get to my web admin page, but I cannot get into my router to do so.IE tells mt that there is a certifacte error, and then gives me the option of going in anyway.When I select that option, nothing happens, and the same IE warning page remains.I am plugged directly into an e-net port on the router, and it is a WRT160N.

View 1 Replies View Related

Linksys Wireless Router :: WRT160N - Can't Open Https://192.168.1.1

Nov 15, 2012

I need to get to my web admin page, but I cannot get into my router to do so.
 
IE tells mt that there is a certifacte error, and then gives me the option of going in anyway.
 
When I select that option, nothing happens, and the same IE warning page remains.
 
I am plugged directly into an e-net port on the router, and it is a WRT160N.

View 6 Replies View Related

Linksys Wired Router :: BEFSR41 V 3.1 - Firmware Upgraded To Wrong Version

Feb 26, 2012

I own a Linksys BEFSR41 v 3.1. I've been attempting to set up a home network with three computers; my main desktop running Windows 7 Pro x64, a netbook running the same OS and a box running Windows Home Server 2011 x64. The firmware listed for my router was initially 1.05.03.

My router has the issue with resetting its administrative password to the factory default and I've been unable to set up remote access to my LAN and home server. I decided to try updating the router's firmware, but none of the versions listed fit the one I have. The label on my router says v 3.1, but Cisco's site only has a 1.0, 2.0, 3.0, then skips to 4.1, 4.2, etc. The instructions on the site warn not to use a version for a different model, but are vague as to exactly what that refers to, as the model # and the version # aren't clearly delineated.

Anyway, I tried using the latest firmware and received the, "File Pattern," error. Although it didn't seem like anything had changed, I reset the router just to be safe, then tried the v 3.0 firmware update, thinking that the software was intended for all revisions of v3.0. This time it reported updating without a problem, so I reset the router again and went back to the admin page in my browser to check the firmware version listed. To my annoyance, the firmware is now listed as 1.05.00 - i.e. an earlier version than what was shipped on the router.

This means that not only is the issue of the password resetting not fixed, but any other fixes included in the original firmware are now wiped out as well and, needless to say, I still can't set up remote access properly.

How do I restore the firmware version?  Neither a reset nor a, "Restore to Factory Defaults," does this. How do I find an actual update for the router?  I can't find any mention of a v 3.1 on Cisco's site, let alone support information specific to this model and version.

View 1 Replies View Related

Linksys Wired Router :: BEFSR81 V2 Ports Become Inactive - Upgraded To Latest Firmware?

Jan 5, 2012

I have the Linksys BEFSR V2 router and at least once a day some or one of the ports become inactive and have to unplug the router and plug it back in to reset. I have ungraded to the latest firmware but this is still happening on a daily basis.

View 3 Replies View Related

Linksys Wireless Router :: E4200 Will Not Open Guest Login Page?

Jun 11, 2011

When Im connected to the GUEST network and open the web-browser it will not open the Linksys guest-login page. Why?(latest firmware ver.1.0.01(Build10) installed)

View 9 Replies View Related

Linksys Wireless Router :: E4200 Can’t Open Admin Page

Oct 24, 2011

I have set up a second E4200 as an AP.Even though I’m getting a signal from it I can’t open the ADMIN page. Also, it’s NOT showing up on my main 4200 "DHCP client table'.I configured it as a static IP 192.168.1.145 during setup and still cannot get in. My ping to .145 comes back “timeout”!Since I’m getting a full signal from it, it must be working so why can’t I get in and why doesn't it show up?

View 7 Replies View Related

Linksys Wireless Router :: Upgrade WRT160n To Firmware V3.0.03?

Jul 31, 2011

I had issues with my router incorrectly resolving URLs. For example, going to facebook.com would gtive me a "wiki does not exist" message. Pinging facebook.com would give me an IP that belongs to wikipedia. The answer was SUPPOSED to be upgrading to v3.0.03.I upgraded and now my router WILL NOT connect to my DSL modem. Oh, it says it's connected and shows the correct IP address for my DSL modem but the gateway is showing 0.0.0.0. Direct connection to my PC works just fine.I have cycled the power on both the router and the DSL modem several times. The DSL modem is working just fine. I have done several IP release/renew on the router. I have reset the router. To no avail. This firmware update (which completed successfully) seems to have killed my routers ability to communitcate with the internet.

View 4 Replies View Related

Linksys Wireless Router :: Where To Find Firmware For WRT160N

Mar 31, 2009

Where can I find revision 8 of the WRT160N version 2 firmware?

View 8 Replies View Related

Linksys Wireless Router :: Firmware Version For WRT160N?

Jan 25, 2013

Looking into a firmware upgrade. I have a WRT160N. The label on the back, next to Model Number, simply says WRT160N with no version number. I therefore conclude, per info on the Cisco site, that it is a V1 model, not V2 or V3. And yet the Admin web page for the router says firmware version is 3.0.02. I'm pretty confident I have never upgraded firmware on this router, which means this is how it came out of the box long ago. Latest firmware for V1 is 1.02.11; latest firmware for V3 is 3.0.03.
 
Should I upgrade to 3.0.03? Is there a way to downgrade to 1.02.11? I'm having some minor issues whch may or may not be the ruter's fault, I figure a firmware upgrade (downgrade?) will at least rule out router firmware issues.

View 5 Replies View Related

Linksys Wired Router :: BEFSR41 V4.3 / Error - Wrong Gateway Input After Firmware Upgraded

Aug 14, 2011

I have upgraded the firmware on my Linksys BEFSR41 V4.3 router. On this router i used Statis IP (so DHCP enabled). This worked fine on my network, until this upgrade. Now when i try to ad another static IP , or when i want to change something in the Routing-tab, i get this message ' Wrong Gateway Input! It should be the same subnet with WAN IP'. Strange because i haven't changed anything in the settings.I already did a complete reset on the router, still the same problem.

View 7 Replies View Related

Linksys Wireless Router :: Wrt160N Intermittent After Firmware Update

May 23, 2012

I recently updated the firmware in my WRT160N V3.Ever since, the wireless signal is intermittent.It worked all day yesterday, and now today it doesn't connect at all.I can't remember exactly the settings I used to have before updating the firmware, should have written them down.From looking at articles on this site, I have the following settings:
 
MTU   Manual  1492
 MAC Adress enabled
 Network Mode:  Mixed
Channel Width 20MHz
Channel:  11

[code].....

View 3 Replies View Related

Linksys Wireless Router :: What Is Latest Firmware Version For WRT160n

Jan 20, 2013

what is latest firmware version is for router WRT 160n (v1). The Linksys site currently states that it is Ver.1.02.11 (11/08/10). However, on the admin page for my actual router it states v1.52.0 Nov 16, 2007.  These versions #s and dates don't jive. How could I have a supposedly newer version that is older than the most recent one posted? 

View 3 Replies View Related

Linksys Wireless Router :: Wrt160n Lost Wifi Connectivity After Firmware Update

Dec 2, 2011

I updated the fimware on my WRT160N v3 and followed it up with a reset of the router.  I then restored the router settings that I had saved.  All the settings appeared to be good, but none of my wireless devices would connect.  I reneted the pass phrases (WPA2) but still nothing.  Tried to change the passphrase, still no good.  I then did a factory reset of the router from the setiings page and manually re-entered and save the settings, again nothing.  All of my devices are able to "see" the network and the correct SSID. 

View 9 Replies View Related

Linksys Wireless Router :: WRT160N V2 - Setup Cd Won't Get Past 25%

Jul 26, 2012

setup cd won't get past 25% and says not connected to the int! but yes i am .Also tryin to bridge with ATT PACE 4100n crapp!

View 2 Replies View Related

Linksys Wireless Router :: WRT160N - Internet Speeds Reduced After Installing Firmware 2.03 Build 9

Jul 28, 2012

I own the linksys wrt160n v2...It has latest firmware 2.03 build 9...After installing this firmware i have noticed the internet speeds have reduced,the router requires frequent reboots to make it stable.. 
 
i used to have firmware version 2.02 build 15...It was stable unlike the current firmware...i cant find the old firmware anywhere...how do i  revert back to old firmware?
 
All settings are currently at default. 

View 3 Replies View Related

Linksys Wireless Router :: WRT160N V3 - Cannot Connect To Setup Webpage

Apr 20, 2012

Every time I try to connect to the admin page of my router, I get "The connection to the server was reset while the page was loading."  This happens with FIrefox 11, and started when I upgraded to 8 or 9.  A machine running FF 3.6 does not exhibit this problem; I get right in.  What IE 9 says is "Internet Explorer cannot display the webpage" (after complaining about the expired certificate).
 
I ran Wireshark to see if I could learn anything, but all I could figure out was this: https handshake was OK. First TLS packet is received by router, which then immediately issues a reset and ends the connection.  I don't know why.
 
have I got a screwed up configuration (or router)?

View 5 Replies View Related

Linksys Wireless Router :: WRT160N Hangs - Restore Original Firmware In Case Update Fails?

Jun 16, 2008

I purchased a WRT160N router last Friday. After setting it up, everything seemed to work fine, but after a couple of hours, the router stopped responding to any requests. The LEDs stayed on as if nothing had happened, but the router was dropping everything coming from both the WAN and a wired LAN interface. Since than, I had to restart it 3 times during the last 3 days.The firmware is 1.53.0, which seems to be the latest firmware for the European market - even when I try to get a newer firmware, this site only offers the US version 1.02.2.Should I update the firmware to the US version 1.02.2 ? Is there any difference between the 1.53.0 and the 1.02.2 version ? Is there a way to restore the original firmware in case the update fails ? I haven't found any link to 1.53.0 version..Also, does this firmware updating affect my warranty ?

View 9 Replies View Related

Linksys Cable / DSL :: Wag 200 Is Capable For Upgraded Firmware

Mar 17, 2011

Tell me whether my router is Ipv6 capable.Firmware Version: A1.01.09 , 2008-06-13Boot Version: 0.22.02,My Isp is not using this protocol yet, but I want to be ready.

View 2 Replies View Related

Linksys Wireless Router :: WRT160N Setup As Adapter To Connect Printer To Network?

Jul 30, 2011

How do I setup a WRT160N as a wireless adapter to connect a wireless printer to my network? I do not use the wrt 160 as a router because I have an AT&T router for u-verse connection. Also, I physically cannot wire the printer to the main router (opposite corners of the house).  

View 2 Replies View Related

Linksys Wireless Router :: E2500 Cannot Connect To Setup Page

Apr 21, 2012

I can't connect to my setup page [url]... I get to the page that says..."There is a problem with this website's security certificate." Then I click the "continue to this website (not recommended). After this it will not connect 
 
Tried with IE9 and Firefox 11
 
Firefox says "The connection to the server was reset while the page was loading."
 
Internet still works. PC is connected directly to router. Tried different port on router. Tried installing CiscoConnect.E2500.1.4.11299.0,0, but it fails saying there is no router connected to PC. Like I said I am on the PC now, wired to router and have internet access via cable modem connected to router. I can see my ireless printer on the network also..

View 2 Replies View Related

Linksys Wireless Router :: EA-4500 Can't Login Into Setup Page

Oct 26, 2012

I'm trying to login to my EA4500 setup page. I have the "cloud connect" firmware and when I'm redirected to the "Linksys Smart Wi-Fi" page in my browser, I attempt to login as usual.It accepts my login name and password, and then I get a page that has a rotating graphic and it says "waiting..." It eventualy times out and takes me back to the login screen. I've tried to reboot my router and that doesn't work. I've also disconnected the internet connection from the modem, and entered the router main password, and that gives me the same response as if I tried to connect via the cloud.

View 9 Replies View Related

Linksys Wireless Router :: Cannot Access WRT54G Setup Page

Jan 19, 2013

I have a WRT54G router that I have not used for many years, but now I need to use it again. I have connected it between my modem and PC, and I am able to get an internet connection on the PC, but I am unable to connect to the router's configuration page. I have tried resetting the router numerous times (holding the reset button 5 seconds, 10 seconds, even longer) to reset the IP address to the default 192.168.1.1 address, but still cannot access the page. The power LED is on and the WLAN and Internet LEDs are on, and the LED for the port my PC is connected to is on. The hardware version of the router is v3. I tried downloading the latest firmware, but without being anble to communicate with the router at the IP address I cannot update the firmware. How can I go about connectiong to the router's setup page? When using ipconfig, the Default Gateway appears to still point to my ISP's IP address instead of the router's.

View 9 Replies View Related

Linksys Wireless Router :: Cannot Access E1200 Setup Page

Nov 29, 2012

I'm able to connect to the internet through my E1200 router but I cannot access the router set up page. 192.168.1.1 doesn't work... I can connect to it just fine with my laptop however... so I changed it to 192.168.254.1 as per some internet instructions. Still can't connect via my desktop... Tried ipconfig /flushdns to no avail. Cleared the internet cache Upgraded the firmware (via the laptop) rebooted the computer rebooted the router... reset the router... After rebooting the router I can type in the username and password to access the router, but it never connects....

View 6 Replies View Related

Linksys Wireless Router :: Can't Access Setup Page WRT54GS

Sep 9, 2012

I need to set up a password for my wireless network, but every time I try to access the setup page, the router stops responding.  I've gotten as far as it asking for username and password, where I enter admin as the password....and then nothing.  The connection times out.  I really need to protect my network.

View 1 Replies View Related

Linksys Wireless Router :: E4200V2 Can't Get To Advanced Setup Page

Apr 3, 2012

I just installed new E4200V2.  After completing software install, everything appears to be working fine, except that I can't get to the advanced setup page, either through Cisco connect software or from the web page utility.  Either way, the advanced settings web page never finishes loading.  I am using the correct login information for the web page utility.  It accepts the username "admin" and password, but never loads.  Browser just sits there.  Browser status bar says "waiting for http://192.168.1.1. 

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved