Linksys Wireless Router :: WRT54G Page Has Reverted To Default

Feb 24, 2012

I have a Linxsys WRT54G.  Once every week or two, it seems to "forget" its name, and revert to the default name.  When I try to access it with my laptop or phone, "Multivac" is gone, and "Linxsys_XXXXXXX" (where XXXX are random numbers and letters) has taken its place.  When I go to the setup at 192.168.1.1, the "Router Name" on the first "Basic Setup" page is still "Multivac," but the "Network Name" on the second "Wireless" page has reverted to the default.  If I change it back to Multivac, everything is fine for a week or three until it "forgets" again.

View 1 Replies


ADVERTISEMENT

Linksys Wireless Router :: Cannot Access WRT54G Setup Page

Jan 19, 2013

I have a WRT54G router that I have not used for many years, but now I need to use it again. I have connected it between my modem and PC, and I am able to get an internet connection on the PC, but I am unable to connect to the router's configuration page. I have tried resetting the router numerous times (holding the reset button 5 seconds, 10 seconds, even longer) to reset the IP address to the default 192.168.1.1 address, but still cannot access the page. The power LED is on and the WLAN and Internet LEDs are on, and the LED for the port my PC is connected to is on. The hardware version of the router is v3. I tried downloading the latest firmware, but without being anble to communicate with the router at the IP address I cannot update the firmware. How can I go about connectiong to the router's setup page? When using ipconfig, the Default Gateway appears to still point to my ISP's IP address instead of the router's.

View 9 Replies View Related

Linksys Wireless Router :: WRT54G Administrator Page Is Broken?

Sep 27, 2012

I recently "uninstalled" DD-WRT from my router and tried to install the actual firmware for the router, so I went to this page [URL] WRT54G and select version 5. My router is really version 5.1 but I read on this forum that this router works with version 5 so I downloaded it and installed it.
 
However, this is how my admin page looks like,
 
And I can't do anything at all. Is there a fix for this? Is there an actual version 5.1 firmware? Or must I switch to a different, proper router?

View 8 Replies View Related

Linksys Wireless Router :: WRT54G - How To Access Setup Page

Apr 27, 2012

When I had DSL, my WRT54G was my DHCP master for my home network.  When I got AT&T U-Verse, their "gateway" became the DHCP master and also the wireless access point.  But the signal was not strong enough where I wanted to use it, so I hooked up the WRT54G again.  I discovered that if I connected the U-Verse gateway to the "Internet" port on the WRT54G Linksys, then my home network was split in two, which I did not want.  The WRT54G access point is physically somewhat distant from my wired computer, so I wanted to keep the U-Verse gateway as the DHCP master. (The U-Verse gateway is a router with four "computer" ports but no "Internet" port.)
 
I followed instructions on the Linksys web site, and using my wi-fi connected computer I re-programmed the WRT54G to be "Disabled" as a DHCP server.  Then I powered down and physically connected the U-Verse gateway to a "Computer" port on the WRT54G.  This solved my problem:  my distant wi-fi computer now has a good signal, and both computers "see" each other.
 
However, now I seem to have lost access to the WRT54G setup "web page."  Is it possible to access the innards of the WRT54G when its DHCP service is disabled?  Or would I have to reset the device to factory configuration and start all over if I wanted to make any tweaks?

View 3 Replies View Related

Linksys Wireless Router :: WRT54G - Put ASPX Page When Start Connection?

Sep 9, 2011

Is there a way to put the .EXE program in the start connection in Wireless Router WRT54G ?
 
or a .ASPX page when start the connection ? I want to do it:
 
I want to control the time that the users used the internet in the hotel. The users had the login and the password which one. And I want stop the connection when the user get the time.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G - Lost Username And Password For Admin Page

Apr 30, 2007

I seem to have lost my username and password for the admin page for my WRT54G router.Is there a way to retrieve or reset the login?

View 9 Replies View Related

Linksys Wireless Router :: WRT54G V8 / Unable To Navigate The Basic Setup Page

Jan 14, 2008

I have been trying to change my password and all the settings on my WRT54G V8 router today because I forgot the password, and I can't seem to navigate the Basic Setup page. I can log in (most of the time) after resetting the router, but whenever I try to click on a different tab (like "Wireless", or "Security") it comes up with the page saying "This Page Cannot Be Displayed."  I'd like to be able to put a password on it (which I have successfully done before on this router) because I live in a college dorm and would like to keep my internet from being bogged down by other people using it. 

View 9 Replies View Related

Linksys Wireless Router :: WRT54G Resetting To Factory Default By Itself?

Aug 11, 2008

I have a WRT54G router Ver. 5 with firmware v. 1.02.5.  This is the second time this has happened to me but the router reset itself to the factory defaults. I lost all my configurations.   I'm saving the configuration this time but it will be annoying to keep having to reconfigure the router.

View 9 Replies View Related

Linksys Wireless Router :: E3200 - Block Keywords And Customize Default Page Given When Access Restricted?

Aug 5, 2012

Is there a way to block keywords and also customize the default page given when access is restricted?

View 1 Replies View Related

Linksys Wireless Router :: WRT54G Version 2 Weird Default Gateway

Nov 21, 2012

We were hit by hurricane Sandy a couple weeks ago and lost power for a week and a half. Now that our cable has been restored I noticed that the wireless internet wasn't working. The wired internet works fine to this computer but no Wi-fi.I think the problem is the routers default gateway. It's supposed to be 192.168.1.1 but right now it's 24.191.112.1 .So far I have tried:

-Powercycling everything
-ipconfig/ flush DNS
-ipconfig/ release and ipconfig/renew
-Checking all the wires are pugged in fine (They are).

View 1 Replies View Related

Linksys Wireless Router :: WRT54G - Default Username And Password For Port Forwarding?

Jan 24, 2013

I have a WRT54G Linksys router and I am wondering what is the default username and password for port forwarding?

View 1 Replies View Related

Linksys Wrt54g - How To Access Router Set Up Page

Oct 8, 2011

running linksys wrt54g wireless router to two towers and 1 laptop----had short power outage after which i lost connection to router only on one tower---other tower and laptop were unaffected----had green indicator lights for positions 1 and 2 hard wire connected towers before outage---now only position 2----looking for reasons why I lost number 1 and thus connectivity to the router----have tried powering down router etc---but have not reset it---looking for more info first

View 1 Replies View Related

Linksys WRT54G V3.1 - Cannot Access Set Up Page In Router

Sep 18, 2011

My wifi router, Linksys WRT54G v3.1 has been working fine till now. Suddenly my laptop stopped receiving wifi signal. I am unable to access the set up page via 192.168.1.1 either from my laptop or from my desktop that is connected to the modem via the router. I reset the router as well but no luck.

View 5 Replies View Related

Linksys WRT54G - Garbled Router Web Administration Page

Mar 11, 2013

Sometimes, when I access my router's (Linksys WRT54G) web administration page, it comes out garbled; i.e. missing text, icons, links, form controls, etc.

Gets fixed after powering the router off then on again.

View 1 Replies View Related

Access Linksys WRT54G Config Page?

Dec 24, 2012

I just got a new Sharp Aquos Television and I wanted to try to find the SSID so that I could pick up a connection with my TV. When I went to command prompt and typed ipconfig to get the default gateway, the gateway ip took me to what appears to be my modem's config page and not the Linksys. how I can get to my WRT54G config page.

View 2 Replies View Related

Routers / Switches :: Cannot Connect To Router's Default Admin Page?

Dec 25, 2012

Motorola wr850gp wireless router. The default ip is 192.168.10.1. I attempted to use it as a wireless access point and now it is not working at all. I tried connecting the router LAN port to the computer and 192.168.10.1 pulls up nothing.I tried connecting the modem to the WAN port and the LAN port of the router to the PC, but then I have no internet access at all. I tried resetting the router, still nothingAll lights on the router are green. I don't know what the heck is going on?

View 3 Replies View Related

WRT54G Router - Access Points Use Default Antennas

Jan 22, 2012

I am pretty clueless with anything beyond creating a simple home wireless network. But I work at a 10 room inn which is surrounded by a few properties that are also part of the inn. We need to adequately cover a diameter of about 400ft in all directions from the inn with wireless internet. Even at 400 ft the signal should be reliable and able to Skype and stream videos. The path from the Inn to each of the surrounding properties is clear. For those with experience setting up a wireless network with 400ft diameter, what equipment would you recommend?

Our network now consists of several WRT54G routers. The access points use the default antennas and we have a couple directional antennas to reach a couple of the nearby houses. We need the signal to reach another house or two now. Rather than installing more directional antennas, the owner of the inn wants to wants to just purchase new equipment for the Inn to easily reach all of the surrounding houses which house innkeepers or guests.

View 6 Replies View Related

Default Gateway Not Available - Limited Access / Cannot Find Page?

Oct 5, 2011

I just switched internet providers and i have wireless, since then, my boyfriends laptop is having problems staying connected to the internet. the desktop and my laptop stay connected his doesnt. it will say connected or limited access but i cant get a webpage or when i do its internet explorer cannot find page.System Info Utility version 1.0.0.1[CODE]

View 14 Replies View Related

Linksys Wireless Router :: Map Page On Wrt120n?

Apr 2, 2013

why are some of the lines solid & others dotted on the map page?

View 4 Replies View Related

Cisco VPN ::ASA 5550 / Default Connection Profile On WEBVPN Login Page

Jul 5, 2011

I have a pair of ASA 5550s running Anyconnect Essentials, with multiple connection profiles configured. I would like the login page to the portal to default to our main corporate profile (so the users get NAM and all the policy goodness), but presently it is defaulting to the last profile I created.  Is there any way to modify the default connection profile in the drop down list so it always defaults to my preferred profile? It seems like I saw this sometime in the past. 

View 2 Replies View Related

Linksys Wireless Router :: Set Home Page On WRT54GL?

Dec 17, 2011

I am using a WRT54GL for the free wifi service at my business.  Is there any way to set it so that when someone accesses the internet they are directed to my business home page first?

View 1 Replies View Related

Linksys Wireless Router :: E3000 - Can't Connect To Router Settings Page

Dec 25, 2012

When I try to go to192.168.1.1 it says connection interrupted.  If i use the Cisco Connect it tells me i am not connected to the internet.  My pc is connected via ethernet cable. My son can pull it up on is laptop and is connect the our Linksys E3000 wirelessly.  I can go online, I just cant get to the router.  

View 9 Replies View Related

Linksys Wireless Router :: E1200 - How To Access Router Admin Page

Apr 1, 2012

I want access the my E1200 website in order to implement new username and password to secure the network.

View 1 Replies View Related

Linksys Wireless Router :: E4500 Don't See Version On Download Page

Nov 1, 2012

I see I have 2.1.39.144146 but I don't see that version on the download page?

View 3 Replies View Related

Linksys Wireless Router :: E2500 Cannot Connect To Setup Page

Apr 21, 2012

I can't connect to my setup page [url]... I get to the page that says..."There is a problem with this website's security certificate." Then I click the "continue to this website (not recommended). After this it will not connect 
 
Tried with IE9 and Firefox 11
 
Firefox says "The connection to the server was reset while the page was loading."
 
Internet still works. PC is connected directly to router. Tried different port on router. Tried installing CiscoConnect.E2500.1.4.11299.0,0, but it fails saying there is no router connected to PC. Like I said I am on the PC now, wired to router and have internet access via cable modem connected to router. I can see my ireless printer on the network also..

View 2 Replies View Related

Linksys Wireless Router :: E4200 / 192.168.0.1 Modem Page Unreachable

Feb 1, 2012

Once in a while, I lose Internet connection and at the same time cannot reach my Siemens Speetstream 4100b DSL modem's setup page 192.168.0.1 ; it happened again this morning (from both wired and wirelessy connected computers). When I go to the router's setup page 192.168.1.1 , it would usually in that situation show that the router has not acquired the Internet IP Address; I power-recycle (a few times) both modem and router and eventually the router reports that it has acquired the Internet IP Address, but there is still no Internet, and the DSL modem's setup page 192.168.0.1 is unreacheable.The situation usually self-resolves only in an hour or so after the time the router has acquired the Internet IP Address: Internet starts working, and the DSL modem's setup page 192.168.0.1 becomes reacheable. 

View 2 Replies View Related

Linksys Wireless Router :: Way To Access Set Up Page For Secondary WRT300N

Aug 13, 2012

Since the secondary router WRT300N uses the same default IP 192.168.1.1 as the primary installed router EA4500, any attempt to log onto the set up page results in diversion to the Cisco Connect Cloud for the primary router.
 
Is there a way to access the set up page for the  secondary WRT300N, bypassing the main router intervention via the Cloud  software?

View 3 Replies View Related

Linksys Wireless Router :: Cannot Connect To Admin Page At All On E3200

Feb 23, 2012

I don't have to completely reset my router as I have a ton of configs on it.  Anyway, recently for some reason, I lost all access to my admin page.  Cisco Connect also cannot find the router.  Funny thing is that all of my wireless profiles work just fine.  Meaning all of the computers in my home connect to the internet just fine using the router.  Both the guest access and WPA connected machines.[url]...

View 1 Replies View Related

Linksys Wireless Router :: EA-4500 Can't Login Into Setup Page

Oct 26, 2012

I'm trying to login to my EA4500 setup page. I have the "cloud connect" firmware and when I'm redirected to the "Linksys Smart Wi-Fi" page in my browser, I attempt to login as usual.It accepts my login name and password, and then I get a page that has a rotating graphic and it says "waiting..." It eventualy times out and takes me back to the login screen. I've tried to reboot my router and that doesn't work. I've also disconnected the internet connection from the modem, and entered the router main password, and that gives me the same response as if I tried to connect via the cloud.

View 9 Replies View Related

Linksys Wireless Router :: Can't Access WRT160n Setup Page

Oct 16, 2012

I have updated the WRT160n firmware and, since then, I couldn't access the setup page anymore. I could still use the router as a switch, but couldn't access the setup page and configure it as a router.

View 5 Replies View Related

Linksys Wireless Router :: E2500 - Page Not Fully Loading

Mar 24, 2013

It's' my first router (E 2500) one desk top and two laptop and also a Ipad connected, every thing look fine exept for the Ipad.Lots of page not fully loading, I have to reload couples of time to get it full load. and lots of Youtube video said not presently availale but work fine with laptop or desktop.Did not change any seting on the router, I just plug it and used it

View 9 Replies View Related

Linksys Wireless Router :: Cannot Access E1200 Setup Page

Nov 29, 2012

I'm able to connect to the internet through my E1200 router but I cannot access the router set up page. 192.168.1.1 doesn't work... I can connect to it just fine with my laptop however... so I changed it to 192.168.254.1 as per some internet instructions. Still can't connect via my desktop... Tried ipconfig /flushdns to no avail. Cleared the internet cache Upgraded the firmware (via the laptop) rebooted the computer rebooted the router... reset the router... After rebooting the router I can type in the username and password to access the router, but it never connects....

View 6 Replies View Related

Linksys Wireless Router :: Can't Access Setup Page WRT54GS

Sep 9, 2012

I need to set up a password for my wireless network, but every time I try to access the setup page, the router stops responding.  I've gotten as far as it asking for username and password, where I enter admin as the password....and then nothing.  The connection times out.  I really need to protect my network.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved