Linksys Wireless Router :: WRT610N V2 Access Restrictions Menu Is Missing In Admin Gui
Nov 18, 2011
I 'd like to use the access restrictions capabilities of the WRT610N v2. Unfortunely the "Access Restrictions" menu is missing in the admin GUI; I 've got all the others : "Set -up", "Wireless", "Security", Storage, Applications and Gaming, Administration and Status. I've checked the Firmware already and i'm using the very last one available on the cisco web site. I also noticed that I do not have the "Linksys by Cisco" text on the upper left corner as one can read on user guide but just "Cisco".
I want to set up access restrictions to one MAC address (my kid's machine) basing on week days. From Su to Th allow less access time while during Fr-Sa afternoons access time should be longer. The question is how to program it in router. I know I can set rules with "allow" and "disable" keyword, but I don't know rules preference. When I set (Su-Th 6-21) allowed access time then router automatically denies defined machine internet access outside this time range. The problem is in the power of thus calculated denying time. I want to allow more access time in weekend, so I hoped if I can simply add "Fr-Sa 6-22:30 allowed access time" rule. I hoped that router will regard explicitly set time over inexplicitly set time but it appears it is not so. What are their preferences/priorieties, iis it possible to stack more rules affecting one MAC address or it is so simple that the first rule "rulez"? Is it possible to set more than one time rule affecting the one machine?
I decided to limit some Internet time for the kids going off this router (which has been working great since set up) but my Access Restrictions tab is missing. I have an identical router at my work place, same version/firmware, same settings, but the one at work does have the tab.
I am trying to log into my WRT610N version 2.0 Router admin page 192.168.1.1 using the secure HTTPS://192.168.1.1 protocol I have the router local management setting to allow both http and https access login:192.168.1.1/Management.asp I am using Microsoft IE version 10 and Firefox version 19.02 and latest Chrome browsers and none of them will work using the HTTPS protocol.This used to work in the past using older versions of the browsers though I would see a certicificate error warning.I have 2.00.01 build 15 firmware installed and I already tried reseting the router. Perhaps the router needs new firmware update to handle this with the latest browsers?
What happen to my router linksys e1200, after i update the firmware to the latest version "Access Restrictions" is change to "Access Policy". how can i revert it back to "Access Restrictions" do i need to downgrade the firmware?
I'm having problems with the access restrictions feature on the WRT600N. I do have the latest firmware upgrade, which was released in 2008 I believe. Anyways whenever I totally block a PC from the internet either by MAC or by IP, it affects the internet on the rest of the house. Logins to sites do not work right. Logouts from do not work right. Different features of different sites will not work properly. There also will be a lag sometimes when entering the url for a new site. But as soon as I turn the access restriction off, everything goes immediately back to how it should be working.
I have access restrictions set up for certain wireless devices in my home that the kids use to kick them off at 11 pm and keep them off all night. where I am running into a problem is I want to block these same devices from downloading anything without my permission my son downloads everything he sees, Comcat has already threatened to kick us off their service if we go over 250 gb bandwidth use in a month again. so I want to configure something in the router that will block all downloads for specific wireless devices. with the access restrictions I have set up I used the mac address not just the ip so they have no way around it I constantly monitor what is connected. I am using the stock firmware as well
I just purchased an E-3000 and when I log into the user interface it seems changing pages and saving settings takes forever. I click on a section in the router menu and it takes what seems like 30 seconds for the page to change or accept the new settings. It's not my browser it's definitely a Linksys Router issue. I updated to the latest firmware and latest Cisco Connect software as well. Is this slow user interface a normal thing with these routers?
I am trying to get a cell phone to have access to my LAN from 3am to 7am. I gave the policy a name, allowed access, checked everyday and the time 3a to 7a. Under edit list of PCs, I entered the MAC address of the phone, and I have also entered the MAC address of the phone on the wireless>edit mac filter list, though didn't know if I should.
I keep trying to set access restrictions for my wrt54g router for time. There is no 12 for time so I'm selecting 11:55 pm to 6am but I keep getting an error message of, "end time must be bigger then begin time." I get this no matter if I select 9pm, 10pm, etc.
I am using a WRT150N with firmware v1.00.5. I have a Linux setup with Squid connected to the network with the gateway 192.168.23.254. The WRT150N has a gateway of 192.168.23.1. The WRT150N is also connected to an Apple Base Station which serves as the Access Point for WiFi users.Squid limits access for IP addresses listed under the .254 gateway. But once I change my gateway to 23.1, everything is accessible. I want to block sites as well on the WRT150N. But every time I try to put a new Access Restriction, it doesn't work.
I had a E1200, I read the articles from the support about the routers, I think the "access Restrictions" has more flexible to setup on for the parental control, after chated to cisco support person online, I was told that the E1200 v2 has this "access restrictions" function, and I wan convinced to purchase from them. I did. I got the E1200 v2 recently, however, after I installed the CD and found there is no "access restrictions" tab, instead the "access policy" is still there. by the way the firmware is 2.0.02 now. How to get the "access restrictions" from setup? I've chatted with cisco support person twice again, but nobody can fix the problem, one suggested to restart and reinstall the CD. I uninstalled the software, restarted the computer and reinstalled the CD. same problem, no tab of "access restrictions".
Recently switched from WEP to WPA2 on the router and let it run a few days. Everything was copacetic.
Then decided to implement the following access restrictions:
1 - Target MAC based, internet blocked from 9-11:55 PM (why won't it let you block from 9PM-7AM ;-( ), blocks son #1's laptop, Kindle
2 - Target MAC based, internet blocked from 10-11:55 PM, blocks son #2's Kindle
3 - Targets IP Address range based (192.168.1.0 - 192.168.1.254), across all devices blocks several porn sites all the time
I can get on a play games online but when we start watching video with all 3 restrictions enabled, it will eventually disconnect (can take 1-5 minutes before it happens). Rebooting XBox usually reset connection, but it would happen again eventually. After disabling all restrictions, disconnects completely stopped.
Is it not possible to have Access Restrictions in place on a WR54G and still stream video?
I have been looking into this router, I would like to know if I can enable Parental controls or access restrictions to block a MAC or IP address; from 03:00 AM - 06:00 AM ?Instead of Midnight to 6:00 am.My E4200 works just fine, Just would like to know if the EA6500 Can do that ?
I am uable to access my files on the USB Storage Device connected to WRT610. Its configured properly. I can see the drive on my network. When I double click it asks for password which I enter and it takes me to the shared folder. But when I click it it says Not Accessible....You donot have the persmission. FTP works fine.I have noticed that on the disk page in the Shared Folder Area when you click on the Summary, the box with Groups With Access is Empty. Whereas on the FTP area in the same summary it clearly mentions the admin group.I have tried every thing including factory reset, hard reset, using new group, new user name etc..The technician from Linsys even spent an hour on my computer and ultimately he gave up and gave me number to contact technical support.
I have the following network configuration. Linksys E4200 is a main router which connects directly to internet. I have also a couple of WET610 bridges. One of them sends internet through WAP610 (linksys access point - works fine). Another one is still free, so I would like to share internet from the second WET610 through my WRT610n router. I tried to use the same setting as people recommended for direct cable connection of two routers (WRT610n WAN -> main router's LAN; DHCP and NAT on WRT610 turned off, WRT610's IP differs from the main router's IP), but it doesn't work in my case (WRT610n WAN -> WET610 -> wireless -> E4200). Unfortunately WRT610 doesn't see DHCP (so no one of clients receives proper IP, I can't reach my network if I connect to WRT610, I can't reach WRT610 from my network).
The Internet Access Policy feature of my WRT610N router doesn't appear to work, at all, zip, nothing, nada. I have setup the feature todeny access to one of my laptops for everyday 24 hours a day, but it can still use the net...
My main pc is running Windows 7. It is also running MS Windows firewall and anti-virus. It connects fine to the internet via an ethernet connection to the WRT610N.
I am trying to access the internet wirelessly from another pc running Windows XP. The wireless pc indicates it is connected to the network with excellent signal strength. It will not connect to the internet. I can successfully ping the router but it is unsuccessful when pinging an internet address.
An additional wireless pc (WinXP) and my phone (Android) also show connected to the network but will not connect to the internet.
These wireless computers used to be able to access the internet before we moved house. They only thing I think that has changed is the addition of Windows firewall and anti-virus. It may however be something else.
I'm unable to access the web setup screen from 4 different windows machines running IE 9 or Firefox (various combinations of wireless, wired, etc.). When I get to the certificate error and hit the "yes, i understand, continue", it comes back with a 'can't be reached' page and looking into the details says the 'connection was dropped'. However If I connect from a MacBook / safari, I'm able to reach the page fine (and admin the router).
Using a wrt610n.I am connected to the router, the ip address hasn't changed, the password hasn't changed.I can use the router & connect to the internet.I have the router set to require HTTPS, but switching it to allow HTTP doesn't work. Both Wired & Wireless Win 7 / IE9 machines can't connect.Tried setting the router ip address to 'trusted' zone in IE. Tried setting the router ip address to the 'compatibility' mode in IE. Tried using latest version of Firefox with the same results.
We currently have an issue with our main ISE. When logged in using the admin account (member of superadmin group) we no longer see the Profiling button/menu and also missing oter options in the GUI. On another standalone ISE we do see al those options?
Both are running on the same software version 188.8.131.528.We are using ISE 3395-K9 appliances
Have an Actiontec GT704 feeding DSL into a BEFSR41 which is connected to a WRT610N. Can access internet, modem and wired router from desktop. Can access wireless router from laptop. Cannot access internet from laptop or wireless router from desktop. Changed ip address for wireless router to 192.168.2.1 so no conflict with modem or wired router.
I just moved in to a new place and have connected my Wireless router (WRT610N) to my switch located in the smart panel in the basement (SE2500). Plugging my ultrabook in to the wall confirms that the signal from the switch in the basement is being sent up, however if I plug my wireless router in to the jack and connect to the wireless router I have no internet access.
I'm very dissatisfied with the range and signal strength of my new WRT610N dual band router compared to the WAP54G Access Point I used before.Can I configure the Access Point as a repeater for the 2.4 GHz band on the WRT610N if I use the WRT610N as a Wireless G router rather than wireless N?
I cannot access the WRT610n setup/management pages wirelessly from my Macbook using safari. I can access the router via wireless from iPhone and PC and I can access it from the Macbook via ethernet cable.
When I try to access the router from the Macbook I just get "Contacting..." in the Safari status line and eventually it times out.
I can access the internet using Safari via WRT610n wireless. The only page I can't access is the router's management page.