when I couldnt turn on the wifi from the switch. It remained orange(which is its off state) and so I went to the device manager and the wifi adapter was shown there but with an exclamation mark. Showing the error "the device cannot be started(code 10)". So I uninstalled and rebooted, only to get the same error when it got reinstalled.
So I have an HP Pavilion dv9000 laptop with window 8 installed and when I try to connect to the internet I keep getting an error that says the "Ethernet" Adapter is not working properly. I used to be able to go on the internet and then my dad had my computer for a while and now it's not working.
i am trying to connect wifi .i have two wifi hotspots. it just connects with one hotspot and if i try to to switch to other one it just shows windows was unable to connect. and it does not switch back to the previous connection. even it does no go to communicate with access point. directly shows widows was unable to connect.
I turned on the monitor (I had left the system running) and it said that it had recovered from an unexpected shut down. It didn't automatically connect to the wifi, so I opened the connections window to connect to a network and it said "Windows cannot find any networks." I refreshed several times and nothing happened. I clicked the option underneath "Diagnose why windows can't find any networks," and it came back with "This computer does not have a wireless adapter installed and configured." I then opened up the device manager, and under network Adapters, the only thing is "Intel(R) 82566DC-2 Gigabit Network Connection." I checked it out and it says it's working properly, and I believe that this adapter is for when you actually connect a cable directly to the PC.
months ago, i installed a USB card so that my dvd burner could run at 2.0 or 3.0. it has worked fine. every now and then the card becomes unlodged from inside the computer, and i have to push it back into the slot.Tonight, while the computer was on, i was putting it back in, and it popped all the way out, my computer shut down and when i restarted it, i got the error message "windows did not find properly installed network adapter/ if you have network adapter update/re-install drivers"Only problem i have is when i go to device manager, i see NO network adapter?
I purchased a new built system, worked great 5 days, major trojan forced a reformat of drive. Now Win 7 64 Device Manager is empty- no network adapter found - I get the notice that "there are no properly installed network adapters". I use the on-board network adapter on the mobo, no plug in network card, hard wired to DSL -- like I said, it worked fine for a few days now it's GONE after reformat.
I'm working on an M5030 that has a red X on the wireless and will not find any networks.
- The ethernet connection WORKS
- The fn+f2 wireless switch combo seems to do nothing
- I've updated the bios
- I've uninstalled and installed the latest driver
- I've installed external USB wireless adapter but it has same issue
- I've scanned for malware, all clean.
When I go to network adapters it has signal bars on the wireless adapter but when I right click -> connect disconnect -> nothing shows as available. If I diagnose, it just says there may be a problem with the wireless adapter. I've tried DISABLING ZoneAlarm firewall to no avail also.
My laptop keeps saying "Windows did not detect a properly installed network adapter.If you have a network adapter, you will need to re-insatll the driver". I've found the right one and it still want install. Says it's the wrong one but i'm pretty sure it's the right one. I just did a fresh install where i put windows 7 extreme on a laptop and i can't seem to ge the right drivers i guess. I don't know if it's the wrong driver or a bad NIC Card.
i had an extra network under my wireless networks that was just called "network" which was not connected to anything, but since i had this, on the bottom right of my screen where it normally showed the bars for the wireless connection, it had the bars grey with a red X on them, but my connection worked fine still.I am using windows 7 64x bit. I always use a wireless connection on my laptop.
I have 2 computers, One running Vista 32, Desktop.Another, Laptop, Win 7 64bit.Both computers have given Error 651 when using PPPoE wired connections, usually at the peak of the day.My ISP says that Error 651 is the problem, while I am starting to think its the amount of bandwidth their giving my neighborhood/home.Also, can that dosen't work,how to fix the overall problem of my Internet shutting off at peak hours?
I have a Netgear CVD31T modem delivered by my internet provider. I can't change any settings on the modem. My connection speed is 30 gb up and 5 GB down.Until now I used a Linksys WRT54GV ver. 2 router to share my connection between my computers and NAS server and it worked ok. In speed tests I normally get approx 25 - 28 GB speed. To optain more speed on my LAN I want to buy a GB router. And here started my problems. First I tried a D-link DIR655, then a Netgear WNDR3700 and latest a Linksys E3000. I all 3 occations my WAN speed droped drasticaly down to between 3 - 5 GB speed, at under a ping test I have a loss of between 10 - 30 % and time on approx 50 ms.If I connect my PC directly to the modem or re-connect my old router it works perfect. I have tried to replace cables etc. etc.
Last night on the xbox 360 i was suddenly experiencing alot of lag on other peoples voices. i took no notice of it and the next day i went on my laptop and alot of websites wouldn't load properly.i can go on google,obviously this and my hotmail(after having to wait a long time for the hotmail to load), but others such as ebay will not load. I cannot even access my router settings by typing in my ip address, instead i get a message saying the page cannot be found. also i was disconnected from xbox live with the internet to xbox live part not working. Obviously the first thing i done was turn the router off and back on but it hasn't made any difference.
OS Version: Microsoft Windows Vista Home Premium , Service Pack 2, 64 bit Processor: Pentium(R) Dual-Core CPU T4200 @ 2.00GHz, Intel64 Family 6 Model 23 Stepping 10 Processor Count: 2 RAM: 4055 Mb Graphics Card: Mobile Intel(R) 4 Series Express Chipset Family, 1804 Mb Hard Drives: C: Total - 290204 MB, Free - 141170 MB; E: Total - 14999 MB, Free - 5644 MB; Motherboard: Dell Inc., 0G848F, , .5MDJWJ1.CN7016697U05OT. Antivirus: AVG Anti-Virus Free Edition 2011, Updated and Enabled
I bought a TP-Link TL-WR841N which i have managed to setup up properly, i am able to connect to the wireless and get internet access. However the minute i walk out of the room or a few meters away i am disconnected and i can't re-connect, i get the "windows cannot connect to TP-LINK" message. The signal strength in on excellent and i know it works because when i stand near it, it works perfect.I phoned TP-LINK technical support who were pretty useless and couldn't fix the problem.
ive been having some issues with my internet, i had an attack on my pc recently by some american orginization, ive reinstalled new windows on my pc, reset my modem, and nothign seems to work, i have too many tunnel adapters in cmd ip config i think, bell canada hooked up my internet lines and they actually joined two or more wires together and strung them up on the neighbours fence and mine and even wrapped it around a tree branch, god knows why they would even do that, maybe they think when the tree grows it will cost me money to fix it and theyll earn from thier mistakes instead of learn from them... anyway this is my ipconfig test results as explained in previous post from someone.Windows IP Configuration[CODE]
Some Trouble With My Wired Internet Connection,basically it worked somedays other days it cut off and didnt work for a few days,i phoned virgin media who sent me a new modem.Everything is set up and activated and it worked for about a day,now it has stopped working even though the computer says im connected,everytime i try internet explorer or firefox i get a white screen and every webpage i try fails,but if i bring up utorrent i can see that my internet is connected because it begins to download the ebooks
I recently replaced a Linksys wireless router with a Netgear wireless router(provided by Comcast) to the modem in my house. I used my HP Pavilion as the computer to run the setup disk and the wireless wizard to link the new router to the modem. I unplugged my HP from the router and proceeded to setup my computer on the wireless network.
When I check the strength sometimes it indicates it's good if I'm practically sitting on top of the router, this seems to eventually degrade to low until finally the connection drops.Repairing' with XP repair facility doesn't work. I can forget about getting a connection if I move further away from the router. At the moment I'm relying on using an ethernet cable snaking across the dining room, which isn't really practical with a toddler and a dog racing around. Recently a friend put a bigger HD in and before this it was working fine, so I suspect that it may be due to this. I think it's due to the wirless card in the laptop, as I have a number of other devices in the house which all work fine.
I not familiar with the ASA 5510 product. I having trouble since last 24 hours and still cant find out the root cause yet. Here is my scenario, my network should be
WAN --- ASA5510 (FW) --- SERVER (192.168.1.0/24)
Now I face the problem, all the NAT static 1-to-1 is working OK. All my public IP can be ping from outside internet. But the problem happen when I try to telnet to port 80 on each server. I had try telnet from my PC to public IP 124.xxx.179 80, it's work fine, but failed on 124.xxx.180 80, then on 124.xxx.181 80, its work fine.
Then I do try on my colleague PC, in same network as mine, I face another case where the public IP 124.xxx.179 80 cannot be telnet, but it's ok for 124.xxx.180, then failed on 124.xxx.181 80.
FYI.. all our PC can ping to the Public IP and no packet lose.
The scenario is very weird, I cant find any other solution as had review my configuration few times.
check does my configuration is working perfectly or not.
ASA Version 8.2(5) ! hostname fw-asa enable password xxx encrypted
The Network icon in the notification area in the bottom right hand corner of my screen will almost always look like this:Quite frequently, though, I will get an exclamation mark inside a triangle with a message instead saying No internet access (I don't have a screenshot). If I give it a few seconds, usually never more than a minute (30 seconds on average it seems), it corrects itself and gives me back internet access.
I recently made an old router into a repeater by using DD-WRT. It seems to be working fine if I use LAN, but I cannot get WLAN to function properly. When I go to add a virtual interface and all the proper info, I all of a sudden cannot connect to the Internet. More specifically it seems to not assign me an IP address.
I checked what she needed, updated her drivers for Ethernet and Wireless, and the Device Manager is stating that they are both working fine. (no ! or ? on them)When I plug in an ethernet cable it works fine. It gets connection pretty well through my BT Infinity modem.However the wireless will not pick up any connections at all. I attempted troubleshooting, and all it says, "Your network adapter is experiencing problems" etc.I thought that I may need to turn on Wireless Association on the modem, but that didn't work. My dads laptop is also a Windows 7 Laptop and that works fine and will bring up all connections in the area, including mine.
So I googled around, and I found that I may need to turn on a wireless switch. After looking around the laptop, I noticed two things. 1) There is no wireless switch, and 2) There is an orange light above the WIFI symbol.So I googled around a bit more, and found it might be turned off in the FN+f8 Flash card feature. At first I couldn't actually bring this up, so I reinstalled the flash card, and it began to work. It claims the wireless connection is "On".I am not sure what to do next. I have checked the services to make sure WLAN Autoconfig is on Automatic, and Started, and it is. I also tried disabling, then enabling both ethernet, and wireless connections, which did nothing.
I've been having some problems with my Ethernet connection lately.I unplugged my laptop from the Ethernet connection I had at my old place.At two different locales, I have tried to use an Ethernet connection in order to get better speed (the wireless at the first locale was non-existent and at the second it is extremely slow in my room). I have done so with two separate cables that I have tested on others' computers and found that they are perfectly fine. That, of course, leads me to believe that it is my computer and is either a hardware or software problem (here's hoping it's the latter).Anyway, my laptop is a Dell Inspiron 1720 (purchased in 2006). About a year ago, I updated to Windows 7 from the pre-installed Vista. Never had any problems (as I said, everything was fine up until about a week ago). The installed card is a Broadcom 440x 10/100 Integrated Controller. Everything under Device Manager indicates that the hardware is working properly and has all of its drivers installed, but nothing is working.I have tried to uninstall and re-install the drivers (albeit by allowing windows to find them automatically), but the result is the exact same.I have checked the port and found that there is no debris or obstructions. My computer hasn't been dropped or mishandled in any way.I'm currently being housed on the campus of Delta State University, which is why this appears, but here is the report: [code]
I just installed windows xp pro 64bit and i am not able to use it im guessing because i need the correct driver, ive tried looking around but couldnt find anything. I also try it working with Windows 7 ultimate (64bit) and i could not get it working on that either.
Trying to set up a simple schedule for keeping the kids from staying up all night. I'd had this working on a Linksys WRT54G till it bit the dust. I just want it to block internet after midnight. My problem is that the schedule is triggering the block unpredictably.?
I have configured my CIsco 2911 router and there seems to be something wrong with my configuration regarding subinterface 0/0.102 The hosts on this subnetwork cant access the Internet and i cant spot the error.
Here is my running config on this matter.
class-map type inspect match-any LAN_TO_WAN match access-group name LAN_TO_WAN class-map type inspect match-any WAN_TO_LAN match access-group name WAN_TO_LAN class-map type inspect match-any GRE_TO_WAN match access-group name GRE_TO_WAN class-map type inspect match-any WAN_TO_GRE
I have a user using windows 7 64 bit. I tried vpnclient-winx64-msi-5.0.07.0290-k9.exe and vpnclient-winx64-msi-5.0.07.0440-k9.exe. Installation is fine. Connecting is fine. But no traffic goes through.The remote end cisco is 1811 VPN Server split tunnel. User get authenticated by Radius server.
After connected, user get the correct IP address. In router, sh crypto session, it has SA, etc. But sh ip route, can't find the Static route point back to the client IP like other connections.
At user end, windows show the IP address but no gateway. Windows route print shows the VPN network via gateway xxx.xxx.xxx.1 which is not available.Other 32bit users have no issues with VPN.