i want to monitor interface traffic in/out by eem and the if the values is overer than some value i will change the policy. for example my router is 2821 is have 2 fastEthernet port , i want to monitor the traffic on fasE1/0 if traffic over than 80Mbps i will change some configuration ( example: change next-hop on static route) for via traffic to interface fasE1/1 for reduce the traffic on interface fasE1/0?
View 6 RepliesWe have cisoc 2821 at one of branch and created five sub inetrfaces for different vlans.Output of Show interface shows very frequent increase in the input error count.I have changed the physical cable and switch port on the other side.But still error rate is increasing.When the traffic is less error rate is low but with high traffic it is increasing drastically.My router process is very less(4%) only.What could be possible reason. [code]
View 8 Replies View Relatedi have 2 routers, 2821 and 2811. they are connected via GRE over IPsec, and all of the traffic from 2821 is being routed to 2811 with a default route to its tunnel interface. 2821 needs to access internet through 2811 valid ip address, my question is that how should i nat the traffic on 2811 so that 2821 can access the internet?
View 1 Replies View RelatedI have a 2821 router with two T1 WICs and have the need to route FTP down one T1 and all other TCP traffic down another T1. All traffic is going to the same remote IP address. The remote sites are in different states, and I assume that the remote subnet is being bridged between the states. It's kind of a weird set up, but it's not my design.
Anyway, can I use a route map to split off FTP traffic to host A and send it down one T1 and have the rest of the IP traffic to host A go down the other T1? I also need to be able to have all traffic use one T1 in case the other T1 goes down.
My first thought was to static all IP down T1-1, then route map FTP traffic down T1-2, then have a floating static for all IP traffic down T1-2 with a higher metric. But something would have to track the T1 interfaces and I'm not sure if route maps or static routes can do that. Any thoughts on this?
I have a Cisco 2821 with ios Version 12.4(21). On that router I have a WAN link that is 550mbit dual. The interface is 1000FD so i need to shape my output traffic to max 550mbit - otherwise my ISP policing is dropping the traffic.
I've looked at this document url... and i'm trying to use this interface command:traffic-shape rate
But the router wont accept rate value 550000000 that should be 550mbit in bits/s
Is it not possible to shape the traffic to 550mbit on the 2821 router?
I'm using a Cisco 2821 router to provide temporary Internet access for a private network of about 300 users for a conference at a hotel. The hotel has provided me a public IP address for the WAN side. On the LAN side I have a 10.x.x.x /8 subnet with the router providing DHCP and NATing (overload) across the WAN interface.
Users can pick up an IP address and access the web. Light web pages such as Google tend to load without issue, however if a user does something that takes more time, such as streaming a Youtube trailer or opening an RDP session, the connection will freeze.
It doesn't appear to be related to bandwidth availability. Pings return on average 10-15 ms. However, I will get a request time out about every 10th continual ping. Steaming video will load about 4-6 seconds worth of data, then will appear to freeze without dropping. Doing something like speedtest.net will send a large amount of data then will hang, without ever ending the conversation.
This doesn't happen when I plug a laptop directly into the hotel public Internet line. They also don't have issues with their network similar to this.
I do not have any ACLs, etc. loaded. The router is basically wide open as far as I can tell. I don't see the router resources getting used much at all.
I have hooked up to the Cisco 2821 router a T1 on Serial and Cable Modem to GigEth0/1 and I want to split outbound traffic so that all regular users will use G0/1 interface for web traffic and the rest of the traffic stays with the T1. I am having an issue where the users on the network are not able to use the internet when using the following config:
!
interface GigabitEthernet0/0.10
description Data
encapsulation dot1Q 50
[Code].....
MPLS customer with 4 T1s in a multilink. If one of the T1s drops there is a brief delay in traffic picking back up and I actually lose packets from premise back to CO. You can see this loss both with pinging across the circuit and with techs on either end running JPerf. It can take as long as 6 seconds for the reconvergence to actually happen on the multilink and traffic picks back up. In my experience this is normal behavior for Mulitlinks
I'd also like to note that it is indeed much quicker reconvergence when you physically pull the T1, any of the T1s, rather than administratively shutting down one of them and I understand that the hardware is quicker than software and that's a good thing, obviously. I've tried this with and without ppp mulitlink fragment disabled on either end and every other combo between the two. Each of the 4 serial interfaces are on line timing and I tried free-running just on the off chance that it could imrpove the loss, but it gets worse.....back to line timing. I've even tried this on other CPE platforms like two different versions of Adtran CPEs and I get the same thing. Currently I have a new 2821 CPE in place and still get the same thing. Still see a brief amount of traffic loss up to 6-7 seconds or so at times.
7600 side:
interface Multilink592
ip vrf forwarding ******************
ip address *************************
load-interval 30
no peer neighbor-route
ppp multilink
ppp multilink group 592
ppp multilink fragment disable
no cdp enable
service-policy output VPN-TEMPLATE-2(code)
I have a Cisco 2821 with two serial interfaces bundled using PPP multilink. I want to monitor traffic flow (net flow) on the multilink interface. I have tried configuring ip route-cache flow/ ip flow ingress / egress but no luck.The other thing is when I do sh ip cache flow I guess I should see the multilink interface in both Source and destination columns which is not happening (not showing in destination column).The other router with same config but with ATM sub-interface working properly (same IOS). Are there any hits on this ? Also, is it possible to use SPAN feature ? The monitoring server is at some other site (coming via WAN).
View 1 Replies View Relatedis there a way to get traffic and client access/associations data with WCS for each AP of a centrally managed WLAN?I manage a campus WLAN with a 4402WLC (software version 6.0.188.0) and a WCS version 6.0.170.0 .WCS provides me detailed information on a client basis: I'm able to know the association history of each client currently connected, both which AP the client has connected to, and how much traffic the client has generated/ received for each connection.I hadn't find a way to get the same information on an AP basis. Namely, which clients have been connected, and how much traffic has been transmitted per time slot. I suppose this is just a matter of making a different query to the WCS database, since the data are the same used for providing the information on the client association and traffic history. Though, I haven't find a way on WCS to get this information.
View 2 Replies View Relatedi have a core switch of 4500 series. some system are generating the traffic Extra LAN traffic. how i can monitor on switch that which system is generating the traffic,
View 1 Replies View RelatedOn a 2821 Router with 15.1(3)T1
I have an IPSec VPN and NAT configured. Return traffic from an internal NAT host seems to be blocked by the WAN inbound ACL. What is the proper way to allow return traffic from the Internet for this internat NAT host? Note: As a test, removing the deny entry on the WAN ACL allows return traffic.
I am supporting a small call center of all Win7 machines. There is no server in house as everything is web based. Anyway, we want to find the bandwidth hogs and programs that I am used to using require servers for monitoring web traffic.
Are there any devices or software that is not a fortune that can give details on bandwidth usage?
i need to monitor the traffic on a multi users wireless route
View 8 Replies View RelatedISP has recently announced that they are going to start charging $1 for every GB that their customers go over their monthly limit. i have a 100GB/mo package and i figure that's sufficient for my habits which consist of approx 40GB of torrents, a bit of skyping, bit of browsing, etc. my ISP makes usage graphs available online, when i checked earlier last month to confirm i'm staying under my 100GB limit the graphs said over the past 12 months the highest i topped was 90GB, usually in the 70's. pretty much what i expected. but when i check their usage graphs again recently it says i've been using over 400GB for the past 3 months straight (as far back as the new graphs go). i call BS and find it very suspicious that my internet usage magically quadruples the same time my ISP wants to start charging for overusage, especially retro-active.
anyhoo, i want to somehow monitor my internet traffic usage independently but i'm not sure the best way to go about it.my home network is the typical modem -> router -> LAN.my router is a new netgear wndr3700, it has a traffic meter built in, but considering it's only forms of notification is cutting the internet off altogether or changing a green blinking LED to and orange blinking LED when the defined limit is reached, it's kinda useless. i just got it a couple months ago too, so buying a new router with better traffic monitoring isn't an option.i could put a net meter on each and every computer i have, then sum up their usage stats, but that would be a pain in the ass and wouldn't take my PS3 or WDTV media player into account, as little as they're used online.my prefered solution is to use an old laptop i hardly touch anymore and set it up as a gateway and share the internet connection or make it a proxy server. that way i could set up a net meter on just the one NIC on that to track my internet usage. modem -> laptop -> router -> LAN. the problem i have hear is forwarding ports from one NIC to the other so they can then get ditributed by the router, never tried this before, not sure how to go about it. right now it has XP home, but i can put 7 on it if that's better to work with.
I keep getting warning on bandwidth usage , I'm using a dir-615 routers xp on all machines . The one pc that i use to d/l with I have the torrent monitor on and shows little traffic. Ive heard of a few pieces of s/w but these require software to be installed on all boxes Id like to be able to monitor from one box if possible ??
View 2 Replies View RelatedI have a problem with the command mls qos trust dscp, I used the ios c2800nm-ipvoice_ivs-mz.124-25f.bin but i can not enable dont show me the complete command in the interface Ethernet o Giga. I want to configuring mls qos trust dscp.
View 1 Replies View RelatedI am having an issue pinpointing why my 2821 router is discarding so many packets when transferring data to our second site. The traffic flows from the local lan, to the router, where it is redirected via WCCP to a WAN optimization device, back to the router and over a GRE tunnel to the second site where the same process happens. The traffic does get there, but the LAN/Repeater router interfaces have around 20,000-60,000 input drops an hour. From the output below, it looks like traffic is being dropped by the RP.
I just restarted the router as a last resort, and here is what has accumulated in the last 30 min:
FastEthernet0/0/1 is up, line protocol is up
Hardware is Fast Ethernet, address is 0025.840c.7680 (bia 0025.840c.7680)
[code]....
And CPU never goes above 40%
100
90
80
70
[code]...
I have a two ASA 5520's and I want to be able to see or monitor the traffic between each tunnel. I am using external addresses but for the sake of this question I will use the following: 1.1.1.1 to 2.2.2.2 . How can I montior the traffic?
View 3 Replies View RelatedI have an RV042 router and I'm looking to monitor the total upstream and downstream traffic from within the router.
I know there is tons of software that I can put on a network computer to monitor traffic, but is there any software that I can put on the router itself that will monitor the traffic from within the router?
I'd really like to be able to monitor DSL traffic on my X2000. SNMP is the logical way to do this; Looking at the source to the Management screen, it looks tantalizingly close, but the SNMP bits are commented out in the HTML.
View 4 Replies View RelatedI have some issue on Card Hwic-D-9ESW with Router 2821, i was install card 9ESW in to router 2821 on slot 2 and 3. After I show run, the Cisco Router 2821 have interface F0/3/0 - F0/3/8.and i configure V lan already and interface up also.
When i connect PC to port F0/3/0, the interface is up, but i cannot pint go interface, i mean it request time out. My question is, Is it correct that i install card into slot 2 and 3?
What is the problem all port up but i cannot ping to interface?
Note: the same V lan
we're facing a weird issue lately with a Cisco 2821.An interface stops responding after a few hours.The only way to bring it 'up' again is:
Hardcode: duplex or speed
or
shutdown -> no shutdown
there are no errors in the "sho interface" and no errors or entries in the log.
FastEthernet0/0/0 is up, line protocol is up
Hardware is Fast Ethernet, -
Description: Infopoint
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
[code]....
Both regular IP traffic and ICMP traffic are passing through the source port. C6509 provides the option of filtering vlan traffic during monitoring. But I don't have vlan traffic.
qa-c6509-c(config)#monitor session 1 filter ? vlan SPAN filter VLAN
So I applied an access-list which only allows icmp traffic to be sent out of the monitoring port. But it does not work.
I was previously using SDM for our Cisco 2811, and this past week installed CISCO Configuration Professional so I could have access to a bandwidth/traffic monitor.
I have successfully started the monitoring service and monitored traffic from within CCP, but it appears that if I turn off the computer I am using to monitor the traffic, it stops collecting data until I start CCP and the monitor up again.
Is there a way (maybe with IOS console commands) that I can have the monitor always running, so I can pull up, say, a week's worth of info at any time? Leaving the computer on all the time is not an option, and currently I have only a few days of data, then a big empty chunk, and then what I have collected since I started it back up today.
I have Pix 501 firewall and I'm just configuring the device for "Email Server" to allowing POP/SMTP.
Inside Interface Address: 132.147.162.14/255.255.0.0
Outside Interface Address: ISP provided IP address
My question is can my traffic goes from inside interface to outside interface? (because the inside interface address not from 10.0/172./192.168 private address)Also I'm allowing internet from this email server (132.147.162.14) so what my access list to be configured? and what my subnet mask shoud be there?
Pix(config)#access-list outbound permit tcp 132.147.162.14 255.255.0.0 any eq 80
Pix(config)#access-list outbound permit udp 132.147.162.14 255.255.0.0 any eq 53
Pix(config)#access-group outbound in interface inside
I have a Belkin G router F5D7230-4 (firmware version 8.01.07) and am trying to view stats on what is using our connection.We have a very low capacity, rural wireless broadband that our ISP tells us is maxed out all the time, even when we don't appear to be using any devices, so I'd like to view the traffic on our DHCP client list to see which device is using an excessive amount of bandwith and put a limit on its access.I don't see a statistics tab on the setup page, is there another place to look or does Belkin have an external program to do this?
View 1 Replies View RelatedI am trying to find a tool that will monitor the web traffic for one specific user. If it is capable of bundling it into a report that would also be a benefit. I have searched, but not come up with much aside from broad network monitoring tools. All that is really needed is to capture all the activity from http traffic for this one specific user/PC (since she uses the same PC all the time). We have a Sonicwall NSA 2400 as our internet filter, but I was not able to locate anything on there for specific user reporting.
View 2 Replies View RelatedHave a PC set up with a LINKSYS N2500 router. this is password protected for access to network I would like to monitor what one of my children is doing on the net - but they surf the net using an iPad
View 4 Replies View RelatedI just got optical fiber installed in my place which gives me great download speeds. Now my ISP has a monthly download limit of 120GB, after that I gotta pay overages.Now my setup is like this: Fiber modem (1 port) -> Linksys E3000 router (4 ports + wifi).All my gear is hooked up to the Linksys router (xbox, ps3, media center, office pc & 2 laptops).I would like to keep track of the total "internet" bandwidth use of all devices, but exclude the normal network traffic, as that of course I don't pay for.Is there something that I can install on the Linksys router that can keep track of that kinda of information? router (4 ports + wifi).
View 6 Replies View RelatedI have a WRT160N router. Are there any network software packages out "there" than will allow me to track the total traffic on this device?
View 1 Replies View RelatedAny Cisco command similar to Junipers monitor interface interface type / number. It's handy seeing real time interface stats. monitor interface?
View 5 Replies View RelatedDoes one can use a Vacl to monitor network traffic on a nexus 3064 much like you can on the 6500s? If so, any performance tradeoffs or caveats to be aware of ?
View 2 Replies View Related