I have a wireless controller 5508 and all my interfaces can be accessed via https or ssh from a wireless client. Management access from a wireless client is disabled so I don't understand why this is happening.
View 10 RepliesNew 5508 controller, can ping it and ssh but no https. Is there an initial cli configuration I'm missing here ?
View 2 Replies View RelatedInterface management on WCL 5508 is assigned ip 192.168.255.200 and from a PC ( on different subnet), i can ping but cannot access https to WCL but From a PC ( in the same subnet) i can ping and https.
View 11 Replies View RelatedI'm trying to verify some behaviors I'm seeing with my 5508 controller setup, I've zero experience with this hardware and clueless on the best practices. With that said... out of the box I ran through the AutoInstall process.
I gave my service port an IP address on my subnet, 10.10.8.0/24 vlan 100 and gave the management interface the ip address 10.10.30.5/24 vlan 130
From my host I can ping the management interace 10.10.30.5 and the interface gateway 10.10.30.1
I cannot connect to the controller via 10.10.30.5 either through the web GUI or telnet
I can connect to the controller via 10.10.8.200 both through the web interface and telnet
while connected to the service port, I can ping the management port IP but I cannot ping the 10.10.30.1 gateway.
We have attached two test 3502I AP's and they found the controller and pulled correct ip addresses, clients can authenticate and access network resources as well as the Internet so for the most part, things are working but it concerns me that the management interface can't ping its own gateway.
I configure IP address on the management interface port 1 of 5508 controller when i connect it direct to my laptop i can't ping or access controller from my laptop even i connect through layer 2 switch still i can't not.
IP Address of management interface : 10.21.0.50
Laptop IP Address : 10.21.0,51
I know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
View 7 Replies View RelatedWe have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
View 2 Replies View RelatedI have follow below URL to disable the https over web authentication:
[URL]
What i want to achieve is disable https over web authentication due to certificate issue, but it seems like even we have disable the http over web management as above URL describe, still https while doing web authentication. Or it is possible to configure use port other than 80, like 8080 for web authentication? (need to reboot the wlc?)Is there any bug that related to this CSCsy32145?
WLC Software Version 6.0.196.0
I have a guest wireless network setup on a 5508 WLC using 7.2.103.0 firmware. Under my guest WLAN>security>Layer3 tab I have "layer 3 security" as "none", "web policy" as check marked, "passthrough" selected, "over-ride global config" as check marked, "web auth type" as "customized(downloaded), "login page" and "login failure page" as "login.html" selected.
I haveI have 4402 WLC's using 7.0.116.0 firmware throughout my company that anchor back to the 5508 for the guest network. The 4402 WLC have the guest network configured as WLAN>security>Layer3 tab I have "layer 3 security" as "none", "web policy" as check marked, "passthrough" selected.
I would like to disable the HTTPS for the logon screen and I am not sure what steps need to be done for this. I researched and found the command "config network web-auth secureweb disable". I set the command on the 5508 only and rebooted. When I tested I got a blank webpage with "http://1.1.1.1/fs/customwebauth/login.html?switch_url=http://1.1.1.1/login.html" in the address bar and had no way of clicking the accept button to get to the Internet.
Everything works fine again if I enter "config network web-auth secureweb enable" and reboot. Do I need to run the "config network web-auth secureweb disable" command on all the 4402 WLC's that are anchored to the 5508? What could be breaking my login.html page while using only http?
I have a Cisco 5508 running version 7.0.116.0. This controller hosts an open public wifi that requires users to accept a terms agreement via a Web-Passthrough setup that redirects them to the terms splash page. For most people this works without any issue. However, if a user has their homepage for their default browser set to a https site, such as [url]..., then they are never redirected to the terms splash page. The page will just spin and spin until finally they get a timeout error.
View 7 Replies View RelatedConfiguring an asa 5505 with 8.42 software.I need to access an https server on the inside via the outside interface. have moved the http server enable to port 10443.Tried to make a "network object nat rule"
object network Vejrstation nat (any,outside) static interface service tcp https https object network Vejrstationnat (any,outside) static interface service tcp https https.
I have an ASA 5505 with the base license,When I setup the DMZ interface I had to add the deny access to the inside VLAN. The DMZ works fine with WiFi on it, but user's iPhones can't get email unless they turn WiFi off.Is there a simple way to allow HTTPS traffic through the DMZ interface to our internal Exchange server which is NAT'd on the 5505's external IP?
View 3 Replies View RelatedI was unable to access the web admin on my WRT160n v3 w/ latest firmware this morning. Reset config to defaults & was able to get in. Enabled HTTPS access & disabled HTTP access & was right back where I started; reset to defaults again & left both boxes checked. Can access via HTTP, but HTTPS requests get refused/reset.
The reason I needed access was that when I booted up my laptop this morning, my wireless card wasn't picking up an IP address via WIFI, only worked via ethernet, so I need to see what was going on there — several reboots of the router didn't fix, nor has it fixed the HTTPS access problem described above.
Just upgraded my E4200 to firmware 1.0.03 (from 1.0.01). I have some new issues, questions, and some outstanding issues.
1) Web interface over https is now painfully slow.
2) Does DDNS work in bridge mode? DynDNS allows the sending of an update without an IP address, so it should be able to work.
3) Does accessing the management interface in bridge mode count as local or remote?
4) I'd really like to be able to get WOL working through the router. I managed to create a static DHCP reservation for 192.168.1.254 to ff:ff:ff:ff:ff:ff, but I don't think the router added that entry to the ARP table, is there any way to do this.
(I think have WOL forwarded to 192.168.1.254). 5) Should the router be providing some local dns hostnames? For example I have the device name set up in the local network setup, but it won't resolve. Similar for connected devices, especially those with with a DHCP reservation. 6) In bridge mode, does it matter which port is used to connect to the other network device? Does it have to be the WAN port?
I want to use a 5508 as an anchor controller for a wireless guest deployment....but the client has internal 4402's controllers, with software version 7.0.235.0...is it possible tu mix these two controllers for a Wireless Guest Access Deployment??
View 3 Replies View RelatedA wlan on my controller is configured for WPA2, AES encryption and a PSK. A vendor will supply me with a wireless device for this wlan. The vendor asks if we use AES 128 or AES 256. I had always believed we use AES256 but I can't verify this. How can I verify this to the vendor?
View 1 Replies View RelatedSeems that all solutions are null and void for us because we are not using SNMP v3 or H.
We are using SNMP v2, We have upgraded our WCS to latest version as well as the controllers. I have 6 controllers currently added although they are on WiSM blades.
We are unable to add the 5508 Controllers, we keep recieving this error -
No response from device, check SNMP communities, version or network for issues.
I have confirmed all connectivity is working, even with a debug on the controller you can see it sending SNMP packets to the WCS, although still same error.
We have a customer that is looking to allow only static IP addresses onto the wireless network via the new 5508 we are putting into place. I can see where to require DHCP but not the opposite.
View 4 Replies View RelatedIs it possible to block outside P2P traffic on a guest wireless network using an ACL on the controller? I know we can do it our firewall
View 6 Replies View Relatedi'am trying to configure an AP1121g on my controller wlc5508 7.2 but i'am facing a compatibility issue.
View 5 Replies View RelatedI have a 5508 controller at our headquarters and am installing some 3502 AP's at a remote branch. Unfortunatly, the remote branch has a different Vlan setup for some reason and the vlan that is used for the WLC (90) is designated for telephony at this branch. Can I put the AP's on a different VLAN (10) without having any issues? I will still use DHCP option 43 to point them back to the controller. Below are the configs for the WLC interfaces and what I am proposing for the AP interfaces:
WLC Config
interface GigabitEthernet1/1/38
description WLC01
switchport
switchport trunk encapsulation dot1q
switchport trunk native vlan 90
switchport trunk allowed vlan 1,10,50,90,91,390,410-413,610-613,800,810,811
switchport mode trunk
[code]......
Web Auth on 5508 running 7.2.103.0.
Issue 1: I have been trying to configured Webauth bundle however it seems that is not working.
1. login.tar created use picozip contains 3 files: login.html, terms.html, and logo.jpg.
2, uploaded via FTP to controller successfully..
3, no issue when i tried to preview on the controller
However users unable to see the login page when connected to guest wifi. when the user tried to connect cisco.com, on the browser address shows that the page redirected to url... however internet explorer / firefox display "Connection reset error".During this time, if i ask the user to type url... they can see the default login page, so no issue on connectivity to the service port.
Issue 2: Since i couldnt make that work, i have use default webauth internal. its all good. then when i tried to upload customlogo.jpg (18k size). User able to see the login page however not the logo. it shows broken image icon on the web browser. --> i can see the logo when i did preview on the controller.
Issue 3: last resort if i couldnt get the answer by sunday, how do i delete or remove the customlogo ?? so by monday users will not be seeing any errors on the page.
Cisco 5508 Series Wireless Controller for up to 100 APs 802.11a/g/n Ctrlr-based AP w/CleanAir; Ext Ant; E Reg Domain..For Mobility i want to settup the device such that the SSID would be the same with thesame security key and in different subnet.
View 5 Replies View RelatedI can not get our 3602i AP's to register with our 5508 controller which is running 7.2.103.0 code. We keep seeing an error in the log on the WLC "AAA Authentication Failure for UserName:c46413c08e92 User Type: WLAN USER" and on the Access Point we are seeing [code]
I entered the CAPWAP ap controller ip address directly into the AP so it shouldn't be an option 43 DHCP issue
I use WLC 5508 (ver 7.0.116.0) with aironet 1140. I need to connect my APs to different controller .After log in via ssh to AP i am trying to do:
capwap ap controller ip add x.x.x.x
reset
But after reload, AP is still joined to the old WLC. So another idea was to log to that WLC and put:
config ap primary-base WLC2 AP_NAME x.x.x.x
and after that:
config ap reset AP_NAME
But still nothing, it's joined to another controller although "show ap client config" shows that primary-base switch is x.x.x.x ?How can i force it to join to other controller?
We are looking to upgrade our 5508 wireless controller from 7.0.98.0 to 7.0.220.0. Reason being, we have experienced a lot of access points disassociating from the controller as well as client authentication issues. Upgraded from 7.0.98.0 to 7.0.220.0 and any issues during the upgrade or after the upgrade?
View 3 Replies View RelatedWe have a WLC (5508) in our main office in Brisbane that is hosting two WLANs. One provides wireless access to our internal network and the second provides wireless guest access. The guest WLAN is anchored to a controller sitting in the DMZ at our Data Centre.
In the DMZ the anchor controller has a management interface and an interface in the DMZ for the wireless guest access. I am using the DHCP server on the anchor DMZ to provide IPs etc to wireless guest clients. The default gateway is 10.8.144.1 which is a VIP or a pair of firewalls.
Initially everything works fine. Guests connect to the guest network, have to authenticate via a web portal (Cisco ISE server) and then can go on an use the internet. Works perfectly until the firewalls fail over and the secondary firewall takes over the VIP address. All access to the internet is lost at that point. If I try to disconnect and then reconnect a wireless client it connects, as in it will get an IP address, but DNS resolution stops and I do not get redirected to the web auth portal. If the firewalls are failed back to the primary then everything works again, no issues. However, if I reboot the WLC while the secondary firewall has the VIP IP everything will work fine as it did on the primary. If the firewalls now fail over to the primary again everything goes to ****. Until either the firewalls are failed back or the anchor WLC is rebooted.
Initially I thought this was an issue on the firewall, but this doesn't appear to be the case. When the firewall fails over it sends out a gratuitous ARP advising of the change in MAC address for the 10.8.144.1 IP address. The WLC seems to update its ARP table because if I run the command "show arp switch" it has the 10.8.144.1 IP address with the MAC address of the active firewall. From the client perspective I have run a wireshark and captured packets on the wireless interface when trying to connect. The laptop is continuously send ARP requests for 10.8.144.1 but gets not reply. Without this the client cannot send an ethernet frame to the gateway and hence get to the DNS server and WEB portal. Internet access breaks. Doing a TCP dump on the active firewall shows it receiving and then sending a reply to the ARP request. It just never gets to the wireless client. Debugging ARP packets on the anchor WLC seems to indicate that the controller is receiving the ARP replies from the firewall. So I'm at a loss as to why things should break when the firewalls fail over.
I have a 3750 switch in the DMZ with SVI of 10.8.144.4. I thought I could get a work around where I would make this the default gateway. The theory being that this interface MAC address would never change. However I was wrong. Even with this IP set as the gateway address for the wireless clients I see the exact same bahaviour when the firewalls fail over. I can't explain it other than to say that the gratuitous ARP sent by the firewalls seems to kill the ability of ARP replies to be sent back to the wireless client.
I'm a trainee in Network and Telecommunication, and I have to do a "model" with a controller, an AP, and a RADIUS server. Communication and configuration of the lightweight AP has been done.
I use an autonomous access point 1220 as the RADIUS server (no considering it as an AP), and I'm a beginner in RADIUS configuration. I get a "Processing AAA Error 'No Server' (-7) for mobile 00:24:d6:8f:2c:7e" when I launch a debug targetting my PC, connecting to the LAP.
Precursory : 10.137.125.71 is the IP address of the ap1220, working as the RADIUS server 10.137.125.15 is the IP address of the controller. 00:24:d6:8f:2c:7e is the MAC address of my PC, connecting to the Wi-Fi. ping works to the RADIUS, to the controller. Each devices are connected by a layer 3 Switch, and ping each others. The Wi-Fi works when I don't use 802.1X (or when I don't use RADIUS authentication at all)
What I did on the RADIUS server (ap1220 autonomous) :
aaa new-model
radius-server local
nas 10.137.125.15 key password
[Code]......
Have a controller based depolyment with (2) 5508s and an 1121 ACS appliance running 5.1 code. Controllers are setup identically and we are radius authenticating users to AD via the ACS. Everything works great on the primary controller, but when I test failover to the secondary controller, my authentication fails and I get the following error message in my ACS logs:
12126 EAP-FAST cryptobinding verification passed
12147 Machine Authentication is disabled
12161 Cannot provision Authorization PAC when the stateless session resume is disabled
12106 EAP-FAST authentication phase finished successfully
11503 Prepared EAP-Success
Just replaced a 2106(ver 5.1) with a 5508 (ver.7.2)...Everything was OK.. AP's got on 5508 and we shut the 2106. (AP's are on L2 with controller)During some investigation of why new LAP's from a location via VPN/GRE don't show up in controller, i type the following command on 5508: test ap pmtu enable all....All AP's on 5508 is now in Not Joined state..Have powered up the old 2106 and put AP's on that .. This is OK ....Have rebooted/downgraded/upgraded the 5508 controller but with same result.....No AP's can join this controller (exept from a oeap600)
View 8 Replies View RelatedSo we have a Cisco 5508 controller that is managing 15 AP's in one of our buildings.I am running 2 wlans, one is internal access via (wpa) radius, peap and domain login...that works well now
The other is a guest lan, that is only allowed to surf the web.
The question from our security group, is there a way to restrict wireless access to ONLY a corporate approved list of devices.
As it stands right now, we only support Blackberry's as our mobility device. All local data is encrypted. The issue here is our testing shows that with an Iphone (not approved) it is very easy to connect to the WPA network if a user knows how to enter in their domain credentials. From there they can browse our internal web servers and download corporate data to a non approved, non encrypted device such as the iphone.
Did any know that how many AP Groups can be created by one Controller? (5508) May I have 100 AP Groups?
View 3 Replies View RelatedI upgraded a controller yesterday 5508 it went from a low code version 6.x to 6.0.196.0 then to 7.0.116.0. However although all the access points joined code 6.0.196.0 they refused to join 7.0.116.0. The aps are all 1242s.
The country codes etc were all fine so I do not understand what was going on.
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Discovery Request from 10.0.0.183:55065
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discovery Response sent to 10.0.0.183:55065
[code] ......