Interface management on WCL 5508 is assigned ip 192.168.255.200 and from a PC ( on different subnet), i can ping but cannot access https to WCL but From a PC ( in the same subnet) i can ping and https.
View 11 RepliesNew 5508 controller, can ping it and ssh but no https. Is there an initial cli configuration I'm missing here ?
View 2 Replies View RelatedI have a wireless controller 5508 and all my interfaces can be accessed via https or ssh from a wireless client. Management access from a wireless client is disabled so I don't understand why this is happening.
View 10 Replies View RelatedWe have an MPLS (layer 3) network 4 offices and a Data center. We are planning to install about 10 Access Points(3600 series) per office and have a controller(5508 series) in the Data center.
Questions:
1- Is this design possible, in other words, just one controller centralizing all Access point traffic in one controller in the Data center?
2- We would like to accomplish this in two phases:
A- install access points without controller handling authentication thru Microsoft IAS servers (current configuration with 1200 series)
B- Deploy wireless Controller in Data center and start migrating orphan AP to Controllers one office at a time.
We are having 5508 controller with Lightweight access points 1142, IS it possible to disable 802.11a on certain access points before turning it off completely on the controllers?? Could you provide steps for doing so on WCS?
View 5 Replies View RelatedI have Cisco AIR-LAP1310G-E-K9 access point and 5508 wlan controller with version 7.0.220 and it is joining to the WLAN controller. I have enabled dhcp in the lan controller and i dont have external dns server. How to fix this issue? Can this LAN controller version will support this access point? My Lan Controller Management IP Address is 10.10.10.5 find the below configuration of 1300 access point.
AP001d.4513.dd68#reloadProceed with reload? [confirm]
%SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.%LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.flashfs[0]: 4 files, 2 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 7741440flashfs[0]: Bytes used: 2052608flashfs[0]: Bytes available: 5688832flashfs[0]: flashfs fsck took 14 seconds.Base ethernet MAC Address: 00:1d:45:13:dd:68Initializing ethernet port 0...Reset ethernet port 0...Reset done!ethernet link up, 100 mbps,
[code].....
I know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
View 7 Replies View RelatedWe have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
View 2 Replies View RelatedI have a Cisco 5508 running version 7.0.116.0. This controller hosts an open public wifi that requires users to accept a terms agreement via a Web-Passthrough setup that redirects them to the terms splash page. For most people this works without any issue. However, if a user has their homepage for their default browser set to a https site, such as [url]..., then they are never redirected to the terms splash page. The page will just spin and spin until finally they get a timeout error.
View 7 Replies View RelatedI have a requirement to set up a guest SSID for contractor so that they can use the internet while in the office.
Security say that all traffic on this SSID should be isolated and directed straight to the firewall, with no chance of contamination into the company network infrastructure.
With the 5508, my understanding is using the setting up a guest account functionality built in will achieve this, but all traffic would end up at the wireless controller. How do I then put a direct forward for all traffic to the firewall which will only affect the guest traffic?
I recently had a 5508 controller installed and configured for a corporate network as well as internet only guest access. Users authenticate via 802.1X key management on the corporate network and web authentication via guest. This works fine, however, I've run into a problem. We also use iPads for inspections and the inspection site is housed internally. I've had a network admin create an exception in the firewall that will allow connection to the internal sites from the guest network, however, it does not function. I did find that if I connect an iPad to the corporate wireless network I'm able to download the necessary certificate to the device but that only works if I use my login information which is not something I am interested in doing. Is it possible to enable another authentication for the corporate network without breaking the functionality of the existing 802.1X authentication? What could possibly be the cause on the guest network not allowing connectivity to the internal sites, even though the exception has been created?
View 3 Replies View Relatedoutput are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
I just turned on 2 Wirelless LAN Controllers 5508 and I am getting this message on both of them:
Loading primary image (Image not found)
** Unable to read "linux.pri.img" from ide 0:2 **
Loading backup image (Image not found)
** Unable to read "linux.bak.img" from ide 0:2 **
And it is taking me to the BootMenu. I selected option 4 to Clear Configuration and the controller seems to restart the system but I still get the same error. I checked the LEDs status and Sys is Amber and Alarm is OFF which according to the documentation is a System Crash.
I configure IP address on the management interface port 1 of 5508 controller when i connect it direct to my laptop i can't ping or access controller from my laptop even i connect through layer 2 switch still i can't not.
IP Address of management interface : 10.21.0.50
Laptop IP Address : 10.21.0,51
I have a 5508 controller at our headquarters and am installing some 3502 AP's at a remote branch. Unfortunatly, the remote branch has a different Vlan setup for some reason and the vlan that is used for the WLC (90) is designated for telephony at this branch. Can I put the AP's on a different VLAN (10) without having any issues? I will still use DHCP option 43 to point them back to the controller. Below are the configs for the WLC interfaces and what I am proposing for the AP interfaces:
WLC Config
interface GigabitEthernet1/1/38
description WLC01
switchport
switchport trunk encapsulation dot1q
switchport trunk native vlan 90
switchport trunk allowed vlan 1,10,50,90,91,390,410-413,610-613,800,810,811
switchport mode trunk
[code]......
Cisco 5508 Series Wireless Controller for up to 100 APs 802.11a/g/n Ctrlr-based AP w/CleanAir; Ext Ant; E Reg Domain..For Mobility i want to settup the device such that the SSID would be the same with thesame security key and in different subnet.
View 5 Replies View RelatedI use WLC 5508 (ver 7.0.116.0) with aironet 1140. I need to connect my APs to different controller .After log in via ssh to AP i am trying to do:
capwap ap controller ip add x.x.x.x
reset
But after reload, AP is still joined to the old WLC. So another idea was to log to that WLC and put:
config ap primary-base WLC2 AP_NAME x.x.x.x
and after that:
config ap reset AP_NAME
But still nothing, it's joined to another controller although "show ap client config" shows that primary-base switch is x.x.x.x ?How can i force it to join to other controller?
We are looking to upgrade our 5508 wireless controller from 7.0.98.0 to 7.0.220.0. Reason being, we have experienced a lot of access points disassociating from the controller as well as client authentication issues. Upgraded from 7.0.98.0 to 7.0.220.0 and any issues during the upgrade or after the upgrade?
View 3 Replies View RelatedWe have a WLC (5508) in our main office in Brisbane that is hosting two WLANs. One provides wireless access to our internal network and the second provides wireless guest access. The guest WLAN is anchored to a controller sitting in the DMZ at our Data Centre.
In the DMZ the anchor controller has a management interface and an interface in the DMZ for the wireless guest access. I am using the DHCP server on the anchor DMZ to provide IPs etc to wireless guest clients. The default gateway is 10.8.144.1 which is a VIP or a pair of firewalls.
Initially everything works fine. Guests connect to the guest network, have to authenticate via a web portal (Cisco ISE server) and then can go on an use the internet. Works perfectly until the firewalls fail over and the secondary firewall takes over the VIP address. All access to the internet is lost at that point. If I try to disconnect and then reconnect a wireless client it connects, as in it will get an IP address, but DNS resolution stops and I do not get redirected to the web auth portal. If the firewalls are failed back to the primary then everything works again, no issues. However, if I reboot the WLC while the secondary firewall has the VIP IP everything will work fine as it did on the primary. If the firewalls now fail over to the primary again everything goes to ****. Until either the firewalls are failed back or the anchor WLC is rebooted.
Initially I thought this was an issue on the firewall, but this doesn't appear to be the case. When the firewall fails over it sends out a gratuitous ARP advising of the change in MAC address for the 10.8.144.1 IP address. The WLC seems to update its ARP table because if I run the command "show arp switch" it has the 10.8.144.1 IP address with the MAC address of the active firewall. From the client perspective I have run a wireshark and captured packets on the wireless interface when trying to connect. The laptop is continuously send ARP requests for 10.8.144.1 but gets not reply. Without this the client cannot send an ethernet frame to the gateway and hence get to the DNS server and WEB portal. Internet access breaks. Doing a TCP dump on the active firewall shows it receiving and then sending a reply to the ARP request. It just never gets to the wireless client. Debugging ARP packets on the anchor WLC seems to indicate that the controller is receiving the ARP replies from the firewall. So I'm at a loss as to why things should break when the firewalls fail over.
I have a 3750 switch in the DMZ with SVI of 10.8.144.4. I thought I could get a work around where I would make this the default gateway. The theory being that this interface MAC address would never change. However I was wrong. Even with this IP set as the gateway address for the wireless clients I see the exact same bahaviour when the firewalls fail over. I can't explain it other than to say that the gratuitous ARP sent by the firewalls seems to kill the ability of ARP replies to be sent back to the wireless client.
Just replaced a 2106(ver 5.1) with a 5508 (ver.7.2)...Everything was OK.. AP's got on 5508 and we shut the 2106. (AP's are on L2 with controller)During some investigation of why new LAP's from a location via VPN/GRE don't show up in controller, i type the following command on 5508: test ap pmtu enable all....All AP's on 5508 is now in Not Joined state..Have powered up the old 2106 and put AP's on that .. This is OK ....Have rebooted/downgraded/upgraded the 5508 controller but with same result.....No AP's can join this controller (exept from a oeap600)
View 8 Replies View RelatedSo we have a Cisco 5508 controller that is managing 15 AP's in one of our buildings.I am running 2 wlans, one is internal access via (wpa) radius, peap and domain login...that works well now
The other is a guest lan, that is only allowed to surf the web.
The question from our security group, is there a way to restrict wireless access to ONLY a corporate approved list of devices.
As it stands right now, we only support Blackberry's as our mobility device. All local data is encrypted. The issue here is our testing shows that with an Iphone (not approved) it is very easy to connect to the WPA network if a user knows how to enter in their domain credentials. From there they can browse our internal web servers and download corporate data to a non approved, non encrypted device such as the iphone.
I upgraded a controller yesterday 5508 it went from a low code version 6.x to 6.0.196.0 then to 7.0.116.0. However although all the access points joined code 6.0.196.0 they refused to join 7.0.116.0. The aps are all 1242s.
The country codes etc were all fine so I do not understand what was going on.
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Discovery Request from 10.0.0.183:55065
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discovery Response sent to 10.0.0.183:55065
[code] ......
Ap's at remote location intermittently joins unjoins the WLC controller 5508. AP's getting IP's from DHCP server located at locan end. [code]
View 8 Replies View RelatedI have one controller 5508 that will hold 50 LAP 1262 and another Controller that will hold another 50 outdoor mesh access point 1552. Both controllers (not redundant) are at the HQ while the access points are distributed between HQ and 3 branches.
The requirements is to have the SAME 4 SSIDs on MESH and LAP each have a security type (, wep,wpa,dot1x...) on HQ and Branches. Now, in the HQ I don't think I will face a problem since the WLCs is on the same LAN, so 5 interface v lans will be configured one for the WLCs and access point and another 4 interface v lans for the 4 SSIDs.
Now, for the remote sites I need to create another vlan on the switch with DHCP and option 43 ..... for the access point to register with the controller.
But here, do I have to create another 4 interface v lans (4 different sub nets) that should be bidden to the SSID as in the HQ?
Or the Access point will encapsulate all the traffic including the client traffic? Note that I have outdoor mesh access point and Lightweight access point and the BW link between the HQ and branch is 100M.
Also Can I have roaming between the same SSID that broadcasted on MESH and LAP knowing that each have different controller.
[URL] I have one Controller 5508 is my Central Office and I have some Ap's working in local mode in my Central Office, additional I have more Ap's in a remote Office they're are working as H-REAP and I can handles across my WLC. Now my enterprise decided bouth another WLC and wants to deploy a active-passive scenario. This new Controller should manages all the AP's when the central WLC fails...
My questions are... I need to have the same ip addressing on both sites? or they can be different. I nedd to configure some on my Ap's that are working as local mode, for allow the secondary WLC manage them when mi central WLC fails
I received a 5508 WLC, that I wanted to configure as a guest anchor for our DMZ. I stepped through the console configuration. Now that the setup is complete, can I attach my laptop directly to the copper SFP, and access the WLC web portal? I gave my laptop an IP address, in the same subnet, but still can't connect to the portal, or ping the WLC IP address.
View 2 Replies View RelatedI want to upgrade a 5508 WLC from version 6.0.196.0 to the most recent 7.4or 7.3 is it ok to skip so many versions, will this cause an issue?
View 9 Replies View RelatedWe have 3 5508 WLCs (A, B, & C) and several LAPs (1140, 3500, 3600). The APs learn the controllers IP addresses through DHCP Option 43. When we setup a new site we put the IP address of the controller we want the AP to join first. Lately, I've noticed that regardless of which WLC IP I put first when I setup Option 43 the LAPs are always joining a particular controller.
View 6 Replies View RelatedI have an AIR-AP1242AG-E-K9 which had c1240-k9w8-mx.124-21a.JA loaded, I followed the link below and upgraded with Cisco’s upgrade tool to c1240-rcvk9w8-mx with no problems at all, after the upgrade I could then see the LWAP on the 4402 controller and had it working a treat.Now the problems begin, I brought it into the office where we have 5508 controllers, plug in the LWAP into our management switch and boot it up I get an IP assigned from the DHCP server and the AP goes into discovery mode but never finds the controller.I have logged the boot process but this does not give much away, our other 1100 series AP’s boot fine,
[URL]
Console Boot Log.
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
[code]....
And that is where she sits and does nothing more, I have noticed the DNS problems but the other 1100 series LWAP’s boot up after show that same issue.
We just got a new 5508 wireless controller and the question we have is : can we get wireless users to authenticate to an Active Directory server to get access to the network? I know we can get the authentication done with an RSA server, but what about plain AD?
View 9 Replies View Relatedhow to setup the 5508 Series LAN wireless controller. The online documentation are not details. What different between Service Interface IP and Management interface IP. The device IP is using what type service or management interface.
View 2 Replies View Relatedhow an AP 3500 get to be registered in a controller 5508??, so, i have seen a lot of information of wireles deployment guide but i haven't understood yet how the process or flow is for getting the AP to be registered in a controller 5508, what exactly basic configuration must be done in a controller for doing it?
View 6 Replies View RelatedOur 5508 Wireless Controller will drop MAC addresses clean out of the system. Addresses that are in use everyday just disappear. It is not a limitation issue because we are adding iPads everyday. And it is not a daily occurance, but maybe once or twice a week. Everything has been updated and it is more of a hassle than anything, I am just trying to understand what is happening.
View 2 Replies View Related