Cisco Wireless :: AIR-LAP1310G-E-K9 Access Point Not Joining To 5508 Wlan Controller?

Mar 13, 2013

I have Cisco AIR-LAP1310G-E-K9 access point and 5508 wlan controller with version 7.0.220 and it is joining to the WLAN controller.  I have enabled dhcp in the lan controller and i dont have external dns server. How to fix this issue?  Can this LAN controller version will support this access point?  My Lan Controller Management IP Address is 10.10.10.5 find the below configuration of 1300 access point.
 
AP001d.4513.dd68#reloadProceed with reload? [confirm]
%SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.%LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.flashfs[0]: 4 files, 2 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 7741440flashfs[0]: Bytes used: 2052608flashfs[0]: Bytes available: 5688832flashfs[0]: flashfs fsck took 14 seconds.Base ethernet MAC Address: 00:1d:45:13:dd:68Initializing ethernet port 0...Reset ethernet port 0...Reset done!ethernet link up, 100 mbps,

[code].....

View 6 Replies


ADVERTISEMENT

Cisco Wireless :: 1310 LAP Is Not Joining To 5508 Wlan Controller V7.4?

Mar 15, 2013

I have Cisco 5508 WLAN controller v7.4 and i have lap 1310 and it is not joining to this lan controller.  What to do?  How to join this lap to this lan controller? or how to convert it to autonomous because i dont find mode button on this access point?

View 6 Replies View Related

Cisco :: 2504 - Access Point Not Joining Correct Controller

Apr 4, 2013

I am trying to setup a 2504 Wireless Controller with a few  AIR-AP1262N-E-K9 Access Points. But i'm having trouble getting the access points to connect to the controller.The controller and AP's are setup at a local network at one of my customers. They are part of a quite large organization and are therefore connected to some of their other divisions in different contries via MPLS. The DHCP and DNS servers are therefore on a different subnet.I have confirmed that the Access Points do get a correct IP from the DHCP server and that i am able to ping from the controller to the AP. When looking at the controller it does not receive any join requests from the AP's. I have setup a console connection to the controller and 1 AP, so i can view debug information.Most guides mention that you can run different LWAPP commands from the CLI on the AP like show lwapp for example. But i am not able to run any of these LWAPP commands on my AP.

View 8 Replies View Related

Cisco Wireless :: 5508 - APs Not Joining Controller

Jul 28, 2011

I upgraded a controller yesterday 5508 it went from a low code version 6.x to 6.0.196.0 then to 7.0.116.0. However although all the access points joined code 6.0.196.0 they refused to join 7.0.116.0. The aps are all 1242s.
 
The country codes etc were all fine so I do not understand what was going on.

*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Discovery Request from 10.0.0.183:55065
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discovery Response sent to 10.0.0.183:55065
[code] ......

View 5 Replies View Related

Cisco Wireless :: Setup 2504 WLAN Controller And 1142N Access Point?

Jun 13, 2013

We are planning to setup a new WLAN using Cisco 2504 WLAN Controller and 1142N Access Point. Is it possible to create individual user accounts for the users those who all are connecting to this WLAN Network by using the 2504 WLAN Controller ?

View 1 Replies View Related

Cisco Wireless :: 5508 APs Joining Wrong Controller

Nov 5, 2012

We have 3 5508 WLCs  (A, B, & C) and several LAPs (1140, 3500, 3600). The APs learn the controllers IP addresses through DHCP Option 43.  When we setup a new site we put the IP address of the controller we want the AP to join first.  Lately, I've noticed that regardless of which WLC IP I put first when I setup Option 43 the LAPs are always joining a particular controller.

View 6 Replies View Related

Cisco Wireless :: AP1042N Not Joining 5508 Controller

Jul 6, 2012

I am trying to configure new 5508wireless controller, AP 1042N model access points are able to receive DHCP IP address from Controller, but not able to join them.

View 11 Replies View Related

Cisco Wireless :: 3502 Access Point Will Not Connect To 4400 Series WLAN Controller

May 20, 2012

I recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect.  But I am not having any luck getting into a controller.  Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc. This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers. Niether of which are set to "Master" either.

View 10 Replies View Related

Cisco :: AIR 1522 Error In Joining Wireless LAN Controller 5508

Aug 27, 2011

I am facing problem with an outdoor access point AIR-1522-K-E series which is unable to join a wirless lan controller 5508. The wireless AP is able to get IP address from dhcp server and discover the Wireless controller IP address. After this i see following status messeges on the console of AP.

*Aug 27 11:04:19.767: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 27 11:04:21.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.2.64.50 peer_port: 5246
*Aug 27 11:04:21.000: %CAPWAP-5-CHANGED: CAPWAP changed state to 
*Aug 27 11:04:21.707: %CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 10.2.64.50 peer_port: 5246
[Code]...

View 10 Replies View Related

Cisco Wireless :: 5500 WLAN / AIR-LAP1142N - Joining Access Points

Nov 1, 2012

Got a bit of a quandary with joining new access points to our 5500 series W LAN Controller. It looks like the LAP is initially able to see the W LAN controller, but after that things go sideways. The LAP is pulling a valid IP address from DHCP, and the W LAN Controller is able to ping it.
 
In the controller's AP Join Statistics we get this: 
Last AP Message Decryption Failure  
Last AP Connection Failure   -Timed out while waiting for ECHO repsonse from the AP
Last AP Disconnect Reason  
[code]...

View 7 Replies View Related

Cisco Wireless :: AIR-LAP1310G-A-K9R Is Unable To Associate With Controller 2504

Aug 27, 2012

We have other APs  that associate w/o issue AIR-LAP1141N-A-K9. However our 1 1310 is having issues..  The Controller log shows:
 
2012-08-29 21:16:51 local0.error 172.16.10.70  ITCNJ1WC01: *spamApTask0: Aug 28 21:17:15.038: %LWAPP-3-DECRYPT_ERR5: spam_crypto.c:293 Error decrypting packet (using old key) from AP d4:8c:b5:15:3c:04 (session identifier a3ddb9c5)
2012-08-29 21:17:33 local0.error 172.16.10.70  ITCNJ1WC01: *spamApTask0: Aug 28 21:17:17.037: %LWAPP-3-DECRYPT_ERR: spam_lrad.c:3642 The system is unable to decrypt image data message; AP d4:8c:b5:15:3c:04
2012-08-29 21:17:33 local0.error 172.16.10.70  ITCNJ1WC01: *spamApTask0: Aug 28 21:17:17.037: %LWAPP-3-DECRYPT_ERR: spam_crypto.c:735 The system is unable to decrypt LWAPP packet; AP d4:8c:b5:15:3c:04

[code]....

View 3 Replies View Related

Cisco Wireless :: 5508 - WLAN Controller Ip Conflict

Dec 12, 2011

We’ve recently installed a 5508 w LAN controller for my organization wireless network and each time devices connect to this wireless network they receive an ip conflict error. All devices conflict with the ip address of IP address 0.0.0.0 with mac address 00-00-00-00-00-00.

All devices event viewer has this TCP error: “The system detected an address conflict for IP address 0.0.0.0 with the system having network hardware address 00-00-00-00-00-00. Network operations on this system may be disrupted as a result.” We previously experienced the same ip conflict with 12000 w LAN network that he had used as proof of concept.

View 13 Replies View Related

Cisco Wireless :: 5508 - Configuring Repeater To Wlan Controller?

Jan 1, 2013

I have Cisco 5508 Wlan Controller Software version 7.2.103.0 and I have Cisco AIR-CAP3602I-E-K9 Lightweight Access Points network and its working fine now I want to configure the Repeater in this network.  Because there is one area we cannot layout the cable.  How to add the repeater and how to configure the repeater in wlan controller network.
 
Do i need the change the software of Wlan Controller to support Mesh Network or this version 7.2.103.0 can support the repeater because for 1 access point i dont want to upgrade the version.

View 22 Replies View Related

Cisco Wireless :: New 5508 Controller On Existing Wlan Network?

Mar 4, 2012

I've got a couple new 5508 controllers to replace my 4404's.  Im wondering though if I throw them on the network to setup, will there be any conflict with the current access points?  Will they try and join the new controllers for any reason automatically?  Is there a better way, or a best practice to provision these new controllers? 

View 3 Replies View Related

Cisco Wireless :: 5508 - Connect 3 Switches To WLan Controller

Feb 10, 2013

I have Cisco 5508 Wlan Controller and its having 6 Fiber Ports  and I have AIR-LAP1131AG-E-K9 Access Point.  Can this Access Point will work with this Lan Controller?  Can i connect 3 switches to this wlan controller?

View 1 Replies View Related

Cisco Wireless :: 5508 - Export Mac Filter From Wlan Controller?

Jan 15, 2013

I've seen a discussion about importing mac addresses into the mac filter db on a cisco controller but is there a way to export the mac filter db?  I have a Cisco 5508. 

View 2 Replies View Related

Cisco Wireless :: LDAP Configuration With WLAN Controller 5508

Apr 28, 2013

We have 5508 controller (redundant) & would like to configure Staff vlan to get authenticate with active directory.i am new to the controller device & want to configure controller with active directory (windows 2012).
 
5508 controller (Active & Standby) with 48 Access Point.(configuration Done) Guest Vlan (only for internet Access) controller based web authentication configured.

Staff Vlan   ( inside & outside ). Need to configure with LDAP authentication?

View 9 Replies View Related

Cisco Wireless :: WLan Controller 5508 - Latest IOS Version

Apr 23, 2013

What is the latest IOS version for the WLan Controller 5508 ?
 
Actually I am using, Software Version7.3.102.0 
 
I see the following at Cisco website: 

Latest Releases
7.2.115.1(ED)7.3.112.0(ED)
7.0.240.0(ED)
7.4.100.0(ED)

View 1 Replies View Related

Cisco Wireless :: 1510 Mesh AP With 5508 WLAN Controller

Feb 24, 2013

We had our wireless mesh network running with 4400 Controller and 1510 A.Ps. Now that we have bought new 5508 Controller (with SW: 7.2) and 3600 Indoor APs, we are unable to add legacy APs on our new controller. After a wild googling I have found that for 1510 APs i need to be on SW ver: 4.0. But that will lead into another situation i-e I wont be able to have my 3600 APs on WLAN Controller.

View 1 Replies View Related

Cisco Wireless :: 5508 WLAN Controller / Still Disable 802.11b Data Rates

Dec 26, 2011

Is it possible to use Cisco Band Select on a Cisco 5508 WLAN controller and still disable the 802.11b data rates?

View 2 Replies View Related

Cisco :: Wireless 5508 Controller - Guest Wlan Time Of Day Restrictions?

Oct 2, 2011

Looking to add time of day restrictions to our Guest WLAN that is currently in its pilot phase.
 
Is there a way to config time of day access to a WLAN ?

View 7 Replies View Related

Cisco Wireless :: 5508 Wlan Controller 8 Ports Activation For Switches

Mar 16, 2013

I have cisco 5508 wlan controller with 8 ports can i connect 8 switches on these port.  If i connect what will be configuration to work all these ports because only port 1 is working if i connect to switch remaining ports when i connect status showing is enable but not working. 

View 2 Replies View Related

Cisco Wireless :: 5508 / Virtual WLAN Controller Guest Anchor?

Dec 6, 2012

We are planning a WLAN upgrade and the security policy is to forward wireless Guest user traffic to the DMZ controllers. We are now considering the Virtual WLAN Controller and all AP's will register with the virtual controllers and we will use Flexconnect for Staff and internal traffic that will switch their traffic onto the local switch.
 
We wish to forward the guest traffic to the DMZ Guest Anchor controller which will be a 5508 controller. This will also offer Office Extend AP service.I have looked at teh virtual controller docs and not very clear if this deployment model is supported. Below is a diagram of what we wish to deploy and is this a supported deployment model.

View 2 Replies View Related

Cisco Wireless :: Activate Permanent License On 5508 WLan Controller

Mar 16, 2013

I wanto delete the Evalution License and i want to activate the permanent license.  find the attached snapshot of License.

View 7 Replies View Related

Cisco :: 5508 - WLAN Disable On Controller Upgrade?

Feb 6, 2012

I'm about to upgrade a 5508 controller so I can do the pre-download to the access points, but in every doc I find, it says to disable the WLAN's before upgrading.  This makes no sense.  I'm just moving code over, why do I have to disrupt my wireless network in order to move code?

View 7 Replies View Related

Cisco :: Light Weight Access Point 1242AG K9 Is Not Joining 2100

Sep 4, 2012

I have configued Cisco LAP 1242AG with statis IP.I have connected LAP to WLC.I am able to ping WLC management interface IP Address from LAP's console.LAP is failed to Join WLC with  error "Could not resolve CISCO-SAPWAP-CONTROLLER"

View 3 Replies View Related

Cisco Wireless :: 1131AG Not Joining To Controller (7.4.100)

Apr 2, 2013

My customer has an 1131AG AP, andhas Problems with joining to the controller. I did a debug and have the following output. The WLC (5508) shows the AP with  Primary SW version as 3.0.51.0. this Release does not showup in any compat matrix! It seems to start downloading the software. after a while it stops with the bolded output, twice the same Bytecount!?
 
*spamApTask0: Apr 03 09:55:59.998: 68:ef:bd:94:e7:9c 5179392 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.097: 68:ef:bd:94:e7:9c Received LWAPP

[Code].....

View 22 Replies View Related

Cisco Wireless :: 1242 Is Not Joining Controller

May 9, 2012

i have 1240 series access points which is not joining controller 5500 series. [code]

View 12 Replies View Related

Cisco Wireless :: 1130AG Not Joining Controller

Aug 7, 2011

I am trying to join my 1130AG-E-K9 AP to my 2016 WLC, but it is stuck in a boot loop and will not connect to the controller. [code] I found some details here: url... but I'm not sure what it means that I have a 'SSC AP'. I am not local to this AP, though I do have a console connection to it-what do I need to do to get it working again? It just continually goes through this error and reboots every 30 seconds or so, so it's useless at the moment.

View 3 Replies View Related

Cisco Wireless :: 1142LAP Not Joining Controller After Conversion

Dec 11, 2012

I have some remote 1142s that I converted to LAP last night.  They are not joing a WLC, but I they are online and I can ping them.  Telnet or SSH is disabled by default (WHY???). What can I do to figure out why these access points are not joining the controller?

View 17 Replies View Related

Cisco Wireless :: 1600 Series AP To Reset Before Joining To Controller

Mar 3, 2013

I have new 1600 series Access Points. I am trying to join those APs on controller but unable to join.
 
After doing config reset using mode button, I was able to join only. Please find the logs or error messages below:
 
*Mar  4 18:53:13.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.2.241.50:5246
*Mar  4 18:53:14.063: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar  4 18:53:14.079: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar  4 18:53:14.123: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
[Code] ....

View 6 Replies View Related

Cisco Wireless :: 4400 How To Get New Access Point To Be Seen By Controller

Jul 23, 2012

I have a Cisco Series 4400 WLAN controller and I'm trying to connect a lightweight AP to the controller.  I have already assigned the switch port to use my wi-fi VLAN, and have connected the AP to the switch.  After a few minutes, the light on the AP goes from green to light blue (indicating it's serving clients). When I log into he wi-fi controller to look for the Ethernet mac address of the new AP, I do not see its Mac Address.  I want to be able to rename the AP to reflect where it will be used,  but need to select the AP via its Ethernet mac address before I can make any edits like changing its name etc. I've gone through the "monitoring" menu, selected "All" and still do not see it in their via its MAC address.  I also will select the "wireless menu" which lists all the AP's on my network, listing in order from on the longest running, to just powered on.Is there something I'm missing like a "re-scan" that scan's all devices?

View 5 Replies View Related

Cisco Wireless :: Joining AP To WLC 5508 Getting Error In Logs?

Dec 6, 2012

I am tryign to join my first AP to the 5508 and am gettign this error int he logs.
 
*Dec 07 10:42:31.067: %DTL-3-NPUARP_ADD_FAILED: dtl_arp.c:2280 Unable to add an ARP entry for 0:0.0.0 to the network processor. entry does not exist
 
The management Interface is on the the same vlan as the AP , both untagged ports. the AP gets an ip address from my dhcp server.

View 10 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved