What is the latest IOS version for the WLan Controller 5508 ?
Actually I am using, Software Version7.3.102.0
I see the following at Cisco website:
Latest Releases
7.2.115.1(ED)7.3.112.0(ED)
7.0.240.0(ED)
7.4.100.0(ED)
We’ve recently installed a 5508 w LAN controller for my organization wireless network and each time devices connect to this wireless network they receive an ip conflict error. All devices conflict with the ip address of IP address 0.0.0.0 with mac address 00-00-00-00-00-00.
All devices event viewer has this TCP error: “The system detected an address conflict for IP address 0.0.0.0 with the system having network hardware address 00-00-00-00-00-00. Network operations on this system may be disrupted as a result.” We previously experienced the same ip conflict with 12000 w LAN network that he had used as proof of concept.
I have Cisco 5508 Wlan Controller Software version 7.2.103.0 and I have Cisco AIR-CAP3602I-E-K9 Lightweight Access Points network and its working fine now I want to configure the Repeater in this network. Because there is one area we cannot layout the cable. How to add the repeater and how to configure the repeater in wlan controller network.
Do i need the change the software of Wlan Controller to support Mesh Network or this version 7.2.103.0 can support the repeater because for 1 access point i dont want to upgrade the version.
I've got a couple new 5508 controllers to replace my 4404's. Im wondering though if I throw them on the network to setup, will there be any conflict with the current access points? Will they try and join the new controllers for any reason automatically? Is there a better way, or a best practice to provision these new controllers?
View 3 Replies View RelatedI have Cisco 5508 WLAN controller v7.4 and i have lap 1310 and it is not joining to this lan controller. What to do? How to join this lap to this lan controller? or how to convert it to autonomous because i dont find mode button on this access point?
View 6 Replies View RelatedI have Cisco 5508 Wlan Controller and its having 6 Fiber Ports and I have AIR-LAP1131AG-E-K9 Access Point. Can this Access Point will work with this Lan Controller? Can i connect 3 switches to this wlan controller?
View 1 Replies View RelatedI've seen a discussion about importing mac addresses into the mac filter db on a cisco controller but is there a way to export the mac filter db? I have a Cisco 5508.
View 2 Replies View RelatedWe have 5508 controller (redundant) & would like to configure Staff vlan to get authenticate with active directory.i am new to the controller device & want to configure controller with active directory (windows 2012).
5508 controller (Active & Standby) with 48 Access Point.(configuration Done) Guest Vlan (only for internet Access) controller based web authentication configured.
Staff Vlan ( inside & outside ). Need to configure with LDAP authentication?
We had our wireless mesh network running with 4400 Controller and 1510 A.Ps. Now that we have bought new 5508 Controller (with SW: 7.2) and 3600 Indoor APs, we are unable to add legacy APs on our new controller. After a wild googling I have found that for 1510 APs i need to be on SW ver: 4.0. But that will lead into another situation i-e I wont be able to have my 3600 APs on WLAN Controller.
View 1 Replies View RelatedI want to upgrade a 5508 WLC from version 6.0.196.0 to the most recent 7.4or 7.3 is it ok to skip so many versions, will this cause an issue?
View 9 Replies View RelatedHow many APs does wireless controller 5508 and WCS (version 7.0) supports?
View 7 Replies View RelatedIs it possible to use Cisco Band Select on a Cisco 5508 WLAN controller and still disable the 802.11b data rates?
View 2 Replies View RelatedLooking to add time of day restrictions to our Guest WLAN that is currently in its pilot phase.
Is there a way to config time of day access to a WLAN ?
I have cisco 5508 wlan controller with 8 ports can i connect 8 switches on these port. If i connect what will be configuration to work all these ports because only port 1 is working if i connect to switch remaining ports when i connect status showing is enable but not working.
View 2 Replies View RelatedWe are planning a WLAN upgrade and the security policy is to forward wireless Guest user traffic to the DMZ controllers. We are now considering the Virtual WLAN Controller and all AP's will register with the virtual controllers and we will use Flexconnect for Staff and internal traffic that will switch their traffic onto the local switch.
We wish to forward the guest traffic to the DMZ Guest Anchor controller which will be a 5508 controller. This will also offer Office Extend AP service.I have looked at teh virtual controller docs and not very clear if this deployment model is supported. Below is a diagram of what we wish to deploy and is this a supported deployment model.
I wanto delete the Evalution License and i want to activate the permanent license. find the attached snapshot of License.
View 7 Replies View RelatedNew to working with Wireless and the Cisco Meshing concept so have a few questions to ask.I currently have the majority of the mesh setup and configured. I have a setup with two RAPs with 9 MAPS connecting to each RAP.
First question is how many MAPS can connect to a RAP generally?Secondly how can I block other cisco AP's that are not in my mesh network from trying to connect to my AP's
The below is constantly hammering the logs for 6 devices that are Cisco close to my mesh that are not mine.
8
Sat Nov 12 23:31:53 2011
Mesh child node '58:35:d9:aa:db:4f' has changed its parent to mesh node '88:f0:77:b7:c6:e0' from mesh node '88:f0:77:b7:c6:c0'.
Mesh Node '58:35:d9:aa:db:4f' failed to join controller, MAC address not in MAC filter list.
I have only added the MAC addresses of my AP's in to my AP Policy under security. Would these other AP's affect the mesh in any way?What I am seeing is the AP's constantly changing the child to parent relationship. I have inherited this network and they have about 20 AP's all within a square mile which is absolutely overkill. Would this close proximity of AP's together be the cause for the constant child parent changes?
How close should I have RAP's together. The network was setup so two raps are about 20 metres apart and the AP's on one side connect to RAP1 and the other to RAP2?How do you deal with Radar? The install is pretty much next to an airfield with radar running and a few times I have seen all the AP's disconnect and change channels.
using a Cisco 5508 controller (code version 7.4.100.0) with an ACS appliance running version 4.1 or 4.2?I've found that the ACS constantly reports a 'Bad request from NAS' (Invalid message authenticator in EAP request). message. This usually indicates a mismatched shared secret but this isn't the case.The controller works fine opposite a Microsoft NPS Radius Server.
View 6 Replies View RelatedI know that the recommendation from Cisco for the mobility anchor feature to work well is to use the same IOS version on the anchor WLC and local WLC controller. Now I´ll install on a new site a 5508 local WLC with a newer IOS version which is installed on the other controllers ( Guest and local ). Later I´ve planned to update also the other controllers to the same IOS version. Now my question is, must I upgrade all other controller at the same time ?
View 4 Replies View RelatedI need to know for shure if the aps listed below are compatible with 5508 controller version 7.1.91.0
the ap's are
AIR-LAP1242AG-E-K9
AIR-LAP1242G-E-K9
AIR-CAP3501E-E-K9
AIR-CAP3502E-E-K9
AIR-LAP1231G-E-K9
of course I checked release notes [URL]
I have Cisco AIR-LAP1310G-E-K9 access point and 5508 wlan controller with version 7.0.220 and it is joining to the WLAN controller. I have enabled dhcp in the lan controller and i dont have external dns server. How to fix this issue? Can this LAN controller version will support this access point? My Lan Controller Management IP Address is 10.10.10.5 find the below configuration of 1300 access point.
AP001d.4513.dd68#reloadProceed with reload? [confirm]
%SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.%LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.flashfs[0]: 4 files, 2 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 7741440flashfs[0]: Bytes used: 2052608flashfs[0]: Bytes available: 5688832flashfs[0]: flashfs fsck took 14 seconds.Base ethernet MAC Address: 00:1d:45:13:dd:68Initializing ethernet port 0...Reset ethernet port 0...Reset done!ethernet link up, 100 mbps,
[code].....
I'm about to upgrade a 5508 controller so I can do the pre-download to the access points, but in every doc I find, it says to disable the WLAN's before upgrading. This makes no sense. I'm just moving code over, why do I have to disrupt my wireless network in order to move code?
View 7 Replies View RelatedI will install next week at a customers side a new Pair of 5508 Controller. They have at the moment one old 4404 with about 70 APs.So the bought the new 5508 with HA Pair.For the HA i will need 7.3 i read in the High Availability (AP SSO) Deployment Guide.There are now two 7.3 Versions, or i can choose the new 7.4 Version.
AIR-CT5500-K9-7-3-101-0.aes
AIR-CT5500-K9-7-3-112-0.aes
AIR-CT5500-K9-7-4-100-0.aes
So what software version will be the best at the moment?I will install also a Cisco Prime Infrastructure on a ESX host.For the 7.3 in can use the 1.2 , but for the 7.4 i must take the 1.3.
When you will release the latest version for Wireless router Linksys E2100L?, because I bought a MAC with Lion and I can´t use my Router.
View 4 Replies View Relatedwhat is latest firmware version is for router WRT 160n (v1). The Linksys site currently states that it is Ver.1.02.11 (11/08/10). However, on the admin page for my actual router it states v1.52.0 Nov 16, 2007. These versions #s and dates don't jive. How could I have a supposedly newer version that is older than the most recent one posted?
View 3 Replies View RelatedAll of a sudden, my GUI look like this I'm using the latest version of Safari on a MacBook and FW 1.0.04 on the E4200.When I click on one of the menu items the only thing I get is "404 File not found".
View 3 Replies View RelatedUpgrading from cisco LMS 3.0 to a higher version.
Whatdoes it require?. What is the current version? What do we need for upgrading? Are there specific codes or new need to buy new products? In case of buying new products, which are the configurations?
I know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
View 7 Replies View RelatedWe have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
View 2 Replies View Relatedwhat is the latest firmware version for d-link dir-825? It tell me that i currently got the 2.60VT, is it the last one? If no, where can i download and how the latest version?
View 14 Replies View RelatedWe are a Small company with 400-Users and currently we are using ACS 4.2 at our company.we want to upgrade and use Cisco ISE Appliance instead.
I want to know is there any major changes in configuration between ACS 4.2 and the ISE Latest Verizon.?
Is there any Hardware (Switch or Cisco AP ) compatibility issues with using Cisco ISE. (we are currently using Cisco Cat 3550 and Cisco Aironet 2600 APs with the existing ACS4.2) What ISE Series & what Soft version are the latest so i can order ?
I have a ASA5505 and currently running Version 7.2(4). I was wondering what the latest version of the software would available to me would be.
Here's a show ver
Cisco Adaptive Security Appliance Software Version 7.2(4)
Device Manager Version 5.2(4)
Compiled on Sun 06-Apr-08 13:39 by builders
System image file is "disk0:/asa724-k8.bin"
Config file at boot was "startup-config"
Hardware: ASA5505, 256 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
I am working at a client site today whom has Cisco ACS employed. Their current version is 4.1. It has been some time since I have done any upgrades on this system. What is the most current version for this appliance?
View 5 Replies View Related