Cisco Wireless :: 5508 - Configuring Repeater To Wlan Controller?
Jan 1, 2013
I have Cisco 5508 Wlan Controller Software version 7.2.103.0 and I have Cisco AIR-CAP3602I-E-K9 Lightweight Access Points network and its working fine now I want to configure the Repeater in this network. Because there is one area we cannot layout the cable. How to add the repeater and how to configure the repeater in wlan controller network.
Do i need the change the software of Wlan Controller to support Mesh Network or this version 7.2.103.0 can support the repeater because for 1 access point i dont want to upgrade the version.
View 22 Replies
ADVERTISEMENT
Dec 12, 2011
We’ve recently installed a 5508 w LAN controller for my organization wireless network and each time devices connect to this wireless network they receive an ip conflict error. All devices conflict with the ip address of IP address 0.0.0.0 with mac address 00-00-00-00-00-00.
All devices event viewer has this TCP error: “The system detected an address conflict for IP address 0.0.0.0 with the system having network hardware address 00-00-00-00-00-00. Network operations on this system may be disrupted as a result.” We previously experienced the same ip conflict with 12000 w LAN network that he had used as proof of concept.
View 13 Replies
View Related
Mar 4, 2012
I've got a couple new 5508 controllers to replace my 4404's. Im wondering though if I throw them on the network to setup, will there be any conflict with the current access points? Will they try and join the new controllers for any reason automatically? Is there a better way, or a best practice to provision these new controllers?
View 3 Replies
View Related
Mar 15, 2013
I have Cisco 5508 WLAN controller v7.4 and i have lap 1310 and it is not joining to this lan controller. What to do? How to join this lap to this lan controller? or how to convert it to autonomous because i dont find mode button on this access point?
View 6 Replies
View Related
Feb 10, 2013
I have Cisco 5508 Wlan Controller and its having 6 Fiber Ports and I have AIR-LAP1131AG-E-K9 Access Point. Can this Access Point will work with this Lan Controller? Can i connect 3 switches to this wlan controller?
View 1 Replies
View Related
Jan 15, 2013
I've seen a discussion about importing mac addresses into the mac filter db on a cisco controller but is there a way to export the mac filter db? I have a Cisco 5508.
View 2 Replies
View Related
Apr 28, 2013
We have 5508 controller (redundant) & would like to configure Staff vlan to get authenticate with active directory.i am new to the controller device & want to configure controller with active directory (windows 2012).
5508 controller (Active & Standby) with 48 Access Point.(configuration Done) Guest Vlan (only for internet Access) controller based web authentication configured.
Staff Vlan ( inside & outside ). Need to configure with LDAP authentication?
View 9 Replies
View Related
Apr 23, 2013
What is the latest IOS version for the WLan Controller 5508 ?
Actually I am using, Software Version7.3.102.0
I see the following at Cisco website:
Latest Releases
7.2.115.1(ED)7.3.112.0(ED)
7.0.240.0(ED)
7.4.100.0(ED)
View 1 Replies
View Related
Feb 24, 2013
We had our wireless mesh network running with 4400 Controller and 1510 A.Ps. Now that we have bought new 5508 Controller (with SW: 7.2) and 3600 Indoor APs, we are unable to add legacy APs on our new controller. After a wild googling I have found that for 1510 APs i need to be on SW ver: 4.0. But that will lead into another situation i-e I wont be able to have my 3600 APs on WLAN Controller.
View 1 Replies
View Related
Dec 26, 2011
Is it possible to use Cisco Band Select on a Cisco 5508 WLAN controller and still disable the 802.11b data rates?
View 2 Replies
View Related
Oct 2, 2011
Looking to add time of day restrictions to our Guest WLAN that is currently in its pilot phase.
Is there a way to config time of day access to a WLAN ?
View 7 Replies
View Related
Mar 16, 2013
I have cisco 5508 wlan controller with 8 ports can i connect 8 switches on these port. If i connect what will be configuration to work all these ports because only port 1 is working if i connect to switch remaining ports when i connect status showing is enable but not working.
View 2 Replies
View Related
Dec 6, 2012
We are planning a WLAN upgrade and the security policy is to forward wireless Guest user traffic to the DMZ controllers. We are now considering the Virtual WLAN Controller and all AP's will register with the virtual controllers and we will use Flexconnect for Staff and internal traffic that will switch their traffic onto the local switch.
We wish to forward the guest traffic to the DMZ Guest Anchor controller which will be a 5508 controller. This will also offer Office Extend AP service.I have looked at teh virtual controller docs and not very clear if this deployment model is supported. Below is a diagram of what we wish to deploy and is this a supported deployment model.
View 2 Replies
View Related
Mar 16, 2013
I wanto delete the Evalution License and i want to activate the permanent license. find the attached snapshot of License.
View 7 Replies
View Related
Mar 13, 2013
I have Cisco AIR-LAP1310G-E-K9 access point and 5508 wlan controller with version 7.0.220 and it is joining to the WLAN controller. I have enabled dhcp in the lan controller and i dont have external dns server. How to fix this issue? Can this LAN controller version will support this access point? My Lan Controller Management IP Address is 10.10.10.5 find the below configuration of 1300 access point.
AP001d.4513.dd68#reloadProceed with reload? [confirm]
%SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.%LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.flashfs[0]: 4 files, 2 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 7741440flashfs[0]: Bytes used: 2052608flashfs[0]: Bytes available: 5688832flashfs[0]: flashfs fsck took 14 seconds.Base ethernet MAC Address: 00:1d:45:13:dd:68Initializing ethernet port 0...Reset ethernet port 0...Reset done!ethernet link up, 100 mbps,
[code].....
View 6 Replies
View Related
Feb 6, 2012
I'm about to upgrade a 5508 controller so I can do the pre-download to the access points, but in every doc I find, it says to disable the WLAN's before upgrading. This makes no sense. I'm just moving code over, why do I have to disrupt my wireless network in order to move code?
View 7 Replies
View Related
Aug 12, 2012
I know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
View 7 Replies
View Related
Jun 2, 2013
We have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
View 2 Replies
View Related
Dec 21, 2010
Can a WAP4410N be used as a repeater on an existing WPA2 + EAP-TLS WLAN? The existing WLAN is on a Cisco 871W router; we hope to use a WAP4410N as a repeater to extend it.
I've not had much luck so far with the "repeater" and "WDS repeater" AP modes on the 4410. I'm either configuring it wrong, or perhaps the 871W needs a config tweak? Or perhaps the 871's wireless can't be repeated like this?
View 4 Replies
View Related
May 26, 2011
I have a Cisco Aironet 1130 Series setup as a Root AP and a Cisco Aironet 1200 Series Access Point setup as a Repeater. However i cannot get this to work. I can connect fine to the Root AP but not to the Repeater.
I receive the folloiwng error on the Repeater AP.
'*Mar 1 00:00:24.887: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response'
The Root access point is connected to a Cisco router (192.168.168.1) which is the gateway to outside and is also acting as a dhcp server.
Both SSID's and authentication/encryption match.
Im using the the below mac-address for Authenticating the Repeater to the Root with the parent 1 command. Should i be using the mac address of dot11radio 0 of the Root AP??
AP_Root#sh interfaces dot11Radio 0Dot11Radio0 is up, line protocol is up Hardware is 802.11G Radio, address is 001b.2b69.6ca0 (bia 001b.2b69.6ca0) MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec, reliability 255/255, txload 1/255, rxload 1/255
View 5 Replies
View Related
Oct 11, 2012
Can I use the WIRELESS 150 ROUTER DIR-600 as repeater or WLAN range extender?
View 1 Replies
View Related
Dec 19, 2011
how to configure Cisco 1252-AG-A-K9 Access Point Root and Repeater?
View 9 Replies
View Related
May 28, 2011
I just purchased 2 E2000 routers at BB and was assured the second one could be configured as a repeater access point. Some current messages indicate this is not possible.Will a Cisco moderator please confirm and clarify repeater options.
View 2 Replies
View Related
Oct 11, 2011
I'm reading up on H-REAP in the Deploying and troubleshooting Cisco Wireless LAN Controllers book (Chapter 13) and I would like some clarification on the except below.:"Also notice that, as part of the WLAN configuration, no mention was made of choosing and interface for the WLAN. Unless you will have APs in local mode servicing a WLAN configured for local switching in conjunction with H-REAP APs, the controller interface is irrelevant because the controller will not bridge the client traffic on the network.The H-REAP performs that function. Even if you will not be using any local mode APs, you must choose an interface to be associated with your WLAN. In this case, you could use the management interface or create a quarantine VLAN interface, for example if you do not want client traffic to be bridged by the controller if the client traffic is no longer locally switched."Our corporate office has 2 5508 controllers and 150+ APs in local mode. I'm preparing to deploy a couple of H-REAP APs to a remote site to test. Is this saying you have to choose an interface when creating a WLAN, but if the WLAN will only be used by H-REAP APs w/ local switching it does not matter which interface is used when creating the WLAN. If there are APs in local mode using the same WLAN, the interface the WLAN associates with needs to be on the same subnet as the devices connecting the the WLAN?
View 3 Replies
View Related
Oct 8, 2012
Is it possible to set an Aironet 1232AG-A-K9 as a repeater while still using a 4402 controller? I have some wireless security cameras in our parking lots that I need to extend wireless to and I have a handful of 1232 points that I am not using. I have some omni antennas and a yagi directional that I was planning on using.Everything I am reading talks about configuring the AP while in automous mode, not while running the lightweight image.
View 2 Replies
View Related
Sep 25, 2012
I'm new to wireless and I have 7 Cisco 1142N (AIR-LAP1142N-A-K9) APs. But The thing is I have to buy a WLAN controller for these APs. I checked on internet and I found the 2500 series Controllers are compatible with Cisco 1142N (AIR-LAP1142N-A-K9) APs. But I would like to know How can I find the exact supporting version of controller for Cisco Access points?
View 15 Replies
View Related
Jan 7, 2013
I have a Cisco Wlan Controller 2504 with 1042N AP (3-nos) every thing was working fine from past 2 months. Now i am getting a issue with clients which are connected to the wireless AP, they are not able to get an dhcp IP address from the 2960 Switch (DHCP Server). The clients are getting IP address as 0.0.0.0. [code]
View 36 Replies
View Related
Jun 17, 2012
Our company has 8 4404-100 Cisco wireless controllers and each WLC has 8 W LANs configured. They are all working fine. However, the WLAN ID sequence is not consistent. I'm wondering if it's possible to change the WLAN ID on these WLCs without (or slightly) impacting the users. I don't want to re-configure all the WLAN profiles.
View 13 Replies
View Related
Oct 9, 2011
what seems to be a common issue/query regarding getting AppleTV to work via the Wireless Lan Controller.We are running WCS 7.0.172.0, our WISM controllers are on software version 7.0.116.0 and our APs are a mixture of 1140 and 1142s with both 11a/n and 11b/g enabled.
What we are finding is that we are able to stream to the AppleTV box when connected to the LAN and both devices are on the same subnet.however, as soon as we go onto the WLAN ( both devices on the same subnet ) , the end device can no longer see the AppleTV box to stream too.
[code]...
View 7 Replies
View Related
Feb 27, 2011
Just bought two new LAP1041N APs to add to a dead spot on our campus. Well when trying to set them up the will not stay connected to the WLAN Controller (model 4402). The new APs boot fine, and will even appear in the controller for brief moments, but after a few seconds they dissapear and start showing the discovery status light pattern (green, red, amber). Just wondering if I am doing something wrong with these APs, or what the issue could possible be.We have 10 other APs that as soon as we connected to network were detected by controller and we configured from there. Most of those are 1010 or 1020s, we have a few 1131s and 1100s.
View 7 Replies
View Related
May 29, 2012
I will migrate a Cisco WLAN Controller 2125 to 2504,So I have one question?I need to make all configuration into the new Wlan Controller or I can migrate with one tool or something else?
View 15 Replies
View Related
Aug 3, 2011
we use wlc 4402 (Software Version 7.0.98.0) and want to allow only several wlan nic vendors to connect to a wlan ssid.According to this, is it possible to configure MAC Filtering with wildcards, e.g. aa:bb:cc:* ?
View 1 Replies
View Related
Apr 23, 2012
I have a 2504 and my goal is to automatically redirect a users home page when they connect to a certain internal website. Authentication isn't a real concern just now.
Is it possible to simply have a users home page redirected when they open their browser upon connecting to the SSID? All of the documents available have stated to use 802.1x / RADIUS or other fancy tools.
View 3 Replies
View Related
