Cisco Wireless :: Set Aironet 1232AG-A-K9 As Repeater While Using 4402 Controller

Oct 8, 2012

Is it possible to set an Aironet 1232AG-A-K9 as a repeater while still using a 4402 controller?  I have some wireless security cameras in our parking lots that I need to extend wireless to and I have a handful of 1232 points that I am not using.  I have some omni antennas and a yagi directional that I was planning on using.Everything I am reading talks about configuring the AP while in automous mode, not while running the lightweight image.

View 2 Replies


ADVERTISEMENT

Cisco Wireless :: Configuring 1232AG As Repeater

May 26, 2011

I have a Cisco Aironet 1130 Series setup as a Root AP and a Cisco Aironet 1200 Series Access Point setup as a Repeater. However i cannot get this to work. I can connect fine to the Root AP but not to the Repeater.
 
I receive the folloiwng error on the Repeater AP.
 
'*Mar  1 00:00:24.887: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response'
 
The Root access point is connected to a Cisco router (192.168.168.1) which is the gateway to outside and is also acting as a dhcp server.
 
Both SSID's and  authentication/encryption match.
 
Im using the the below mac-address for Authenticating the Repeater to the Root with the parent 1  command. Should i be using the mac address of dot11radio 0 of the Root AP??
 
AP_Root#sh interfaces dot11Radio 0Dot11Radio0 is up, line protocol is up  Hardware is 802.11G Radio, address is 001b.2b69.6ca0 (bia 001b.2b69.6ca0)  MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,     reliability 255/255, txload 1/255, rxload 1/255

View 5 Replies View Related

Repeater / Wireless Extender For Cisco Aironet 1041?

Nov 16, 2012

I have a Cisco Aironet 1041 , what a good repeater/wireless extender that works with it to cover an area of 50 squared meters ?

View 4 Replies View Related

Cisco Wireless :: Setting Up Aironet 1142n As Repeater?

Aug 9, 2012

I've just recently purchased the Aironet 1142n and am hoping to set it up as a repeater. I've followed the documentation here: [UEL] but am still having problems.
 
What I'm trying to achieve is: I have an adsl router (TP-link W8960N) at the front of the house but the wireless signal does not reach all the way to the end of the house. I am trying to set up the aironet 1142n to act as a repeater and place it in the middle of the house and hopefully that will extend the wireless signal to the end of the house and remove the dead spots. I would like to do this without having ethernet cables running all over the place and have been trying to configure the aironet 1142n to no avail. Every time I set the aironet 1142n to "repeater" it automatically coverts back to "access point" under role of radio network.
 
I guess my main question first of all is, can I set the aironet 1142n as a wireless repeater? And if so, where am I going wrong in my configuration?
 
I've just read that " Repeater access points running Cisco IOS software cannot associate to parent access points that that do not run Cisco IOS software."
 
Does this mean the aironet 1142n set up as a repeater will not work if the original access point (in this case, the TP Link adsl wireless router) isn't a cisco brand?

View 3 Replies View Related

Cisco Wireless :: Can The Aironet 1310 Setup As A Repeater

Jul 10, 2012

Can the Aironet 1310 setup as a repeater? I could not make the AP as the repeater associated to another 1310 ap. This AP is running LADAP.

View 11 Replies View Related

Cisco Wireless :: Connecting WET200 To Wi-Fi Controller 4402

Jun 30, 2010

We Have a WLC-4402 controller with LWAPPs and different VLANs and SSIDs. I've configured a Linksys WET200 to associate to one of the SSIDs.On the WLC I can see, that the WET200 is associated to one Wlan.Then I connect one computer with a static IP address and works fine.But when I connect a second one, everythiing goes down. It does not connect.I can only connect one computer to the WET200.Do I need other seetings on the WLC to allow pass traffic through the WET200?

View 4 Replies View Related

Cisco Wireless :: Password Recovery LAN Controller 4402?

Jul 20, 2008

how to password recovery Wireless LAN Controller 4402

View 3 Replies View Related

Cisco Wireless :: 5508 And 4402 Controller Anchoring?

Mar 11, 2012

I am running 5508 wireless controllers. I pass along another agency's WLAN across my wireless network that is anchored to their older 4402 controller.
 
I wish to run the new 3600 series APs and am planning on migrating to NCS and the new 7.2 code.
 
I know that the older 4400 series controllers will not handle the newer 7.1 or 7.2 code. However, i still wish to maintain this anchor relatiosnhip with the older 4402 controller. I need to know if this will work or not.

View 2 Replies View Related

Cisco Wireless :: AP LAP1142N Can't Join Controller - 4402

Apr 11, 2012

1) AP was originally running a standalone image.  I booted it into a so-called ROMMON or AP mode (ESC is the right key to make it boot into this mode).

I found a recovery image in its flash - c1140-rcvk9w8-mx. I made the AP boot from it by using "set" command and I see that it start booting using this recovery image. Here goes the question. Do all AP settings matter ? E.g. when I run "set" command from AP I see the following:
 
ap: set
?=
DEFAULT_ROUTER=10.0.0.1
Default_router=10.9.99.1
ENABLE_BREAK=yes

[Code].....

View 27 Replies View Related

Cisco Wireless :: Replace 4402 With 5508 Controller

Oct 6, 2012

I'd like to replace my 4402 Wireless controller with a new 5508. I have migrated the exact configuration from my 4404 controller to the 5508 and they are both running the same version of code. I'm worried that if I replace the 4402 with the 5508 controller, the Access Points will not rejoin to the new controller or they will join but will have lost their configuration e.g. AP Name/location etc etc. AP models registered to the existing controller are 1131, 1142 and 3502. I am also using Cisco WCS.
 
As long as the new controller has the exact same configuration, is it possible to replace the 4404 with the 5508? Will the existing Access Points join the new controller? Is there any other configuration required? I have read about doing this using mobility groups however would rather not if possible.

View 2 Replies View Related

Cisco :: Wireless Controller 4402 - Printing Setting Via Wi-Fi?

Oct 16, 2012

I have a wireless printer on an internal wireless network.  I have a laptop connected wirelessly on the same internal network.  When both devices are connected to the same network I cannot connect to the printer.  If I change my laptop over to the guest wireless or to a wired lan, I can see the printer.  I vendor stated that within the 4402 wireless controller there is a setting to allow wifi to wifi connections on the same internal network.  I am trying to figure out what that setting is called and where I might look for the setting within the wireless controller.

View 1 Replies View Related

Cisco Wireless :: LAN Controller 4402-12K9 Upgrade To 25 APs

Jan 27, 2013

I have a 4402-12-k9 controller and I need to upgrade to 25 APs Can I buy a 12 or 25 license upgrade to this controller?

View 7 Replies View Related

Cisco Wireless :: 4402 And 5508 Controller Installation

Oct 30, 2012

My client has on cisco 4402 controller running with 48 AP on this. Client requires to add another 25 AP but licence on the current controller is not supported client bought another controller 5508 with 25 AP.
 
I have been tasked to installe 5508 with conjestion of 4402. I have make the software version on both of them as below
 
AIR-CT5500-K9-7-0-235-3.aes
AIR-WLC4400-K9-7-0-235-3.aes
 
To match the same IOS version on both the controller. I have following challenges with me.
 
- 5508 will registered 25 AP while .. 4408 will continue with 48 AP.
- 5508 is going to be in DC and it will be directly connected to firewall as default gateway for guest SSID. 4402 is going to be on another building.
- How can I make sure that Users connected to AP registered with 4402 will have the same deafult gateway as 5508. Thre is no layer 2 connectivity between this two controllers.
- There is no romaing going to happen between this two controller as both are two different locations and user will leave one location will disconnect and it joines bak when it reach to another controller.
- Is there any way to configure 5508 as master and 4402 as slave kind of connections?

View 1 Replies View Related

Cisco Wireless :: Aironet 1140s - How To Connect Repeater To Specific Access Point

Feb 12, 2013

In our office, we have 3 Cisco Aironet 1140s and they are configured as follows: 

* Access Point A (192.168.0.50)
* Access Point B (192.168.0.51)
* Repeater (192.168.0.49)
* SSID : 101
 
how to have the Repeater connect to Access Point A only?

View 3 Replies View Related

Cisco Wireless :: AP 1131 AG Do Not Associate To Controller 5508 Or 4402

Apr 18, 2013

I have 10 Access-Point model 1131 AG are new AP.
 
When I connect the access-Point to the network, the AP associate only one time but i go to wireless for see the AP, i can see downloading of IOS, but the ios is 3.0.59, the ap don not nothing. I can not change any parameters.

View 4 Replies View Related

Cisco Wireless :: How To Modify RADIUS Servers On 4402 Controller

Jul 20, 2010

I have several controllers, including a 4402 running 6.0.188.0 software and I need to modify the Radius servers that it uses. Currently I have three servers listed;

1 - 10.246.194.16
2 - 10.200.31.78
3 - 10.247.50.56
 
I would like to delete server 1 which is being retired and replace it with a new server 1. I suspect, once i get servwe 1 deleted, the server 1 option would become available when I create a new server. I went into the controller and disabled server one, but every time I try and delete it, I get the "Server in use either on a specific WLAN or Mesh Radius Server Configuration" error. I can't find anywhere this server is still in service and being used, either by a WLAN or a Mesh. I've tried several different variances to modify this. What I hope to avoid is the need to reset the controller. I have a total of seven controllers that I need to make this modification to, and It will be ugly if I have to reboot these units. Hospital mission critical stuff.

View 4 Replies View Related

Cisco Wireless :: Unable To Upgrade Lan Controller 4402 Firmware

Mar 1, 2012

I am in the midst of trying to update the controller firmware of a cisco wireless lan contoller 4402, and having some issues getting the file to transfer to the controller.  i am currently running verison 5.0.148 on the controller and attempting to upgrade to the latest version of 7.0.230  and for whatever reason it continues to not transfer. I have tried all 3 methods of cli, gui and using wcs software. all the no avail , I have tried tftp32 and 3cdaemon with the same results.
 
The error that i am getting from 3cdaemon is got socket timeout aborting code 10054, failing at 66MB transfered. I increased the timeouts both on the wlc and  the tftp client to no avail
 
the error i get on the wlc is Code file transfer failed - Error while writing output file

View 5 Replies View Related

Cisco Wireless :: 4402 Controller - Client Reauthenticates Occasionally

Mar 15, 2013

I have 3 WLC 4402 controller connected to an ACS Server and Cisco 1252G AP. Previously the wireless networks works fine but for two weeks now most of the clients experiencing reauthentication frequently, Some experience it every 5 mins even if they are browsing or idle and not moving. I've check the session time out settings in the wlc and it was configured for 30 mins as default. I have around 900 student clients connecting every day.

View 4 Replies View Related

Cisco Wireless :: Internal DHCP Server On 4402 Controller

Apr 8, 2008

I am trying to setup a guest vlan. I set up an interface for the guest vlan on my 4402 controller. I assigned the guest vlan interface an IP of 192.168.2.10 with a 24 bit subnet mask.
 
This vlan will go to my DMZ where there is no DHCP server so I need to setup the internal DHCP server. I created a new scope but I'm having trouble with what to put in the Network field for the DHCP scope. The pool addresses are 192.168.2.100-200. with a 24 bit subnet mask.
 
Every time I try to apply the configuration I get an "error in  setting DHCP scope network and netmask".
 
I've tried using:
 
192.168.2.10
192.168.2.255
192.168.2.254
 
as entries for the Network setting but no go. The docs say to enter the IP address used by the management interface with subnet mask applied.
 
I was assuming they meant the interface for the guest vlan.

View 3 Replies View Related

Cisco Wireless :: How To Use Mac Filtering With Wildcards On 4402 Wlan Controller

Aug 3, 2011

we use wlc 4402 (Software Version  7.0.98.0) and want to allow only several wlan nic vendors to connect to a wlan ssid.According to this, is it possible to configure MAC Filtering with wildcards, e.g. aa:bb:cc:* ?

View 1 Replies View Related

Cisco Wireless :: Software Version Upgrade For 4402 LAN Controller

Jun 5, 2012

We have Cisco 4402 Wireless Lan Controller with Software Version 3.2.171.6 and we want to upgrade it to latest version.
 
What is the latest version to upgrade the WLC?
 
Also since WLC is running on very lower version is it possible to upgrade to the latest version directly or we have to move it step by step to upgrade this to latest version?

View 3 Replies View Related

Cisco Wireless :: 4402 - Controller Crashed With Reaper Reset

Jan 17, 2012

We have upgraded to latest IOS but observed this box is hitting a bug which was resolved in the earlier releases but not seen in 4402.
 
Is this related to hardware issue or a software bug only.
 
CSCtg94715
CSCtk83586
CSCso90721
 
Error!  Software watchdog on task dot11b expired! Reaper Reset: Task "dot11b" missed software watchdogError!  Software watchdog on task apfMsConnTask_0 expired! Reaper Reset: Task "apfMsConnTask_0" missed software watchdogError!  Software watchdog on task apfReceiveTask expired! Reaper Reset: Task "apfReceiveTask" missed software watchdogError!  Software watchdog on task radiusTransportThread expired! Reaper Reset: Task "radiusTransportThread" missed software watchdogError!  Software watchdog on task ccxL2RoamTask expired! Reaper Reset: Task "ccxL2RoamTask" missed software watchdogError!  Software watchdog on task dot1xMsgTask expired! Reaper Reset: Task "dot1xMsgTask" missed software watchdogError!  Software watchdog on task spamReceiveTask expired! Reaper Reset: Task "spamReceiveTask" missed software watchdogError!  Software watchdog on task dtlArpTask expired! Reaper Reset: Task "dtlArpTask" missed software watchdogReaper is kickin' into high gear  Task dtlArpTask is consuming 0% CPU! (0% user, 0% system)  Frame 0: 0x10004708: sighup_handler+84
  
************************************************************
*             Start Cisco Crash Handler Serv               *
************************************************************
Sys Name:           HJ_Wireless_Controller
Model:              AIR-WLC4402-50-K9

[code].....

View 2 Replies View Related

Cisco Wireless :: 4402 Guest Anchor Controller 5508 Software 7.2

Nov 6, 2012

We currently have all of our foreign AP controllers on software version 7.0.116.  This consists of a mixture of 4400 and 5508 WLC's.  Our guest anchor is a 4402 on version 7.0.116.  We are replacing the guest anchor with a 5508.  We are also upgrading our 5508 wireless controllers to version 7.2 to support the 3600 series AP's.  My question is what is the recommeded code that the anchor controller should be on?  Should it also be upgraded to 7.2?  If we upgrade the anchor controller to version 7.2, will this affect anchoring to 4400 series foreign controllers still on7.0.116?                 

View 9 Replies View Related

Cisco Wireless :: 4402 WLC Management / Local Controller Versus Cloud

Feb 26, 2013

We are currently looking to upgrade (re-design) our wireless network at our college. Any experience going from a local, controller-based wireless network to a cloud-based controller? If so, what have you found the pros and cons to be?
 
If you thought about going to a “cloud solution”, what stopped you?
 
We are currently running wireless at our 3 primary campus locations, and looking to add it to our 3 satellite locations. We use 4402 WLCs at our primary locations with a mix of 1140 and 1240 APs.

View 5 Replies View Related

Cisco Wireless :: Can 2 Aironet 1042 Use WDS Without Controller?

Sep 20, 2012

Can 2 Aironet 1042's using WDS handoff a session between them without any other network hardware needed?

View 1 Replies View Related

Cisco Wireless :: Aironet 3500 LAP Without Controller?

May 4, 2012

We have couple of Cisco Aironet 3500 Series access points with the following P/N: "AIR-CAP3501E-A-K9", we have discovered that we need a wireless LAN controller to connect those new access points!, however, we do not have any wireless controller in our LAN.
 
We even tried to CLI through the console port but we could not set any static IP on it!, after reading on Cisco site we discover that this type of AP is called "Lightweight Access Point" LAP which handles all the management tasks to the controller!
 
So what shall we do! is it impossible to operate them without the controller?

View 6 Replies View Related

Cisco Wireless :: 5508 - Configuring Repeater To Wlan Controller?

Jan 1, 2013

I have Cisco 5508 Wlan Controller Software version 7.2.103.0 and I have Cisco AIR-CAP3602I-E-K9 Lightweight Access Points network and its working fine now I want to configure the Repeater in this network.  Because there is one area we cannot layout the cable.  How to add the repeater and how to configure the repeater in wlan controller network.
 
Do i need the change the software of Wlan Controller to support Mesh Network or this version 7.2.103.0 can support the repeater because for 1 access point i dont want to upgrade the version.

View 22 Replies View Related

Cisco Wireless :: 4402 Access Points Without Wireless LAN Controller

May 8, 2012

I have cisco 4402 Wireless LAN Controller with Cisco Access Point (AIR-LAP1252G-E-K9), everything is running smoothly.How come i use my Access Points without Wireless LAN Controller, is there any possibility then which AP model would be suitable?

View 2 Replies View Related

Cisco Wireless :: 1142 Aironet Won't Join Controller

Aug 6, 2012

When I check the AP join statistics I  see the following: Reason For Last Unsuccessful Attempt    RADIUS authorization is pending for the AP, I don't run a radius server and don't know how to get around this so that the device can join.

View 4 Replies View Related

Cisco Wireless :: Aironet 3602I Is Stand Alone Or Need A Controller?

Apr 8, 2012

Cisco Aironet 3602I  is stand alone or need a controller ?

View 8 Replies View Related

Cisco Wireless :: Aironet 1230 Cannot Join Controller

May 7, 2012

my access point 1230 fail to join the controller. The image is C1200-k9w7-mx.123-8.JA2. I tried to reboot it but it does not join to controller. How do I initiate the discovery process again to make this AP to join? Should I convert it back to autonomous AP and then LWAPP process again? I can ping the AP from the controller and the AP is in the same VLAN with controller.

View 3 Replies View Related

Cisco Wireless :: Can Connect Various Aironet 1242 To 2500 Controller

Dec 5, 2012

Can I connect various Aironet 1242 to Wireless controller 2500?

View 4 Replies View Related

Cisco Wireless :: Setting Up Aironet 2600 APs With 2504 Controller

Mar 19, 2013

I've recently purchased a 2504 Wireless controller, and I have 10 2600 APs to deploy.  I think I've set up the wireless controller OK - there doesn't seem to be much that needs to be done!  But I just can't seem to register an AP onto the system.

Just to briefly outline what I have done, I have connected to the Wireless Controller via terminal emulator and run through the setup, then I have connected OK to the web interface, and I am able to view and amend the controller's configuration.  So I have setup a WLAN and thats about it.

Next up I have powered on one of my 2600 APs, and I am able to view it working via terminal emulator again.  But I am seeing it continually running the same routine to connect to a controller, and all the time it just fails.  Below is what I am seeing.
 
One thing that I am unsure about is that I am unable to connect to the AP config pages via web browser, using the IP 192.168.0.97 (although it does ping okay).  Is that odd?
 
And the main question - why doesn't the AP connect to the wireless controller?  Do the APs need to be authroized on the controller first?  If I check the controller's web interface, under Monitor - Statistics - AP Join, I can see the AP listed with Status "Not Joined" but I don't know what I need to do to make it join!
 
*Mar  1 02:28:54.579: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.*Mar  1 02:28:57.583: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.*Mar  1 02:28:57.651: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.0.97, mask 255.255.255.0, hostname APb0fa.eb56.5abf(code)

View 12 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved