Cisco Wireless :: Can 2 Aironet 1042 Use WDS Without Controller?

Sep 20, 2012

Can 2 Aironet 1042's using WDS handoff a session between them without any other network hardware needed?

View 1 Replies


ADVERTISEMENT

Cisco :: Aironet 1042 Wireless N Not Broadcasting?

Nov 27, 2011

I have an Aironet 1042 wireless AP if I create an SSID with no security it shows up as wireless N when I see it on a windows 7 laptop.  As soon as I apply any security settings is shows up as G and not N.  I just want to be able to authenticate with a Windows 2008 server running NPS - this works fine but I obviously want to connect at N speed and not G.

View 13 Replies View Related

Cisco Wireless :: WDS On Aironet 1042 Autonomous AP?

Jul 11, 2012

i'm trying to enable WDS with authentication on a Cisco 1042 AP. The unit itself will be the WDS master and Radius server as well it will serve clients (not that many). The AP is running version 12.4(25d).After multiple tries of configurating, I keep getting the same issue: as soon as I connect to the SSID, I can enter the username and password but authentication fails - hence the message in my console: 

%DOT11-7-AUTH_FAILED: Station xxxx.xxxx.xxxx Authentication failed. Every configuration I made was started from factory defaults of the AP.My current tests are with one AP only and if tests go successfully, I will add more infrastructure AP's to the setup.

hostname WDS_SERVER!logging rate-limit console 9enable secret 5 $1$FcRQ$T5MglV/0ybzKEfk3DoN/J0!aaa new-model!!aaa group server radius InfraAP server 192.168.28.34 auth-port 1812 acct-port 1813!aaa group server radius Clients server 192.168.28.34 auth-port 1812 acct-port 1813!aaa authentication login APlist group InfraAPaaa authentication login WirelessClients group Clients!aaa session-id common!dot11 ssid Test   authentication open eap WirelessClients   authentication key-management wpa version 2 cckm   guest-mode!username Cisco password 7 14341B180F0B!bridge irb!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid Test ! antenna gain 0 station-role root bridge-group 1 bridge-group 1

[code]....
 
I've tried the configuration from the Cisco config guide as well but without any luck [URL]

View 5 Replies View Related

Cisco Wireless :: 2504 - 1042 AP Registration With Controller

Jul 21, 2012

I ordered controller 2504 and will arrive soon. I want to know that after configure the initial setup of 2504 (i.e. AP manager , Management IPs etc) and defining the DHCP for AP. Will the 1042 lightweight AP will register with the controller automatically or i need to manually define the AP (MAC address) on WLC. and also whether the Option 43 and 60 are correctly defined?
 
Management Interface: 10.10.22.15
AP Manager Int: 10.10.22.16 
ip dhcp pool WLAN103
network 10.10.3.0 255.255.255.0
[code]...

View 4 Replies View Related

Cisco :: Unable To Join Wireless AP 1042 With 2106 Controller?

Nov 29, 2012

I am not able to join 1042 wireless AP with 2106 controller, even i mention that controller ip is 192.168.200.5 it try to join with controller on 192.168.200.6 ip address always. following are the error logs i can see on console. 
 
*Nov 30 19:50:20.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:20.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Nov 30 19:50:21.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:21.436: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.200.6
*Nov 30 19:50:21.436: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

[code]....

View 4 Replies View Related

Cisco Wireless :: 1042 LAP With 5508 Series Controller - AP Will Not Associate

Jun 11, 2012

I have a 5508 WLC licensed for 100 APs.  I have 1 - 1042 LAP connected for testing.  I have DHCP configured for the AP, and it gets an address of 192.168.254.100/24 - the controller's management interface is 192.168.254.99/24.  I can see that the AP is getting an IP and I can ping it from the controller.  However, I simply do not see the AP associating.  I enabled capwap debiugging and watched the events, but I didn't see anything crazy that clued me in.  What am I doing wrong?
 
The controller is v6.0.199.4
 
Every time I have set these up in the past they have been pretty straight forward.  I haven't gotten too deep into the config on the WLC becuase I don't want to cause more issues.

View 2 Replies View Related

Cisco Wireless :: Aironet 3500 LAP Without Controller?

May 4, 2012

We have couple of Cisco Aironet 3500 Series access points with the following P/N: "AIR-CAP3501E-A-K9", we have discovered that we need a wireless LAN controller to connect those new access points!, however, we do not have any wireless controller in our LAN.
 
We even tried to CLI through the console port but we could not set any static IP on it!, after reading on Cisco site we discover that this type of AP is called "Lightweight Access Point" LAP which handles all the management tasks to the controller!
 
So what shall we do! is it impossible to operate them without the controller?

View 6 Replies View Related

Cisco Wireless :: 1142 Aironet Won't Join Controller

Aug 6, 2012

When I check the AP join statistics I  see the following: Reason For Last Unsuccessful Attempt    RADIUS authorization is pending for the AP, I don't run a radius server and don't know how to get around this so that the device can join.

View 4 Replies View Related

Cisco Wireless :: Aironet 3602I Is Stand Alone Or Need A Controller?

Apr 8, 2012

Cisco Aironet 3602I  is stand alone or need a controller ?

View 8 Replies View Related

Cisco Wireless :: Aironet 1230 Cannot Join Controller

May 7, 2012

my access point 1230 fail to join the controller. The image is C1200-k9w7-mx.123-8.JA2. I tried to reboot it but it does not join to controller. How do I initiate the discovery process again to make this AP to join? Should I convert it back to autonomous AP and then LWAPP process again? I can ping the AP from the controller and the AP is in the same VLAN with controller.

View 3 Replies View Related

Cisco Wireless :: Set Aironet 1232AG-A-K9 As Repeater While Using 4402 Controller

Oct 8, 2012

Is it possible to set an Aironet 1232AG-A-K9 as a repeater while still using a 4402 controller?  I have some wireless security cameras in our parking lots that I need to extend wireless to and I have a handful of 1232 points that I am not using.  I have some omni antennas and a yagi directional that I was planning on using.Everything I am reading talks about configuring the AP while in automous mode, not while running the lightweight image.

View 2 Replies View Related

Cisco Wireless :: Can Connect Various Aironet 1242 To 2500 Controller

Dec 5, 2012

Can I connect various Aironet 1242 to Wireless controller 2500?

View 4 Replies View Related

Cisco Wireless :: Setting Up Aironet 2600 APs With 2504 Controller

Mar 19, 2013

I've recently purchased a 2504 Wireless controller, and I have 10 2600 APs to deploy.  I think I've set up the wireless controller OK - there doesn't seem to be much that needs to be done!  But I just can't seem to register an AP onto the system.

Just to briefly outline what I have done, I have connected to the Wireless Controller via terminal emulator and run through the setup, then I have connected OK to the web interface, and I am able to view and amend the controller's configuration.  So I have setup a WLAN and thats about it.

Next up I have powered on one of my 2600 APs, and I am able to view it working via terminal emulator again.  But I am seeing it continually running the same routine to connect to a controller, and all the time it just fails.  Below is what I am seeing.
 
One thing that I am unsure about is that I am unable to connect to the AP config pages via web browser, using the IP 192.168.0.97 (although it does ping okay).  Is that odd?
 
And the main question - why doesn't the AP connect to the wireless controller?  Do the APs need to be authroized on the controller first?  If I check the controller's web interface, under Monitor - Statistics - AP Join, I can see the AP listed with Status "Not Joined" but I don't know what I need to do to make it join!
 
*Mar  1 02:28:54.579: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.*Mar  1 02:28:57.583: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.*Mar  1 02:28:57.651: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.0.97, mask 255.255.255.0, hostname APb0fa.eb56.5abf(code)

View 12 Replies View Related

Cisco Wireless :: Aironet 1260 Access Point Work Without Controller??

Dec 1, 2010

I would like to buy Cisco  Aironet 1260 Access Points, i just want to use them independantly so   i want to know do they work without the Wireless LAN Controller? or i  have to have the controller for them to work? they will be in different locations so i cant have a controller per each location.

View 9 Replies View Related

Cisco Wireless :: 2504 Controller With 3 Aironet 1142 Access Points

Mar 16, 2013

I have installed/setup a cisco 2504 wireless controller and 3 aironet 1142 access points using the basic config on a windows sbs 2008 domain, the problem is that the clients that are connected to the 2504 aint getting the there ip addr from the AD but from the wireless controller, and there cant reach the clients on wifi from the clients that are connected to lan, is there anyway that i cant change this so that a client on lan can see the client on wlan and vice versa.

View 5 Replies View Related

Cisco Wireless :: Configure Multiple SSID On Aironet 3600i AP Via 2504 Controller

Apr 3, 2012

Can I configure Multiple SSID (Guest/Corporative) on Cisco Aironet 3600i AP via Cisco 2504 Wireless controller?

View 1 Replies View Related

Cisco :: Configure Aironet 3500i Without WLC Controller?

Nov 30, 2011

if i can configure the cisco aironet 3500i without WLC controller.

View 1 Replies View Related

Cisco Wireless :: Controller 4400 Series Work With Aironet 3600 Series

Mar 6, 2012

Can Controller 4400 series work with Aironet 3600 series?

View 5 Replies View Related

Cisco Wireless :: 1522 MAP Through 1042 RAP Not Working?

Mar 25, 2012

I'm trying to mesh a 1522 MAP through a 1042 RAP but this doen´t work. I get strange messages on the trap log:
 
1 Mon Mar 26 18:40:19 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. .. .
3 Mon Mar 26 18:37:13 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:10'. 4 Mon Mar 26 18:34:00 2012 Mesh node 'f0:25:72:d9:69:6f' has changed its parent 5 times in last one hour.
5 Mon Mar 26 18:34:00 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. 6 Mon Mar 26 18:33:44 2012 Mesh child node 'f0:25:72:d9:69:6f' is no longer associated with mesh node '58:35:d9:c6:60:10'.

[code]....

If i debug the 1042 i also see "... has 1 AES-CCMP TSC replays messages..."I have some 1522 MAP meshing through 1142 working fine on same 5508 controller version, i think there are few differences between 1042 an 1142.

View 1 Replies View Related

Cisco Wireless :: WLC 2112 With 1042 Mesh APs?

May 16, 2013

I have a Mesh architecture with 2112 WLC and 1042 APs I want just to know if I can connect one 1310 AP to the ethernet port of a mesh 1042 AP with ethernet bridging enabled.

View 4 Replies View Related

Cisco Wireless :: 2504 WLC / 1042 AP - Client Not Connecting

May 21, 2013

2504 WLC, 1042 AP's
 
I have my NPS server setup, Group Policy, Certs (RAS+IAS), DHCP option 43, DNS A record
 
If I look in the event viewer on NPS, it says
 
Log Name:  Security Source: Microsoft- Windows -Security -Auditing Date:  5/22/2013 12:36:37 PM
Event ID: 6272Task Category: Network Policy Server Level: Information Keywords: Audit Success User: N/A Computer:      mfs1.Mitchell. internal Description:Network Policy Server granted access to a user.
[Code] .....
 
But the laptop won't connect or get an IP.

View 30 Replies View Related

Cisco Wireless :: Power Local Settings On 1042?

Dec 14, 2011

What dbm or mw each of the power local settings are? I see on a 1042 from -1 thru 20 and am assuming 20dBm is 100mW.
 
OM-ess-lab-WLAN1(config-if)#power local ?

<-1 - 20>  One of : -1 2 5 8 11 14 17 20  maximum    Set power to allowed maximum

View 6 Replies View Related

Cisco Wireless :: Do 1042 Autonomous APs Support GRE Tunnels

Jan 24, 2013

Do the 1042 Autonomous APs support GRE tunnels?

View 4 Replies View Related

Cisco Wireless :: 1042 - New AP Not Showing In Default Group?

Apr 25, 2013

I got a new 1042 AP and connected it to the network. I have a 2504 contrller with 6 AP's already on it. I thought I could just plu in the new AP and it would show up in the AP group. Instead it shows up as a rouge AP. How do i get the new AP to show up in the default group?

View 24 Replies View Related

Cisco Wireless :: Captive Portal On AP 1041 / 1042

Sep 18, 2012

There is WLAN with Nortel APs witha captive portal. We are migrating to a Cisco Solution and we have AP 1041 / 1042
 
How can I configure Captive Portal in the 1041/1042 APs

View 3 Replies View Related

Cisco Wireless :: Power Requirements For 1042 Mesh Network

Apr 8, 2012

this note is from the 5508 controller config manual, does this apply to 1040 access points in a mesh network? 
 
Note:The recommended power source for MAPs is either a power supply or power injector. PoE is not a recommended power source for MAPs.

View 2 Replies View Related

Cisco Wireless :: Capability To Downgrade AP 1042 From CAPWAP To Autonomous?

Jan 6, 2011

I would like to confirm if it is possible to downgrade AP 1042 from CAPWAP to autonomous? I want to buy the AP model AIR-LAP1042N-A-K9. But i don't sure if in the future it could support this feature.

View 9 Replies View Related

Cisco Wireless :: 1042 Autonomous AP - BSSID Failed Authentication

Feb 13, 2013

I am trying to configure a Cisco 1042 autonomous AP and have ran into some problems. I require 2 broadcasted SSIDs that use WPA v2. When I only have 1 of the SSIDs enabled, I can authenticate with no problems. When I have both SSIDs enabled, I can connect to one of the networks, but not the other. I have verified the PSK multiple times, but the logs still show  dot11-7-auth_failed. If I remove the working SSID and make no changes to the SSID for which authentication previously fails, everything works fine. Upon adding the other SSID back, I run into the same authentication issue.

View 3 Replies View Related

Cisco Wireless :: Implement 2504 WLC And 1042 Access Points?

Mar 1, 2013

We have purchased Cisco 2504 Wireless Controller (One) and Ciscon 1042 Access Points (Five). At present I am going to use 3 access points only.I have attached a simple diagram of our office network. We have more than 30 VLANs configured in Core Switch, we are planning to give wifi access to only 3 VLANs.
 
1. VLAN 121 ( IP Segment - 10.52.121.0 /24)
2. VLAN 116 ( IP Segment - 10.52.116.0 /24)
3. VLAN 100 ( IP Segment - 192.168.100.0 /24) (Guest)

I would like to use LDAP or ACS for authentication purpose.

View 3 Replies View Related

Cisco Wireless :: Access Point Coverage Area 1042

Apr 6, 2012

I want buy an Access point which cover 300 Meter coverage Area.
 
Have any data sheet or link where I can found which AP coverage how many Area, Like 1042 Access Point cover how many Feet Space.

View 8 Replies View Related

Cisco Wireless :: 1041 / 1042 - Apple Ipad Intermittent Wi-Fi Connectivity?

May 3, 2012

We are experiencing problems with Apple Ipads on a large scale network that we install and maintain, the Ipads seem to join the network with no problems (bit slower than laptops etc) but will then disconnect for no apparent reason at random intervals.  We have ran laptops on the same AP's and in the same area and no similar probems occurred, we are using IOS Cisco 1041's and 1042's, we have seen one of the Ipads's sitting quite happily on a 1042 2,4ghz radio and then it disconnected and went to the 5ghz radio.  We are getting similar disconnects on the single radio 1041.

View 13 Replies View Related

Cisco Wireless :: 2.4 / 5Ghz Load Balancing Utilize On Both 1042 And 1252

Oct 25, 2012

In my class room, a lot of new Dell notebook (university purchased) all of those are the same model. Those came with 2.4&5Ghz WLAN NIC.
 
So, my WLC-based AP in that room which is Cisco 1x1042 & 1x1252 running in light-weight.This make huge congest on 5 Ghz. All of my 41 NB go for 5Hgz. And Zero client on 2.4Ghz radio, 2.4Ghz is not utilized at all.
 
I have read a lot of those related discussion. But I even can not find one that need to utilized BOTH of band. Most of those discussion talking to band-select which is "this feature only goes in one direction from the 2.4 GHz range to the 5 GHz not visa-versa."
 
My constrint is We can not touch the NB. Because this is university, much many diverse user loging in.

View 7 Replies View Related

Cisco Wireless :: 1042 - Convert Light Weight AP To Autonomous Mode?

Mar 19, 2012

I have 1042 Light weight AP and i want to convert it to Autonomous mode . i dont find any particular image for this conversion ..when i try to find autonomous image for 1040 its showing "c1140-k9w7-tar.124-25d.JA1.tar"........can i use this image ?...

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved