my access point 1230 fail to join the controller. The image is C1200-k9w7-mx.123-8.JA2. I tried to reboot it but it does not join to controller. How do I initiate the discovery process again to make this AP to join? Should I convert it back to autonomous AP and then LWAPP process again? I can ping the AP from the controller and the AP is in the same VLAN with controller.
View 3 RepliesWhen I check the AP join statistics I see the following: Reason For Last Unsuccessful Attempt RADIUS authorization is pending for the AP, I don't run a radius server and don't know how to get around this so that the device can join.
View 4 Replies View RelatedI have the problem that the AP1130 can not join to WLC2504.
Console Messages of AP1130:
*Aug 14 09:34:54.029: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 14 09:34:54.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.x.251 peer_port: 5246
[Code].....
upgrading 300 Aironet 1100 series i.e. 1121 to newly bought WLC.Problem is 1100 are using SSC cert that I must do " debug pm pki enable " on each of 300 AP upgrading to extract its key-hash then copy to Security>AAA>AP Policy and repeat for 300 times. It is the impossible task.What would you recommend us to do the any other methods to achive the same goal?
View 2 Replies View Relatedi converted the C1310 to LAP using upgrade tool. but the AP is not able to join the controller i was not able to view SHA Key in upgrade tool, so i ran the "debug pm pki enable " on the controler to get it. i'm still not able to view SHA key.
here is the output of debug command
*spamApTask0: May 21 15:07:43.527: 88:43:e1:d1:fc:9e Received LWAPP JOIN REQUEST from AP 88:43:e1:d1:fc:9e to cc:ef:48:b3:23:ef on port '13'
*spamApTask0: May 21 15:07:43.549: sshpmGetIssuerHandles: locking ca cert table
[Code].....
Network environment: (well configured and working fine)
2 AIR-WLC2106-K9 - Software Version 7.0.235.0
2 AIR-WLC2112-K9 - Software Version 7.0.235.0
10 AIR-LAP1252AG-T-K9 - Software Version 7.0.235.0
10 AIR-LAP1131AG-A-K9 - Software Version 7.0.235.0
I am adding a Cisco AP c3502-I-K9 to network.
It does not join any of the controllers.
Led is cycling through green, red, and off - that means "discovery/join process in progress" - never ends.
As wireless network is doing fine, I had only added to dhcp server dhcpd-subnet.conf file the above configuration:
class "Cisco AP c3500" {
match if option vendor-class-identifier = "Cisco AP c3500";
option vendor-class-identifier "Cisco AP c3500";
[Code].....
When we were installing some new APs, were plugged in to ports that were not configured on the WLC management VLAN.
This is the illustration
WLC management VLAN is VLAN 80 Management VLAN of infrastructure (Switches routers) is VLAN 10
The APs were plugged in to VLAN 10 and they were not able to associate themselves with the controllers.
Through research, those APs were getting a wrong IP address,
I did the Mode button, pressed for 30 secs, but this did not fix the problem, i thought it was going to clean the flash and bring the AP back to factory default I do not believe this happened.
We also added the cisco-capwap-controller.localdomain to our DNS servers, and then I rebotted the APs and still no luck.
What fixed the issue is we had to go to the DHCP server, release the IP addresses and we found those based on the macs of the APs. What is we do not have the mac addresses?
Now that I have the DNS entry created, if I plug in an AP on the wrong VLAN port will I be able to see it?
I am trying to get one AP to join the 2106 controller, it did join once then never again!! Now all I get is:
*Jan 22 11:16:22.088: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
[Code]....
I’m having a problem of joining new Aps( Ari-ap1242G-E-k9 ) to the following wireless LAN controller. WLC details as follows,
Model No - AIR-CT5508-K9
Software Version - 7.0.116.0
AP Model - ARI-AP1242G-E-K9
AP console logs attached in Error.jpg file
This is a new setup and has not worked yet. I have multiple 3602 APs and one 2504 Controller. I thought initially I could plug-in an AP into one of two POE Ports on the 2504. During debug mode I see that it has low power, was suprised that the 2504 switch can't fully power the AP? Is this correct?Anyways I have another POE switch that I am using with ample power. The configuration for my wireless is that it will be completely segmented off of my internal network as this is for guest access. So DNS servers are external so I cannot create host entries for the AP to discover the controller. With that being said I believe that is just one way for the discovery process to happen. I have my controller management interface and DHCP scope on the controller on the same subnet plugged into the same POE switch. The AP does seem to get a DHCP address and I can ping the controller from the AP. I cannot get any further then that. I will not join the controller and the radios get disabled. I get messages such as "discovery response from MWAR is rejected. I will post a debug log of the AP and its bootup process. This is new equipment so I would assume the firmware is somewhat up-to-date and the 3602 AP is somewhat the latest model.
View 3 Replies View Related1) AP was originally running a standalone image. I booted it into a so-called ROMMON or AP mode (ESC is the right key to make it boot into this mode).
I found a recovery image in its flash - c1140-rcvk9w8-mx. I made the AP boot from it by using "set" command and I see that it start booting using this recovery image. Here goes the question. Do all AP settings matter ? E.g. when I run "set" command from AP I see the following:
ap: set
?=
DEFAULT_ROUTER=10.0.0.1
Default_router=10.9.99.1
ENABLE_BREAK=yes
[Code].....
Iam having trouble to conect my 1121-AG AP`s to my 4404 WLC.
My WLC version is 7.0.116.0.
I can see he AP is getting an IP address from the controller(internal DHCP). But from some reason they can`t connect to the WLC. I have tried many things such as:
1)reset to default settings
2) move the AP to Autonumos mode and back to LWAPP mode -- didnt work.
1 of my AP 1121AG is working properly.
I try to configure an AP1131 as OfficeExtend but unfortunately I receive the following message from the debug command on the WLC5508: (Cisco Controller)
*spamApTask4: Oct 04 17:19:18.043: 00:1b:90:74:37:e0 Discovery Request from XX.XX.XX.XX:14847
*spamApTask4: Oct 04 17:19:18.043: 00:1b:90:74:37:e0 Join Priority Processing status =
[Code].....
we have WLC 4400, we have 40 APs with model no. AIR-LAP1131AG-N-K9 but we recenlty got an AP with model no. AIR-LAP1131AG-E-K9 which is unable to join WLC.
View 3 Replies View Relatedwe are running 5500-series WLC and AIR-LAP1131 and AIR-CAP3502 APs. Now we are trying to have new 1600-series AP's working with 5500WLCs. How to get this combo working.
WLC is running 7.4.100 sw version, and AP will join to controller but it won´t work.[code] I can´t find any kinf off document about invalid event 10 & state 5 combination erros message.
I'm trying to use 1142 APs with a 2504 Wireless Controller through a D-Link 48PT GBIT XSTACK SWITCH (DLI-DGS-3120-48PC/SI).At any rate, the 1142 AP joins with the wireless controller ONLY when I attach it directly to the controller. When connected directly to the controller the AP functions normally and all is well. When I attach it through the D-Link switch, the AP flashs green several times, indicating that it can't find the controller. I suspect that there's some setting on the D-Link switch that's preventing the AP from seeing the controller.
View 6 Replies View RelatedI am not able to join 1042 wireless AP with 2106 controller, even i mention that controller ip is 192.168.200.5 it try to join with controller on 192.168.200.6 ip address always. following are the error logs i can see on console.
*Nov 30 19:50:20.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:20.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Nov 30 19:50:21.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:21.436: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.200.6
*Nov 30 19:50:21.436: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
[code]....
We have two controllers 7510 with the same config (SSID, Mobility Groups, etc)... All APs now was joined in wlc01... If we try to one o more APs join to another controller.. it's is not possible and debug show this . [code]
View 1 Replies View Relatedi have configured cisco LAP1240 in H-Reap Mode for multiple branch offices with Local switching and central authentication. one of the branch's AP does not join the controller in HQ while the others are all ok. i have firewall only in HQ, i did priming first for all APs like let them join the controller and configure controller IP in high availbility, and H-Reap config and assign SSID to map with the branch local vlan. when i faced this issue first time i brought back ap and configure a static IP address for AP than recheck them again but the problem still same. since i have only one firewall in the network and also other branches joined the controller through that firewall and no issues.
View 3 Replies View Relatedoutput are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
Can 2 Aironet 1042's using WDS handoff a session between them without any other network hardware needed?
View 1 Replies View RelatedWe have couple of Cisco Aironet 3500 Series access points with the following P/N: "AIR-CAP3501E-A-K9", we have discovered that we need a wireless LAN controller to connect those new access points!, however, we do not have any wireless controller in our LAN.
We even tried to CLI through the console port but we could not set any static IP on it!, after reading on Cisco site we discover that this type of AP is called "Lightweight Access Point" LAP which handles all the management tasks to the controller!
So what shall we do! is it impossible to operate them without the controller?
Cisco Aironet 3602I is stand alone or need a controller ?
View 8 Replies View RelatedIs it possible to set an Aironet 1232AG-A-K9 as a repeater while still using a 4402 controller? I have some wireless security cameras in our parking lots that I need to extend wireless to and I have a handful of 1232 points that I am not using. I have some omni antennas and a yagi directional that I was planning on using.Everything I am reading talks about configuring the AP while in automous mode, not while running the lightweight image.
View 2 Replies View RelatedCan I connect various Aironet 1242 to Wireless controller 2500?
View 4 Replies View RelatedI've recently purchased a 2504 Wireless controller, and I have 10 2600 APs to deploy. I think I've set up the wireless controller OK - there doesn't seem to be much that needs to be done! But I just can't seem to register an AP onto the system.
Just to briefly outline what I have done, I have connected to the Wireless Controller via terminal emulator and run through the setup, then I have connected OK to the web interface, and I am able to view and amend the controller's configuration. So I have setup a WLAN and thats about it.
Next up I have powered on one of my 2600 APs, and I am able to view it working via terminal emulator again. But I am seeing it continually running the same routine to connect to a controller, and all the time it just fails. Below is what I am seeing.
One thing that I am unsure about is that I am unable to connect to the AP config pages via web browser, using the IP 192.168.0.97 (although it does ping okay). Is that odd?
And the main question - why doesn't the AP connect to the wireless controller? Do the APs need to be authroized on the controller first? If I check the controller's web interface, under Monitor - Statistics - AP Join, I can see the AP listed with Status "Not Joined" but I don't know what I need to do to make it join!
*Mar 1 02:28:54.579: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.*Mar 1 02:28:57.583: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.*Mar 1 02:28:57.651: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.0.97, mask 255.255.255.0, hostname APb0fa.eb56.5abf(code)
i'am trying to configure an AP1121g on my controller wlc5508 7.2 but i'am facing a compatibility issue.
View 5 Replies View RelatedI would like to buy Cisco Aironet 1260 Access Points, i just want to use them independantly so i want to know do they work without the Wireless LAN Controller? or i have to have the controller for them to work? they will be in different locations so i cant have a controller per each location.
View 9 Replies View RelatedI have installed/setup a cisco 2504 wireless controller and 3 aironet 1142 access points using the basic config on a windows sbs 2008 domain, the problem is that the clients that are connected to the 2504 aint getting the there ip addr from the AD but from the wireless controller, and there cant reach the clients on wifi from the clients that are connected to lan, is there anyway that i cant change this so that a client on lan can see the client on wlan and vice versa.
View 5 Replies View RelatedI try to join an ACS v. 5.3 to the domain. For my acs in Location A, I can join without problems using my account. When I try to join the ACS in location B to the same domain with the same account, it doesnt work.I looked at the debug log files for the ad client, and noticed, that the ACS in location B goes to a certain Domain Controller. However, I would have expected the ACS to contact another DC, which is located on the same location as the ACS ... this doesnt happen.
My question: How does the ACS determine what DC to contact ? Is it possible to force the AC to join by connecting a certain DC ?
Can I configure Multiple SSID (Guest/Corporative) on Cisco Aironet 3600i AP via Cisco 2504 Wireless controller?
View 1 Replies View RelatedI just started a project to make a guest wireless network available at every site in my enterprise. Guest wireless networks are currently available at some sites. Two key goals of this project is to enable WPA/WPA2 encryption and to develop a web based registration/autentication solution. All of the sites have a mixture of 1230, 1240, and 1250 autonomous access points. What do I need to do/get in order to make this happen?
View 3 Replies View Relatedif i can configure the cisco aironet 3500i without WLC controller.
View 1 Replies View Related