I am trying to get one AP to join the 2106 controller, it did join once then never again!! Now all I get is:
*Jan 22 11:16:22.088: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
[Code]....
I am not able to join 1042 wireless AP with 2106 controller, even i mention that controller ip is 192.168.200.5 it try to join with controller on 192.168.200.6 ip address always. following are the error logs i can see on console.
*Nov 30 19:50:20.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:20.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Nov 30 19:50:21.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:21.436: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.200.6
*Nov 30 19:50:21.436: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
[code]....
I setup a mini wireless LAN network lab with a not for resale 2106 wireless lan controller and a sales air-lap1242ag access point. I do not have a DHCP and DNS in my lab environment. I have configured the WLC with the basic configuration using the CLI wizard, i also configured the WLC as a DHCP server for clients that will be connecting to the APs associated to the controller.
I powered up the AP and connect the ethernet port directly to the controller, the controller issued an IP address to the AP, the AP downloaded a new operating system from the controller but failed to join the controller.
I check both debug message on the controller console and the trap messages on the controller's GUI and it say the AP could not download a configuration from the controller and it is beacuse of invalid license. Below is the trap message:
Configuration Phase Statistics Requests ReceivedResponses SentUnsuccessful Request ProcessedReason For Last Unsuccessful AttemptLast Successful Attempt TimeLast Unsuccessful Attempt TimeLast Error SummaryLast AP Message Decryption FailureLast AP Connection FailureLast Error Occurred Last Error Occurred ReasonLast Join Error Timestamp
Also, I tried to log into the GUI of the AP using the both the username and password ''Cisco'' but I cannot get into the device. I can only get in through the CLI. In the CLI, almost all the commands I enter gives an error the it is disabled. I don't know what to do any more, I want to know if the access point is faulty or i am not doing the right thing.
how I can find out what version of SSH that a cisco 2106 wireless LAN controller is using?Is there a CLI I can type to figure that out or do they only support one version?
View 1 Replies View Relatedafter an unplanned power outage the WLAN in our office has stopped routing. Clients can associate and get an IP address from the DHCP server on the controller but cannot get past the controller. A PC on the LAN can ping the default gateway of the SSID (dynamic interface) but cannot ping the client. Attached is a diagram of the setup. I am trying to find out how to add a default/static route via the L3 switch that the controller is connected to but am unable to do so either through the CLI or GUI. The controller (AIR-WLC2106-K9) is operating on ver 5.2.157.0.
View 5 Replies View RelatedI have a question to migrate a customer from a 2106 controller to a 2504 controller. Can I use the configuration file with both controllers having the same version?
Or is there another way not having to do it again manually? The old configuration is OK, only the hardware is end of sale.
I would like to get webauth bundle sample to create custom page for our AP controllers but I'm unable to find the sample .tar within the WCS itself.Some other WCS manuals has references in them that says there should be link to download sample from WCS but clearly 2106 hasn't got one.There's one in download section "webauth bundle 1.0.2.zip" but this is for registered partners and costumers, we are not registered as partners and cannot download the sample ourselves.
View 2 Replies View Relatedi converted the C1310 to LAP using upgrade tool. but the AP is not able to join the controller i was not able to view SHA Key in upgrade tool, so i ran the "debug pm pki enable " on the controler to get it. i'm still not able to view SHA key.
here is the output of debug command
*spamApTask0: May 21 15:07:43.527: 88:43:e1:d1:fc:9e Received LWAPP JOIN REQUEST from AP 88:43:e1:d1:fc:9e to cc:ef:48:b3:23:ef on port '13'
*spamApTask0: May 21 15:07:43.549: sshpmGetIssuerHandles: locking ca cert table
[Code].....
Network environment: (well configured and working fine)
2 AIR-WLC2106-K9 - Software Version 7.0.235.0
2 AIR-WLC2112-K9 - Software Version 7.0.235.0
10 AIR-LAP1252AG-T-K9 - Software Version 7.0.235.0
10 AIR-LAP1131AG-A-K9 - Software Version 7.0.235.0
I am adding a Cisco AP c3502-I-K9 to network.
It does not join any of the controllers.
Led is cycling through green, red, and off - that means "discovery/join process in progress" - never ends.
As wireless network is doing fine, I had only added to dhcp server dhcpd-subnet.conf file the above configuration:
class "Cisco AP c3500" {
match if option vendor-class-identifier = "Cisco AP c3500";
option vendor-class-identifier "Cisco AP c3500";
[Code].....
When we were installing some new APs, were plugged in to ports that were not configured on the WLC management VLAN.
This is the illustration
WLC management VLAN is VLAN 80 Management VLAN of infrastructure (Switches routers) is VLAN 10
The APs were plugged in to VLAN 10 and they were not able to associate themselves with the controllers.
Through research, those APs were getting a wrong IP address,
I did the Mode button, pressed for 30 secs, but this did not fix the problem, i thought it was going to clean the flash and bring the AP back to factory default I do not believe this happened.
We also added the cisco-capwap-controller.localdomain to our DNS servers, and then I rebotted the APs and still no luck.
What fixed the issue is we had to go to the DHCP server, release the IP addresses and we found those based on the macs of the APs. What is we do not have the mac addresses?
Now that I have the DNS entry created, if I plug in an AP on the wrong VLAN port will I be able to see it?
I’m having a problem of joining new Aps( Ari-ap1242G-E-k9 ) to the following wireless LAN controller. WLC details as follows,
Model No - AIR-CT5508-K9
Software Version - 7.0.116.0
AP Model - ARI-AP1242G-E-K9
AP console logs attached in Error.jpg file
When I check the AP join statistics I see the following: Reason For Last Unsuccessful Attempt RADIUS authorization is pending for the AP, I don't run a radius server and don't know how to get around this so that the device can join.
View 4 Replies View RelatedThis is a new setup and has not worked yet. I have multiple 3602 APs and one 2504 Controller. I thought initially I could plug-in an AP into one of two POE Ports on the 2504. During debug mode I see that it has low power, was suprised that the 2504 switch can't fully power the AP? Is this correct?Anyways I have another POE switch that I am using with ample power. The configuration for my wireless is that it will be completely segmented off of my internal network as this is for guest access. So DNS servers are external so I cannot create host entries for the AP to discover the controller. With that being said I believe that is just one way for the discovery process to happen. I have my controller management interface and DHCP scope on the controller on the same subnet plugged into the same POE switch. The AP does seem to get a DHCP address and I can ping the controller from the AP. I cannot get any further then that. I will not join the controller and the radios get disabled. I get messages such as "discovery response from MWAR is rejected. I will post a debug log of the AP and its bootup process. This is new equipment so I would assume the firmware is somewhat up-to-date and the 3602 AP is somewhat the latest model.
View 3 Replies View Related1) AP was originally running a standalone image. I booted it into a so-called ROMMON or AP mode (ESC is the right key to make it boot into this mode).
I found a recovery image in its flash - c1140-rcvk9w8-mx. I made the AP boot from it by using "set" command and I see that it start booting using this recovery image. Here goes the question. Do all AP settings matter ? E.g. when I run "set" command from AP I see the following:
ap: set
?=
DEFAULT_ROUTER=10.0.0.1
Default_router=10.9.99.1
ENABLE_BREAK=yes
[Code].....
my access point 1230 fail to join the controller. The image is C1200-k9w7-mx.123-8.JA2. I tried to reboot it but it does not join to controller. How do I initiate the discovery process again to make this AP to join? Should I convert it back to autonomous AP and then LWAPP process again? I can ping the AP from the controller and the AP is in the same VLAN with controller.
View 3 Replies View RelatedIam having trouble to conect my 1121-AG AP`s to my 4404 WLC.
My WLC version is 7.0.116.0.
I can see he AP is getting an IP address from the controller(internal DHCP). But from some reason they can`t connect to the WLC. I have tried many things such as:
1)reset to default settings
2) move the AP to Autonumos mode and back to LWAPP mode -- didnt work.
1 of my AP 1121AG is working properly.
I try to configure an AP1131 as OfficeExtend but unfortunately I receive the following message from the debug command on the WLC5508: (Cisco Controller)
*spamApTask4: Oct 04 17:19:18.043: 00:1b:90:74:37:e0 Discovery Request from XX.XX.XX.XX:14847
*spamApTask4: Oct 04 17:19:18.043: 00:1b:90:74:37:e0 Join Priority Processing status =
[Code].....
we have WLC 4400, we have 40 APs with model no. AIR-LAP1131AG-N-K9 but we recenlty got an AP with model no. AIR-LAP1131AG-E-K9 which is unable to join WLC.
View 3 Replies View Relatedwe are running 5500-series WLC and AIR-LAP1131 and AIR-CAP3502 APs. Now we are trying to have new 1600-series AP's working with 5500WLCs. How to get this combo working.
WLC is running 7.4.100 sw version, and AP will join to controller but it won´t work.[code] I can´t find any kinf off document about invalid event 10 & state 5 combination erros message.
I'm setting up a 2106 controller with 3 APs.
When I connect the APs to a port on our 3550 switch, the AP gets an IP and associates with the 2106 controller. I can ping the AP from a wired PC and associate a wireless client to it. When I connect them to the PoE ports that are on the controller, it gets an IP and associates with the controller but, I cannot ping it from a wired PC or wireless client but, I can associate a wireless client to it.
The AP manager and Management interfaces, under PHYSICAL OPERATION are configured for port 1, which is the port that connects the Controller to the rest of the network. Since the whole network is using VLAN 1, I set the VLANs for the Management interface and AP interface to 0, untagged. I noticed when I set the AP manager interface to 1 I get the same results.
I'm trying to use 1142 APs with a 2504 Wireless Controller through a D-Link 48PT GBIT XSTACK SWITCH (DLI-DGS-3120-48PC/SI).At any rate, the 1142 AP joins with the wireless controller ONLY when I attach it directly to the controller. When connected directly to the controller the AP functions normally and all is well. When I attach it through the D-Link switch, the AP flashs green several times, indicating that it can't find the controller. I suspect that there's some setting on the D-Link switch that's preventing the AP from seeing the controller.
View 6 Replies View RelatedWe have two controllers 7510 with the same config (SSID, Mobility Groups, etc)... All APs now was joined in wlc01... If we try to one o more APs join to another controller.. it's is not possible and debug show this . [code]
View 1 Replies View Relatedi have configured cisco LAP1240 in H-Reap Mode for multiple branch offices with Local switching and central authentication. one of the branch's AP does not join the controller in HQ while the others are all ok. i have firewall only in HQ, i did priming first for all APs like let them join the controller and configure controller IP in high availbility, and H-Reap config and assign SSID to map with the branch local vlan. when i faced this issue first time i brought back ap and configure a static IP address for AP than recheck them again but the problem still same. since i have only one firewall in the network and also other branches joined the controller through that firewall and no issues.
View 3 Replies View Relatedoutput are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
i'am trying to configure an AP1121g on my controller wlc5508 7.2 but i'am facing a compatibility issue.
View 5 Replies View RelatedI try to join an ACS v. 5.3 to the domain. For my acs in Location A, I can join without problems using my account. When I try to join the ACS in location B to the same domain with the same account, it doesnt work.I looked at the debug log files for the ad client, and noticed, that the ACS in location B goes to a certain Domain Controller. However, I would have expected the ACS to contact another DC, which is located on the same location as the ACS ... this doesnt happen.
My question: How does the ACS determine what DC to contact ? Is it possible to force the AC to join by connecting a certain DC ?
I have been trying to upgrade my WLC 2106, but it is stuck at rommon/grub mode.The steps are as follows
rommon #5> tftpdnldROMMON Variable Settings: ADDRESS=192.168.100.1 SERVER=192.168.100.10 GATEWAY=192.168.100.10 PORT=Ethernet0/0 VLAN=untagged IMAGE=AIR-WLC2100-K9-6-0-196-0.aes CONFIG=
[Code].....
We recently purchased a bundle of 3 1042N AP's with a 2106 WLC. I am able to get the controller on the network and am able to manage it through the https web gui. I am now trying to add one of the AP's to the controller and am getting an infinite loop on the AP upon bootup. I tried looking up the solution but could not find a good article that pertained to the problem I was having. One thing I did notice is the time on the AP is way offset, but when I do a clock set to change it to the actual date it doesnt stick on the next reload.
Here is the output:
using ÿÿÿÿ ddr static values from serial eeprom ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
[Code].....
I hava installed a WLC 2106 with 4 1252 Aps. Some laptops has dual radio wireless card, but others has just 2.4 Ghz card.
I have one SSID with WPA2/AES and 802.11X authentication.
With the laptops with dual radio the speed is in 300 Mpbs, but when is single 2.4 radio the max speed is 70Mpbs
If i use a 1252 ap with autonomous IOS, SSID with WPA2-PSK/AES this laptops single in 2.4 works to 144 Mbps
is there a knowed issue about 802.11x in 2.4 Ghz or i need to make a different configuration to can work in 2.4 with a speed of 144 Mbps?
I got my final assignment from school, and my teacher asked me to configure 2 Access Points (1200 series) directly on a Wireless Controler (Cisco 2106). I can't ask my teacher for any questions, cause he doesn't know how to configure it also, THAT's why he's asking me to do it.I've learned a lot of things about the default static interfaces (the "management" and "ap_manager" interface), but i can't seem to fully understand how to configure it.I want to use the Internal DHCP server of the WLC. How I can get those 2 Access Points working on the WLC. I only seem to get DHCP issues.
This is what i've done:
- Leave the configuration of the "management" and the "ap_manager" default (172.16.1.30 and 172.16.1.30). Bound to port 1
- Made a new interface "AP1" with IP-Address 10.0.0.10 (/24), default gateway 10.0.0.1. Primary DHCP server: 172.167.1.30
- Made a new interface "AP2" with IP-Address 192.168.1.10 (/24), default gateway 192.168.1.1. Primary DHCP server: 172.167.1.30
- Made 2 DHCP scopes within the 192.168.1.0 and 10.0.0.0 networks.
For some reason, when i boot up both AP's, the won't get any DHCP address.
I had a 2106 running 4.x software. It was upgraded to 7.x but will not read the config. How to downgrade the software?
View 4 Replies View RelatedWe have a 2106 that was configured by a former employee. No one left in the company is qualified to configure it. The wireless guest access used to work fine. We'd configure a guest user account. They would connect to the guest wireless, open a web browser and login. For some reason now there is no prompt for login. People can connect to it and get an IP address, but that's it. No login prompt or anything else from there.User Login Policies was set to 0 and I put it to 8. That didn't do anything. Under Web Auth > Web Login Page it's set to Internal (Default).
View 5 Replies View RelatedI have a WLC 2106 and 1242AG.it's a hotspot configuration.So in WLC, under controller tab, i have set my ap-manager ip, my management ip, my virtual ip (1.1.1.1) and my hotspot network range ip.I set also a DHCP range for the hotspot network.
In Wlans tab, i set my hotspot wlan, with no layer 2 security and for layer 3, i set none for layer 3 security and i use web policy authentication.I use local authentication and i created under security menu, under AAA tab, 3 local net users.
From pc number 1, i get ip from dhcp, and i have authentication web page, authentication is ok and i can surf on web.From pc number2, when user 1 from pc 1 is connected, i get ip from dhcp but i have not the authentication web page, i have not DNS resolution.when i try https:1.1.1.1/login.html, i have no answer.
And when user 1 is de-authenticated, the user 2 can surf on web.So only one user can surf at the same time. not good for a Hotspot.