Cisco Wireless :: AIR-CT5508-K9 - Unable To Join AP To Controller
Nov 7, 2012
I’m having a problem of joining new Aps( Ari-ap1242G-E-k9 ) to the following wireless LAN controller. WLC details as follows,
Model No - AIR-CT5508-K9
Software Version - 7.0.116.0
AP Model - ARI-AP1242G-E-K9
AP console logs attached in Error.jpg file
View 5 Replies
ADVERTISEMENT
Mar 10, 2012
we have WLC 4400, we have 40 APs with model no. AIR-LAP1131AG-N-K9 but we recenlty got an AP with model no. AIR-LAP1131AG-E-K9 which is unable to join WLC.
View 3 Replies
View Related
Nov 29, 2012
I am not able to join 1042 wireless AP with 2106 controller, even i mention that controller ip is 192.168.200.5 it try to join with controller on 192.168.200.6 ip address always. following are the error logs i can see on console.
*Nov 30 19:50:20.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:20.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Nov 30 19:50:21.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:21.436: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.200.6
*Nov 30 19:50:21.436: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
[code]....
View 4 Replies
View Related
Nov 6, 2012
output are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
View 1 Replies
View Related
May 6, 2013
i received access point types AIR-LAP1252AG-E-K9, which i want to connect to my wlan controller AIR-CT5508-K9. Update from IOS etc. is working fine. Also all access points are recognized by the controller.We got the AIR-LAP1252AG-E-K9 with two antenna versions.
View 1 Replies
View Related
Feb 24, 2011
I want to confirm if the access point (AIR-AP1141N-E-K9) can work with the Wireless LAN Controller (AIR-CT5508-25-k9)
View 2 Replies
View Related
Jan 28, 2013
Whether we can configure HA between AIR-CT5508-100-K9 and AIR-CT5508-25-K9. Or we should require this AIR-CT5508-HA-K9 ?
View 6 Replies
View Related
Oct 3, 2012
I have issue about Wireless controler , i have 2x WS-C3750G-24WS and 1x AIR-CT5508-50-K9 , i have max 50 access point license and i can't upgrading because WS-C3750G-24WS is and of life , can i use AIR-CT5508-50-K9 with 3750G to work together? , mobility and everything....
View 1 Replies
View Related
May 20, 2013
i converted the C1310 to LAP using upgrade tool. but the AP is not able to join the controller i was not able to view SHA Key in upgrade tool, so i ran the "debug pm pki enable " on the controler to get it. i'm still not able to view SHA key.
here is the output of debug command
*spamApTask0: May 21 15:07:43.527: 88:43:e1:d1:fc:9e Received LWAPP JOIN REQUEST from AP 88:43:e1:d1:fc:9e to cc:ef:48:b3:23:ef on port '13'
*spamApTask0: May 21 15:07:43.549: sshpmGetIssuerHandles: locking ca cert table
[Code].....
View 3 Replies
View Related
Oct 18, 2012
Network environment: (well configured and working fine)
2 AIR-WLC2106-K9 - Software Version 7.0.235.0
2 AIR-WLC2112-K9 - Software Version 7.0.235.0
10 AIR-LAP1252AG-T-K9 - Software Version 7.0.235.0
10 AIR-LAP1131AG-A-K9 - Software Version 7.0.235.0
I am adding a Cisco AP c3502-I-K9 to network.
It does not join any of the controllers.
Led is cycling through green, red, and off - that means "discovery/join process in progress" - never ends.
As wireless network is doing fine, I had only added to dhcp server dhcpd-subnet.conf file the above configuration:
class "Cisco AP c3500" {
match if option vendor-class-identifier = "Cisco AP c3500";
option vendor-class-identifier "Cisco AP c3500";
[Code].....
View 13 Replies
View Related
Oct 15, 2012
When we were installing some new APs, were plugged in to ports that were not configured on the WLC management VLAN.
This is the illustration
WLC management VLAN is VLAN 80 Management VLAN of infrastructure (Switches routers) is VLAN 10
The APs were plugged in to VLAN 10 and they were not able to associate themselves with the controllers.
Through research, those APs were getting a wrong IP address,
I did the Mode button, pressed for 30 secs, but this did not fix the problem, i thought it was going to clean the flash and bring the AP back to factory default I do not believe this happened.
We also added the cisco-capwap-controller.localdomain to our DNS servers, and then I rebotted the APs and still no luck.
What fixed the issue is we had to go to the DHCP server, release the IP addresses and we found those based on the macs of the APs. What is we do not have the mac addresses?
Now that I have the DNS entry created, if I plug in an AP on the wrong VLAN port will I be able to see it?
View 3 Replies
View Related
Jan 21, 2012
I am trying to get one AP to join the 2106 controller, it did join once then never again!! Now all I get is:
*Jan 22 11:16:22.088: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
[Code]....
View 31 Replies
View Related
Aug 6, 2012
When I check the AP join statistics I see the following: Reason For Last Unsuccessful Attempt RADIUS authorization is pending for the AP, I don't run a radius server and don't know how to get around this so that the device can join.
View 4 Replies
View Related
Oct 16, 2012
This is a new setup and has not worked yet. I have multiple 3602 APs and one 2504 Controller. I thought initially I could plug-in an AP into one of two POE Ports on the 2504. During debug mode I see that it has low power, was suprised that the 2504 switch can't fully power the AP? Is this correct?Anyways I have another POE switch that I am using with ample power. The configuration for my wireless is that it will be completely segmented off of my internal network as this is for guest access. So DNS servers are external so I cannot create host entries for the AP to discover the controller. With that being said I believe that is just one way for the discovery process to happen. I have my controller management interface and DHCP scope on the controller on the same subnet plugged into the same POE switch. The AP does seem to get a DHCP address and I can ping the controller from the AP. I cannot get any further then that. I will not join the controller and the radios get disabled. I get messages such as "discovery response from MWAR is rejected. I will post a debug log of the AP and its bootup process. This is new equipment so I would assume the firmware is somewhat up-to-date and the 3602 AP is somewhat the latest model.
View 3 Replies
View Related
Apr 11, 2012
1) AP was originally running a standalone image. I booted it into a so-called ROMMON or AP mode (ESC is the right key to make it boot into this mode).
I found a recovery image in its flash - c1140-rcvk9w8-mx. I made the AP boot from it by using "set" command and I see that it start booting using this recovery image. Here goes the question. Do all AP settings matter ? E.g. when I run "set" command from AP I see the following:
ap: set
?=
DEFAULT_ROUTER=10.0.0.1
Default_router=10.9.99.1
ENABLE_BREAK=yes
[Code].....
View 27 Replies
View Related
May 7, 2012
my access point 1230 fail to join the controller. The image is C1200-k9w7-mx.123-8.JA2. I tried to reboot it but it does not join to controller. How do I initiate the discovery process again to make this AP to join? Should I convert it back to autonomous AP and then LWAPP process again? I can ping the AP from the controller and the AP is in the same VLAN with controller.
View 3 Replies
View Related
Jan 4, 2012
Iam having trouble to conect my 1121-AG AP`s to my 4404 WLC.
My WLC version is 7.0.116.0.
I can see he AP is getting an IP address from the controller(internal DHCP). But from some reason they can`t connect to the WLC. I have tried many things such as:
1)reset to default settings
2) move the AP to Autonumos mode and back to LWAPP mode -- didnt work.
1 of my AP 1121AG is working properly.
View 11 Replies
View Related
Oct 4, 2010
I try to configure an AP1131 as OfficeExtend but unfortunately I receive the following message from the debug command on the WLC5508: (Cisco Controller)
*spamApTask4: Oct 04 17:19:18.043: 00:1b:90:74:37:e0 Discovery Request from XX.XX.XX.XX:14847
*spamApTask4: Oct 04 17:19:18.043: 00:1b:90:74:37:e0 Join Priority Processing status =
[Code].....
View 5 Replies
View Related
Feb 27, 2013
we are running 5500-series WLC and AIR-LAP1131 and AIR-CAP3502 APs. Now we are trying to have new 1600-series AP's working with 5500WLCs. How to get this combo working.
WLC is running 7.4.100 sw version, and AP will join to controller but it won´t work.[code] I can´t find any kinf off document about invalid event 10 & state 5 combination erros message.
View 25 Replies
View Related
Apr 1, 2012
I'm trying to use 1142 APs with a 2504 Wireless Controller through a D-Link 48PT GBIT XSTACK SWITCH (DLI-DGS-3120-48PC/SI).At any rate, the 1142 AP joins with the wireless controller ONLY when I attach it directly to the controller. When connected directly to the controller the AP functions normally and all is well. When I attach it through the D-Link switch, the AP flashs green several times, indicating that it can't find the controller. I suspect that there's some setting on the D-Link switch that's preventing the AP from seeing the controller.
View 6 Replies
View Related
Jun 7, 2012
We have two controllers 7510 with the same config (SSID, Mobility Groups, etc)... All APs now was joined in wlc01... If we try to one o more APs join to another controller.. it's is not possible and debug show this . [code]
View 1 Replies
View Related
Oct 14, 2012
i have configured cisco LAP1240 in H-Reap Mode for multiple branch offices with Local switching and central authentication. one of the branch's AP does not join the controller in HQ while the others are all ok. i have firewall only in HQ, i did priming first for all APs like let them join the controller and configure controller IP in high availbility, and H-Reap config and assign SSID to map with the branch local vlan. when i faced this issue first time i brought back ap and configure a static IP address for AP than recheck them again but the problem still same. since i have only one firewall in the network and also other branches joined the controller through that firewall and no issues.
View 3 Replies
View Related
Sep 12, 2012
i'am trying to configure an AP1121g on my controller wlc5508 7.2 but i'am facing a compatibility issue.
View 5 Replies
View Related
Jan 10, 2013
I have an (AIR-LAP1310G-E-K9R) and I tried to join it to WLC 5508 but I'm facing an error, I get this error from the LAP 1310 console as below:
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar 1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface
[Code].....
View 11 Replies
View Related
Mar 7, 2013
Below are the errors that i am getting while trying to register AP (2606e) with vWLC (7.3.112) .
That is the error on vwlc
[code]....
But in wlc statistis we are able to see the ap join mac, screen shot is attached
View 6 Replies
View Related
Sep 5, 2012
I try to join an ACS v. 5.3 to the domain. For my acs in Location A, I can join without problems using my account. When I try to join the ACS in location B to the same domain with the same account, it doesnt work.I looked at the debug log files for the ad client, and noticed, that the ACS in location B goes to a certain Domain Controller. However, I would have expected the ACS to contact another DC, which is located on the same location as the ACS ... this doesnt happen.
My question: How does the ACS determine what DC to contact ? Is it possible to force the AC to join by connecting a certain DC ?
View 2 Replies
View Related
Jul 26, 2011
ISP: CharterType: CableRouters: Belkin N150 & Linksys E1200Devices: Laptop, ipad, desktop w/wireless card, hardwired desktopI had random issues with the Belkin router. I was able to hard-wire connect via the router but very randomly my wifi signal would go out and I would be completely unable to connect to the router on any device. Now I am having the exact same issues with my new Linksys router.Sometimes the wifi works and others I get "Unable to connect to network" or "Unable to join network". I have not yet noticed a pattern.Here are the things I have tried:
* Replace router with new router
* Remove encryption
* Change encryption types
* Restart both cable modem & router
* Factory reset of router
* Changed Channels
* Reboot of router from http://192.168.1.1 interface than mine) are all called 2WIRE490 and 2WIRE593.
View 11 Replies
View Related
Nov 26, 2012
I have problems with an AP AIR-CAP1552C-E-K9 (MAC: 2c:36:f8:73:e8:a0 )this AP cannot join to WLC 5508 software version 7.2.110.0.The AP ever gets associated to WLC.
I saw timeout messages and this error message:
%CAPWAP-3-ECHO_ERR: capwap_ac_sm.c:5656 Did not receive heartbeat reply; AP: 2c:36:f8:73:e8:a0
I don´t see any connectivity issues between the AP and WLC thorugh HFC network.One time the AP join to WLC and I saw this messages in debug CAPWAP:
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Change State Event Response sent to 10.64.128.165:16012
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 CAPWAP State: Run
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Sending the remaining config to AP 10.64.128.165:16012
[code].....
View 2 Replies
View Related
Sep 10, 2012
I have a few AIR-AP1242-E-K9 AP that I have upgraded to LWAPP, after the upgrade the AP's don't join the controller. But some AIR-AP1232AG-E-K9 on the same site joins without any issues.The controller is: AIR-CT2504-K9, SW: 7.0.220.0. [code]
View 8 Replies
View Related
Aug 31, 2010
Ive been using this router for about 4 months now. suddenly it wont let me connect wirelessly through itouch nor through imac. it says Unable to join the network "linksys" eventhough "linksys" is indicated to be an available WIFI network and that signal is full. Problem is still the same even after i reset the router a couple of times pass 30seconds, set the security to No Password.if i connect the router with a cable it connects seamlessly and allows me to go online.
View 8 Replies
View Related
Apr 14, 2012
I reset my Dlink 615 wireless router. I held down the power and reset for 30 seconds and rebooting the system with the disc. I did change the router name, but believe everything else stayed the same. My desk top is working fine being "hardwired" but nothing wireless will connect.
I did see this time it installed Network Magic which I have since uninstalled and again rebooted the computer system and still cannot get the wireless to work. It shows the network available, but my password for some reason does not take.
View 1 Replies
View Related
Aug 7, 2011
I had PCs, Macs and other devices (iphone, itouch) able to connect fine to the WRT610n. I moved to an apartment and when I turned the network on all the devices could connect expect for the iphone and itouch. I have tried turning the wireless security off and MAC filtering off . I get the same "Unable to join the network" message.
View 7 Replies
View Related
May 1, 2012
I have a WLC 5508, AIR-LAP1142N APs and a SSID for students to connect to who bring their own device. I am still testing this and it has not been rolled out but I am running into some serious issues with joining the network. I am authenticating them through a RADIUS server (2008 R2). Problem: many of them cannot connect because they are lacking the certificate.
1. What is a good setup for authentication in a BYOD environment
2. If my setup is good what can I do to allow kids to use their computers on the wireless either without the certificate (which I know is unlikely) or what do I need to have them do to connect. I am hoping it does not involve hard wiring and getting the certificate from the server.
View 1 Replies
View Related