Unable To Join Network On Wireless Router?
Jul 26, 2011
ISP: CharterType: CableRouters: Belkin N150 & Linksys E1200Devices: Laptop, ipad, desktop w/wireless card, hardwired desktopI had random issues with the Belkin router. I was able to hard-wire connect via the router but very randomly my wifi signal would go out and I would be completely unable to connect to the router on any device. Now I am having the exact same issues with my new Linksys router.Sometimes the wifi works and others I get "Unable to connect to network" or "Unable to join network". I have not yet noticed a pattern.Here are the things I have tried:
* Replace router with new router
* Remove encryption
* Change encryption types
* Restart both cable modem & router
* Factory reset of router
* Changed Channels
* Reboot of router from http://192.168.1.1 interface than mine) are all called 2WIRE490 and 2WIRE593.
View 11 Replies
ADVERTISEMENT
Aug 31, 2010
Ive been using this router for about 4 months now. suddenly it wont let me connect wirelessly through itouch nor through imac. it says Unable to join the network "linksys" eventhough "linksys" is indicated to be an available WIFI network and that signal is full. Problem is still the same even after i reset the router a couple of times pass 30seconds, set the security to No Password.if i connect the router with a cable it connects seamlessly and allows me to go online.
View 8 Replies
View Related
Aug 7, 2011
I had PCs, Macs and other devices (iphone, itouch) able to connect fine to the WRT610n. I moved to an apartment and when I turned the network on all the devices could connect expect for the iphone and itouch. I have tried turning the wireless security off and MAC filtering off . I get the same "Unable to join the network" message.
View 7 Replies
View Related
Sep 19, 2012
My EA4500 router seems to drop mine and my wife's iPhone wifi connection at what appears to be the edge of my router's range. When we come back in range, our iPhone's intermittently give the error "Unable to join network.". And we're stuck in that mode. When I check the Devices menu in the CCC interface, I notice the iPhone device is configured and still online. However the "x" box to delete the device is greyed out because it's online. So how do I get out of this state and have my iPhone connect
View 2 Replies
View Related
Dec 8, 2012
My laptop's wifi is just working fine with TP Link but I'm unable to connect internet via wifi on my iPhone 3G. My iPhone's wifi just works fine in my office. Is there any solution available?
iPhone 3G 8MB
iOS 4.2.1
Modem Firmware: 06.15.00
Router: TP LINK TL-MR3220
Firmware Version: 3.13.12 Build 120524 Rel.60134n
Is there additional setting for iPhone?
View 1 Replies
View Related
Apr 14, 2012
I reset my Dlink 615 wireless router. I held down the power and reset for 30 seconds and rebooting the system with the disc. I did change the router name, but believe everything else stayed the same. My desk top is working fine being "hardwired" but nothing wireless will connect.
I did see this time it installed Network Magic which I have since uninstalled and again rebooted the computer system and still cannot get the wireless to work. It shows the network available, but my password for some reason does not take.
View 1 Replies
View Related
Nov 7, 2012
I’m having a problem of joining new Aps( Ari-ap1242G-E-k9 ) to the following wireless LAN controller. WLC details as follows,
Model No - AIR-CT5508-K9
Software Version - 7.0.116.0
AP Model - ARI-AP1242G-E-K9
AP console logs attached in Error.jpg file
View 5 Replies
View Related
Jan 10, 2013
I have an (AIR-LAP1310G-E-K9R) and I tried to join it to WLC 5508 but I'm facing an error, I get this error from the LAP 1310 console as below:
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar 1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface
[Code].....
View 11 Replies
View Related
Mar 7, 2013
Below are the errors that i am getting while trying to register AP (2606e) with vWLC (7.3.112) .
That is the error on vwlc
[code]....
But in wlc statistis we are able to see the ap join mac, screen shot is attached
View 6 Replies
View Related
Mar 10, 2012
we have WLC 4400, we have 40 APs with model no. AIR-LAP1131AG-N-K9 but we recenlty got an AP with model no. AIR-LAP1131AG-E-K9 which is unable to join WLC.
View 3 Replies
View Related
Nov 29, 2012
I am not able to join 1042 wireless AP with 2106 controller, even i mention that controller ip is 192.168.200.5 it try to join with controller on 192.168.200.6 ip address always. following are the error logs i can see on console.
*Nov 30 19:50:20.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:20.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Nov 30 19:50:21.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:21.436: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.200.6
*Nov 30 19:50:21.436: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
[code]....
View 4 Replies
View Related
Nov 26, 2012
I have problems with an AP AIR-CAP1552C-E-K9 (MAC: 2c:36:f8:73:e8:a0 )this AP cannot join to WLC 5508 software version 7.2.110.0.The AP ever gets associated to WLC.
I saw timeout messages and this error message:
%CAPWAP-3-ECHO_ERR: capwap_ac_sm.c:5656 Did not receive heartbeat reply; AP: 2c:36:f8:73:e8:a0
I don´t see any connectivity issues between the AP and WLC thorugh HFC network.One time the AP join to WLC and I saw this messages in debug CAPWAP:
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Change State Event Response sent to 10.64.128.165:16012
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 CAPWAP State: Run
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Sending the remaining config to AP 10.64.128.165:16012
[code].....
View 2 Replies
View Related
Sep 10, 2012
I have a few AIR-AP1242-E-K9 AP that I have upgraded to LWAPP, after the upgrade the AP's don't join the controller. But some AIR-AP1232AG-E-K9 on the same site joins without any issues.The controller is: AIR-CT2504-K9, SW: 7.0.220.0. [code]
View 8 Replies
View Related
Nov 6, 2012
output are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
View 1 Replies
View Related
May 1, 2012
I have a WLC 5508, AIR-LAP1142N APs and a SSID for students to connect to who bring their own device. I am still testing this and it has not been rolled out but I am running into some serious issues with joining the network. I am authenticating them through a RADIUS server (2008 R2). Problem: many of them cannot connect because they are lacking the certificate.
1. What is a good setup for authentication in a BYOD environment
2. If my setup is good what can I do to allow kids to use their computers on the wireless either without the certificate (which I know is unlikely) or what do I need to have them do to connect. I am hoping it does not involve hard wiring and getting the certificate from the server.
View 1 Replies
View Related
Feb 3, 2011
I'm having issues joining a remote PC to the corporate domain. The VPN we're using is SonicWall.Here's what the error is: Note: This information is intended for a network administrator. If you are not your network's administrator, notify the administrator that you received this information, which has been recorded in the fileC:Windowsdebugdcdiag.txt.The domain name "creatormail" might be a NetBIOS domain nameIf this is the case, verify that the domain name is properly registered with WINS.If you are certain that the name is not a NetBIOS domain name, then the following informationubleshoot your DNS configuration.The following error occurred when DNS was queried for the service location (SRV) resource record used to locate an Active Directory Domain Controller (AD DC) for domain "creatormail":[CODE]
View 3 Replies
View Related
May 6, 2013
I have configured a 1552, that is wired to network, as "Bridge" then "RootAP".
After reboot, I can see a MAP trying to join the network, in the "simple" logs of the controller :
"Mon May 6 17:29:43 2013 Mesh Node '04:da:d2:1f:4d:6f' failed to join controller, MAC address not in MAC filter list."
As I have done for the RAP, I enter this MAC address in the MAC Filtering area under Security tab. But this action doesn't solve the problem, I continue to see this message in the controller logs !
If I open a SSH session on the RAP, I can see this block of debug messages repeat all the time :
*May 6 15:29:33.163: %MESH-6-ADJ_VIDB_LINK: Mesh neighbor 04da.d21f.4d6f VIDB Virtual-Dot11Radio0 dot1x control
*May 6 15:29:33.167: %LINK-6-UPDOWN: Interface Virtual-Dot11Radio0, changed state to up
*May 6 15:29:34.167: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Dot11Radio0, changed state to up
*May 6 15:29:43.223: %MESH-6-LINK_UPDOWN: Mesh station 04da.d21f.4d6f link Down
*May 6 15:29:43.423: %MESH-6-ADJ_VIDB_LINK: Mesh neighbor 04da.d21f.4d6f VIDB Virtual-Dot11Radio0 going
When I take a look into detailled debug messages of the controller I can see this :
*spamReceiveTask: May 06 17:30:44.364: #LWAPP-6-RADIUS_AUTHORIZATION: spam_radius.c:242 The system could not send join reply, AP authorization failed; AP:04:da:d2:1f:4d:6f
I don't know why the system talks about dot1x or Radius Authorization, and if this is the source of my problems. On a other hand, I can see in the debug messages that there is a 2 hours lag time between controller (correct time) and RAP (incorrect, I suppose it synchronize with the controller?)
View 25 Replies
View Related
May 24, 2012
My Netgear adapter will not join the wireless network and keeps timing out.
View 3 Replies
View Related
Jan 29, 2011
I'd like to give my DIR-655 (rev. A4, firmware 1.32) to my brother for use as a repeater, to work with the weak signal in his apartment. But I don't see any way to configure the device to join an existing wireless network. Am I wasting my time?
View 7 Replies
View Related
Jan 30, 2012
i don't know how to connect to a network, to make an ipad work
View 1 Replies
View Related
Aug 9, 2011
Have two wifi in my area but can't get on them what do I need to do
View 1 Replies
View Related
Jun 20, 2011
how do I get Ipod to join network....my ipad works just fine?
View 1 Replies
View Related
Feb 17, 2011
When I click on Network under Places I can see Windows Network folder. When I click on the Windows Network folder it displays an error message of Unable to mount location...Failed to recieve share list from server.
View 1 Replies
View Related
Mar 13, 2011
I've been trying to get it to work all day.When I open up Hamachi it shows the main screen with two buttons. Create a new network and Join an existing network.I've tried both but when I click create or join it doesn't do anything. Like it actually does nothing at all.Doesn't even close the window.Everything stays open and it doesn't either create or join any networks.
View 1 Replies
View Related
Aug 27, 2012
Just to set the stage, we used to have a network which ran in the following order:
For wired workstations: bridged DSL modem->wireless Linksys E900 router->Dell PowerConnect 2824 switch->2 modular 4-port jacks->individual workstations For wireless: bridged DSL modem->wireless Linksys E900 router->workstations The workstations were set up to pick up IP addresses automatically.After an infrastructure upgrade where we added some Cat6 cables and swapped the modular jacks for a patch panel, we lost all connectivity. I restored the connectivity to the wired workstations by assigning IP addresses. But we have no wireless and I cannot access the router GUI at its IP address (even when plugged directly into the router). All the workstations show the default gateway as 192.168.10.1, so I don't know what's going on.
View 3 Replies
View Related
Apr 19, 2012
Due to bandwith requirements, we need to join a network with a RV016 to a network with an RV082 via a point to point air bridge. (VPN over adls was not cutting it) fortunatelly there is line of sight.
The info
LocationA LocationB
RV016 RV082
WAN1 ADSL modem WAN1 ADSL Modem
WAN2 DedicatedIP modem WAN2 Free
WAN3..7 free
[code]....
We need LAN-B endpoints to be able to reach servers on location A and viceversa.
We pre configured two point to point radios for the tower people to install. (we could change this configs)
Topology (crude sketch)[URL]
Our questions: best port to plug the radios into the RVs WAN ports? switch ports? What rules or static routes need to be created?
View 2 Replies
View Related
Jan 21, 2011
My customer has 3 computer
1- Windows xp
2- Win7
3- Apple
4 new sony laptop.
Vaio would not connect using WEP 40-bit key. Logged into Airport Extreme router with Airport setup utility for Windows from Apple. Updated firmware from 5.1.1 to 5.7. Reset Encryption from WEP to WPA/WPA2 Personal.Connected Vaio on Wifi using WPA2. Removed ethernet cable and connection was good at 54MB/s.Completed Windows Update
View 3 Replies
View Related
Feb 25, 2012
Just got a new(secondhand) laptop & have successfully connected it to the internet via my wireless router/modem, but can't get it onto my home network. It appears to work, says it's connected but shows no other computers & they don't show this one.The laptop is an Acer Travelmate 2428, running Win7 Professional. My 2 wirelessly networked PCs are running on WinXP & the printer is connected physically to one of those. The router/modem is an Edimax. In XP it talks about 'home networks' whereas Win7 has 'homegroups'. I've used the wizard to 'manually connect to a wireless network' which is how I networked the PCs. I've also tried all other options in the 'Network & Sharing Centre' including the troubleshooter which when 'troubleshooting network problems' only tells me my clock is not right. In the network & sharing centre under 'view your active networks it says 'home network' & next to homegroup says 'joined'.
View 7 Replies
View Related
May 11, 2012
I have a Linksys E1500 wireless router that I have had for about 3 months and it has been working great up until today. I realized non of my wireless devices could detect the network, so I got on my PC which is hard wired to the router and it to says it had no network connection. So I power cycled both the router and the modem. When it came back up, this PC that I am typing from now has an internet connection but is says it is connected to Network 2 instead of the routers name for the network. My other PC that is hard wired to the router says its not connected to the network, and when I open up the Cisco Connect software it tells me my router is not plugged in. Also, nothing works wirelessly.In the web control panel it still has all my setting intact but still looks like its not connected to the internet.
View 1 Replies
View Related
Feb 13, 2012
I am missing something and i dont no what but i am trying to ping a pc on the same network but get a destination host is unreachable. Can any one think of anything that could be causing this, i can ping the default gateway and internet address's?
!
interface FastEthernet0
no cdp enable
[Code].....
View 11 Replies
View Related
Jan 15, 2012
One moment the laptop was using the wireless connection from the router in our house and the next it lost internet access and then wasn't able to recognize the SSID or connection at all on the available wireless connections. We have reset the router and restarted the laptop countless times yet the only internet access we have is on the computer the router is hooked up to.The wireless connection works neither on the laptop nor the Wii, both previously works merely hours ago and with no problems until now.We assume there is an issue with the router itself, whether it be a loose ethernet cord (which only faintly can be moved in its place).It's almost as if the router is stopping them (Wii, and laptop) from having access. When we explore the wireless internet properties on the laptop, it shows the wireless connection, yet only there and doesn't give access to it. Could it be the router, or could the company have restricted WiFi only to the computer it is hooked up to?
View 1 Replies
View Related
Sep 4, 2011
I'm Using D-Link DIR 600 wireless router with my desktop CPU (Windows XP Professional SP1) using wired connection and Dell laptop (Windows 7 Ultimate) connected wirelessly. My problem is that I am able to access internet on bothsystems but they cannot see each other in network places. I am unable to sharefiles between the them. I have tried all the procedures mentioned in many forumsbut still not able to find a solution
View 4 Replies
View Related
Aug 18, 2012
I just updated the firmware on my ZyXEL NBG-416N router and now I cannot see the wireless network being broadcasted on my PC. Other devices in my home can view this network including my phone, HDTV and laptop. I have reset the router, modem and computer several times but my PC still cannot find that specific wireless network.I am using Windows 7 64-bitASUS 802.11n Wireless LAN CardAny reason that my computer is unable to find this specific network but can find others? switchie15 has chosen the best answer to his/her question.Click here to view the answer that was selected.
View 3 Replies
View Related
