Updated Firmware On ZyXEL NBG-416N Router / Unable To See Wireless Network On PC?
Aug 18, 2012
I just updated the firmware on my ZyXEL NBG-416N router and now I cannot see the wireless network being broadcasted on my PC. Other devices in my home can view this network including my phone, HDTV and laptop. I have reset the router, modem and computer several times but my PC still cannot find that specific wireless network.I am using Windows 7 64-bitASUS 802.11n Wireless LAN CardAny reason that my computer is unable to find this specific network but can find others? switchie15 has chosen the best answer to his/her question.Click here to view the answer that was selected.
View 3 Replies
ADVERTISEMENT
Dec 30, 2011
Ever since I updated my wireless NETGEAR WNR1000v2 Firmware to its current Version V1.1.2.28NA I'm unable to connect to the internet with my PSP Firmware version of 6.60. I used to be able to connect up with no problems. I can scan and it sees the connection and i'm able to set the PSP network settings up however when I go to test it it will not connect up.
View 4 Replies
View Related
Mar 4, 2012
Which I have never done since my dad bought it a few years ago. Now when I try re-installing the Linksys software it gets stuck when trying to identify the network from the cable modem through the router. I've tried every reset feature there is & nothing has worked! I'm I going to need a new router?
View 9 Replies
View Related
Jan 19, 2012
I wonder if an updated firmware for E3000 would come out. Current one have few web-interface issues at QoS, DHCP, Custom Routes and WiFi setup pages.
View 9 Replies
View Related
Jan 16, 2013
Where I can download an updated firmware for my WRT54G RG
View 4 Replies
View Related
Oct 28, 2012
Noticed this AM that a new firmware was releaesed to my EA6500!! Very surprised to find it Monday AM. I went ahead & updated my firmware but lost connectivity to my Comcast cable modem. I was leaving for work so I had to pull the router & revert back to my original Linksys router.zBig storm heading my way, figured the wifw ywould need internet to track Hurricane Sandy. Any others have a new firmware waiting for install this AM? Keeping my fingers corossed on this firmware upgrade. I'm hoping it solves the device map issue.
View 2 Replies
View Related
Jul 15, 2011
recently i have updated my firmware, once it said update complete, my internet shut down. I can get on the internet now, but i cant use my router. I have to run my ethernet through my modem now. I have tried resetting it many many times.
View 6 Replies
View Related
Aug 30, 2012
Now that Comcast is in the process of rolling out IPv^ to their customers nationwide, will there be a firmware update that properly displays the IPv6 /64 address as provided by the cable provider? Currently the only IPv6 address displayed is on the LAN page and is not configurable (greyed out) except for the prefix length. I already have a cable modem that will provide both IPv4 and IPv6 addresses as they are rolled out.
Currently running WRVS4400N v2 fw 2.0.2.1
View 1 Replies
View Related
Sep 17, 2012
We have three WAP4410N that loses the connection. We've updated the firmware, changed the equipment, repeatedly reconfigured, but the problem persists.Is used the firmware 2.0.5.3 with WPA2 Enterprise Mixed authentication.
View 5 Replies
View Related
Mar 27, 2012
Have a ZyXEL 600 wireless router - it has worked without issues for years.However yesterday evening my wireless router suddenly stopped broadcasting a signal. 2 different PC's and a wifi dongle attached to our TV were suddenly all unable to find my network.The WLAN light on the router was still lit up. I connected my Acer Aspire 5742Z laptop to the router via an ethernet cable and it worked fine. I connected to the router and it said there were no errors.
View 14 Replies
View Related
Apr 20, 2012
There is new firmware for the B series of the Dir-825 but the change log is not updated.
View 10 Replies
View Related
May 30, 2011
i have a ZyXel prestige 650H-31 Model # router and i'm not able to go on to configuration page of the router i tried 192.168.1.1 several times, even after system reboot and router reset, but of no use. I've a wire connection with desktop (RJ-45 port) not USB AND MY PPPoE lights never lit. originally when i entered the gateway 192.168.1.1 it asked me for username & password, since i didn't have the password at that time i tried to reset the router but after that when ever i entered 192.168.1.1 in the browser it never came up with the option to enter user name & password. I've checked all the wires are also connected. I tried prompt command and it showed that timed out thrice and then sent= 4 received= 0 lost= 100%. I had D-Link router prior to it and later connected the D-Link router an i was able to get connected to net and browse normally.
View 1 Replies
View Related
May 21, 2012
I have a P-660HW-T1 v3 its using V3.70(BYD.1) | 02/11/2010.when I try to update it to 3.70(BJZ.10)C0 the update fails to succeed.
View 1 Replies
View Related
Mar 12, 2013
I've been using ZYXEL PLA-401 v1 Homeplug adapters for years to connect various devices to my router for a "more stable" than wireless connection. This worked fine in my last house, connecting a switch in our office to the router. We've now moved and I have got some more homeplug adapters to make a few other more reliable connections.
Problem is, the new adapters can't see the old adapters on the homeplug network. They can see each other, as can the old ones. I suspect a firmware or network name mismatch - I've tried to change settings on each of them but the Zyxel utility doesn't appear to do much. I can't set the DAK names, nor can I change the network names. The firmware update utility doesn't work on Windows 7 (gives a cannot find Windows path error).
using the Zyxel configuration utility and firmware upgrade tool on Windows 7 / Ubuntu?
View 1 Replies
View Related
Mar 3, 2011
I keep having no internet connection on my home wireless network, usually when i download newer versions of software, such as iTunes or java. this only happens on my dell inspiron laptop 1525. my other computers in my house work just fine. i have windows vista on laptop. the only error message i get is:The network adapter Bluetooth Network Connection in not connected. the only solution i have found so far is to do a system restore to a previous date, and voila, i have my internet connection back, no problem.
View 3 Replies
View Related
Jul 6, 2012
first I replaced a new internal hard drive. Installed new and updated drivers. connected to the home wireless network. everything working well so far as of last week. this week, I replaced new battery and ran norton 360 updates. after the updated, I can't connect wirelessly to my home network. I checked if Norton is blocking the communication but I don't think it did.
View 3 Replies
View Related
Jan 22, 2012
Firmware downloaded, FW_WRT120N_1.0.06.001_US after pressing APPLY nothing happens after few minutes it says. "There is an error in the Content-type field. Click the Back button to return to the previous page and re-enter the information."
View 2 Replies
View Related
Jun 4, 2012
PowerArchiver compression sw (newest version) does not recognize the file as valid archive
View 4 Replies
View Related
Jan 8, 2012
The linksys E3000 Could really use a firmware update.. the last one was 12/01/2010Ver.1.0.04 (build 6)
View 6 Replies
View Related
Jul 6, 2011
I have a business class dell laptop that I have not used for a year or so (Dell support has expired). Last time I used it I had no problem conecting to our business/office linksys. I took the laptop home and tried to conect to a new cisco linksys e1000 wireless router (was not able to connect). As far as my laptop goes, what hardware (internal wireless adapter/etc) needs to be updated with latest drivers. Does the BIOS need to be updated? I am running Windows XP Pro. Other than the service pack (I am not at home so I can verify current service pack) what else needs to be brought up to date (hardware/software)? I have played with this for days and am done doing so until the laptop is totally made 'current". I will hard wire laptop to router to do these updates.
View 2 Replies
View Related
Mar 16, 2011
My internet (via wifi) works just fine. But here is the situation that has me baffled-I have a house that has ethernet wired ports in each room, then there is a central hub in my closet. In the hub, I have a grey ethernet cord that is labeled 'service'. This service wire connects to a board that features 12 ethernet ports, 1 of which says 'in', 1 says 'security interface' and has a little nub in it, and the other 10 are not labeled. The grey wire is in the 'in' port.So I am left with 10 ports- port 3 of 10 has a (phone cord size) cord in it, connecting into the 'line' port on my Qwest modem/router. (Qwest set this all up for me, by the way). The modem/router is obviously plugged into the wall. Now- remaining loose in the hub are 9 ethernet cords- 5 blue, 4 green. Each one of these is written on in sharpie, and has a room label on it. 'Family, living room, kitchen, etc...'. So, pretty obvious, I simply found which cord corresponds to the room I am trying to use (family GREEN is one, family BLUE is another). These 2 wires correspond to the top port, and bottom port of a switch plate that is in my family room. Now- inside the closet hub I plugged family GREEN and family BLUE into the back of the ROUTER, ports 1 and 2 (of 4 available). Now- I went back to the wall- connected ethernet wires into the wall plate and then into the ethernet devices I am trying to use (slingbox and directv dvr). Neither are working.
If I go to setup menu on dvr it says it cannot find a network, not getting an ip address. is that the slingbox red lights are both solid (which means there is a connection), and if I go back to the router ETH1 and ETH2 are lit up on the front, again implying that I have a valid connection. This isn't rocket science, but I must be doing something wrong. Are the family GREEN and family BLUE supposed to go into any of the 9 remaining ports that are open inside the closet hub? Because my thought was- let's say hypothetically I wanted to use every available wall jack in my house. There are 9 wall jacks total, but there are only 4 ports on the router. So this would not work. But, there are 9 ethernet ports open on the board in the closet. So I must need to use the ports in the closet, NOT on the router? If so, are these closet ports specific? Because (remember I have a phone like cord coming out of port 3, going into the 'line' port on my router/modem) I took this phone like cord out of port 3, plugged into port 4. and 5, and 6, 7, etc... and none of them would allow my wifi to work- the INT light goes off on the modem/router at that point. But when I plugged back into port 3 (where Qwest originally put it), INT lit back up and wifi worked again. So this makes me think that these 10 (9 remaining) ports are specific somehow? I know this was a lot to read. End result I am looking for- continue to use my wifi on the computer (the ONE place in my house there is no wall jack lol), and connect my slingbox and my directv dvr to the wall jack in my family room so I can (have slingbox) and get On-Demand content for directv.
View 5 Replies
View Related
Jul 29, 2012
I updated my Mac to OSX 10.8 and now every time I try to login to my work network (a windows network) it locks my account. Each time, my sysadmin unlocks my account and I am able to successfully login one time but then, if I login again (after restart or sleep) I am locked out.
View 1 Replies
View Related
Feb 8, 2012
I have one P-660HN-T1A ZyXEL wireless router at my home with 2mbps connection. ZyNOS Firmware Version: 3.40(UTU.0) my brother always keeps on downloading stuffs from bitTorrent and eats up all the bandwidth.
1. is there any way to put speed limit on each user of my wireless router??
2. or is there any way to just block torrent download on my router???
3. QOS [quality of service] setting on Zyxel router so that I make my priority higher than my brother?
View 4 Replies
View Related
Feb 17, 2011
I have a an old router that I changed out when I switched over to fibernet that was just gathering dust, so I decided to include it in my network to extend the wireless range, so the signal is stronger throughout the whole house.Now, the only reason I attach it is to extend the wireless distance, nothing more.Both routers are exactly the same (Zyxel P2602HWT), and the second router is connected through an ethernetcable going to the DSL port. I can connect to the SSID just fine, but it's not actually connected to the internet, only locally (as I can configure the router).I have turned OFF DHCP for the second router, that I only intend to use as a second access point.
View 1 Replies
View Related
Apr 23, 2012
I am trying to access the internet trough my WRT610N connected to a ZyXEL P-2601HN provided by my ISP.
I have the WRT610 all setup and working, but I cannot connect to the internet. The WRT610N is a the latest firmware version.
The WRT610 is connected (Internet) by cable to the Zyxel (one of the four ports)with a cat.5E patch cable.
the wireless is so much better on the WRT610N than the ZyXel.
View 3 Replies
View Related
Jun 23, 2011
I have two WS-C2950G-24-EI switches each of which were running software version 12.1(22)EA2-C2950-I6Q4L2-M. Both swtiches were viewable from Network Assistant version 5.6(3) and part of a community. I then updated the software on one of the switches to 12.1(22)EA14, and now Network Assistant will not add the new updated device to the community and gives an error of "WS-C2950G-24-EI is not supported as community member". Is the latest version (12.1(22)EA14) not supported by Network Assistant? The release notes indicate the Minimum Software Release is 12.1(22)EA4.
View 1 Replies
View Related
Sep 15, 2012
Just recently got a Zyxel VSG1432 router connected to the main computer in my home. I am now trying to connect my laptop wirelessly. It will connect to the router but says it is an unidentified network and it doesn't connect to the internet. There is an x in the network and sharing window.I have tried restarting the router, going to the router webpage and resetting to factory settings, none of this worked. Also contacted the service provider and spoke with two tech guys, but still no luck.
View 1 Replies
View Related
Aug 1, 2011
I need to create a VPN tunnel between two offices of the same company. I bought two Zyxel P-661HW-D to create the secure VPN tunnel but the problem is that the two offices has a ADSL connection with dynamic IP. Is possible, with this router, to use a DDNS service to create the VPN tunnel or it' s required to have static IP ?
View 1 Replies
View Related
Apr 29, 2013
Region : India
Model : TD-W8951ND
Hardware Version : V4
Firmware Version : 4.0.0 Build 120607
ISP : Airtel[/COLOR]
I have wifi connectivity issues. After continues usage the wifi connection fails suddenly. And doesn't work till I restart it.
View 2 Replies
View Related
Mar 1, 2012
I am in the midst of trying to update the controller firmware of a cisco wireless lan contoller 4402, and having some issues getting the file to transfer to the controller. i am currently running verison 5.0.148 on the controller and attempting to upgrade to the latest version of 7.0.230 and for whatever reason it continues to not transfer. I have tried all 3 methods of cli, gui and using wcs software. all the no avail , I have tried tftp32 and 3cdaemon with the same results.
The error that i am getting from 3cdaemon is got socket timeout aborting code 10054, failing at 66MB transfered. I increased the timeouts both on the wlc and the tftp client to no avail
the error i get on the wlc is Code file transfer failed - Error while writing output file
View 5 Replies
View Related
Oct 25, 2012
My internet connection is fine but I really need to update the firmware on my wireless adapter. I have no problem accessing the router's config page. I ran ipconfig to get the adapter IP (screenshot attached/192.168.2.104). When I type the IP into the browser I get the "cannot display webpage" msg. I have tried turning off the power to the router, disabling Norton's firewall (I disabled Norton completely), and nothing works. Do not tell me to restore factory defaults on the adapter because I tried to get to the configuration page of another wireless adapter I have and am having the same problem.
View 7 Replies
View Related
Jul 18, 2011
I have recently acquired one of these routers. I thought, being a Cisco product, it would be the bee's knees. It is not. After finally getting the network set up - no mean feat, although I do not claim any expertise, but had to resort to some other network management software to finally get it all running - the router drops either the WAN connection or the wireless connection many times a day. The laptops often show as being connected to the network/router, but are unable to access either the internet, or the router via the browser. Re-booting the router is the fix, but, hey, I can achieve that sort of performance with any old $20 router - none of my old Net gear routers was this troublesome.
The permanent fix would seem to be a firmware upgrade, but guess what? The only options available under the "Administration" tab are time setting and switch settings - no firmware upgrade. The supplied firmware is 1.01.09(001) Apr 7 2010. Why these products are supplied, as new, without the latest firmware installed beats me, but there you go.
View 4 Replies
View Related
Feb 9, 2012
I've seen a couple of expired threads on this subject, so I'm sorry for resurrecting it! I have just got a ZyXEL P660HN-TxA router/modem on my home landline to use for wifi with my smartphone. The problem I have is it won't stay connected for long. It connects quickly & browsing is fast for a few minutes, but then it just kicks me offI am still connected to the wifi, but I can't browse anything or re-connect to the internet. Sometimes I can use it for up to 10/15 minutes before it kicks me off. I have to reset the modem, or turn the wifi off then back on via my phone.
View 4 Replies
View Related
