Cisco Wireless :: Updated Firmware For WRVS4400N V2?
Aug 30, 2012
Now that Comcast is in the process of rolling out IPv^ to their customers nationwide, will there be a firmware update that properly displays the IPv6 /64 address as provided by the cable provider? Currently the only IPv6 address displayed is on the LAN page and is not configurable (greyed out) except for the prefix length. I already have a cable modem that will provide both IPv4 and IPv6 addresses as they are rolled out.
Which I have never done since my dad bought it a few years ago. Now when I try re-installing the Linksys software it gets stuck when trying to identify the network from the cable modem through the router. I've tried every reset feature there is & nothing has worked! I'm I going to need a new router?
We have three WAP4410N that loses the connection. We've updated the firmware, changed the equipment, repeatedly reconfigured, but the problem persists.Is used the firmware 2.0.5.3 with WPA2 Enterprise Mixed authentication.
I just updated the firmware on my ZyXEL NBG-416N router and now I cannot see the wireless network being broadcasted on my PC. Other devices in my home can view this network including my phone, HDTV and laptop. I have reset the router, modem and computer several times but my PC still cannot find that specific wireless network.I am using Windows 7 64-bitASUS 802.11n Wireless LAN CardAny reason that my computer is unable to find this specific network but can find others? switchie15 has chosen the best answer to his/her question.Click here to view the answer that was selected.
Noticed this AM that a new firmware was releaesed to my EA6500!! Very surprised to find it Monday AM. I went ahead & updated my firmware but lost connectivity to my Comcast cable modem. I was leaving for work so I had to pull the router & revert back to my original Linksys router.zBig storm heading my way, figured the wifw ywould need internet to track Hurricane Sandy. Any others have a new firmware waiting for install this AM? Keeping my fingers corossed on this firmware upgrade. I'm hoping it solves the device map issue.
Ever since I updated my wireless NETGEAR WNR1000v2 Firmware to its current Version V1.1.2.28NA I'm unable to connect to the internet with my PSP Firmware version of 6.60. I used to be able to connect up with no problems. I can scan and it sees the connection and i'm able to set the PSP network settings up however when I go to test it it will not connect up.
recently i have updated my firmware, once it said update complete, my internet shut down. I can get on the internet now, but i cant use my router. I have to run my ethernet through my modem now. I have tried resetting it many many times.
I have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine.
Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?
We need to update the firmware for a small business router WRVS4400N. Unfortunately, I can't even burn the ISO file to CD after downloading it as instructed. I get the following error message: "The selected disk image file Isn't valid." I'm using a Windows 7 Ultimate computer.
I downloaded the proper firmware update for my version V2.0.1.3 router several times, but each time I get the same message.
The main reason we purchased this router for our business for for the extra layer of protection with ProtectLink. It has been over two years now, and we still have not got our ProtectLink service installed because we are unable to install the service until the firmware is updated.
After doing some research online, we found-out that the ISO file needs to be padded to 2 Kb in order to be valid for burning. The ISO firmware file you provide for this update is not according to my calculations. We have no way of converting the file myself and don't know what to do about this situation.
We are extremely taken-back at the fact that I must submit my issue here on a forum rather than address the issue directly to Cisco Support. We are very disappointed with Cisco support as they appear to want to charge additional money just to get an initial shipped-problem remedied. You would think that the company that essential built the internet infrastructure would be more considerate to their customers. We will never purchase another Cisco product given this level of terrible support.
I am using a Linksys WRVS4400N V1 running firmware 1.1.08 and although generally performance is good there are a few issues which I was hoping a firmware update could fix, however I cannot find it anywhere on the Cisco website.
Since 3 Days, i use a WRVS4400N v2, boarded with the newest firmware V2.0.0.8-ETSI. I configured Router and QOS and it worked fine. Yesterday, i upped the IPS Signature to the latest Version 1.42 (RVS4000_WRVS4400N_IPS_Signature_v1.42.zip).Now I have the same Problem like here:
[code].....
I add a service in Service Management an if I use this service in the priority table, another (one of the default) service appeared.The Problem: I did not have Version1, but Version 2 an no newer firmware is available at the Cisco site. I also never upgraded the firmware, because the latest available is installed. I also reset the Router to factory defaults and reconfige it, but the problem still occurs. I also used different browsers to configure (IE, FF, Opera). Next strange thing: If i add more than 10 services in the service management, and use this in the priority table, the whole QOS-Page is corrupt. The Router automatically disable QOS and if I want to enable it, there is no Priority Table or Save Button on the site. There's a bug in the select list, because only a few entries of the default services are shown.
I have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine. Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?
I keep having no internet connection on my home wireless network, usually when i download newer versions of software, such as iTunes or java. this only happens on my dell inspiron laptop 1525. my other computers in my house work just fine. i have windows vista on laptop. the only error message i get is:The network adapter Bluetooth Network Connection in not connected. the only solution i have found so far is to do a system restore to a previous date, and voila, i have my internet connection back, no problem.
first I replaced a new internal hard drive. Installed new and updated drivers. connected to the home wireless network. everything working well so far as of last week. this week, I replaced new battery and ran norton 360 updates. after the updated, I can't connect wirelessly to my home network. I checked if Norton is blocking the communication but I don't think it did.
I have a business class dell laptop that I have not used for a year or so (Dell support has expired). Last time I used it I had no problem conecting to our business/office linksys. I took the laptop home and tried to conect to a new cisco linksys e1000 wireless router (was not able to connect). As far as my laptop goes, what hardware (internal wireless adapter/etc) needs to be updated with latest drivers. Does the BIOS need to be updated? I am running Windows XP Pro. Other than the service pack (I am not at home so I can verify current service pack) what else needs to be brought up to date (hardware/software)? I have played with this for days and am done doing so until the laptop is totally made 'current". I will hard wire laptop to router to do these updates.
I downloaded an update for the 1370 wireless card from the microsoft site and now my wireless network doesn't work. I went to the dell site and got the driver directly from the dell site (R140747.EXE) and it fails after it reached 59% complete. I tried another download recommended from this forum (R151519.EXE) and the same error at 59%. I have tried everything I have seen in the forums (closing virus software, editting setup ini file, etc) and I still get Update 778 error at 59%. I am running on an Inspirion 6000, CARD (CIRCUIT), IRELESS, MINI PCI CARD, 1370, BROADCOM CORPORATION, Dlink wireless router, windows xp with sp2, USA. I have also received an error that says something about internal setting incompatible (unfortunately I didn't capture the exact wording - I will attempt to recreate the error) This is terribly frustrating considering I was only following the dell suggestion that I update the driver and now that I attempted it, my laptop is sitting not being used.
My ASA 5510 IOS version 8.4.2 CSC IOS version is 6.6.1125,I configured ACLs and Class maps to forward all HTTP,HTTPS,SMTP,PoP3 and FTP taffic to CSC.Here my issue is my CSC not getting updating from the internet and some email sites like Webmail and Gmail are not taking forward after entering credintials. If i removed ACL belongs to the HTTPS , all are working fine( CSC updating well and all email sites are working.)
we recently updated all of our WLC's to 7.098 and it all went smoothly, controllers rebooted and AP's updated their firmware and rebooted OK.One WLC (4402) which was working fine since the update now has no AP's associated. The AP's were all configured to run in HREAP mode and are on remote sites within our WAN. I have checked that all policies and ports are still open (none have changed anyway) but the AP's can not join with the contoller.The log from an AP trying to join with the WLC.
[Code] .....
The logs on WLC show as below.
*emWeb: Jan 12 13:14:13.629: %AAA-5-AAA_AUTH_ADMIN_USER: aaa.c:1289 Authentication succeeded for admin user 'adann'*spamReceiveTask: Jan 12 13:14:12.919: %LWAPP-6-CAPWAP_SUPP_VER: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:21:a0:81:a4:10 supporting CAPWAP*spamReceiveTask: Jan 12 13:14:11.543: %LWAPP-6-CAPWAP_SUPP_VER: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:21:a0:81:8f:a0 supporting CAPWAP*spamReceiveTask: [Code] ......
BGP prefix list is not updated when other party having new downstream with different AS number.BGP filter has disabled but the prefix list is still not updated.BGP soft reset is performed, but the prefix list is still not updated.BGP prefix list is only updated when the other party having new prefix with the same AS number.Can explain why?
After updating driver Intel(R)82578DC Gigabit Network Connection my computer cannot find modem Experiabox from KPN (Netherland). Temporely solved by restore to the old version?
How do i download updated drivers for windows xp for another machine. I mean i have a 16GB stick .. but i have Dell computer that i reinstalled Windows Xp on it and i can't get onto the internet?
After not seeming to be able to save any configurations in 12.2(25)FX, I thought an upgrade would work since it said it didn't recognize my browser or OS but let me continue. I was able to see everything just couldn't save changes.
I updated to 15.0(1)SE3 and everything seemed to be going well. Tried to log back in HTTP (have not set n IP yet since it is still at my house... DHCP seems to be working) and I get a user/password screen that says level_15_access and it won't let me in.
Attempts to log in terminal have been unsuccessful. I can log in my dell switch which I am replacing and my APC units terminal just fine using USB to serial and Ubuntu.
I tried cisco as a password, user and password, admin, administrator no luck.
What is the best way to resolve this, is there a sure fire windows serial program or settings I should use in linux (currently 9600,8,N,1) to connect? I have looked through manuals till I am blue in the face.
We have a server connected to a 3560 switch which in turn connects to 6500s. The gateway interface is on the 6500. We will be changing the 6500s so the mac address for the gateway will change, however the IP address will remain the same. As we change out the 6500s the uplink connections to the 3560 will go down. This will flush the old mac address from the 3560.When the 3560 removes a MAC address does it update servers so they have to relearn the correct MAC address?
My internet (via wifi) works just fine. But here is the situation that has me baffled-I have a house that has ethernet wired ports in each room, then there is a central hub in my closet. In the hub, I have a grey ethernet cord that is labeled 'service'. This service wire connects to a board that features 12 ethernet ports, 1 of which says 'in', 1 says 'security interface' and has a little nub in it, and the other 10 are not labeled. The grey wire is in the 'in' port.So I am left with 10 ports- port 3 of 10 has a (phone cord size) cord in it, connecting into the 'line' port on my Qwest modem/router. (Qwest set this all up for me, by the way). The modem/router is obviously plugged into the wall. Now- remaining loose in the hub are 9 ethernet cords- 5 blue, 4 green. Each one of these is written on in sharpie, and has a room label on it. 'Family, living room, kitchen, etc...'. So, pretty obvious, I simply found which cord corresponds to the room I am trying to use (family GREEN is one, family BLUE is another). These 2 wires correspond to the top port, and bottom port of a switch plate that is in my family room. Now- inside the closet hub I plugged family GREEN and family BLUE into the back of the ROUTER, ports 1 and 2 (of 4 available). Now- I went back to the wall- connected ethernet wires into the wall plate and then into the ethernet devices I am trying to use (slingbox and directv dvr). Neither are working.
If I go to setup menu on dvr it says it cannot find a network, not getting an ip address. is that the slingbox red lights are both solid (which means there is a connection), and if I go back to the router ETH1 and ETH2 are lit up on the front, again implying that I have a valid connection. This isn't rocket science, but I must be doing something wrong. Are the family GREEN and family BLUE supposed to go into any of the 9 remaining ports that are open inside the closet hub? Because my thought was- let's say hypothetically I wanted to use every available wall jack in my house. There are 9 wall jacks total, but there are only 4 ports on the router. So this would not work. But, there are 9 ethernet ports open on the board in the closet. So I must need to use the ports in the closet, NOT on the router? If so, are these closet ports specific? Because (remember I have a phone like cord coming out of port 3, going into the 'line' port on my router/modem) I took this phone like cord out of port 3, plugged into port 4. and 5, and 6, 7, etc... and none of them would allow my wifi to work- the INT light goes off on the modem/router at that point. But when I plugged back into port 3 (where Qwest originally put it), INT lit back up and wifi worked again. So this makes me think that these 10 (9 remaining) ports are specific somehow? I know this was a lot to read. End result I am looking for- continue to use my wifi on the computer (the ONE place in my house there is no wall jack lol), and connect my slingbox and my directv dvr to the wall jack in my family room so I can (have slingbox) and get On-Demand content for directv.
everything in my home including my lap top has a signal. However, my desk top which I use my Belkin wireless USB adapter for, is not getting any wireless/ internet signal. This seems to have happened after a security update & restart of my computer.
I updated my Mac to OSX 10.8 and now every time I try to login to my work network (a windows network) it locks my account. Each time, my sysadmin unlocks my account and I am able to successfully login one time but then, if I login again (after restart or sleep) I am locked out.
when I was using image 1.0.0.27, I was able to move the management VLAN from 1 to which ever VLAN I wanted. For some reason, after switching the image to 1.1.1.8, I no longer have that function.
