when I was using image 1.0.0.27, I was able to move the management VLAN from 1 to which ever VLAN I wanted. For some reason, after switching the image to 1.1.1.8, I no longer have that function.
View 1 Replies
End user have had problem with IP phones that are connected to 3750 stack; many times IP phones lose connection with CallManager and the only way to clear this issue is with clear arp command. DHCP for IP phones is configured in 3750 stack.
At the beginning 3750 stack was set a VTP server, and the others as VTP clients, we detected another VTP server switch so we thought that was the problem, but after removing the issue remains. Finally we set all switch in transparent mode.
Base on this we decided to change the software image 12.2(35)SE1 C3750-ADVIPSERVICESK ---> 122-53.SE2 IPSERVICES I'm going to follow the procedure 3750 Series Switch Stack IOS Upgrade − Automatic .
as it show in the following information there are 4 differents models of 3750 switches, I have already download c3750-ipservicesk9-tar.122-53.SE2.tar for 3750G-24TS.
I have two doubts:
1. There is no problem for using this tar file for all models?
2. I followig command is correct for the change I plann to do ?
Switch#archive download-sw /allow-feature-upgrade /overwrite tftp://192.168.0.24/c3750-ipservicesk9-tar.122-53.SE2.tar
#sh inventoryNAME: "1", DESCR: "WS-C3750G-24TS" 16MB Flash 128 DRAMPID: WS-C3750G-24TS-E
[Code].....
it says that the cisco sg300-28 managed switch default system mode is Layer 2. but i want to change it to layer 3.
i can't get inside the "Console Interface Main Menu" where the switching from L2 to L3 will be done.
I have done the ff:
1. Upgraded firmware to 1.1.2.0 (latest)
2. Reset the switch to factory defaults.
3. The guide stated that in order to perform telnet to the switch, you need to enable it. So I logged in first in to the web GUI and enable telnet service.
4. I can now start telnet on the switch but I can't see the "Switch main menu".
All I can see are these lines from telnet:
User Name:cisco
Password:******
switchd5928c#
I just want to know how to get into the console interface main menu where these lines should appear so that i can change the system mode:
• System Configuration Menu
• Port Status
• Port Configuration
• System Mode
• Help
• Logout
I am planning to change the management IP (VLAN 5) to one of my Cisco 2950 switch, Here I am creating a new VLAN101 and assign new IP
When I am doing this VLAN 2 is going admin down.
Apparently on older switches you could just enter the "management" command under the new VLAN interface and it would pull the config from the old one, apparently that feature isn't around anymore. I've tried establishing a trunk to the damned thing and trying to switch over that way, but it doesn't seem to work.
View 4 Replies View RelatedI recently set up a small photography business and am trying to get a Cisco 877 and Cisco SG300-10 switch to talk to each other.
What I want is for the Cisco 877 to handle the internet and the SG300-10 to handle the local network,
I have set up 2 vlans in trunk mode on the switch and want vlan2 to manage local traffic and vlan3 to handle the internet.
I have got the 877 connecting to the internet what I dont have, traffic going to vlan2 on the switch from the 877
Look at the running configs for the switch and the router and tell me how to get the vlan on the router to pass traffic to the switch. In a nutshell I am inserting the internet into the switch but am not sure how to progress. I have the c870-advipservicesk9 image file on the router.
Switch Config
interface gi2
description connection-to-data-vlan
exit
interface gi3
description connection-to-internet-vlan
exit
vlan database (code )
We've got a SG200-18 switch that is to be used as a workgroup switch in our environment (SW Version 1.1.1.8). Working with CLI on big and mid-range Cisco-gear over the past two decades I'm having a hard time figuring out the following on the SG200:
o) I want to change the Management-VLAN from the default "1" to the management-VLAN used in our environment. Sure enough I created that vlan in the SG200-config, however when it comes to assigning the management-IP and VLAN for the management interface in the corresponding pulldown under "IPv4 interface -> Management VLAN" the only thing selectable is the default "1". (see screenshots enclosed)So how do I set a management VLAN different from 1?
o) How do I enable telnet/ssh-access to the SG200-18 - I'd be far more comfortable with a CLI-environment?
i have a small network with Polycom phones connected to the sf300 switch and have the pc's daisy chained via the second switch port on each phone. i have the pc traffic running on the default vlan 1 and the voice traffic running on the voice vlan 100. can i do bandwidth management on a vlan/port basis or is that not necessary. i want to ensure that the voice traffic is never impacted by the pc traffic on the same cable.
View 2 Replies View Related spam up the boards with the same basic CCNA level stuff, but I have a couple of questions about ios differences, limitations, and references. I have the following three switches. One appears to be considerably dated in regard to software version. My confusion/ignorance stems from managing VTP settings.
2924XL 12.0 5 WC8
2950 12.1 22 EA6
2950 12.1 22 EA6
When I set either 2950 switch as the VTP server, and the other as a client, the client inherits the server settings as expected. However the 2924 requires that I go into the vlan database from priv exec and manually set vtp client. That's pretty similar to setting any switch to client mode. The problem I am observing is that after setting the 2924 to client, it still doesn't inherit vtp version settings or pruning settings. I still have to manually configure those. Additionally, if I copy run start the 2924 after making these manual settings, and then reload the switch, all the settings are lost and it defaults back to server mode with all features disabled. From my searches, it looks like vlan information is stored in vlan.dat, but all the documentation I've found is on 12.1 ios which doesn't appear to use vlan database for vtp setup, meaning it might still be an issue, but not one I'm focused on at the moment.
Is the vlan database dumped at reload? I've read vlan.dat is stored in nvram and should be saved after a copy run start, but that is not the case for me.I have since set the 2924 as the server, manually configured the server from vlan database, executed copy run start, and reloaded the switch. Oddly, my manual settings saved from the reload, meaning I only lose settings when the switch is in client mode.Am I missing additional necessary client commands to save the config, or is this just a limitation of either the 2924XL or the 12.0 ios?On a related but completed out of scope topic, without a cisco service contract, how am I supposed to make heads or tails of all the different versions of ios, along with the letter-based features and what-not? I can't even find my 2924 in the list of platforms when searching for ios upgrades.
I'm trying to figure out how to (or if I can) setup the management interfaces (fa1) on a couple of new 4500X switches. My issue is that the 4500X's themselves are the gateway for my management VLAN (.1 HSRP virtual, .2 and .3 SVIs on the pair of switches).
I would like to assign addresses from the management VLAN to the router Fa1 management interfaces but the software configuration guide seems to note this is not supported (and indeed it doesn't seem to work).
Physically I have Fa1 from core-1 into a port on an adjacent switch. Fa1 from core-2 also goes into a port on that adjacent switch. Both are in my management VLAN, whose SVIs are on the cores themselves.
I just got my Cisco SG300 28, but I have some problems getting the routing to work. I get the vlans to get to the router, with the default route. But not getting them to talk with each other. I can ping the IPs from the cisco, but I am not getting traffic to go from vlan 1 to vlan 2. When I try to google, it say that it should do it automatically, and I found no setting for it. It looks like it not creating any route for the interfaces.
View 2 Replies View Relatedi am first time to trying to make Vlans. I managed to do 2 vlans to SA520 to ports 1 and 2. But when i try to separatethem to SG300 with web management it doesnt work. Vlan 1 works fine, i untagged wanted ports and forbid vlan 2 ports.In Vlan 2 there vice versa, is this right way to do? Both Vlans has their own DHCP range as i do them to SA520.
View 2 Replies View RelatedI have 2 SG300 switches, in layer3 mode, lag'd together for high availability, serving 2 Dell R815's and a Dell Equallogic 4100 for virtualisation. I have setup a number of vlan's, network traffic, mgmnt traffic, iScsi, vMotion etc and they seem to work.
However, Equallogic unit suddenly became unavailable to view for managment yet maintained iscsi traffic for the servers ok. After much head scratching, noticed that one of my SG300's had the vlan ports assigned to various vlans had *automagically* changed there assignment, ie tagged changed to excluded, but only for one of the iscsi traffic connections and the mgmnt port, both coming from the Equallogic, the other iscsi continued its assignment fine. The other SG300 hasn't changed. Guaranteee no one has been into change it and no changes have been made to Dell servers or Equallogic.
Q. Is there any circumstance where the switch can change the port setup itself? or is there any external circumstance that would trigger that change either?
This has now occured twice. The setup is running as a test lab, not in production until all setup is complete, then it will replace our existing harware.
Randomly when I try to access to 2950 from management tools, switch is unreachable, I have to access from other switch and reload 2950.
Problem only is from managemt tool to managament vlan 1 2950.
The strange thing is that management interface is encountering a very fast increase of throttles, broadcast and ignored packets:
2950#show interfaces vlan 1
Vlan1 is up, line protocol is up
Hardware is CPU Interface, address is 0023.3488.fd65 (bia 0023.3488.fd65)
Internet address is xxxxxxxxxx
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
[code]....
It could be a hardware problem?, IOS has been upgraded.
Any snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies View RelatedI have a question regarding SG300 series small business switches.If I switch between the two possible images, will the configuration get lost or is the configuration the same independent of which image I choose?
View 1 Replies View RelatedI have several closets with Cisco 3560 on the edge that I'd like to change the vlan that's used for the management vlan on each. In the core I have a Cisco 6509 with Sup720's.
I'd like to do this by changing the native vlan on the trunk port on the core 6509 interface that connects to the 3560. and leave the management vlan on the 3560 as vlan 1.
Seems trivial but what I tried didn't work and I didn't have the window to troubleshoot. I'll paste the simplified configs for the interfaces below
!
6509 configs:
!
interface Vlan50ip address 172.16.50.2 255.255.255.0!interface FastEthernet
[Code]....
I'm trying to change a vlan on a port-channel but I am getting this error when I apply the change:" error: command is not mutually exclusive",I have done this in the past but I cannot remember exactly what I should type to apply the change.
View 2 Replies View RelatedI want to setup VLAN with the switches SG300 and SLM2024. What is the suggestion to connect these 2 switches. We have the Juniper net screen.
View 1 Replies View RelatedThere is new firmware for the B series of the Dir-825 but the change log is not updated.
View 10 Replies View RelatedWe have recently purchased a SG300 to break up our network which most consists of virtual machines via Bridged networking on network machines. I have created successfully Vlans and the physical machines are capable of communicating across the different subnets that I have created via the SG300 however the Virtual machines can no longer be reached.
View 2 Replies View Related i was trying to set up a new SG300-52 L3 switch for switching and Vlan. The problem is that the vlans on this switch cannot get their DNS resolved. Probably a stupid thing i can't get to see, but i think it is a simple solution given switchin is not my expertise.So my setup:
- ISP Wan router: LAN ip 10.0.0.1, DMZ: 10.0.0.2 -> i have to use this router for ISP support. But it suckes, that's why we use own router for firewall, port forwarding etc.
- Nice Router: WAN: 10.0.0.2, LAN: 192.168.1.1
- SG300 L3 switch
This works. I can ping switch, nice router, ISP router and google's ip from VLAN 5.But i cannot ping google using host name. From within SG300 i can. So it has something to do with SG300 not doing DNS right.My Client on VLAN 5 has ip 10.1.1.5 / 24, default gateway and dns pointing to switch: 10.1.1.1.I have put an entry in DNS servers in SG300: 192.168.1.1 active (pointing to Nice router). On client leave default gateway pointing to switch. But put DNS server : 192.168.1.1
I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies View RelatedI have a connection on IP 192.168.1.21, Subnet 255.255.255.0 - this is on the default VLAN1 on the switch. I need to route this to IP 10.0.3.101, Subnet 255.255.252.0 - which is set up on VLAN2 on the switch. I have set the switch to Layer 3 via console.
how I setup this route? I am use the Browser based interface.
configure my new SG300-28P. When I have started the switch, I have specified a new password and enabled telnet in order to setup the switch in Layer 3 mode.
After a restart, the switch took its IP address from a DHCP server. When I try to set a static IP address (192.168.2.1), I receive the following error message: Duplicated IP interface on the same subnet.
The IP address 192.168.2.1 is not used by any device within the network. For information, the message doesn't appear when the switch is in Layer 2 mode.
why I can't change the IP address of default vlan in Layer 3 mode ? All I can do is set the IP address to static or dynamic.
For test purpose, I have added 2 vlans. But I wasn't able to route traffic between vlan. how to configure the switch to route traffic between vlan?
find below details informations about my VLANs.
- Default (VLAN ID 1)
IP Address : 192.168.2.1
Subnet : 255.255.255.0
[Code].....
After not seeming to be able to save any configurations in 12.2(25)FX, I thought an upgrade would work since it said it didn't recognize my browser or OS but let me continue. I was able to see everything just couldn't save changes.
I updated to 15.0(1)SE3 and everything seemed to be going well. Tried to log back in HTTP (have not set n IP yet since it is still at my house... DHCP seems to be working) and I get a user/password screen that says level_15_access and it won't let me in.
Attempts to log in terminal have been unsuccessful. I can log in my dell switch which I am replacing and my APC units terminal just fine using USB to serial and Ubuntu.
I tried cisco as a password, user and password, admin, administrator no luck.
What is the best way to resolve this, is there a sure fire windows serial program or settings I should use in linux (currently 9600,8,N,1) to connect? I have looked through manuals till I am blue in the face.
We have a server connected to a 3560 switch which in turn connects to 6500s. The gateway interface is on the 6500. We will be changing the 6500s so the mac address for the gateway will change, however the IP address will remain the same. As we change out the 6500s the uplink connections to the 3560 will go down. This will flush the old mac address from the 3560.When the 3560 removes a MAC address does it update servers so they have to relearn the correct MAC address?
View 4 Replies View RelatedMy organization wishes to host a LAN gaming event. The setup I have in mind involves a 24-port switch for connecting all the player computers and having that switch connected to a smaller "core" switch which has the the game server and router connected to it. I'd like to know if I can set things up as follows...
SG200-26 with ports 1-24 on seperate VLANs so they cannot talk to eachother. I'd then like ports 25 and 26 to be an aggregated (for bandwidth and redundancy) trunk port to carry all 24 VLANs plus an additional management VLAN (ex. VLAN 100) that will be used for accessing the switch. I'd like those aggregated trunk ports to connect to an SG300-10 "core" switch which will be connected to the game server and to a router for internet access.
I'd like the ability to have two network connections from the game server to the switch, one on the management VLAN and one on a different VLAN (ex. VLAN 50) that will be accessed by the players (ports 1-24 on the SG200-26). The core switch needs the ability to perform restricted inter-VLAN routing, in that it doesn't allow VLANs 1-24 to talk to eachother but they can talk to the server's VLAN but only through specific service ports (ex. port 12345, 12346). Is this possible?
Furthermore how would I configure the SG300-10 to allow VLANs 1-24 to talk to VLAN 50, but not themselves or VLAN 100. As well, I'll probably have the router on it's own VLAN (ex. VLAN 60) and allow VLANs 1-24 to access it but only through HTTP port 80 for web access.
I have a Netgear GSM7248R switch with 5 different Vlans including th management Vlan. Each of the vlans are connected to my layer 3 switch for routing. I want to access the management vlan form any of my Vlans so my layer two switch can be detected by my snmp manager.
View 3 Replies View RelatedI have a SG300 switch working in layer 3 mode. I created 3 VLANS and the intervlan communication is working fine. I want to know how to block acces to switch managment from the Vlans. One of the vlan is allowed to access the switch but not the others vlans. What is the best way to implement this? with ACL or with Managment Access Method, creating an access profile?
View 1 Replies View RelatedI have a new SG300-28P, and have had occasional issues with being unable to connect to it via anything other than the serial port. I have connectivity between my machine and the switch (tested with ping each way), and in fact, have the same problem if I take a laptop to the switch and connect them directly.What happens is that though the switch is operating normally, http, https, ssh and telnet attempts to access all fail in one way or another. Ssh and telnet either yields no response or a refused connection (even though those services are enabled). For http and https, I'll occasionally get enough of the web page to be able to tell what it is ... but attempts to log in just don't work.While this is happening, the CPU and packet load on the switch is very, very low.Rebooting didn't work entirely, though it may have made it better. Resetting to factory defaults and then reconfiguring makes it work.This is using the latest firmware: 1.2.7.76.
View 3 Replies View RelatedWhat tools are you using to manage multiple SG300 in a single network ? I can't find any good solutions on the cisco website.
View 1 Replies View RelatedHow to set the management interface on a SG300 Switch in Layer 3 mode? I've some vlans configured on the switch with interfaces in each of them:
Vlan 100 (10.0.1.254 /24)
Vlan 200 (10.0.2.254 /24)
Vlan 300 (10.0.3.254 /24)
...
Vlan 900 (10.0.9.254 /24)
Now, the management interface is listening on all interfaces (IPs). But I would like to configure the switch to only listen on 10.0.9.254. What I need to configure or whether it is possible?
