Cisco Switches :: SG 200-18 - Change Management-VLAN And Telnet / SSH Access?
Apr 29, 2012
We've got a SG200-18 switch that is to be used as a workgroup switch in our environment (SW Version 1.1.1.8). Working with CLI on big and mid-range Cisco-gear over the past two decades I'm having a hard time figuring out the following on the SG200:
o) I want to change the Management-VLAN from the default "1" to the management-VLAN used in our environment. Sure enough I created that vlan in the SG200-config, however when it comes to assigning the management-IP and VLAN for the management interface in the corresponding pulldown under "IPv4 interface -> Management VLAN" the only thing selectable is the default "1". (see screenshots enclosed)So how do I set a management VLAN different from 1?
o) How do I enable telnet/ssh-access to the SG200-18 - I'd be far more comfortable with a CLI-environment?
View 2 Replies
ADVERTISEMENT
Jan 20, 2011
I have a Netgear GSM7248R switch with 5 different Vlans including th management Vlan. Each of the vlans are connected to my layer 3 switch for routing. I want to access the management vlan form any of my Vlans so my layer two switch can be detected by my snmp manager.
View 3 Replies
View Related
Aug 2, 2012
Apparently on older switches you could just enter the "management" command under the new VLAN interface and it would pull the config from the old one, apparently that feature isn't around anymore. I've tried establishing a trunk to the damned thing and trying to switch over that way, but it doesn't seem to work.
View 4 Replies
View Related
Aug 7, 2011
Any snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies
View Related
Nov 21, 2011
when I was using image 1.0.0.27, I was able to move the management VLAN from 1 to which ever VLAN I wanted. For some reason, after switching the image to 1.1.1.8, I no longer have that function.
View 1 Replies
View Related
Nov 29, 2011
I just purchased 2 SF-300 48 port units for 2 customers. I want to be able to remotely manage them over the Internet with my browser. BUT, customer sites already use port 80 for web servers. So, how do I configure this switch to use some other port than 80?
I called support, and much to my surprise he said it cannot be changed. How bizarre that a device with many hundreds of configuration settings does not have one of the most basic settings...
At one customer site I can configure port forwarding and translation to get around this problem, but the other site's router does not offer port translation..
View 2 Replies
View Related
Mar 12, 2013
In one of my client location I have deployed one Cisco 3560X (core switch) and one SG-200-18 (access switch). I’ve configured three vlans (vlan 2, vlan 3 and management vlan 1), relevant trunking and I’ve connected two pc to the access switch to vlan 2 and 3 respectively. So far everything (including inter-vlan communication) works fine, except that I couldn’t reach the vlan 1 (management vlan) devices (access switch and core switch) from any pc which is connected to either vlan 2 or 3.
I’ve configured the “port VLAN membership” settings in SG-300 as follows,
Interface mode Administrative vlans Operational vlans
GE 2 Access 2UP
[Code].....
View 4 Replies
View Related
Oct 12, 2011
I got question about Cisco SF300-24P- is it possible to have management vlan in other vlan than in default vlan?I have default vlan 10 and voice vlan 20, I need to reach switch through voice vlan so I need to set up, interface vlan 20 with ip address. I ask these, because in gui, under Management Interface, IPv4 interface,under Management VLAN, I can only choose vlan 10, which is my default vlan, I dont have option to set ,up, in this case, vlan 20 as management vlan.
View 2 Replies
View Related
May 15, 2013
I want to remotely access Cisco 500 switches via TELNET and WEB BASED from a server. I dont know the ip addresses for Cisco 500 switches which are configured as backbone which the ip address assigned on the network is static ip address. Specifically I want to get their configuations inorder to get their specified assigned vlans on the network. I know the ip addresses for their specified cisco 500 switches' gateways. I know that cisco 500 switches can be accesses through web. Is there other ways to solve the problem apart from going onsite and connect to the cisco 500 switches using network cable since cisco 500 swithes dont have console ports?
View 1 Replies
View Related
Jan 21, 2012
I have an HA ACE deployment and all seemed to be working well until I tried to access the ACE via the management VLAN in the one non-system context, no go.The ACE is in one-armed mode with an Admin/System context and one user context (named Messaging). Source NAT has been set up in the user context. All VLANs are in a port channel back to the core switches.I can access the ACE via the Management VLAN in the system context, all OK. I can access the load-balanced servers via the VIP in the user/Messaging context, all OK. I CANNOT acccess the managment VLAN other than ping it (resonds to ping, but telnet, ssh, https, etc. fails).The system/Admin context has a default route to the Management VLAN on the core. The User/Messaging context has a default route to the core switches on VLAN 5, which is the VLAN where the VIP resides.If I change the default route in the User/Messaging context to the Management interface on the core switches then I can access both contexts for management, but then the load-balancing falls over and I cannot access the serverfarm (via the VIP). Traces on the rservers show that NAT is being hit on the ACE and the requests are coming from the real IP of the clients. Put the default route back to the User/Messaging VLAN on the core and NAT is back to what it would be expected to be, and then remote/management access to the ACE is gone.
ACE02/Admin# sh run
Generating configuration....
logging enable
logging standby
logging timestamp
logging buffered 4
logging device-id context-name
[code]....
View 1 Replies
View Related
Jun 8, 2011
I've got an ASA 5505 running 6.3 I've connected the management interface to our management vlan (which contains switch IPs, ilo's etc)Is there a way to allow access to this vlan from another?
View 1 Replies
View Related
Mar 25, 2012
I have a SG300 switch working in layer 3 mode. I created 3 VLANS and the intervlan communication is working fine. I want to know how to block acces to switch managment from the Vlans. One of the vlan is allowed to access the switch but not the others vlans. What is the best way to implement this? with ACL or with Managment Access Method, creating an access profile?
View 1 Replies
View Related
Jul 12, 2012
I am the Systems Admin at LDM Media and am trying to get some support for one of the SRW224G4 managed switches we have in our rack. The issue is as follows:
Any endpoint connected to the switch is assigned an IP address in the range of 169.254.154.XXX regardless of the switches set IP range, the second issue is that I cannot access the web view management interface through the default IP address 192.168.1.254 (and I have tried to use the last IP in the range set by the router 169.254.154.254, to no avail)
How to regaining control of this supposedly smart switch?
View 3 Replies
View Related
Dec 18, 2011
I have Cisco router 851 at my region site. It has five Fa ports. One of them is connected to ISP and has ip address 10.1.1.2 (for example). It also has vlan 1 interface, that has ip address 192.168.0.1 (also for example). I also have Tun0 interface that goes through ISP network and connects to my hub network. The rest of Fa interfaces are swithcable and they are in vlan 1.The problem is that from hub LAN I can telnet to 10.1.1.2 ip address, but I can't telnet to 192.168.0.1. Whereas I can Ping 192.168.0.1 from my hub LAN.
Topology:
Hub LAN -------ISP---------Spoke Router 851
View 8 Replies
View Related
Jan 15, 2013
I recently bough for a home lab a sg300-10 switch. I have enabled layer 3 routing on it and have come across a puzzling issue. The switch is the default gw on this network, and in front of the switch there is a cable modem (ip route 0.0.0.0 0.0.0.0 192.168.0.7).
This is my config:
config-file-header
switch5ed948
v1.2.7.76 / R750_NIK_1_2_584_002
[Code].....
View 7 Replies
View Related
Jun 17, 2011
how do i change the telnet and enable and vpn user password on asa 5570.
View 4 Replies
View Related
Apr 17, 2011
I’ve recently brought a SG 300-52 for my company with the main intention of using the L3 switching, I’ve recently gone on a 3day cisco course and came backing thinking i knew what i had to do but as always if you don’t have the experts next to you to answer the questions you soon have problems.
I have setup 3 VLANS, the switch is basically on its default settings and VLAN 1 connects straight to the router/gateway and on the internet but VLAN 2 and 3 do not, they are completely localy contained to their own Non DHCP networks.how do I get VLAN 2 and 3 on the internet and able to talk to each VLAN?
The keywords I’ve came across in my search are static routing between VLANs and InterVLAN, I’m assuming i need to do one of these??
View 26 Replies
View Related
Apr 17, 2013
i have a asa5505 and sf300-48,in the sf300 have ip defult-gateway 192.168.1.93 and have internet in vlan2 but vlan 3 not work. ping from "vlan3" to "vlan2" its ok.
View 5 Replies
View Related
May 9, 2012
I start writing this post telling you that I'm not a qualified network admin, so I beg your pardon if I do not use appropriate terms in my question. Also my english in not so good since I'm Italian and my english in almost scholastic.
This is the "story" :
I bought two switches as described above and actually I have to create 2 VLANS as described below :
VLAN id 2 name "Service_A" ports 1-4
VLAN id 3 name "Service_B" ports 7-9
all other ports can stay in default VLAN1.
my network infrastructure have some other very simple swtiches connected and 1 soho router (static ip 192.168.1.1) with dhcp active and ip pool address released from 192.168.1.100 to 200.
the SG200-26 have static ip 192.168.1.254 and 192.168.1.253
MY NEEDS:
I need VLAN for privacy matter so all computer connected to ports in VLAN2 cannot see nor enumerate PCs and resources on other VLANs, but I also absolutely NEED that all computer in every ports (and every VLAN even default VLAN1) can access the internet.
View 1 Replies
View Related
Sep 25, 2011
I want to change the management IP of our wireless controller, I have 5 LAP1142N connected to this controller.
I have a few questions before I will do this task.
1. If I change the management IP, will the controller need a reboot?
2. Will the AP's automatically sync with the new management IP?
3. Do I need additional configuration on the AP's?
4. What else do I need to consider.
View 9 Replies
View Related
Jul 31, 2011
I'm trying to change the management IP for ACS 5.2 in GUI, but failed to find it.
Is there any way to change the IP address in ACS GUI?
View 3 Replies
View Related
Nov 7, 2011
I have a Dell switch setup with 2 Vlan's. Vlan 1 is to the network. Vlan 20 is going to be for wireless access to the internet. How do I configure the switch/router so that Vlan 20 only connects to the internet and not the network? I will later want to have a 2nd SSID that I want to connect to both the internet and network.
View 5 Replies
View Related
Apr 10, 2013
What is VLAN Management
View 4 Replies
View Related
Sep 1, 2011
I have two 5508 and one WCS server, the controllers are in one mobility group.Now I have to change the management IP addresses on the controllers. What are the correct steps to do this?
View 9 Replies
View Related
May 19, 2012
I have more than 20 SF 300-24P 10/100 Managed Switch switches deployed and running in my office network. All these switches have web configuration utility enabled. We would like to enable telnet too. But for this I know I have to visit site to site, connect the switch manually with a laptop and enable telnet option. I am looking for how can I enable telnet in these switches using web-based switch configuration utility.
View 3 Replies
View Related
Nov 4, 2012
I am planning to change the management IP (VLAN 5) to one of my Cisco 2950 switch, Here I am creating a new VLAN101 and assign new IP
When I am doing this VLAN 2 is going admin down.
View 3 Replies
View Related
Jan 14, 2012
I have sf300, i didn't found the option to telnet it. default IP of the switch is 192.168.1.254, i can access it by HTTP.
also i'm not able to attach IP phone on voice vlan & computer on vlan 1 ,please share the step by step guide how to access the switch by telnet.
& how to make voice vlan 2 for IP Phones & Vlan 1 for PC.
View 3 Replies
View Related
Mar 14, 2011
I can telnet to switch from checkpoint firewall access port and from switch directly. I can ping/traceroute successfully to the switch. Access-lists 14 & 15 are allowing the traffic I want. The router on the other side of the FW has 2 static routes and a default static route set up.
Here is some of the config from my switch:service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryptionhostname xxxxx
enable secret xxxxxx
username xxxxxxxx password xxxxxxxip domain-name xx.xx.netaaa new-model
aaa authentication login default local enable line none[code].....
Not sure of checkpoint firewall config....I have run wireshark when trying to telnet and I get no syn-ack back from remote switch. Just 3 consecutive syn attempts.I have some switches I can connect to and they go right through the 3 way TCP handshake and I cannot find any differences in the configs between the successful connections and the unsuccessful connections.
View 1 Replies
View Related
Jun 29, 2011
Can I change the untagged vlan on a 1131 to a new vlan. I need to move my management vlan from 10.1.1.1 on vlan 1 , to 172.16.0.1 on vlan 200. I attempted several configuration options including removing the vlan1 ip, changing my new vlan200 to untagged and mirroring it on the switch, and adding my new ip to vlan 1 untagged and then untagging the switch with access vlan 200 on the connected port. Nothing worked.
Below is a sample of what I changed:
interface Dot11Radio1
no ip address
no ip route-cache
[Code]....
View 1 Replies
View Related
May 10, 2012
We are installing a 2504 with management on VLAN2. The management port is on interface 1 which is attached to a layer 3 3750. From other VLANs in the network we cannot manage the 2504 controller with the web manager. We are running the latest code, 7.2.103.0, since we are using 3600 APs. We have a TAC case open, but spent 3 hrs with them and they can't figure out the problem. TAC did some debugging and saw that the 2504 is ARPing for the address of the PC on the other VLAN instead of sending the packet to its default gateway. How to get success with the management interface on a VLAN and managing the controller from another VLAN?
View 2 Replies
View Related
Mar 17, 2012
I'm doing some tesing in SFE2000P linksys switch about the TACACS authentication. I have configured the switch accodringly to point my ACS server with key string. Now, I'm able to login into the switch with TACACS account in HTTP/HTTPS only and but, not with the TELNET access.
Still Switch is authenticating with the local user account only, when in TELNET access method.
View 6 Replies
View Related
Nov 12, 2012
configure Line Telnet on a Cisco SG300-10P switch.I am in config mode and enters line telnet,but when I do a show line,telnet still are disabled..
View 1 Replies
View Related
May 21, 2012
I have an SG300 authenticating telnet login to a RADIUS server. It allows me to log in at Priv level 1. when I try and enter Priv 15 mode, I'm prompted for a password which I don't appear to be able to set anywhere or know.
If I remove RADIUS and go back to Local authentication, telnet logs me in at Priv15 immediately.
View 3 Replies
View Related
