Cisco Switches :: Configure Line Telnet On SG300-10P?
Nov 12, 2012configure Line Telnet on a Cisco SG300-10P switch.I am in config mode and enters line telnet,but when I do a show line,telnet still are disabled..
View 1 Replies
ADVERTISEMENT
Cisco Switches :: SG300 - Telnet And RADIUS Authentication
May 21, 2012I have an SG300 authenticating telnet login to a RADIUS server. It allows me to log in at Priv level 1. when I try and enter Priv 15 mode, I'm prompted for a password which I don't appear to be able to set anywhere or know.
If I remove RADIUS and go back to Local authentication, telnet logs me in at Priv15 immediately.
Cisco Switches :: How To Configure Two Links Between Switches SG300
Apr 22, 2012I have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?
View 2 Replies View RelatedCisco Switches :: How To Configure SNMP On SG300 Using CLI
Feb 3, 2013how to configure SNMP on the Cisco SG300 switches? I have the SG300-10P. I am not fully familiar with the new command line interface on this device, it was easy on the IOS but finding it a nightmare on this one.
I put the following command in but it didnt work.
snmp-server view Interfaces interfaces included
snmp-server community ACB123 ro 10.x.x.x view default
I tried to follow the guidelines on the cisco website but thats all Web interface based, i can only access the switch remotely via CLI.
Cisco Switches :: How To Configure Sg300 28 For Vlan
Feb 19, 2013i purchased 300-28 how it config for stp and trunk
View 2 Replies View RelatedCisco Switches :: To Configure Port Forwarding On SG300-20
Sep 17, 2011I have a Cisco SG300-20. I have read the documentation and cannot seem to locate the instructions for port forwarding. I need to forward TCP port 8088 to IP address 192.168.14.110 on the switch.
View 5 Replies View RelatedCisco Switches :: Configure SG300 Intervlan Routing?
Apr 18, 2011Some tips and trick on how to configure and sg300 for intervlan routing.
I already have the switch set up for layer 3 I already set up multiple vlans and each vlan has a ip interface setup with the desired subnet I see the local routes set up in the static routing page.
I cannot seem to get from one subnet/vlan (I am using one subnet for each VLAN) to the next.
Cisco Switches :: SG300 To Configure VLAN Rate Limit
Apr 14, 2013I have a Cisco SG300 small business switch and 541 APs. There are 2 VLANs in our network. One must be limited by bandwidth. How to configure vlan rate-limiting on SG300? And describe CIR & CBS.
View 1 Replies View RelatedCisco Switches :: Configure SG300-28 Router By Multi-Vlan?
Mar 22, 2012why i can not found ip router setting by main menu? the sg300-28 can not support ip router command?mor informations,see my img. If sg300-28 can not support ip router command,what i can do it that communicate by multi-Vlan ?
View 2 Replies View RelatedCisco Switches :: Configure Port To Connect SG300 To 3com Unmanage Switch?
Apr 1, 2012I have my network with severals SG300 switches.I have one of them like my core switch working in layer 3 mode. With 2 vlans and vlan interfaces to each vlan.Everything is working ok.But now i have to connect one 3com unmanage switch that have host from vlan 1 and 2. How should i connect this switch to my Cisco sg300 switch?
[code]...
Cisco Switches :: SG300-28 GUI Different Than Online SG300-48 Simulator
Aug 29, 2011These are our first switches and seems like GUI is lot different than the online. Out intervlan routing is o not working. I am absolutely sure that I setup the switch in L3 mode since it allows me to create mutiple interfaces. I am hoping that this GUI issue is related to interVLAN routing.
Below is the blog I started for InterVlan issue [URL]
This is the link for online simulator and what I see in its IP tab. I know this switch is not SG300. [URL]
This is what I see on our switch.
Our switch version
switchd64684#show version
SW version 1.1.0.73 ( date 19-Jun-2011 time 18:10:49 )
Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 )
HW version V01
Cisco Switches :: SG300-28P And SG300-52 Web Managing - Fans
May 26, 20111) I have a Cisco SG300-28P. I plan to add a SG300-52. Would it be possible to manage the new switch through the SG300-28P web browser ?
2) There are 2 fans in the POE model SG300-28P. How many fans are they in the non POE switch SG300-52 ?
Cisco Switching/Routing :: 2911 - Capture User Who Execute Telnet / Show Line In Log?
Jan 21, 2013We are running in our DC one of the CISCO 2911 terminal server which is connected with HP ARC sight logger.
it is possible to capture user who execute ‘Telnet” or “show line” in the log, I mean all the command entries by user.
How to enable any config on 2911.
Cisco Switches :: SG300-28 Uplink To Another SG300-28?
Feb 8, 2012Can I connect a single Cat5e cable between two SG300-28 and link them? If so what must I configure?
View 1 Replies View RelatedCisco Switches :: Difference Between SG300-28P And SG300-52
Jul 25, 2012I have SG300-28P that I am using as layer-3 switch. Recently I ran in to SG300-52 switch and even though loading same firmware doesn't give me option to do layer-3 switching. For SG-300 I see options in GUI to create vlan interfaces under IP information section, while SG300-52 has IP information option only under the management section.let me know if these are 2 different hardware types and L3 is not possible on SG300-52. If its possible to enable L3 switching on SG300-52?
View 2 Replies View RelatedCisco Switches :: No Command Line Interface On SF200 Small Business Smart Switches?
Sep 20, 2012we just received 5 new SF200-48 Smart Switches for small business. I noticed only way I can configure them is by using the web gui. Is there a way to enable good old CLI?
View 6 Replies View RelatedCisco Switches :: Replacing 3COM 4500 Switches With SG300-52?
Nov 21, 2011I'm replacing 2 3COM 4500 Swithes with the SG300-52 Cisco switch. We have 3 VLANs, 10, 20, 100. The switch is set for Layer 3 and I have setup DHCP relay. what settings i should set on the Cisco for the following setups:
3COM Setup
#
interface GigabitEthernet1/0/1
[Code].....
Cisco Switches :: SG300 Switches Have Poor Performance In Layer 3?
Jan 1, 2013We have several of the SG300 Serices switches. We use them to route VLAN traffic to Remote Offices, Internet Connections, and WiFi Access Points.In one remote office we have a SG300-10 setup to route the HQ Network and the remote Office Subnet. The SG300 is Connected to HQ via Fiber and has multiple Tagged VLANs on it. If I do speed tests over the Fiber Link on the Incoming Tagged Netwotk I get Decent performance, 80Mbs. If I switch to a networtk that is not priginating from HQ, and have the SG300-10 route packet, I get dismal performance. 15-20Mbs.
I Fireded up a New SG300-28P FW v1.2.7.76. Added a the HQ VLAN 101 and new VLAN 1025 . Mapped some Tagged and untagged ports for each. Switch was connected to HQ Network as untagged VLAN 101. I put a laptop on an Untagged VLAN 101 port. Ran some tests, cam back with 750-850Mbs. Great. Put the same laptop on a Tagged 101 Port, Configured the NIC for Tagged VLAN 101, Same test, same Speeds, 750-850Mbs.I then Configured laptop for Tagged VLAN 1025. Connected to tagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!
I then Configured laptop for Untagged VLAN 1025. Connected to unagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!It was only the Laptop and the Connection to the HQ net on the SG300-28P. Why is the performance of this unit soooooo poor when it needs to route?Other Switches have FW v1.0.0.27 or FW v1.1.2.0. They have Similar speed issues. All Configured for Layer 3.
Cisco Switches :: SG300 Switches Can Be Used With Microsoft NLB In Multicast Mode
Dec 18, 2011does the SG300 switches can be used with Microsoft NLB in Multicast mode?I know on traditional Catalyst switches you can statically "map" IP's to mac's and then to multiple ports but this doesn't seem to work correctly on the SG switches - it gives an error about the mac not being not Unicast?
View 2 Replies View RelatedCisco Switches :: VLAN Management Via SNMP On SG300-10 Switches
Aug 7, 2011Any snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies View RelatedCisco Switches :: Multiple VLANS And SG300-28P Switches Setup?
Aug 20, 2012I'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
Cisco Switches :: SG300-52 Multiple Lags Between Switches?
Jan 19, 2012I'm having alot of trouble trying to connect more that one LAG between two SG300-52 switches.Basically i have configured both switches with the same vlans. For 2 of the vlans i would like to connect them together between the two switches using LAG. Switch1 has Vlan 5 (ports 1-12) & Vlan 10 (Ports 25-36) with LAG configured on ports 1-2 and ports 25-26. I have setup the second switch identical to the first. But when i connect the LAG's there is no connectivty. If i disconnect one LAG the other starts working.Can you only have i interconnect LAG between switches?
View 1 Replies View RelatedCisco Switching/Routing :: Telnet On Port 6066 To Configure Router
Apr 23, 2012We have several routers that can only be accessed on telnet port 6066 (vice 23). I have no global exec privilege so I can not provide config.So my question is: how do you configure the router to accept port 6066 for telnet and deny port 23?
View 4 Replies View RelatedCisco Switches :: Enable Telnet In SF 300-24P?
May 19, 2012I have more than 20 SF 300-24P 10/100 Managed Switch switches deployed and running in my office network. All these switches have web configuration utility enabled. We would like to enable telnet too. But for this I know I have to visit site to site, connect the switch manually with a laptop and enable telnet option. I am looking for how can I enable telnet in these switches using web-based switch configuration utility.
View 3 Replies View RelatedCisco Switches :: SF300-48P Option To Telnet It
Jan 14, 2012I have sf300, i didn't found the option to telnet it. default IP of the switch is 192.168.1.254, i can access it by HTTP.
also i'm not able to attach IP phone on voice vlan & computer on vlan 1 ,please share the step by step guide how to access the switch by telnet.
& how to make voice vlan 2 for IP Phones & Vlan 1 for PC.
Routers / Switches :: Still Not Able To Telnet / SSH To Switch?
Mar 14, 2011I can telnet to switch from checkpoint firewall access port and from switch directly. I can ping/traceroute successfully to the switch. Access-lists 14 & 15 are allowing the traffic I want. The router on the other side of the FW has 2 static routes and a default static route set up.
Here is some of the config from my switch:service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryptionhostname xxxxx
enable secret xxxxxx
username xxxxxxxx password xxxxxxxip domain-name xx.xx.netaaa new-model
aaa authentication login default local enable line none[code].....
Not sure of checkpoint firewall config....I have run wireshark when trying to telnet and I get no syn-ack back from remote switch. Just 3 consecutive syn attempts.I have some switches I can connect to and they go right through the 3 way TCP handshake and I cannot find any differences in the configs between the successful connections and the unsuccessful connections.
Cisco Switches :: SFE2000P Failed In Telnet On TACACS?
Mar 17, 2012I'm doing some tesing in SFE2000P linksys switch about the TACACS authentication. I have configured the switch accodringly to point my ACS server with key string. Now, I'm able to login into the switch with TACACS account in HTTP/HTTPS only and but, not with the TELNET access.
Still Switch is authenticating with the local user account only, when in TELNET access method.
Cisco WAN :: SPA3102 - To Configure / Hijack Line RTG Via LAN
Dec 18, 2010I state that I'm very fast Voip router configurations, the problem is as follows: I need to configure a SPA3102 so that I hijack a line RTG via LAN / WAN or on a SPA2102 in the motion that the 2102 can receive and make calls.
View 4 Replies View RelatedHow To Configure To Use Router With Lease Line
Feb 14, 2011How to configure to use Router with Lease Line ?
1.connect a computer to the wan port-router
2.give the ip in the url-------- 192.168.1.1( by default )
3.enter username and passwrd
4. then in the GUI mode
5. go to the wan setting ...router
6.there put the live ip and the gateway and the dns....aircel detail....
7.go the lan setting and put the lan ip series do nt configure dhcp go manually to all the nodes and put the lan ip u have 4 lan ports
8.out of 4 port ...port 1-- connect the dialler...in lan port
9.and in port 2 connect to (switch) a unmanaged switch frm where u can connect to your lan
10.if in the lan setting u hv given the ip 192.168.1.1
11.then put ur dialler ip 192.168.1.2
12. and local lan machine will tk the ip frm 3 onwards
13.nw if u want to authenticate ur dialer in our voip gateway then give the ip of ur router
15. 192.168.0.1 will be the ip of the lan setting in the router
16. and this will act as a gater to ur local machine gateway
Cisco Switches :: SG 200-18 - Change Management-VLAN And Telnet / SSH Access?
Apr 29, 2012We've got a SG200-18 switch that is to be used as a workgroup switch in our environment (SW Version 1.1.1.8). Working with CLI on big and mid-range Cisco-gear over the past two decades I'm having a hard time figuring out the following on the SG200:
o) I want to change the Management-VLAN from the default "1" to the management-VLAN used in our environment. Sure enough I created that vlan in the SG200-config, however when it comes to assigning the management-IP and VLAN for the management interface in the corresponding pulldown under "IPv4 interface -> Management VLAN" the only thing selectable is the default "1". (see screenshots enclosed)So how do I set a management VLAN different from 1?
o) How do I enable telnet/ssh-access to the SG200-18 - I'd be far more comfortable with a CLI-environment?
Cisco Switches :: SRW2024 / How To Upgrade Boot And Software Via Telnet
Mar 26, 2013I HAD similair problem:[URL](Have ver 1.1) Forgot password. Restored to v1.0.0.86 via telnet Been playing around with telnet AND web based updates Read somewhere else (Web-based ONLY works with IE) (Tried Web-based and keep getting "Copy Failed/Undefined Error" and 0 Bytes transfered) Know to upgrade "Boot" first, then "Software Image" THEN reboot
Tried telnet (not through web-based startup) Can get to "lcli" (by Ctrl+Z twice)Retyped Username and Password:
At "console#" tried typing "copy tftp:///srw2024_16_boot-101.rfb boot" didn't work : "Must be valid URL or reserved keyword"
Where am I going wrong?
Cisco Switches :: SG 300-52 Port Gigabit Managed Switch - Cannot Telnet Nor SSH?
Nov 16, 2011We have recently purchased SG 300-52Port Cisco Switch to support our Network but they constantly having some bizarre issues or I assume bugs, i.e. we cannot Telnet nor SSH to the switch now, whereas we were able to SSH before, we have set them up for Remote Log Services to get some syslogs and reports but no report have been generated nor logs,
I have done some testing through Wireshark and there are absolutely no reports / logs.We have some real issues with this switch and it’s hard to believe that this is a Cisco Product,
SG 300-52 Port Gigabit Managed Switch
Firmware Version (Active Image ) : 1.1.1.8
Firmware Version (Non-active ) : 1.1.0.73
Boot Version : 1.0.0.4
Remotely Access 500 Switches Via TELNET And Web Based From Server?
May 15, 2013I want to remotely access Cisco 500 switches via TELNET and WEB BASED from a server. I dont know the ip addresses for Cisco 500 switches which are configured as backbone which the ip address assigned on the network is static ip address. Specifically I want to get their configuations inorder to get their specified assigned vlans on the network. I know the ip addresses for their specified cisco 500 switches' gateways. I know that cisco 500 switches can be accesses through web. Is there other ways to solve the problem apart from going onsite and connect to the cisco 500 switches using network cable since cisco 500 swithes dont have console ports?
View 1 Replies View Related