we just received 5 new SF200-48 Smart Switches for small business. I noticed only way I can configure them is by using the web gui. Is there a way to enable good old CLI?
View 6 RepliesIs there a replacement rackmount kit available for a Smart Switch SF200-48?
View 1 Replies View RelatedI'm currently using LMS 3.2 to monitor my network. We've recently purchsed a few of the Cisco Small Business Switches, the SF 300-24 model to be exact. They're considered 'managed switches' (tho thier CLI is terrible) and I would like to monitor them in CWLMS. My problem is that once I add it to CS, it doesn't resolve to anything, just sits there as a blue box with a question mark. I'm assuming this means that these devices are not (currently) supported by LMS 3.2 - do you know if that will change, or how I can go about managing this device with LMS 3.2?
View 2 Replies View RelatedI have 4 SF300 switches I need to cascade together but the user guides do not seem to cover the physical aspects of cascading the switches.Here is what I was planning.
SW1 (port GB2) --> SW2 (port GB1)
SW2 (port GB2) --> SW3 (port GB1)
SW3 (port GB2) --> SW4 (port GB1)
SW3 (port GB2) --> SW1 (port GB1) - loopback for cascade cable redundancy.
Does this sound about right?after initial use the setup will be changed to place switches 3 and 4 in a factory at which time we will then use the GBIC connectors and fibre to connect SW2 to SW3 and then SW4 back to SW1.
The "Cisco Small Business 300 Series Managed Switches Administration Guide" and the data sheet indicate that this switch can do accounting requests with a Radius server. On the SF300 switch interface/CLI, there is only the authentication port, the accounting port can not be set (and nothing is sent by the switch to the default port). I suppose that the SF300-08 does not handle accounting. Maybe I have to change for another model.
View 4 Replies View Relatedi have a customer that will use this switch model.I was wondering if there is any recommendation from like an AS-BU for the most appropriate software version and what would be ?
View 4 Replies View RelatedThe SMART Designs state that both the ESW500 and 300-series switches should not be used for deployments of over 100 IP phones.But now that both the UC560 can go up to 138 (128 IP phones) and the BE3000 can go up to 300 users is this design restriction still valid or is the Catalyst 2960 and above the only options?
The QPT is still showing both the 300- and ESW500 switches as options for all versions of the UC560, and the 300- and 2960 switches are shown as valid options in the LAN for the BE3000.
Im trying to get my head around my new cisco SG 300 switch. I have used the Linksys SRW range before and configured it using teraterm and method described in the link below:
[URL]
As im fimilar with this method and the commands ideally I'd like to use this on the SG 300 range as well. Failing that, is it possible to use another method which uses the same commands which can be easily copy and pasted for setting up multiple switches with the configuration?
i was able to configure (via SF200 web interface) a port mirroring from port FE17 to FE7.i have supressed this port mirroring.when i try to reconfigure a port mirroring from port FE17 to FE3. The SF200 web interface crash. the SF200 seems to reboot.
i have updated the SF200 firmware from V1.1.2.0 to V1.1.2.9.44 when i was able to configure (via SF200 web interface) a port mirroring from port FE17 to FE7.But after having suppressed this port mirroring again, i was not able to reconfigure a new port mirroring from port FE1 to FE3 (the SF200 hangs).
i have also tried to return to default factory setting but this does not solve the issue.i am working on SF200-24P
I´m a IOS CLI fanatic. Its the first tiem that I have to configure a SB switch. Its very confusing, I want setup a voice vlan id as 200. but I don see that this value change when I try to apply the smartport macro to the interface.Its possible change a smartport macro?
View 1 Replies View RelatedI wonder what is the difference between SF200 and SF200E smart switch. They seem like having same spec.
View 2 Replies View Relatedi was able to configure (via SF200 web interface) a port mapping from port FE17 to FE7.i have supressed this port mapping.
when i try to reconfigure a port mapping from port FE17 to FE3. The SF200 web interface crash. the SF200 seems to reboot.
i have updated the SF200 firmware from V1.1.2.0 to V1.1.2.9.44.when i was able to configure (via SF200 web interface) a port mapping from port FE17 to FE7.But after having suppressed this port mapping again, i was not able to reconfigure a new port mapping from port FE1 to FE3 (the SF200 hangs).
I want to make an offer for a public tender for SF200 Switches (P/Ns SLM224GT and SLM248GT). The end user is already using Cat 6 cables and someone from the committee told that these Switches does not support Cat 6 cables and that the SLM224GT doesn't work correctly with an existing SG200 (SLM2008T) switch.
View 1 Replies View Relatedwhat would be causing my management HTTPS session to a SF200-24 to suddenly timeout? I receive "The session has been timed out. You may log in again" few mins after logging into to switch.Sometime it happens within 45seconds, other times after 3mins, timouts are not consistent. And, i was not idle when it timed-out. My HTTPs idle time-out is set for 10mins.
I had a continuous PING going to managment IP, and it did not drop any pings when session timed-out.Interface stats are also clean. I tried IE, FireFox, Chrome and all are timming out.
I've changed the HTTP default idle-time out from 1 to 10 and my HTTPs stopped timing out. Management Access Authentication is cleary set for HTTPs, and the Idle-timeout for HTTPs was set for 10mins since install. Yet, adjusting the HTTP idle-timeout cleared the issue.
We have been deploying Cisco SF200-24P switches for our systems for over a year now. They connect to a Cisco 881 router. In many cases we are also deploying Cisco AP541s.Over the last few months, on an intermittent basis, the switches will simply freeze, blocking all traffic flow. The power LED also goes dark. It appears the switch has frozen. The only thing that seems to revive the switch is a hard reboot by pulling the power cord. In the last couple of weeks, one site in particular has gone down a handful of times. That client of our is fed up. Our patience is running thin too.
I cannot see any indications in the logs to any event that might give a clue as to the problem. We definitely see this problem with the 1.2.7.76 firmware and the 1.2.9.44 (latest as of typing this). Not sure if with earlier 1.1.2 firmware.Without a fix, we likely will have to change switches and possibly vendors as we need a reliable switch.I see some vague references to a similar problem. And one reference to a SG300 series having what sounds like the same issue.
12 users, 3 servers, 5 smartphones/tables on the WiFi (existing AP), future VPN server (maybe 5 simultaneous inbound VPN connections at the most with at least one client using a Mac), Cisco Gigabit small business switch.Internet access, VPN connectivity, and firewall (reporting, close/open ports for custom applications as needed)I was originally going to select an ASA5505-50 user device for the above client. The device is highly regarded on the Internet, offers a command line interface, priced right for the budget and should perform all duties required by the client.However, the addition of the RV180W to the Cisco product line has me questioning my choice.
1)Does the RV180W offer a command-line interface?
2)Is the RV180W limited in the number of users it can support without having to purchase additional user licenses?
3)How are firmware/software upgrades handled with the RV180W?
4)What will the client be giving up if they choose the RV180W vs. the ASA5505?
I want to know if WAG325N supports cisco's IOS so that i can configure it using command line interface? Is it possible?If not, how would i change ethernet interface speed setting so that it can support 100 mbps of speed. Because when i connect through LAN i'm always getting a full dulplex 10 mbps LAN connection automatically.
View 1 Replies View RelatedI have a sitecom 3G ready wireless router but does not support the local telephone company. i would like to know how to access its modem config from a command line inorder to configure the modem commands with local company settings. Its model no is WL-326v1001
View 1 Replies View Relatedhow to open the Linksys E4200 command line interface? Ive tried using telnet but i get this message:Could not open connection to the host, on port 23.
View 3 Replies View RelatedIs this smart switch possible to do Mac Filtering? how to enable mac filtering on this device?
View 1 Replies View RelatedI'm involved in setting up a new office for a business that's just starting out. I have some computer experience but not a whole lot in networking and security. We just have 3 people that will be working in the office and we need a way to store/backup/share files on the network as well as a way to access them remotely if need be. Our internet service is going to be providing us with a static IP. I was thinking that we could use an NAS with RAID 1 attached to the router, which is in turn connected to the cable modem, but I'm not sure if this is secure. Do we need some type of hardware firewall in between the cable modem and the router to protect us from the outside?
View 2 Replies View RelatedI just took a position and never had to work with networks that much before. Our lan is very slow and trying to figure out why. We have verizon business class 3 t1 lines dedicated 4 M. When I do a speed test we get about 4.05 average and 4.23 down. We have 11 computers on the network connected to a Dell power connect 2716. We have Two network printers and that is it. We are having problems with it being very slow when connecting to a share on the server or using RDP.
View 4 Replies View RelatedI work for a small business of five computers. We have a wireless network for internet traffic, and a wired network for file sharing. The wireless network works great for using the internet, but we are having trouble with the wired network.The issue is being able to communicate with all of the computers on the wired network. The ability to speak with all of the computers on the network is hit or miss. Generally, computer A can speak with computer B, C, and D, but D can only speak with A.
View 4 Replies View RelatedHe currently has 1 server, and 11 workstations, he also has a network switch that we will be replacing.We have picked out a Dell server, running Windows Server 2008 R2 that will be used as the main file server, as well as the domain controller. Where I seem to be confused is on setting up the networking component, particularly how the machines will get IP addresses. As mentioned, I will be purchasing a new Ethernet switch, in order to get the fastest LAN speed possible; I have selected the Dell PowerConnect 2816, which is a 10/100/1000Mbs switch. My question is, will I be letting the switch handle the IP's/DHCP or would I be better off, setting up the server for DHCP? If so, do I also setup the server as the DNS server? From what I am reading online using the server as the DHCP/DNS server gives us more management capabilities and is more "secure". As a test, I loaded Windows Server 2008 R2 on a home machine and played around with this. I got a bit lost on the DHCP and DNS setup and it appears that one needs a Static IP from your ISP in order to setup your serve as the DHCP/DNS server for the domain. Is this correct? I haven't been to his office yet to check out all the existing equipment, is it safe to assume that his ISP provides a router or whatever is needed to feed the switch?
View 3 Replies View RelatedI have a small, simple small business network. There are 2 switches - an 8-port switch connected to my main Windows server (which is the DHCP provider for the network), and a 24-port switch which is plugged into the 8-port switch.
I replaced these switches (Dell unmanaged switches) with the Cisco 200 series smart switches (the 8-port and 26-port models). When I plug the 26-port switch into the 8-port switch, it is unable to get its DHCP address from the Windows server. Also, any device plugged into the 26-port switch cannot communicate with any other device, and all of the ethernet port lights flash at the same time at the same frequency - quite a light show!
If I plug the Windows server DIRECTLY into the 26-port switch it receives a DHCP address.
I have tried a 2nd Cisco 26-port swtich and it does the same thing, so I assume it is not a hardware issue.
I am looking to start a proposal for the smallish business I work for. We have about 65 devices on the network with ~ 12 being VOIP phones. Currently our network consists of 2 cisco 2950's and a bunch of daisy chained consumer 5 port switches. I would like to get a couple of 48 port 2960S or 3XXX series catalysis' and run drops to all the devices. It's an older brick building with beamed 15 foot ceilings. It has a couple of semi-enclosed office spaces, with one large space for all the developers and designers. The plan I have involves running a cable tray down the length of the office and run drops off of the main run. I would like to be as cheap as possible with the cable tray, but it seems like all the trays I have seen are about ~50-100 dollars per 10' (not including mounting hardware). Seems extremely expensive for basically wire baskets.
View 3 Replies View RelatedI need an example of a insecure network configuration that is may occur in small-business.For example insecure devices that can be used or how they are connected with each other. Also router/nas/pc configurations. With wireless network it is easy, but i am not familiar with wired networks. Specially I need weak points of a router configurations and weakly designed connections between different devices.I need to design a insecure small-business network configuration for my school project. For example 2 workstations, 1 laptop, NAS, network printer, VoIP telephone etc. After that I need to analyse these weak points.
View 3 Replies View RelatedI have a small business with 1 "server PC", 7 PC's & 2 Mac's (and a WiFi TV)Oh and a copier.the server reaches the internet from the wall socket through the copier through a router through a WAP finally to Server. All wired PCs can see the server and interact with it and the copier. All wireless devices (through WAP) cannot access the server computer or the copier. There is no inexpensive way to get a wire to the devices with out causing a tripping hazard or lots of unsightly strung wires. Why are the wireless connections not seeing the server and can I fix that by reconfiguring the setup of my existing devices?
View 6 Replies View RelatedWe recently deployed SG300-28 to replace an old 3Com switch.The setup: RVS400 router and all workstations and server are plugged into the SG300 switch.The problem: Windows 7 workstations are unable to obtain IP addresses from the server which is also plugged into the switch.If however, we plug in the worstations into the 4 port switch on the back of the RVS4000 (the router), they get IPs from the server no problem. This worked just fine with the old 3Com switch.
View 15 Replies View RelatedI have recently purchased a Cisco 887w router for my small business to replace our Netgear DGN-3500. We have made the change to allow greater access to our internal IT infrastructure from remote locations. For the most part I have been able to work through the configuration but I have reached a point now where I can go no further. The WLAN, LAN and WAN all seem to be working well together as a basic setup but I cannot get any port forwarding/NAT to work.
So far I have attempted to configure two NATd services, both with the same result. I am trying to direct port 80 through to our web server, and port 444 to our VPN server. Both seem to undergo translation ok (if i am reading ip nat trans output correctly) but then the packets disappear. The VPN client annouces that the connection timed out, and the browser goes nowhere. Also, if i use an online port check it tells me that 80 and 444 are closed, with no packets returned.
I have spent a few days with no progress. The output of the log (attached txt file) might be meaningfull to somone with a stronger background with Cisco routers... I have also included the config and some other output that might be useful.
I'm trying to configure the newly install Cisco Small Business router SRP527W. This router is provide by one of Malaysia ISP
Problem I found is that, when a user (me) login to the router via web access, than I request my colleague (B), to test the feature I set to the router and try to login to the router via web access at his laptop.
Suprise, suprise, user B redirect to the basic setup page with Admin privilege without enter username and password. By upgrade latest firmware still unable to solve it.
I'm searching for a managed switch that allows me to not only mirror a port/ports, but also to still use the destination port for the mirrors as a link to the internet/the rest of the network. Aside from this, I still need the VLAN functionality of good switches, and ideally PoE provided, too.
I have seen the majority of the features of this in the NETGEAR GS108E (http:url...), but this doesn't provide PoE to the ports and also requires Windows to log into.Is this a feature of many switches? I can think of many snooping applications where it would be incredibly useful.
is file storage of a small business referring to a file server?
View 1 Replies View Related