I have a sitecom 3G ready wireless router but does not support the local telephone company. i would like to know how to access its modem config from a command line inorder to configure the modem commands with local company settings. Its model no is WL-326v1001
View 1 Replies
how to open the Linksys E4200 command line interface? Ive tried using telnet but i get this message:Could not open connection to the host, on port 23.
View 3 Replies View RelatedI want to know if WAG325N supports cisco's IOS so that i can configure it using command line interface? Is it possible?If not, how would i change ethernet interface speed setting so that it can support 100 mbps of speed. Because when i connect through LAN i'm always getting a full dulplex 10 mbps LAN connection automatically.
View 1 Replies View Related12 users, 3 servers, 5 smartphones/tables on the WiFi (existing AP), future VPN server (maybe 5 simultaneous inbound VPN connections at the most with at least one client using a Mac), Cisco Gigabit small business switch.Internet access, VPN connectivity, and firewall (reporting, close/open ports for custom applications as needed)I was originally going to select an ASA5505-50 user device for the above client. The device is highly regarded on the Internet, offers a command line interface, priced right for the budget and should perform all duties required by the client.However, the addition of the RV180W to the Cisco product line has me questioning my choice.
1)Does the RV180W offer a command-line interface?
2)Is the RV180W limited in the number of users it can support without having to purchase additional user licenses?
3)How are firmware/software upgrades handled with the RV180W?
4)What will the client be giving up if they choose the RV180W vs. the ASA5505?
i would like to configure the wireless access on the cisco 877 router either on command line or gui -also, does the wireless authentication and SSID has to be local or can i put the cisco 877 on h-reap mode and connect back to my controllers in head office and use the same SSID as in my head office ?
View 8 Replies View Relatedwe just received 5 new SF200-48 Smart Switches for small business. I noticed only way I can configure them is by using the web gui. Is there a way to enable good old CLI?
View 6 Replies View RelatedOn my old 2511 access server, I could issue "clear line x" to close a session on an existing line.this doesn't seem to work on my new 2600XM with NM-16A access server (12.3(20)IOS), any command in newer IOS?
View 4 Replies View Relatedwe just bought a 2921 with the following modules: 4 port clear channel T1/E1 HWICSM-ES3G-24-P: EtherSwitch.I read some CISCO documents, and not be able to find what I need. I would prefer all instructions from you are for CLI interface.This is my first time to deal directly with T1, WIC and 2921 etc. The following is what I get from ATT, IP masked IP Address Block IP Address: 20.20.20.136/29 WAN Link Details: WAN Link IP Address:13.13.13.92 AR Serial INT IP Address:13.13.13.93 CR Serial INT IP Address:13.13.13.94 WAN Link Subnet Mask:255.255.255.252
A: how do I configure T1, what does "AR, CR" stands for, and do I need to use both IP addresses? What is the WAN Link IP for?
B: We have two T1 lines, so I should plug them both to the WIC, say port 0 and port 1, how to configure them?
C: how do I access the firewall from the command line?
D: I followed T1/E1 HWIC installation guide, and as soon as I add channel-group to the controller t1, the serial interface went down?
I am having some difficulties on finding information on how to setup two Cisco 1252 autonomous access points, via the command line. I am not having any luck finding steps on how to go about doing this and was curious if any one would be willing to give some insight. I am working on taking two of them setting one up as the root bridge and the other as non-root.
View 3 Replies View RelatedI had insatalled the ACS 5.2 on Vmware . As per my requirement i need to configure a user to restricted privilege so that he should be able to execute only the below commands on the switch .
-Show ver
-Show interfaces
-Show ip Interface Brief
-Configure terminal
-Interface <interface name >
-Shutdown
-No shutdown
The users should not be authorized to execute any other commands than above listed one .After the configuration i was not able to restrict the config mode commands . Once the user is authoized for Configure terminal access he will have full access on the device. How to configure the command set only to allow interface access and he should be able to apply Shutdown and No shutdown command .
I configured a 1841 router that connects to a DSL modem. This DSL connection is our Internet connection for vendor and IT testing. I have connectivity to the Internet using nat and have configured the router to act as a DHCP server. It seems to be working fine. I just want to configure some best practices for securing the device from the outside access. Is there some standard best practices I should be configuring?
View 2 Replies View RelatedI recently changed the entire configuration on two 6509 switches, and the fibre modules on slot 7 and 8 have gone down on BOTH switches. It would be easy to say that its a hardware fault but I cannot understand how module 7 and 8 can go down on both switches. Initially I thought it maybe due to IOS bug 22-33.SXI2a.bin" so I upgraded it to s72033-advipservicesk9_wan-mz.122-18.SXF12a.bin but it still down.These are the actions I have carrried out to try resolve the issue:
- Reverted back to orginal configs but no luck
- Tried to use "power enable" command but the status light on both modules seems to turn red and then go off again.
- I have also tried to put one of the fibre modules into a different slot but no joy
- Upgraded the IOS from 22-33.SXI2a. to 122-18.SXF12a
I am sure that hardware fault cannot occur on BOTH modules 7 & 8 on BOTH switches after config change.The error in the log shows that modules "failed to bring online because of registration timer event". I understand this means that it is unable to download the image within the allocated time. [code]
My grandma has a PC with Windows XP, she uses it only for Skype calls. can go in to her PC using command line from my PC? What commands should I use and what modifications to do on my grandma's PC? Should I ask permission from grandma's ISP (which is the same as mine)?
View 3 Replies View RelatedI have been working with the 871 router and configuring it for work at home users. Now we are purchasing and using the 881's instead. I noticed that after write erasing the router, I need to run the command in the global config "license boot module c880-data level advipservices" just have eigrp.However when I type show license, I get the following:
Index 1 Feature: advipservices
Period left: 8 weeks 3 days
Period Used: 2 hours 55 minutes
License Type: EvalRightToUse
[URL]
There is more but I left it out. However it shows that the advipservices license has only 8 weeks and 3 days left.What is this? I thought that when I buy a brand new router, I should get everything, including IOS licenses. So I would like to know is this a new licensing scheme and how does it get register and how do I get it so that the advipservices license is permanent?
I am trying to assign a static ip and default gateway to my LAP through the CLI, but after I reboot it, I lose the config and it reverts back to dhcp. Is there any command to save the config to the AP through the CLI? I've tried all I can think of (i.e. wr mem, copy run start, etc...) and have looked throught the available commands but cannot figure out a way to do it..
View 6 Replies View Relatedwhat happens internally when no shut command is given on the interface of router.The router interface goes up. How? What happen internally on the interface of the router?
View 8 Replies View RelatedOn a number of 6500 chassis it appears that linecard 3 did exist at somepoint, but was removed.Problem is that when issuing the 'show int desc' or 'show ip int brie' the ports for the still appear, and indeed same with 'show run' and 'show conf'.
View 1 Replies View RelatedI want to telnet a router (say) 1.1.1.1 with usename "user" and password "pass" in command line. i tried using....telnet 1.1.1.1 -l user ..........but not working
View 3 Replies View RelatedMy 3550 is always 2 characters short on the command line. So my global configuration mode will look like this:Switch3550(config Say I wanted to enabled ftp, it would look like:Switch3550(config)# ftp enab.
View 2 Replies View RelatedIm trying to get my head around my new cisco SG 300 switch. I have used the Linksys SRW range before and configured it using teraterm and method described in the link below:
[URL]
As im fimilar with this method and the commands ideally I'd like to use this on the SG 300 range as well. Failing that, is it possible to use another method which uses the same commands which can be easily copy and pasted for setting up multiple switches with the configuration?
I'm an ASDM 6.4 command line novice & I'm looking for the command to delete an unused vpn key, e.g. 'key1'.Or if there's a GUI method?
View 2 Replies View Relatedcommand to get running config of Cisco VPN 3000 concentrator.
View 3 Replies View RelatedWe have lots of new lap1041 need be set static IP Adress, hostname, Controller Adress via command line, but when use command (capwap ap hostname) to set hostname , always give us command disabled, we used command:clear capwap private-config, but it does not work, why?
View 4 Replies View Relatedmy environment:
IE-3000-8TC industry-switch
ios: ies-ipservicesk9-mz.150-2.SE2
if i do
vlan 12
name NextVLAN
state active
in putty, everything is ok. but if i set this lines in a config-file and use them by config net or copy tftp: running-config, then this commands are completely ignored.how to setup VLAN so that this are funktional. i dont need a "interface vlan xx"! in addition manually configured vlan are shown in show vlan command but there are no entries inside a sh running-config output even i user show running-config all.
I am looking to replace the active supervisor (S720-10G) on our 6509E running in SSO mode. The new module already has the same IOs version as the standby supervisor.Once I have swapped the module how do I know that the config has sync'd correctly other than checking the logs? Is it a case of looking at the "Redundancy Mode (Operational)" state and ensuring is says SSO?Also, is there a command that will force a config-sync if it is running in a mode other than SSO?
View 1 Replies View RelatedI'm probably overlooking something very simple but is there a command to show the uptime of a router interface in days,hours,minutes?
View 3 Replies View RelatedI am replacing a 7204 router with a 4948 and am having trouble trying to replicate the config for the qnq Layer3 interface.A bit of background - I am a service provider where I have an interconnect with the carrier, who pass off WAN links to me as a standard VLAN Ids. Some of these VLANs however I can do QnQ.
This works fine - but I can get the second-dot1q 50 command working properly
I posted before about my problem in forwarding certain ports in a LAN-to-WAN cascaded router setup, and I finally gave up looking for a solution, and went for a LAN-to-LAN. On the internet there is many articles to be found on how to accomplish the setup, but none of them is complete, and as such, I think I really screwed up someplace. My setup: ISP modem/router (192.168.1.1 / 255.255.255.0) DHCP enabled, and DHCP address range 3-100 NAT configured Static IP address for a Synology NAS connected to the E4200 SSID id_1
Then the E4200 Internet connection type: I set to Static IP IP 192.168.1.2 Subnet mask 255.255.255.0 Default gateway: 0.0.0.0 (to disable the WAN)
Then, the network setup: Router IP: 192.168.1.2 gave me the error that WAN and LAN IPs were identical. I played around quite some time but always got an “illegal value” error. Then finally I put the IP to 192.168.0.1 (IP I had in LAN-to-WAN) and this was accepted. And subnet mask: 255.255.255.0 The SSID I left unchanged from what it was, id_2 (also gives me the advantage that I know to which router I am connected)
I rebooted the E4200, and I was connected. But … I am unable to connect to the E4200 configuration page, and even Cisco Connect cannot establish the connection.
WRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. After all that I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port.
View 4 Replies View RelatedI keep getting this error every few days and I have to restart my router in order to gain access back to the web utility. I reflashed the fw a second time with no success. I have read about this trip 30 reset but have had no luck finding a post which describes how to go about that method.
View 5 Replies View RelatedWRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port. Also the support site has been down for over 13 hours for routine maintenance service.
View 2 Replies View Relatedhow i can change WRT160Nv2 settings if i cannot find it with default 192.168.1.1;i'm using it as secondary router connected to FIOS actiontec primary, which has the 192.168.1.1; factory default reset linksys to that same IP, can't get it.cannot get internet without actiontec as its coax connected, and linksys doesn't have coax port.can'ty open configure page without internet connection, i believe.tried to use a neighbor's wireless but that's using 192.168.1.1 as well, can't log in to that.this started with firmware upgrade of linksys which left it invisible; didn't complete the upgrade, i don't think. but i've reset it and still nothing.
View 9 Replies View RelatedRegion : UnitedKingdom
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :
ISP : Virgin Media
Bought recently and I'm very pleased with Setup and Performance.
However, even though I have tried repeatedly with different user details and passwords I cant access the router Config without resetting to defaults using the pin in the back and admin admin.
I am using W7 and get to a log in screen via Control Panel / ... Network Sharing Centre / Network Map and see Router. Click on this and up comes a User Name and Pasword form but it never works with what I entered for the router.
