Linksys Wireless Router :: Cannot Access E4200 Config In LAN-to-LAN
Jan 31, 2012
I posted before about my problem in forwarding certain ports in a LAN-to-WAN cascaded router setup, and I finally gave up looking for a solution, and went for a LAN-to-LAN. On the internet there is many articles to be found on how to accomplish the setup, but none of them is complete, and as such, I think I really screwed up someplace. My setup: ISP modem/router (192.168.1.1 / 255.255.255.0) DHCP enabled, and DHCP address range 3-100 NAT configured Static IP address for a Synology NAS connected to the E4200 SSID id_1
Then the E4200 Internet connection type: I set to Static IP IP 192.168.1.2 Subnet mask 255.255.255.0 Default gateway: 0.0.0.0 (to disable the WAN)
Then, the network setup: Router IP: 192.168.1.2 gave me the error that WAN and LAN IPs were identical. I played around quite some time but always got an “illegal value” error. Then finally I put the IP to 192.168.0.1 (IP I had in LAN-to-WAN) and this was accepted. And subnet mask: 255.255.255.0 The SSID I left unchanged from what it was, id_2 (also gives me the advantage that I know to which router I am connected)
I rebooted the E4200, and I was connected. But … I am unable to connect to the E4200 configuration page, and even Cisco Connect cannot establish the connection.
View 9 Replies
ADVERTISEMENT
Aug 27, 2011
I was changing some settings on the router, disabled the WMM QoS, and I can no longer see either the 2.4 or 5GHz networks. I power cycled, tried resetting to defaults but the wireless seems to be dead. I can manage it wired, but that does me no good.
View 2 Replies
View Related
Apr 18, 2013
WRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. After all that I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port.
View 4 Replies
View Related
Jul 15, 2011
WRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port. Also the support site has been down for over 13 hours for routine maintenance service.
View 2 Replies
View Related
Jan 7, 2011
how i can change WRT160Nv2 settings if i cannot find it with default 192.168.1.1;i'm using it as secondary router connected to FIOS actiontec primary, which has the 192.168.1.1; factory default reset linksys to that same IP, can't get it.cannot get internet without actiontec as its coax connected, and linksys doesn't have coax port.can'ty open configure page without internet connection, i believe.tried to use a neighbor's wireless but that's using 192.168.1.1 as well, can't log in to that.this started with firmware upgrade of linksys which left it invisible; didn't complete the upgrade, i don't think. but i've reset it and still nothing.
View 9 Replies
View Related
Nov 15, 2012
I've been trying to get FTP Running up on my router for some time now.
I know my current WAN address and have setup a specified folder on my E4200 for the FTP partition. A username for myself has been created with login info and I have forwarded the port I have specified on my router's FTP configuration page.
I try to log into the server, but whenever I try to log into it, I keep getting a "incorrect login information" message back at me.
If I cancel out of that then I get an error message saying it can't find the specified folder and to check the address of the server.
I know the login information information is correct and I've tried changing the password to others of varying lengths.
I've also tried changing the port I'm running the FTP off of incase my ISP has blocked that port, nothing works.
View 9 Replies
View Related
Nov 10, 2012
i have installed lutron lighting in my home and need to configure e4200 so i can access it from outside home with iphone application. Lutron manual says to go to VPN iphone setting and add PPTP connection, server, account and password. I need to do same on e4200 but not sure where to go create pptp connection, accounts and passwords?
View 4 Replies
View Related
Jun 18, 2012
I have my main router, a E4200v2 which I use as a router and it provides wireless signal throughout my house, however reception is not as strong on the upper floor and there is a slight dead spot, so I purchased an E4200 for the uppermost floor.I set the E4200 to bridge mode so it will act solely as an AP.However connecting the two routers LAN to LAN and the AP does not access the internet.Setting a static IP for the router, instead of acquiring one via DHCP causes me to not be able to access the admin page on the AP.
Connecting WAN on the E4200 to the LAN on the v2 does not work either.My goal here is to have my main router on 192.168.1.1 and the AP on 192.168.1.2 where I can access the admin settings for both routers in case I need to make changes.
View 9 Replies
View Related
Jun 15, 2012
Just got a new hard drive installed on my laptop, and now for some reason I can not access my router. I am connected to the internet, and everything is fine there, but when I type the 192.168.1.1 and enter admin as the password, it shows that I am unauthorized.
I have a Linksys E4200 router
View 2 Replies
View Related
May 24, 2012
I recently put in a surveillance system with remote access. I have an application on my android phone and it can be viewed by any browser. While I am connected to my network these functions work fine, on my phone and any desktop/laptop. The problem happens when I try to view remotely, off my network. I had this setup on my Netgear router before I got my new fancy schmancy Cicso router becaue the netgear wasn't cutting the cheese in keeping my wireless connectionstory.So here is what I got. I need 3 ports forwarded for this work, and how I got it work on my Netgear. I have these 3 ports forwarded as single ports. I have them forwarded in a range and I have port triggering turned on. No matter what or which combination of these few things I try, I can't access the DVR remotely, again unless I'm local to MY network.Some additional notes - the DVR has a static address and that address has been reserved in the DHCP settings of the router.
View 5 Replies
View Related
Nov 13, 2011
I have a problem te access e4200 with web access on a iMac with Lion 10.7. I try to connect with standard Safari.With 192.168.1.1. it won't open, if I look voor IP address it should be 192.168.0.1. now the login screen opens but now I can't login with clean name en password "admin" it gives an error.I also can't install Ciso Connect from CD, it gives a error not right version!.Is there anyone that use iMac with E4200 and Sonos zone player?
View 3 Replies
View Related
Aug 11, 2011
how to setup the E4200 so that I can access the media server when I am in office? I was browsing on the Cisco website and unable to find it.
View 8 Replies
View Related
Aug 21, 2011
If you have MAC filter enabled with the E4200 Firmware Version: 1.0.01 you cannot connect to guest.
View 2 Replies
View Related
Nov 9, 2011
i enable guest access, when connecting though any device it doesn't ask for password but allows access straight away. I've tried changing the password, but no luck.
View 3 Replies
View Related
Sep 26, 2011
I have a Linksys E4200 router with firmware version 1.0.02. I am using a Macbook Pro. I can connect to a VPN server with the default VPN client software, but it kills my internet connection and disables connecting to SMB
View 5 Replies
View Related
Oct 11, 2011
I've got an E4200 at my house. I'd like to know if it's possible for my to establish a VPN connection from a remote location to login to my E4200 to get access to my computers behind the firewall.
View 1 Replies
View Related
Aug 6, 2011
I cannot connect to my company’s VPN after installing the current firmware (FW_E4200_1.0.02.013_US_20110524) on my E4200 router. Version 1.0.01 was on the router when I received it, and it worked without issues. As soon as I upgraded version 02, I could not initialize a VPN connection. When I try to start a VPN session, I get a "page not found" error when attempting to initiate SSL VPN service using a Microsoft Forefront Unified Access Gateway. VPN pass through is enabled for all protocols in the e4200’s setup. As soon as I revert to firmware 01, everything works fine again.
I did a fresh download and re-flashed the 02 firmware just to make sure that it wasn’t an issue with a bad download or a faulty flash. The problem is consistent and repeatable. I have upgraded and downgraded twice, and the results are exactly the same. My VPN connection works with firmware 01, and it fails with version 02. There is a something different in the 02 firmware that is blocking VPN access.
View 9 Replies
View Related
Sep 19, 2012
I recently bought a e4200 v2 and installed connect cloud. I have attached a USB drive to the router. I can connect to it by mapping a network drive on my windows 7 laptop. I can also access it as a media server through my iPad on the local wifi network. This way I can play the music on the USB drive through the iPad. The next thing I would like to accomplish is to be able to listen to the music on the USB drive through the internet (so remotely).
View 2 Replies
View Related
Jan 22, 2012
I have broadband internet coming into 1 room of my home. The internet goes through a router I have set up, its a Linksys WRT54G2 (router #1), Firmware version 1.0.04. Everything on this works fine, I'm able to get my TV and laptop in a different room to access the router wirelessly without any inconvenience.In another room I have a regular desktop computer which I would like to get internet on. As well as other devices, so I purchased another router, this time a Linksys E4200 (router #2) in hopes of turning it into an access point.Now I've set up LAN's in the past, using the actual cable plugged into the second router, problem is in this scenario I can't run a cable over to router #2. Both computers use Windows 7. Both router's drivers and firmware have been updated on the Linksys page, all my Windows drivers are updated, etc. I checked other forums for similar questions and although there are some, they date back to 2009 as well as Google which has some websites dating back to 2006! While useful, I wasn't able to find something that details how to solve my problem with my specific setup. I've already gone into router #2 and changed the router's IP to 192.168.1.2 and also turned DHCP off, problem is, once I take that router off into the other room, it doesnt connect to primary network or allow devices to even "see" router #2.
View 2 Replies
View Related
Apr 18, 2012
I just bought an E4200 and it was working perfectly, very easy to install, all that it promises. Then I had an energy peak. For some reason, don't ask me why, I did RESET the router not thru the web nor thru Cisco Connect, but pushing the reset button at the back. I can't access the router anymore ! It keeps asking for a password that is never accepted. I have uninstalled cisco connect and tried again. Nothing. The router is not found. Keeps asking for a password. I tried everything: blan+admin, admin+admin, the password I used to have (provided at the cisco connect uninstall).It seems that the RESET never worked. The router is working thru cables, meaning when I can connect to the internet wired. But the router is never found wireless.How could I update the firmware if the router is not recognized (or if I don't have a username+password) ?
View 9 Replies
View Related
May 24, 2012
I recently bought the E4200 v2. When I first installed, I ran the firmware update and then performed a hard reset (push reset button for 20 secs). I then began to enter all the PPPoE information and network settings into the new router (verified these settings with the existing WRT54GL router I'm current using and they all matched). I then disconnected the old router, and powered up the E4200. I was able to access the new router (192.168.0.1), I could see all previously shared files/computers with the new router, but I could not access most websites - usually I got a timeout error, or they eventually loaded in 10x the usual speed. This was typical of both laptops - one wired, and one wireless. My wireless handheld device could connect to the wireless network, and ran a speeedtest.net test, and upload/download speeds were normal - but I could not access the internet from the device. When I switched back to the old router, everything worked perfectly again. I have tried some suggestions on changing MTU values, but that did not seem to make any difference.
As a work-around, I have ended up keeping the WRT54GL as the main router and using the E4200 in bridged mode for wireless only (not what I ideally would like)..
View 4 Replies
View Related
Nov 17, 2011
The Guest Access is a very nice feature for allowing us to provide Internet access in our rental unit.
However, it would be nice to provide the Guests access to the USB printer.
Is there a way to provide access to the USB printer for those who are logged into the "Guest Network"?
View 2 Replies
View Related
Sep 18, 2011
Upon attaching my external storage I was able to create a share, copy files and access it successfully from everywhere. Now when I attempt to add an additional share, the router lets me create it but when I try to move access groups over from the available groups, the >> buttons are greyed out. The one working share has the admin and Everyone groups with access. Any additional share I create has the admin group in it by default, but I can't add any more groups. I am logged into the router as admin and logged into the pc as a local admin. I am also unable to change the rights from my pc on a share (access denied). I AM, however, able to map a drive to a new share successfully, but when I copy files over, a few minutes later the filenames are there but they show up as 0 byte files.
View 7 Replies
View Related
May 3, 2012
I've been on DSL with British Telcom Infnity (FTTC) since March and had no problems with the service. My router, however, an Apple Time Capsule, was not so reliable and needed a reboot every few days,So I just purchased the E4200 V2The Setup completes OK and PPPoE logs into my ISP fine. But then I hit the problem.Most of the websites I use simply won't load . In Safari on my OS X Lion, Macbook, I get an error like this "Request Timeout. The server timed out while waiting for the browser's request. Reference #2.525fdd58.1336048435.0" In IE on my Windows XP laptop, the error is "Internet Explorer cannot display the webpage"But some websites still load fine. So [url]..., loads instantly. Most other sites I try, including [url]... - won't load at all. (Plusnet is my ISP)If I connect to my work VPN, I can browse as normal
View 9 Replies
View Related
Mar 26, 2012
I have the guest Access enabled on my E4200 but I can't get any of the apple devices or dell laptops to show the LOGIN screen in the web browser.
View 1 Replies
View Related
Nov 13, 2011
Purchased E4200 this week and did simple setup via CD setup (Cisco connect). Set up main name and password. Cisco Connect assigned "-guest" to end of main name for the guest account. Gave guest account its own password. Both main and guest accounts were broadcasting OK -- but guest account was not secure and could be accessed without password. (All software and firmware upgrades were done during initial setup).Reset the E4200 and restarted things from the CD setup. Created main account, main account password, and guest password again. In advanced settings, left basic wireless settings at initial settings, changed wireless secutiy to WPA2 Personal. Still having the guest account being broadcast in unlocked status. (Have turned off guest access for now until I can get password protection for it).
View 1 Replies
View Related
Nov 2, 2011
Recently installed an E4200 router to an MacPro following the setup as directed by Cisco Connection (connect Ethernet to router and then computer to router.) The wireless and the hard-wire connectivity works fine with accessing the internet. However, we have lost the ability to connect to other computers on our LAN via the Shared folder connection. This is usually accessed via the Sidebar (see image)
However with the E4200 in the mix, all we see is the router per its "given name" (what it was named on installation). I have tried to follow the advice mentioned in other threads, such as "Can't access network shares with E3000" and nothing worked-- and those threads seemed to apply to Windows and PCs anyway.
View 6 Replies
View Related
Feb 7, 2012
With the E4200, is it possible to setup the main SSID with a pass pharse but have the guest SSID without a passpharse or password (ie access without security). If so, How?
View 1 Replies
View Related
Jan 2, 2012
I got my NTFS formatted drive to work with the E4200 router via its USB port.I do not see any 'Access' option to configure different access types based on users. I do have users configured in the Administration tab; these are what came per-configured on the router.
View 4 Replies
View Related
Dec 30, 2011
After I installed E4200 v2, I got a problem with some web pages like facebook (either do not open or not dispaleyd properly) and msn and also yahoo messenger I can not access, I have a PPPoE internet.I tried to do factory reset and updated to 2.0.26 firware but with no luck the problems persisted... I connected my old one E1000 and it had none of the probelmes I mentioned..
View 9 Replies
View Related
Aug 26, 2012
My serial number on the E4200 starts with 01 - does that indicate it is a version 1? If not, how do I determine which version I have? Are there any software updates available? How do I disable my guest access?
View 1 Replies
View Related
Feb 28, 2013
I cannot get my iPhone 5 to access my wireless network (Linksys E4200) since I reset the router. It asks for the password but doesn't accept it. I'm a newbie so be gentle with me! MSZ
View 2 Replies
View Related
Apr 28, 2012
Have just changed my E4200 to EA4500 but can my computer has not IE access. Both router has same settings and the mac adr are both in the modem at the local cabel firm.
View 4 Replies
View Related
