Linksys Wireless Router :: E4200 - Guest Access Through Web Browser?
Mar 26, 2012I have the guest Access enabled on my E4200 but I can't get any of the apple devices or dell laptops to show the LOGIN screen in the web browser.
View 1 Replies
ADVERTISEMENT
Linksys Wireless Router :: E4200 Wifi Guest Access Never Pops Up Browser
Dec 5, 2011I have the wireless guest access set up in my E4200 flash to the latest firmware. When I connect to the wireless guest network it comes up under the 192.168.33.xx IP address. I can connect fine but it never pops up the browser so that you can type in the guest password. I'm running Windows 7 but I've also noticed the exact same problem under XP.The only thing I can guess is the problem is that I have this acting like an access point and all DHCP requests go to my router. I've basically turned off DHCP on this and plugged the network connection into the switch on the back.
View 3 Replies View RelatedLinksys Wireless Router :: E4200 - No Guest Access With Mac Filter?
Aug 21, 2011If you have MAC filter enabled with the E4200 Firmware Version: 1.0.01 you cannot connect to guest.
View 2 Replies View RelatedLinksys Wireless Router :: E4200 Guest Access Won't Ask For Password?
Nov 9, 2011i enable guest access, when connecting though any device it doesn't ask for password but allows access straight away. I've tried changing the password, but no luck.
View 3 Replies View RelatedLinksys Wireless Router :: E4200 Guest Access To Printer?
Nov 17, 2011The Guest Access is a very nice feature for allowing us to provide Internet access in our rental unit.
However, it would be nice to provide the Guests access to the USB printer.
Is there a way to provide access to the USB printer for those who are logged into the "Guest Network"?
Linksys Wireless Router :: E4200 - Guest Access Not Secure
Nov 13, 2011Purchased E4200 this week and did simple setup via CD setup (Cisco connect). Set up main name and password. Cisco Connect assigned "-guest" to end of main name for the guest account. Gave guest account its own password. Both main and guest accounts were broadcasting OK -- but guest account was not secure and could be accessed without password. (All software and firmware upgrades were done during initial setup).Reset the E4200 and restarted things from the CD setup. Created main account, main account password, and guest password again. In advanced settings, left basic wireless settings at initial settings, changed wireless secutiy to WPA2 Personal. Still having the guest account being broadcast in unlocked status. (Have turned off guest access for now until I can get password protection for it).
View 1 Replies View RelatedLinksys Wireless Router :: E4200 Guest Access Without Password?
Feb 7, 2012With the E4200, is it possible to setup the main SSID with a pass pharse but have the guest SSID without a passpharse or password (ie access without security). If so, How?
View 1 Replies View RelatedLinksys Wireless Router :: E4200 Version And Guest Access?
Aug 26, 2012My serial number on the E4200 starts with 01 - does that indicate it is a version 1? If not, how do I determine which version I have? Are there any software updates available? How do I disable my guest access?
View 1 Replies View RelatedLinksys Wireless Router :: Guest Access Is Not Remembered When E4200 Powercycle
Aug 12, 2011I have changed from dlink to linksys because of good reviews in transfer speed. Nothing to complained about that yet, Wireless guest zone has more to wishes... Disable password req is one, why call it guest and show it as an unsecured network (I know it separated from my local network and doesn't have encryption)? This password req is a bum when visitors with smartphones and ipods came and visit! More irritable is that somehow connection settings for guest in devices are lost when e4200 powercycle and every visitor must reconfig their devices again
View 7 Replies View RelatedLinksys Wireless Router :: Hide Passwords In Cisco Connect And In Browser UI For E4200?
Mar 13, 2012I just purchased a E4200 and I have some questions;
1. I have the hardware version 1, and I noticed the hardware version 2 has a newer version of Cisco Connect. Can I use the newer version of Cisco Connect on my E4200 V1?
2. Is there a way to hide passwords in Cisco Connect and in the browser UI for the router?
3. Is there a way to have a separate admin password and wireless password?
I also have a issue, I want the browser web UI to display in english, but it insists on changing it back to my native language from time to time.
Linksys Wireless Router :: E4200 Guest Network Via LAN?
Feb 21, 2013I have the wireless guest network up and running just fine. But, I need to also connect to the router's quest network via one of the ethernet ports. Can I just give the LAN-conencted PC a 192.168.3.x static IP to access the guest network? I am assuming there is no VLAN functionality...
And even better, can I set up a DHCP relationship to that port? So that any device plugged into the port will get a IP on that subnet?
Linksys Wireless Router :: E4200 Guest Network Not Working
Jun 24, 2011I cannot get the Guest Network feature to work.Even though Guest SSID is enabled, it does not show up on any devices attempting to connect. Manually connecting by entering the Guest SSID fails (not recognized). On devices with the primary 5 and 2.4 GHz configured they do see the third network but without SSID (unknown) and are also unable to connect to it manually using the SSID.I did not try this before 1.0.02. Have rebooted modem and verified all configs (multiple times). The network is live in an office and can't keep screwing with it or drastically changing its settings.
View 9 Replies View RelatedLinksys Wireless Router :: Change Guest Network Name On E4200?
Nov 11, 2011Is it possible to change the Guest Network Name on the E4200? And if so, is it possible to do so without having to do a complete reset of the router and without using the Cisco Connect software?
View 4 Replies View RelatedLinksys Wireless Router :: E4200 Set For Single Guest But More Than One Connected?
Jul 14, 2011I tried searching through the threads but didn't see anything on this. Recently bought the E4200 so that when guests come by they can use a separate network instead of mine. I have guest network set up for one user but I am able to connect more than one computer to the guest network.
View 9 Replies View RelatedLinksys Wireless Router :: E4200 V1 - Mac Filtering And Guest Network?
Dec 12, 2011just picked up a E4200 v1.
does the mac filtering also apply to the quest network?
I normally have it set to allow macs for the wireless devices i own.
does the mac filtering apply to the quest network?
Linksys Wireless Router :: E4200 Will Not Open Guest Login Page?
Jun 11, 2011When Im connected to the GUEST network and open the web-browser it will not open the Linksys guest-login page. Why?(latest firmware ver.1.0.01(Build10) installed)
View 9 Replies View RelatedLinksys Wireless Router :: E4200 Guest Network Advanced Settings?
Aug 7, 2011I am interested to know if there is anywhere (even in the code) where i can play with the guest network settings?
*. ability to change the default webpage login for guest network
*. Ability to set a lease time for guest network
*. Ability to use special characters in the password (@!$%)
is it even possible or an open source firmware is the way to go?
Linksys Wireless Router :: E4200 Control On / Off Time Of Entire Guest Network
Sep 22, 2011Can i control the on/off time of the entire guest network?Or can use parental control for computers logged onto the guest network?
View 1 Replies View RelatedLinksys Wireless Router :: E4200 Disable Dhcp But Keep Guest Wifi Network
Mar 15, 2012My router a E4200. the thing is i want to disable the dhcp services from the router, because there are allready a dhcp server in my network. but if i disable the dhcp will the Guest wifi functions still work?
View 3 Replies View RelatedLinksys Wireless Router :: E4200 Guest SSID Login Page Fails?
Jan 25, 2011Config:
Netgear ProSafe Gigabit Router is my DHCP Server -- The entire home net work is on the same subnet (192.168.15.xxx)
Linksys E4200 configured as an access point ONLY -- wired connection -- static IP assigned -- DHCP server turned off
Linksys WRT610N configured as an access point ONLY -- wired connection -- static IP assigned -- DHCP server turned off
3 -- 5 port gigabit switches
1 -- 8 port gigabit switch
No more than two switches between any two wired devices Both Linksys access points have the same SSID and WPA2 security phrase -- total of 4 radios Nonoverlapping channels are selected on both the 2.4Ghz and 5.0Ghz radio to minimize interference All computers are running Windows 7 Professional 64bit with all the latest updates Two iPhones and one iPad also access the network All LAN and WAN connectivity is working as designed?
Problem:
guest SSID is turned on
password is established
All devices will connect to the guest SSID and the E4200 is assigning an ip address to the device in the 192.168.33.xxx range which is what it's supposed to do.When I open a web browser, I am not automatically redirected to the Cisco Login Page. If I enter 192.168.33.1 as the URL, the login screen is presented. I enter the password I have created in the guest admin page on the wireless guest tab. I then see a blank page and a URL of 192.168.33.1/guestnetwork.asp. THIS IS WHERE I GET STUCK. THE ONLY WAY TO EVER SEE THE LOGIN PAGE AGAIN IS TO REBOOT THE E4200, otherwise you just get unable to connect messages when opening web browsers and the wireless status icon in the system tray shows a yellow exclamation mark.
I successfully connect to the guest SSID but I do not get access to the internet. When I type ipconfig, I see that the DNS is set to 192.168.33.1 which does not exist on my network. I assume there's some internal NAT magic that is supposed to happen in the E4200 to bridge me over to my 192.168.15.xxx network but it doesn't seem to be happening.At the beginning of the call I specifically asked them if the E4200 must be the DHCP server in order for the guest SSID feature to work and they said no. 1.5 hours later they had no answers so they told me that it wasn't working because the E4200 was not the DHCP server. The documentation says nothing about a DHCP requirement for guest AP service. Linksys support further could not answer what you would do if you needed more than one AP with guest service enabled.It seems like this is a firmware issue but it may be the guest SSID service requires the E4200 to also act as the DHCP server. Whether this is a bug or if the router/AP is working as designed?
Linksys Wireless Router :: E4200 Guest Portal Displays As Not Being Password Protected
Jan 6, 2012My E4200 settings show both the 5.8GHZ and 2.4GHZ channels to be active, with SSID's displayed. However, when I look for available networks via my laptop(s)/tablets, etc, only the 2.8GHZ channel is visible. I've tried changing various settings and even updated the firmware but nothing has changed.
In addition my "guest" portal displays as not being password protected, even though it is setup for password protection in the E4200 menu.I've rebooted the router several times, but nothing has changed. The 5.8GHZ channel is not visible.The router is also performing frequent random disconnects, but that appears to be a separate issue, based on other posts.
Linksys Wireless Router :: E4200 - Change Text Of Guest Password Entry Pop Up On Message?
Sep 11, 2012I just bought a E4200, is there a way change the default text of the pop up message that is used when the client is requested to put in the password to access the guest SID for the e4200?
View 2 Replies View RelatedLinksys Wireless Router :: Guest Network Doesn't Work In Bridge Mode On E4200
Aug 9, 2011We have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
View 2 Replies View RelatedLinksys Wireless Router :: Configure One Of GigE Ports On E4200 To Only Work On Guest Network
Mar 17, 2012Is there a way to configure one of the GigE ports on the E4200 to only work on the "guest" network? Basically I have a need to setup one of those ports to get to the Internet, but I don't want it to be able to get to anything else on the private side.
View 1 Replies View RelatedLinksys Wireless Router :: Can't Access WRT54G Through IP Within Browser
Apr 7, 2012I can't access the router through the IP within the browser. It's an older WRT54G. I've never used the downloaded software that allows you to connect to it, but that's what I was going to try.
View 1 Replies View RelatedLinksys Wireless Router :: EA6500 Cannot Access Via Web Browser
Apr 28, 2013Before the latest update and with the latest update, after about one week, I cannot access the router wirelessly using 192.168.1.1. Using IE 10, Chrome, and FireFox all give me no response. I type in the address and the web page never changes. It keeps me at the home page of my browser. I do not get any errors or messages.
Also I tried to use the DHCP Reservation page, and the names of the devices will not allow spaces or any special characters. Sure would be nice to allow such.
I just noticed that my router reverted back to 1.1.28.146856. I have updated twice via the web browser to version 1.1.28.147876 and once via direct connection and the downloaded file, but the router keeps reverting back to the older firmware.
Linksys Wireless Router :: Unable To Access WRT310N Through Browser
Feb 9, 2009I am unable to access my router through the ip address (192.168.1.1) even though I have verified that is the address. To be sure, I did an ipconfig release/renew, but no results. I want to limit a user's network access by MAC address and I don't think I can do that without accessing the router thru the ip address.
View 2 Replies View RelatedLinksys Wireless Router :: Can't Access Admin (browser Based Utility) On E350
Jan 10, 2013I'm trying to access the browser based utility (@ http://192.168.1.1) on my router and having no luck. I've tried from two different computers (each Win 7) and each browser. I've tried wired directly to the blue/LAN ports and through Wifi. I've confimred that the IP is correct (or is at least the default gateway for each machine). The Cisco Connect tool can't find the router either.the only thing that can find the router is the CiscoConnect Express app on my iPhone.Internet is working fineish (some problems with Wifi), I just want to play with some settings.
View 1 Replies View RelatedCisco Wireless :: Linksys E4200 Guest Account
Mar 19, 2012We have a wireless router on our network 192.168.23.xxx and if the main router SSID is enabled we can connect to the internet, but am also connected to the network. I want to allow guests to use the wireless but not be able to see our network, I disabled the SSID broadcast and setup the Guest account and enabled the guest SSID broadcast. The note in the configuration says that guest will have to open a web browser and enter the password to use the internet. When connecting to the guest account nothing happens. I never see a login screen, nothing. I typed 192.168.1.1 into the address bar and it did oopen a login page for the guest account but does not connect to the internet. The network viewer says it is connected but the webpage says limited or no connectivity.
View 1 Replies View RelatedLinksys Wireless Router :: EA3500 Guest Access Keeps Going Down
Sep 7, 2012The guest network on the router keeps going down. It can be seen but it cannot be connected to. Sometimes it works for a day or 2 and then it doesn't. I have to constantly babysit the network and it is entirely frustrating because the only fix is to reboot the router.I have tried factory resetting several times.I have tried re-flashing the fw.I'm using the non-CCC fw because CCC had way, way too many issues.These routers have been out for months and many people have been having issues and somehow Cisco doesn't see fit to work on firmware that stabilizes them at all? It's like, they release a router and then forget about it - the next batch comes along, often the same guts with a different shell and it's the same thing over again. I had a WRT610N and I said I'd never buy another Cisco after that but I broke my rule because of being lured by these "App enabled" features, which mind you have nothing at all over the competition since the CCC doesn't even work for most people.
View 9 Replies View RelatedLinksys Wireless Router :: Guest Access On E3200?
Nov 14, 2011Purchased E3200 and did simple setup via CD setup (Cisco connect). Set up main name and password. Cisco Connect assigned "-guest" to end of main name for the guest account. Gave guest account its own password. Both main and guest accounts were broadcasting OK -- but guest account was not secure and could be accessed without password. (All software and firmware upgrades were done during initial setup).Reset the E3200 and restarted things from the CD setup. Created main account, main account password, and guest password again. In advanced settings, left basic wireless settings at initial settings, changed wireless secutiy to WPA2 Personal. Still having the guest account being broadcast in unlocked status. (Have turned off guest access for now until I can get password protection for it).
View 2 Replies View RelatedLinksys Wireless Router :: Enable Guest Access On E2000?
Feb 12, 2013How do I reenable guest access on my e2000 without having cisco connect installed?
View 1 Replies View RelatedLinksys Wireless Router :: Enable Guest Access On E1000
Sep 22, 2011I have a Linksys E1000 router. The firmware is 2.1.00 Build 7 August 30, 2010. I would like to turn on or enable the guest access function. I have gone to 192.168.1.1, and do not find anything there about guest access. At the Wireless tab, the choices are Basic Wireless Setting, Wireless Security, Wireless MAC filter, and Advamced Wireless Setting. Tfhan
View 9 Replies View Related