Is there a way to configure one of the GigE ports on the E4200 to only work on the "guest" network? Basically I have a need to setup one of those ports to get to the Internet, but I don't want it to be able to get to anything else on the private side.
View 1 RepliesWe have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
View 2 Replies View RelatedI have the wireless guest network up and running just fine. But, I need to also connect to the router's quest network via one of the ethernet ports. Can I just give the LAN-conencted PC a 192.168.3.x static IP to access the guest network? I am assuming there is no VLAN functionality...
And even better, can I set up a DHCP relationship to that port? So that any device plugged into the port will get a IP on that subnet?
I cannot get the Guest Network feature to work.Even though Guest SSID is enabled, it does not show up on any devices attempting to connect. Manually connecting by entering the Guest SSID fails (not recognized). On devices with the primary 5 and 2.4 GHz configured they do see the third network but without SSID (unknown) and are also unable to connect to it manually using the SSID.I did not try this before 1.0.02. Have rebooted modem and verified all configs (multiple times). The network is live in an office and can't keep screwing with it or drastically changing its settings.
View 9 Replies View RelatedIs it possible to change the Guest Network Name on the E4200? And if so, is it possible to do so without having to do a complete reset of the router and without using the Cisco Connect software?
View 4 Replies View Relatedjust picked up a E4200 v1.
does the mac filtering also apply to the quest network?
I normally have it set to allow macs for the wireless devices i own.
does the mac filtering apply to the quest network?
I am interested to know if there is anywhere (even in the code) where i can play with the guest network settings?
*. ability to change the default webpage login for guest network
*. Ability to set a lease time for guest network
*. Ability to use special characters in the password (@!$%)
is it even possible or an open source firmware is the way to go?
Can i control the on/off time of the entire guest network?Or can use parental control for computers logged onto the guest network?
View 1 Replies View RelatedMy router a E4200. the thing is i want to disable the dhcp services from the router, because there are allready a dhcp server in my network. but if i disable the dhcp will the Guest wifi functions still work?
View 3 Replies View RelatedI have just upgraded my E3200 to firmware: 1.0.04 build 1 Apr 10, 2012.The guest network SSID didn't show before in my access point list, but now I can't even change the settings on the router.The options are greyed out.
View 6 Replies View RelatedI have successfully set up a guest network on my EA4500. Guest laptop associates with guest SSID just fine. Then via IE, it gets prompted for the guest password, which is entered and accepted just fine. At this point guest laptop is on the network.
BUT... at some point the guest laptop will need to reauthenticate (I don't know what the timeout is, but maybe one or two days?). Anyway, it's at this point that IE presents the guest network login page. But now after typing in the password, "enter" or clicking on the button does nothing. It looks like the guest web page doesn't get loaded properly or completely, so the reauthentication can't complete, therefore can't get to the internet. So, while in this state, I've also tried Firefox and Chrome, and same thing, no action when trying to submit the guest password. Tried rebooting guest laptop, and still same problem. Only thing I've found so far that works is to reboot the router. So I'm guessing there's a problem with the guest/web server on the router?? It's a real pain to have to reboot the router every day or two, when I've had other Linksys routers run for months without having to touch them.
I was running CCC 2.1.38 when I first noticed the problem. Since then I've downgraded to Classic 2.0.37, but it seems I still have the same problem. Again, I can connect & authenticate just fine initially, but when reprompted after some period of time, it doesn't work.
I've tried contacting Cisco support, but it looks like I'm at 91 days since purchase and thus outside of my 90-day complimentary support, so they happily provided me with the premium support options just to have the honor of talking with them. Guess I shouldn't have spent so much time trying to figure this out myself.
The situation is Main house running Linksys EA4200, I have a garage apartment rental that is to far away to receive the wireless guest network.I ran a cat5e to the apartment, can I configure the EA4200 to allow the WAP54G access point to use the guest network? I want to prevent my renters from having access to the home network, but just have basic internet access separate/outside my network.
View 6 Replies View RelatedCan I turn off the wireless network of linksys E4200 and use only the 4 ports? using the router like a 4 port switch?
View 2 Replies View RelatedAny problems with the guest network on the ea4500 with the cloud firmware? I am losing guest clients after about 24 hours and the re-authentication fails. you enter the guest password and nothing happens until you reboot the router.
View 2 Replies View RelatedI am setting up six ISE 3355 appliances 3 in one datacenter 3 in another. They have just installed a new server farm infrastructure using Nexus 5596 and Nexus 2248TP top of rack switches.I have been looking for documentation on how to do NIC teaming on the 3355 or some way to connect Gig0 to FEX101 and Gig1 to FEX102. Or do I just setup a port channel using LaCP between the two different FEX groups?
View 1 Replies View RelatedIf you have MAC filter enabled with the E4200 Firmware Version: 1.0.01 you cannot connect to guest.
View 2 Replies View Relatedi enable guest access, when connecting though any device it doesn't ask for password but allows access straight away. I've tried changing the password, but no luck.
View 3 Replies View RelatedThe Guest Access is a very nice feature for allowing us to provide Internet access in our rental unit.
However, it would be nice to provide the Guests access to the USB printer.
Is there a way to provide access to the USB printer for those who are logged into the "Guest Network"?
I have the guest Access enabled on my E4200 but I can't get any of the apple devices or dell laptops to show the LOGIN screen in the web browser.
View 1 Replies View RelatedPurchased E4200 this week and did simple setup via CD setup (Cisco connect). Set up main name and password. Cisco Connect assigned "-guest" to end of main name for the guest account. Gave guest account its own password. Both main and guest accounts were broadcasting OK -- but guest account was not secure and could be accessed without password. (All software and firmware upgrades were done during initial setup).Reset the E4200 and restarted things from the CD setup. Created main account, main account password, and guest password again. In advanced settings, left basic wireless settings at initial settings, changed wireless secutiy to WPA2 Personal. Still having the guest account being broadcast in unlocked status. (Have turned off guest access for now until I can get password protection for it).
View 1 Replies View RelatedWith the E4200, is it possible to setup the main SSID with a pass pharse but have the guest SSID without a passpharse or password (ie access without security). If so, How?
View 1 Replies View RelatedMy serial number on the E4200 starts with 01 - does that indicate it is a version 1? If not, how do I determine which version I have? Are there any software updates available? How do I disable my guest access?
View 1 Replies View RelatedI tried searching through the threads but didn't see anything on this. Recently bought the E4200 so that when guests come by they can use a separate network instead of mine. I have guest network set up for one user but I am able to connect more than one computer to the guest network.
View 9 Replies View RelatedWhen Im connected to the GUEST network and open the web-browser it will not open the Linksys guest-login page. Why?(latest firmware ver.1.0.01(Build10) installed)
View 9 Replies View RelatedI have changed from dlink to linksys because of good reviews in transfer speed. Nothing to complained about that yet, Wireless guest zone has more to wishes... Disable password req is one, why call it guest and show it as an unsecured network (I know it separated from my local network and doesn't have encryption)? This password req is a bum when visitors with smartphones and ipods came and visit! More irritable is that somehow connection settings for guest in devices are lost when e4200 powercycle and every visitor must reconfig their devices again
View 7 Replies View Relatedwhat is the best way to remove configs from ports (GigE or Fa) in a 6500 that we aren't using anymore (i.e. best way to return a port to default). Remove each line one at a time or is there a command to default a port?
View 2 Replies View RelatedConfig:
Netgear ProSafe Gigabit Router is my DHCP Server -- The entire home net work is on the same subnet (192.168.15.xxx)
Linksys E4200 configured as an access point ONLY -- wired connection -- static IP assigned -- DHCP server turned off
Linksys WRT610N configured as an access point ONLY -- wired connection -- static IP assigned -- DHCP server turned off
3 -- 5 port gigabit switches
1 -- 8 port gigabit switch
No more than two switches between any two wired devices Both Linksys access points have the same SSID and WPA2 security phrase -- total of 4 radios Nonoverlapping channels are selected on both the 2.4Ghz and 5.0Ghz radio to minimize interference All computers are running Windows 7 Professional 64bit with all the latest updates Two iPhones and one iPad also access the network All LAN and WAN connectivity is working as designed?
Problem:
guest SSID is turned on
password is established
All devices will connect to the guest SSID and the E4200 is assigning an ip address to the device in the 192.168.33.xxx range which is what it's supposed to do.When I open a web browser, I am not automatically redirected to the Cisco Login Page. If I enter 192.168.33.1 as the URL, the login screen is presented. I enter the password I have created in the guest admin page on the wireless guest tab. I then see a blank page and a URL of 192.168.33.1/guestnetwork.asp. THIS IS WHERE I GET STUCK. THE ONLY WAY TO EVER SEE THE LOGIN PAGE AGAIN IS TO REBOOT THE E4200, otherwise you just get unable to connect messages when opening web browsers and the wireless status icon in the system tray shows a yellow exclamation mark.
I successfully connect to the guest SSID but I do not get access to the internet. When I type ipconfig, I see that the DNS is set to 192.168.33.1 which does not exist on my network. I assume there's some internal NAT magic that is supposed to happen in the E4200 to bridge me over to my 192.168.15.xxx network but it doesn't seem to be happening.At the beginning of the call I specifically asked them if the E4200 must be the DHCP server in order for the guest SSID feature to work and they said no. 1.5 hours later they had no answers so they told me that it wasn't working because the E4200 was not the DHCP server. The documentation says nothing about a DHCP requirement for guest AP service. Linksys support further could not answer what you would do if you needed more than one AP with guest service enabled.It seems like this is a firmware issue but it may be the guest SSID service requires the E4200 to also act as the DHCP server. Whether this is a bug or if the router/AP is working as designed?
My E4200 settings show both the 5.8GHZ and 2.4GHZ channels to be active, with SSID's displayed. However, when I look for available networks via my laptop(s)/tablets, etc, only the 2.8GHZ channel is visible. I've tried changing various settings and even updated the firmware but nothing has changed.
In addition my "guest" portal displays as not being password protected, even though it is setup for password protection in the E4200 menu.I've rebooted the router several times, but nothing has changed. The 5.8GHZ channel is not visible.The router is also performing frequent random disconnects, but that appears to be a separate issue, based on other posts.
I have the wireless guest access set up in my E4200 flash to the latest firmware. When I connect to the wireless guest network it comes up under the 192.168.33.xx IP address. I can connect fine but it never pops up the browser so that you can type in the guest password. I'm running Windows 7 but I've also noticed the exact same problem under XP.The only thing I can guess is the problem is that I have this acting like an access point and all DHCP requests go to my router. I've basically turned off DHCP on this and plugged the network connection into the switch on the back.
View 3 Replies View RelatedI just bought a E4200, is there a way change the default text of the pop up message that is used when the client is requested to put in the password to access the guest SID for the e4200?
View 2 Replies View RelatedI just upgraded to an E4200 from a D-Link DIR-655. I cannot seem to get my desktop to connect to the E4200 at 1 GBS. My adapter is set to "auto negotiate" but will only connect at 100 MBS. If I try forcing the adapter setting to 1 GBS, it never connects. I can swap out my E4200 with the DIR-655 and it will connect at 1 GBS just fine. I am using a CAT 5E cable. Is there something I'm missing here or is the E4200 just more finicky than the the DIR-655?
View 9 Replies View RelatedHave the issue of connecting a pc an NAS to a E4200 and when transferring from pc to NAS, only getting < 10 mbps transfer rates? NAS is Dlink 321. PC has Gigabit ethernet card. cables are cat 6. Even when I force the NAS and pc network card speeds to 1.0 GBps full duplex, I only transfer files at < 10 Mbps.
View 3 Replies View RelatedHow do I go about opening specific ports on an E4200?I'm having disconnect issues with a particular game, and the Customer Service drone thinks the ports required for the game aren't open. Nevermind the fact that it's worked fine for 6 months now, and the problem only started a few days ago.I figured I'd humor the idiot and open the ports, but all I can find is information on forwarding, not making sure the ports are open
View 3 Replies View Related