The situation is Main house running Linksys EA4200, I have a garage apartment rental that is to far away to receive the wireless guest network.I ran a cat5e to the apartment, can I configure the EA4200 to allow the WAP54G access point to use the guest network? I want to prevent my renters from having access to the home network, but just have basic internet access separate/outside my network.
View 6 RepliesIs there a way to configure one of the GigE ports on the E4200 to only work on the "guest" network? Basically I have a need to setup one of those ports to get to the Internet, but I don't want it to be able to get to anything else on the private side.
View 1 Replies View RelatedIs it possible to configure a E2500 as router and WAP54G as a repeater? I used to have a WRT54GS as router but it has broken and now I bought a E2500 to replace it.
View 2 Replies View RelatedAny problems with the guest network on the ea4500 with the cloud firmware? I am losing guest clients after about 24 hours and the re-authentication fails. you enter the guest password and nothing happens until you reboot the router.
View 2 Replies View RelatedI upgraded my Mac to OSX 10.8.1, with which the included connect software is incompatible. Downloaded the latest version from Cisco. It claims to be compatible with OSX 10.7 and up. Apparently 'up' does not extend to 10.8. When will we get an updated version of the connect software so that I can reconfigure my router?
View 1 Replies View Relatedhad a EA4200 about a year now, no probs, very stable, i'm thinking about getting a EA6500, for better coverage, iPhone apps, etc, would like to use my EA4200 in bridge mode from a EA6500, I'm a fairly new to networking etc, i'm assuming when the EA4200 is bridged, it will act like a repeater connected by cable, with same SSID ?
View 7 Replies View RelatedI am trying to use my EA4200 wireless as simply a router to run my home network. I want to leave all my cables plugged into it and distribute the internet via the switch to my other computers. I just want to turn of the wireless feature.
View 2 Replies View RelatedI live in a single story bungalow, and im wanting to resite my EA4200 up into the roof space, just wondering which is the best position to mount it in for signal, horizontal or vertical, or doesnt it matter ?
View 1 Replies View RelatedI have a wrt54gx2 with srx 200 technology recently purchased. I havetwo cabled computers attached. One at one end of the house attached tothe router by ehternet cable, the other attached about 100 ft by ethernet cable.The wireless does not reach to the other end of the house, most likley because that part of the house is an addition with masonary walls and a large masonary firplace. I bought a wap54g access point at the recommendation from someone at linksys to attach to the end of the ethernet run. Since my set up is macintosh, I can't use the wizard disk that came with the wap54g. Linksys support was not support( not expected), I need to know what to do to get this up and running. I am new to this stuff and Linksys get the wireless router with ethernet installed and up and running with my dsl. I thought the same for the wap54g.
View 2 Replies View RelatedI just took over a position where I had to reset a WAP54G because no one knew the encryption key. In working with some of the wireless access points in the past, I know that they came with setup or utility software to find and configure. where I can get a copy. I couldn't find it on Linksys' site.
View 3 Replies View RelatedMy network is such that I want to extend the signal of the GUEST account. I have a WAP54G set up for that purpose and am getting a very strong signal. I can access the main network, but not the Guest, I cannot even see the GUEST access. Any setting change that needs to be made that will allow me to access the GUEST account from the Access Point?
View 2 Replies View RelatedI have the wireless guest network up and running just fine. But, I need to also connect to the router's quest network via one of the ethernet ports. Can I just give the LAN-conencted PC a 192.168.3.x static IP to access the guest network? I am assuming there is no VLAN functionality...
And even better, can I set up a DHCP relationship to that port? So that any device plugged into the port will get a IP on that subnet?
Is there a way to get rid of the guest network on a E1000 or is it part of the setup.
View 1 Replies View RelatedI know the Guest network will allow people in my condo to use their wireless toys but does this open up the possibility of people next door for example using my network??
View 2 Replies View RelatedI cannot get the Guest Network feature to work.Even though Guest SSID is enabled, it does not show up on any devices attempting to connect. Manually connecting by entering the Guest SSID fails (not recognized). On devices with the primary 5 and 2.4 GHz configured they do see the third network but without SSID (unknown) and are also unable to connect to it manually using the SSID.I did not try this before 1.0.02. Have rebooted modem and verified all configs (multiple times). The network is live in an office and can't keep screwing with it or drastically changing its settings.
View 9 Replies View RelatedI just installed my EA4500 router and it was amazingly simple. My only question is it shows two wireless connections available: The secured one I set up and the another network with the same name that says "guest" and is NOT secured. Is there a way to either disable the unsecured guest network or to secure the guest network?
View 2 Replies View RelatedI am running a guest network on my E4200V2. I have changed my DNS servers on the router to use OpenDNS for traffic filtering. The filtering on my non-guest networks is working fine; the OpenDNS test sites are blocked. However, when I use the guest network, the OpenDNS test sites are not blocked. There's obviously nowhere that I can change the DNS settings for the guest network.
I know that parental filtering in the router applies to the guest network, however, it seems that the DNS servers for the non-guest networks don't apply to the guest network. Is this true? Have others seen this?If so, that's pretty disappointing. OpenDNS filtering is much more powerful than the 8-URL blacklist I can create in the router admin. If I want to filter sites for my kids, having a guest network that is essentially wide-open (except for 8 URLs) is not an ideal situation.
Our router is connected to my moms work computer. So on our main family computer we have a NET GEAR WG111v1 wireless adapter. When I do a scan for avaliable networks only the guest network is found. Our ipods can find the main secured connection but not the computer.
View 7 Replies View RelatedI have Cisco E4200v2, and after someone hacked my router's password, I was forced to activate a white listing MAC filtering. Problem is, that I would also like to enable a guest network so my small business's clients could still connect to the wifi, without having access to out home PC (and drinking our bandwidth).
View 9 Replies View RelatedI have just bought the EA3500 3 days ago.Also, I have been trying to find the way to rename the Guest Network to something without the -guest prefix.[url]....
View 1 Replies View RelatedIs it true that if someone wants to connect to the Guest network and macfiltering is on this is not possible. Which makes the guest network basicly useless.
View 5 Replies View RelatedIs it possible to change the Guest Network Name on the E4200? And if so, is it possible to do so without having to do a complete reset of the router and without using the Cisco Connect software?
View 4 Replies View RelatedI just installed and started using my E3000. Love it so far but I have a question about the guest network. I did set one up with a network name and password. It does show up under available networks but as an unsecured one. How do I go about securing it?
View 2 Replies View RelatedI want to setup a Linksys EA4500 in bridge mode behind my separate firewall to access the domain LAN. I'd also like to supply a wireless guest network for clients. In bridge mode the EA4500 doesn't seem to offer a separate guest network. Is there any solution other than adding another Wireless router just to serve up the Wireless Guest Network?
View 6 Replies View Relatedjust picked up a E4200 v1.
does the mac filtering also apply to the quest network?
I normally have it set to allow macs for the wireless devices i own.
does the mac filtering apply to the quest network?
Is there any way to configure a wired guest network with a combination of 5508 and 2504 wireless controllers? I am aware that the 2504 does not have wired guest functionality, however is it possible to set up a wired guest on the 5508 and using mobility anchors, transmit the l2 information through eoip to communicate with the remote vlan?Home built NAC solution, using 802.1x authentication on switchports for public areas. If user is an employee, communicates with the supplicant on their machine, and places them on an internal vlan.If user is a guest, user fails 802.1x check and is placed on a "guest" vlan with an ACL and external DNS.If placed on the guest vlan, the user has to accept a terms of use form.This is working currently with our 5508s without any issue, however we have some remote offices we'd like to roll this out to that are using 2504 controllers. I'm hoping there's a way that I can use the 5508 as an anchor or vice versa to make this work.
View 1 Replies View RelatedI haven't found a way to rename the Guest account on my E3000 router. If my router is named HomeRouter the Guest account automatically gets the name HomeRouter-guest. I have disabled the router's SSID broadcast, but it still broadcasts the almost identical Guest account.
View 4 Replies View RelatedI'm not sure why the guest net work is unsecured. I would have thought that would not be an option but it is unsecured. How to secure the guest network [2.4 GHz]? Also when I view the guest list some devices stay displayed whether they are in the vicinity or even turned off. That adds to my paranoia with the guest network being unsecured. I also can't edit the screen names to know who the device belongs to like is available in "my devices", forcing me to keep a MAC address list.
View 2 Replies View RelatedI currently use a E2500 router for my home network. I have setup the Wireless guest Network for my downstairs Tenant while he is out of work so he can still have some internet. The problem however is that often the guest network will take up 90% of my 55mb/sec bandwidth, leaving none for the primary network. Is there a way for me to Throttle the amount of bandwidth the Guest network can use? Say alot 10mb/sec for Guest access only, and leave the rest for our main network?
View 6 Replies View RelatedI have a wrt54g router and would like to separate the WLAN clients from accessing computers and servers on the LAN... in other words I would like to make it a "guest" network. I've put the router in "router" mode instead of "gateway". I just want to be sure if that is the best thing I can do in terms of turning the wireless network into an isolated one.
View 4 Replies View RelatedExperienced problems with guest network not showing up as an available network on a device (laptop, iPad, etc)?I double checked if guest network is enabled on a EA3500 router. What other steps can I take?
View 5 Replies View RelatedI have just upgraded my E3200 to firmware: 1.0.04 build 1 Apr 10, 2012.The guest network SSID didn't show before in my access point list, but now I can't even change the settings on the router.The options are greyed out.
View 6 Replies View RelatedI have a Linksys E2500 router. Is it possible to have one network name for the secured network and a different network name for the Guest network? The thought is to not have the SSID of the secured network broadcast while allowing the SSID of the Guest network to be broadcast. With the convention of simply adding "Guest" to the end of the SSID for the secured network, it defeats the security option of not having the SSID of the secured network broadcast.
View 1 Replies View Related