I am interested to know if there is anywhere (even in the code) where i can play with the guest network settings?
*. ability to change the default webpage login for guest network
*. Ability to set a lease time for guest network
*. Ability to use special characters in the password (@!$%)
is it even possible or an open source firmware is the way to go?
Manually type http://192.168.1.1/Wireless_Advanced.asp and the Advanced Wireless Settings tab appears! (I found this info in dd-wrt forum). A lot more settings to play with here, including transmission power for both 5GHz and 2.4GHz.
View 3 Replies View RelatedA few months ago I purchased an e2500 Cisco Linksys router to use in my home. This past Christmas, my family got about 4 new wifi devices which they added to the network bringing the total number of devices on my home network to 10. I wanted to know if there are any advanced settings in Cisco Connect that I can tweak to make my wifi speeds faster because right now I'm getting about 55 Mbps on most of my devices. I was also wondering what the typical range of the e2500 router was and if the e4200 offers a large improvement.
View 3 Replies View RelatedI want to know where I can edit advance settings of my EA6500. Cisco Clout Connect is too basic for my taste.
View 1 Replies View RelatedI've got a WPA wireless network set up that utilizes a total of 4 WRT54GL routers as access points (on channels 1, 6, and 11 [the two APs furthest from each other both utilize 11). Each AP generally supports about 5 clients at a time (though sometimes as high as 10).Generally, everything is working, but the clients furthest from the access points occasionally lose their connections, and some users have reported periods when they are completely unable to obtain an IP. I am virtually certain that this is based on poor signal strength resulting from distance from the APs and/or RF interference from other APs in the building. I have done everything possible to improve signal strength by router placement, optimizing channel usage based upon RF surveys, and upgrading to high-gain omnis.
This leaves nothing to do apart from tweaking the advanced wireless settings to marginally improve problems related to weak signal and/or RF interference, so I've been reading everything I can find on these boards and elsewhere about changing Fragmentation Threshold, RTS threshold, and beacon interval. However, I'm left with the following questions.
1) There seems to be disagreement about Fragmentation threshold and RTS threshold settings. Some (including the Linksys Technical Troubleshooting Wizard) recommend that both be set to 2304. I have also seen people insist that Fragmentation be set to 2306 and RTS to 2304. A few recommend 2306 for both thresholds, and some advise 2306 for Fragmentation and 2307 for RTS (though by my limited understanding, it simply disables RTS when the value is higher than the fragmentation threshold value). Which of these settings is best? And more importantly, WHY is it the best? Generally, I understand what the settings do, but I am reluctant to change them when there doesn't seem to be a consensus about exactly what they should be.
2) With respect to beacon interval, I've seen both 75ms and 50ms recommmended to replace the default of 100ms. For a network of my size (4 APs, averaging 5 users each), will increasing the number of beacons (and hence the RF traffic even when the network is idle) pose a problem? Also, I'm a little less clear as to how this would improve connectivity.
Since these settings will affect all users, I want to make sure that I'm using settings that will be beneficial on the whole. The last thing I want to do is inadvertantly make things worse, and since I can't test things directly from the standpoint of each user.
I use to use 2 routers, one for me and my dad, another for my brother and sister. We decided to get rid of the other router, and make our cisco E2000 our main router, but, everything on the router settings got removed so we had to reset it up. I remember reading an advanced setting guide on making my wireless speed go from 13.5MBPS to 216 MBPS, but i forgot what the settings was in advance settings.
View 7 Replies View RelatedI have the wireless guest network up and running just fine. But, I need to also connect to the router's quest network via one of the ethernet ports. Can I just give the LAN-conencted PC a 192.168.3.x static IP to access the guest network? I am assuming there is no VLAN functionality...
And even better, can I set up a DHCP relationship to that port? So that any device plugged into the port will get a IP on that subnet?
I cannot get the Guest Network feature to work.Even though Guest SSID is enabled, it does not show up on any devices attempting to connect. Manually connecting by entering the Guest SSID fails (not recognized). On devices with the primary 5 and 2.4 GHz configured they do see the third network but without SSID (unknown) and are also unable to connect to it manually using the SSID.I did not try this before 1.0.02. Have rebooted modem and verified all configs (multiple times). The network is live in an office and can't keep screwing with it or drastically changing its settings.
View 9 Replies View RelatedIs it possible to change the Guest Network Name on the E4200? And if so, is it possible to do so without having to do a complete reset of the router and without using the Cisco Connect software?
View 4 Replies View Relatedjust picked up a E4200 v1.
does the mac filtering also apply to the quest network?
I normally have it set to allow macs for the wireless devices i own.
does the mac filtering apply to the quest network?
Can i control the on/off time of the entire guest network?Or can use parental control for computers logged onto the guest network?
View 1 Replies View RelatedMy router a E4200. the thing is i want to disable the dhcp services from the router, because there are allready a dhcp server in my network. but if i disable the dhcp will the Guest wifi functions still work?
View 3 Replies View RelatedWe have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
View 2 Replies View RelatedIs there a way to configure one of the GigE ports on the E4200 to only work on the "guest" network? Basically I have a need to setup one of those ports to get to the Internet, but I don't want it to be able to get to anything else on the private side.
View 1 Replies View RelatedI have E4200 with fixed ip 192.168.1.2, DHCP off connected through LAN ports to FIOS ActionTec as 192.168.1.1. When connecting through wireless network off the E4200, I can obtain and connect fine under Guest network and WEP security, but for any other security setting, WPA, WPA2, Mixed mode, etc. I get the message "Aquiring network address" forever, and I never get a connection.
View 1 Replies View RelatedI recently bought a rtp300 and its on the 3.1.24 fw version I have been looking everywhere and i have not found any answer to my problem.It doesnt seem that you can change the pppoe settings (vpi,vci, encapsulation or PPP authentication ) anywhere. Should i return it If i apply the 5.01.04 i could those settings?
View 2 Replies View Relatedwhat is the optimal advanced settings for the ae2500 wireless adapter while gaming. I keep getting lag spikes with my games. Is there a always on option or like a gaming mode? If so what is it.
View 1 Replies View RelatedI Recently purchased the Linksys AE2500 adapter, upon looking at the advanced adapter settings, I couldn't find any more information pertaining to these settings on any linksys website or in fact online, where can I find a guide about these settings, Nothing about these setting was included on the CD.I set the basic one such as roaming aggressiveness but there are others that I would like to know about.
View 8 Replies View RelatedType of Wireless Adapter I have: Intel WiFi Link 1000 BGN When I click on (Properties) and then click the (Advanced) tab, there is a list of properties on the left and a list of values to choose from on the right. I'm curious on what each property does and, which property/value would be most "effective" or "appropriate" for a certain location/situation I'm in.
View 1 Replies View RelatedI have a E4200 router v.01 and when i updated the latest firmware (due to security exploit) it seems that whenever i acess the router settings (192.168.1.1) it doesn't ask me nor to input the admin and the password anymore, using wifi or wired.. I want the usual proccess whenever i go to 192.168.1.1 it will ask me to input my admin and password to change my router settings..
View 4 Replies View RelatedHow to configure settings for E4200
View 1 Replies View RelatedI just picked up a E4200 last nite and installed it and everything seems to be connecting ok, but I'm just not sure I have the optimal settings. This is my first dual band router.I have a mixture of G and N devices on the network - notebooks, desktop, phones, Wii. etc.What are the best settings for each of the 5 and 2.4 bands? I have read that you want to have the same SSID and encryption keys, so clients can go from one or the other seamlessly. It's mostly the Basic Wireless Settings that I want to get straight. Right now everything is on Mixed and Auto, and I'm not sure that's entirely correct.
Also, does anyone have any recommendations for a PCI and USB wireless adapter that works well with this router and provides the best range and throughput? I have both a laptop and desktop in a detached building with no physical cables. I want to ensure these have the best connection possible.
Any problems with the guest network on the ea4500 with the cloud firmware? I am losing guest clients after about 24 hours and the re-authentication fails. you enter the guest password and nothing happens until you reboot the router.
View 2 Replies View RelatedIf you have MAC filter enabled with the E4200 Firmware Version: 1.0.01 you cannot connect to guest.
View 2 Replies View Relatedi enable guest access, when connecting though any device it doesn't ask for password but allows access straight away. I've tried changing the password, but no luck.
View 3 Replies View RelatedThe Guest Access is a very nice feature for allowing us to provide Internet access in our rental unit.
However, it would be nice to provide the Guests access to the USB printer.
Is there a way to provide access to the USB printer for those who are logged into the "Guest Network"?
I have the guest Access enabled on my E4200 but I can't get any of the apple devices or dell laptops to show the LOGIN screen in the web browser.
View 1 Replies View RelatedPurchased E4200 this week and did simple setup via CD setup (Cisco connect). Set up main name and password. Cisco Connect assigned "-guest" to end of main name for the guest account. Gave guest account its own password. Both main and guest accounts were broadcasting OK -- but guest account was not secure and could be accessed without password. (All software and firmware upgrades were done during initial setup).Reset the E4200 and restarted things from the CD setup. Created main account, main account password, and guest password again. In advanced settings, left basic wireless settings at initial settings, changed wireless secutiy to WPA2 Personal. Still having the guest account being broadcast in unlocked status. (Have turned off guest access for now until I can get password protection for it).
View 1 Replies View RelatedWith the E4200, is it possible to setup the main SSID with a pass pharse but have the guest SSID without a passpharse or password (ie access without security). If so, How?
View 1 Replies View RelatedMy serial number on the E4200 starts with 01 - does that indicate it is a version 1? If not, how do I determine which version I have? Are there any software updates available? How do I disable my guest access?
View 1 Replies View RelatedI tried searching through the threads but didn't see anything on this. Recently bought the E4200 so that when guests come by they can use a separate network instead of mine. I have guest network set up for one user but I am able to connect more than one computer to the guest network.
View 9 Replies View RelatedCan I do this with a E4200? I want to do this for gaming reasons, and I mainly want to slow my speed down. I currently have my console hard wired to the router. I have accessed the firmware for the router but don't see how to change speeds.
View 2 Replies View RelatedI just purchased an e4200 in a corporate environment where we already have a wireless router. I am not able to connect the 2 devices via a LAN cable and am wondering if I can get bridge mode working over the network (wireless). I set the Linksys to bridge mode and assigned it an ip address. I disabled all wireless settings, etc. I then connected the internet port of the Linksys into a data port (wall jack) that connects to our flat network switch. It says it's connected under "Status" but I'm not sure how to confirm this.
View 3 Replies View Related